Valve Cover

Maintaining proper oil levels in your engine is crucial for peak performance. Undetected leaks can cause your oil to drop to dangerously low levels between oil changes, leading to severe engine damage.

One common culprit for oil leaks is the valve cover. Over time, exposure to extreme temperature fluctuations can wear down the gaskets, causing them to fail. Prevent oil leaks and protect your engine by replacing these vital components.

Comprehensive Kit Includes:

Valve Cover Gasket Set - Left & Right High Pressure Fuel Pump Gasket (2) O-Ring Seals (6) Torx Screws (6) Replace your old gaskets with our high-quality kit to keep your engine running smoothly and efficiently.

This complete kit provides all the gaskets you need for a thorough valve cover service.

Is your BMW M60 or M62 V8 engine leaking oil? You’re not alone. Oil leaks are a common issue, but we’ve got the perfect solution to keep your engine running clean and efficient.

The valve cover gasket is essential for keeping engine oil where it belongs – inside the engine. It ensures that your valve train and lifters are properly lubricated, preventing wear and tear. When this gasket fails, oil leaks out, creating a mess and potentially causing damage as it burns on hot engine components. Keep your engine compartment spotless and your BMW performing at its best with our valve cover gasket kit.

Original BMW replacement valve cover gaskets, including large cover gasket and spark plug cavity gaskets. Fits M57 engine. This is the OE BMW gasket rather than an OEM or aftermarket brand - we have found the OE gaskets are a better seal than the others. 

Genuine BMW Profile-Gasket -
This item fits the following BMW Chassis:
E70 X5,E90

Fits BMW Engines including:
M57
 

Keeping the oil inside your engine is extremely important to performance. Between oil change intervals, your oil can dip to dangerous levels if there is a leak you may not be aware of. The valve cover is an extremely common place for this to happen. BMW straight six engines are notorious for leaky valve cover gaskets. Years of exposure to extreme temperature change degrades the gaskets and causes failure. Replace yours to keep your engine oil in your vehicle.

This valve cover gasket set fits the folowwing BMWs with the M54 engine:

E39 525i 530i For vehicles with production date from 09/2002 
E46 325Ci 325i 325Xi 330i 330Ci 330Xi For vehicles with production date from 09/2002 
E53 X5 For vehicles with production date from 09/2002 
E60 525i 530i 
E83 X3
Z4 2.5i 3.0i

From the factory, BMW S65 valve cover bolts feature integrated non-serviceable grommets. These rubber seals tend to weaken, becoming brittle after years of heat and oil exposure. Replacing these bolts and integrated grommets can total over $280

To address this issue, NRW has developed a solution: a silicone replica of the factory rubber grommet, boasting a superior heat resistance of 170 degrees Celsius compared to the original's 120 degrees Celsius. Each kit contains 26 grommets, enough to service both valve covers.

Protect your Mini Cooper’s ignition coils and wiring from extreme engine heat with this direct-fit N18 ignition coil heat shield. Made from 18-gauge 304 stainless steel, it offers superior heat resistance, deflecting and dissipating damaging heat to extend the life of your ignition system.

This easy bolt-on upgrade installs using factory mounting points, no cutting or modifications required, and works with both plastic and metal valve covers. Its durable brushed finish provides long-lasting protection while keeping your engine bay looking sharp under high-heat conditions.

Upgrade your Mini’s ignition system today with this premium heat shield, engineered for performance, reliability, and effortless installation.

Design:

18-gauge 304 Stainless Steel
Specifically designed for the N18 engine for maximum coverage and heat shielding
Works with both plastic and metal valve covers
Utilizes the factory mounting stud found on the valve cover and the factory grommet found on the factory engine cover
Includes:

N18 Ignition Coil Heat Shield
Machined Mounting Standoffs
Heat Shield Grommet
Valve Cover Mounting Stud
Complete Installation Hardware
Product Development:
Engineered, tested, and quality inspected in-house by the ECS Tuning Research & Development team. Developed with FARO laser scanning, SolidWorks 3D CAD modeling, rapid prototyping, and rigorous long-term testing to ensure precise fitment, durability, and performance that meet ECS’s exacting standards.

This complete kit provides all the gaskets you need for a thorough valve cover service.

Is your BMW M60 or M62 V8 engine leaking oil? You’re not alone. Oil leaks are a common issue, but we’ve got the perfect solution to keep your engine running clean and efficient.

The valve cover gasket is essential for keeping engine oil where it belongs – inside the engine. It ensures that your valve train and lifters are properly lubricated, preventing wear and tear. When this gasket fails, oil leaks out, creating a mess and potentially causing damage as it burns on hot engine components. Keep your engine compartment spotless and your BMW performing at its best with our valve cover gasket kit.