Cylinder Head and VANOS Tools

If you have ever attempted to do a valve job or cylinder head gasket project on an M42, M44, M50, or M52 engine you know that the repair manual will refer to the special BMW timing tool kit. This tool kit includes a flywheel locating lock pin, and a special set of camshaft locators that lock the cams in a precise location. The tools are very easy to install. The kit is specifically designed to hold the engine and cams in proper timing during the cylinder head removal and re installation process. This avoids the chance of bending the valves doing the head install process. The precision ground holding blocks lock over the square ends of both intake and exhaust cams. The CNC machined flywheel locating pin passes through a hole in the rear of the engine block and passed through a machined hole in the flywheel.

To avoid improper cam timing on the latest BMW engines, the factory has devised a cam timing system that locks the crankshaft and cams into a specific position prior to cylinder head removal. This method was devised to avoid any misalignment, resulting in piston to valve damage. Unfortunately without these tools re-timing the camshafts after a valve job is almost impossible. The factory specification manual does not supply installation specifications. This cam timing kit includes all the necessary components to do the job.

This item fits the following BMWs:
1990-1991 E30 BMW 318i 318is 318ic
1992-1998 E36 BMW 318i 318is 318ti 318ic 323is 323ic 325i 325is 325ic 328i 328is 328ic M3
1999-2005 E46 BMW 323i 323ci 325i 325ci 325xi 328i 328ci 330i 330ci 330xi

NOTE: Not compatible with S50B30 and S50B32 Euro engines!If you have ever attempted to do a valve job or cylinder head gasket project on an M42, M44, M50, or M52 engine you know that the repair manual will refer to the special BMW timing tool kit. This tool kit includes a flywheel locating lock pin, and a special set of camshaft locators that lock the cams in a precise location. The tools are very easy to install. The kit is specifically designed to hold the engine and cams in proper timing during the cylinder head removal and re installation process. This avoids the chance of bending the valves doing the head install process. The precision ground holding blocks lock over the square ends of both intake and exhaust cams. The CNC machined flywheel locating pin passes through a hole in the rear of the engine block and passed through a machined hole in the flywheel.

 

This gauge ensures that the inlet and exhaust cams are aligned perfectly. Make sure the edges are on the correct sides of the cylinder head before using.

Includes two alignment pin's which is ideal for inspection and servicing the motor with the timing chain still attached. If you are going to be removing the timing chain for service, you will need to lock both cams. 

The Ultimate kit includes every thing the standard kit does along with, a second alignment bridge, flywheel lock pin, VANOS alignment tools. and 4 bolt crank socket.

This tool fits all S54 powered BMW, including: 
2001-2006 E46 BMW M3
2001-2002 E36/7 BMW Z3M Coupe Z3M Roadster
2006-2008 E85/6 BMW Z4M Coupe Z4M Roadster
 

Looking to update your old torque wrenches? The Schwaben 3/8" Drive Digital Torque Wrench is your answer. 

This digital torque wrench uses an easy-to-read display to show torque amounts and settings, features a push button release, reversible 3/8" drive, 45 tooth ratchet head, and a comfortable no-slip grip and adjustment wheel.

Specifications:

• Setting Range: 45-220 ft lbs (60-300 Nm)
• Display Units: ft-lbs, N-m, Inch-lbs, cm-kg2, and m-kg
• Size: 22" (550mm) length for easy leverage
• Accuracy: +- 3%
• Include blow molded holding case
• Requires one 3V CR2030 battery (included)

BMW E60 M5 Crank Case Test Cap

The BMW E60 M5 Crank Case Test Cap is designed to facilitate accurate testing of crankcase pressure across a range of vehicle models. This versatile test cap is compatible with early and late model vehicles equipped with steel, aluminum, or plastic valve covers. Featuring a multi-diameter fitting, it connects directly to IMIBs, handheld manometers, and smoke machines, eliminating the need for adapters and ensuring precise readings without leaks.

Benefits:

• Versatile Compatibility: Suitable for use with steel, aluminum, and plastic valve covers on early and late model vehicles.
• Direct Connection: Multi-diameter fitting allows direct connection to IMIBs, handheld manometers, and smoke machines.
• Leak Prevention: Eliminates the need for adapters, reducing the risk of leaks and inaccurate readings.
• Enhanced Accuracy: Provides reliable crankcase pressure testing for better diagnostic results.

BMW recommends valve adjustments every 30k miles on your S54 equipped BMW. We have all the parts you will need to do the job in one discounted package. The kit includes all the Genuine BMW valve shims, valve shim tool, and all the gaskets and seals you will need.

Kit includes:
11127832034 x 1 - Valve Cover Gasket
11127831271 x 6 - Spark Plug Hole Gasket
11121437395 x 2 - Valve Cover Seal Washer Grommet
11127830972 x 13 - Valve Cover Nut Grommet
11340031525 x 1 - Valve Shim Set
83300493743 x 1 - Valve Shim Tool

*Click here for valve adjustment instructions*

This item fits the following BMWs:
2001-2006 E46 BMW M3, M3 Convertible2001-2002 Z3 BMW M Roadster M Coupe2006-2008 Z4 BMW Z4 M Roadster M Coupe