This is the stock twin mass flywheel for early N54 engines in the E82 135i, E9X 335i/xi, and E60 535i/xi (flywheel uses 8 mounting bolts). It's manufactured by OEM Shaeffler (LuK). Sachs recommends a new dual mass flywheel (DMF) on every other clutch replacement. There are several indicators for replacing the flywheel: damage to the clutch contact plate (from a severely worn clutch disc), grease leaking from inside (overheating), build-up of clutch material on the contact plate (excessive slipping and overheating), and failure of the internal damping system.

The dampening system uses rubber or coil springs to absorb driveline vibrations. Through age, excessive heat, and aggressive use the rubber loses its resilience and the metal springs lose their strength and become brittle. If the clutch and flywheel have become overheated the internal grease may break down as well. A DMF failure can be massive and catastrophic, not to mention dangerous as bits of metal and rubber fling themselves through the transmission bellhousing. Heat and aggressive driving will accelerate the wear so race and track cars should have their stock flywheels replaced at regular intervals or with any new clutch. Even normal street cars should plan for a new flywheel if it has high mileage.

DMF wear can only be checked with the transmission and clutch removed. If you can rotate the outer flywheel more than 20mm in either direction then it should be replaced.

A new pilot bearing (roller bearing) is included, pre-installed in the flywheel hub.

OEM Schaeffler (INA, LuK, & FAG) is an engineering company that focuses on high-performance, precision manufacturing. With their individual brands INA, Luk, and FAG providing exceptionally high quality parts directly to BMW, as well as countless other automotive companies, their history of reliability and variety of offered parts makes Schaeffler a go-to replacement parts provider for all of us here at Turner Motorsport.

As a leading source of high performance BMW parts and accessories since 1993, we at Turner Motorsport are honored to be the go-to supplier for tens of thousands of enthusiasts the world over. With over two decades of parts, service, and racing experience under our belt, we provide only quality performance and replacement parts.  All of our performance parts are those we would (and do!) install and run on our own cars, as well as replacement parts that are Genuine BMW or from OEM manufacturers. We only offer parts we know you can trust to perform!

This item fits the following BMWs:
2008-1/2009 E82 BMW 135i
2007-1/2009 E90 BMW 335i 335xi 335i xDrive - Sedan
2007-1/2009 E92 BMW 335i 335xi 335i xDrive - Coupe
2007-1/2009 E93 BMW 335i - Convertible
2007-1/2009 E60 BMW 535i 535xi 535i xDrive

The factory dual-mass flywheel in your MINI N14 was built with comfort in mind—absorbing drivetrain vibrations and smoothing shifts—but at the cost of performance. Weighing in at a hefty 28.3 lbs., the OEM flywheel adds excessive rotational mass, dulling throttle response, slowing acceleration, and complicating precise rev-matching. Worse yet, it's known to be unreliable in modified or tuned setups and expensive to replace when it fails.

This single-mass design from ECS Tuning weighs just 18.8 lbs. It cuts nearly 10 lbs. of rotational weight to significantly enhance throttle response, acceleration, and overall driving feel. Built for durability and spirited driving, it's the ultimate upgrade for enthusiasts who want to make the most of every gear change.

Key Features:

Precision CNC-machined from 4140 HT Chromoly Steel: Ensures outstanding toughness, consistent wear, and long-term durability.

Heat Treated and Tempered: Achieves HRC 28-32 for improved strength, stress relief, and dimensional stability—even at elevated temperatures.

Black Oxide Coated: Resists corrosion for long-lasting protection and a professional finish.

Precision Balanced: Exceeds OEM standards (G16, 175 g-mm) to ensure smooth, safe operation at all RPMs.

SFI 1.1 Certified: Tested and approved for extreme use—track or street.

Direct Fit for OE N14 Clutch Kits: Maintains compatibility with factory-style components for hassle-free installation.

Performance Benefits:

Substantial Weight Reduction

​OEM Flywheel: 28.3 lbs.

ECS Lightweight Flywheel: 18.8 lbs.

Net Savings: Nearly 10 lbs.

Faster Revving and Sharper Throttle Response: Reducing rotational mass translates into a more dynamic and responsive driving experience.

Improved Clutch Engagement and Longevity: Optimized step height delivers better clamp load and extends service life.

Ideal for Modified MINIs: Built to handle increased power and spirited driving with confidence.

Replaces MINI OEM Part #: 21207575069

The factory dual-mass flywheel in W11-powered MINI Coopers was designed with comfort in mind—minimizing drivetrain vibration and delivering smoother shifts. However, this focus on refinement comes at a performance cost. The hefty 27 lbs. of rotational mass dulls throttle response, slows acceleration, and makes rev-matching more difficult. Dual-mass flywheels are also known to be less reliable in tuned or modified setups and can be expensive to replace when they fail.

ECS Tuning developed their Lightweight Single-Mass Flywheel to address these issues with a performance-focused alternative. Weighing in at just 17 lbs., this flywheel sheds nearly 10 lbs. of rotating mass compared to the OEM unit—transforming throttle response, acceleration, and clutch feel for a more engaging and dynamic driving experience.

Key Features:

Manufactured from 4140 Chromoly Steel
Heat-treated and tempered for exceptional strength, wear resistance, and thermal stability.
Optimized Hardness (HRC 28–32)
Ensures consistent performance and durability under extreme conditions.
Precision-Balanced to G16 Standard (175 g-mm)
Exceeds OEM balance requirements for smooth, high-RPM operation.
Black Oxide Finish
Provides effective corrosion resistance and a sleek appearance.
SFI 1.1 Certified
Validated for safe use in high-performance and racing environments.
Direct Fit
Engineered to work seamlessly with OE-style clutch kits designed for the W11 engine architecture.
Performance Benefits:

OEM Flywheel Weight: 27 lbs
ECS Lightweight Flywheel Weight: 17 lbs
This significant weight reduction results in:

Sharper throttle response
Faster engine revs and acceleration
Improved clutch engagement and feel
Increased performance potential for modified vehicles
OEM & Aftermarket Compatibility:

Replaces OE Flywheel #: 21207532057
Compatible Clutch Kits:
MINI OE: 21207551384
Spec: SB001, SB003
Clutch Masters: 03050HD00R
Recommended Hardware:

Flywheel Bolts: 11227560579 (Qty 8)
Pressure Plate Bolts: 21207520449 (Qty 6)

MINI R5X Adjustable Clutch Pedal Stop - Complete Install Kit

Improve the clutch pedal feel of your Mini with the MINI R5X Adjustable Clutch Pedal Stop - Complete Install Kit. This kit includes everything needed for a complete installation and adjustment of the clutch pedal stop. Enhance drivability and performance with precise clutch engagement and reduced pedal travel. Upgrade your Mini with this comprehensive clutch pedal stop kit.

• Complete install kit for easy installation
• Allows precise adjustment of clutch pedal stop
• Improves clutch pedal feel and drivability
• Reduces pedal travel for enhanced performance

The factory dual-mass flywheel in W11-powered MINI Coopers was designed with comfort in mind—minimizing drivetrain vibration and delivering smoother shifts. However, this focus on refinement comes at a performance cost. The hefty 27 lbs. of rotational mass dulls throttle response, slows acceleration, and makes rev-matching more difficult. Dual-mass flywheels are also known to be less reliable in tuned or modified setups and can be expensive to replace when they fail.

ECS Tuning developed their Lightweight Single-Mass Flywheel to address these issues with a performance-focused alternative. Weighing in at just 17 lbs., this flywheel sheds nearly 10 lbs. of rotating mass compared to the OEM unit—transforming throttle response, acceleration, and clutch feel for a more engaging and dynamic driving experience.

**This flywheel is to match with a factory type or aftermarket NON Dampened clutch kit!** MINIs factory set up engagement is dampened by the dual mass flywheel. This will be a little more aggressive engagement of the clutch over the stock factory set up as they system in not dampened!! Can be used from daily to the track days.

Key Features:

Manufactured from 4140 Chromoly Steel Heat-treated and tempered for exceptional strength, wear resistance, and thermal stability. Optimized Hardness (HRC 28–32) Ensures consistent performance and durability under extreme conditions. Precision-Balanced to G16 Standard (175 g-mm) Exceeds OEM balance requirements for smooth, high-RPM operation. Black Oxide Finish Provides effective corrosion resistance and a sleek appearance. SFI 1.1 Certified Validated for safe use in high-performance and racing environments. Direct Fit Engineered to work seamlessly with OE-style clutch kits designed for the W11 engine architecture. Kit Contents:

ECS W11 Lightweight Flywheel OEM LUK Clutch Kit OEM LUK Clutch Alignment Tool OEM LUK Release Bearing Genuine MINI Guide Tube Genuine MINI Flywheel Bolts (M10x48) Upgraded ARP Pressure Plate Screws (M9x15)