Packaged by Turner BMW Engine Parts

N54 HPFP failure is common with BMWs that use this powerplant. Our Packaged by Turner N54 High Pressure Fuel Pump Replacement Kit includes everything you need to replace your N54 HPFP.

Kit includes:

• Genuine BMW Re-manufactured High pressure fuel pump
• Intake manifold gasket sets  
• Throttle body gasket 
• Low pressure fuel sensor 
• High pressure fuel sensor 

The rubber hoses and oil separator can crack or become faulty, leading to vacuum leaks or oil leaks. This is caused by the stress the components are exposed to during heating and cooling cycles, especially if the vehicle is not brought up to operating temperature during driving in cold weather climates.

This kit includes the needed hoses, oil separator, mounting grommet, and hardware.

Fits the following BMWs:
1998-2003 E39 BMW M5

 The timing belt on the M20 engine should be replaced every 50,000 miles. The Gates Racing's timing belt this kit includes  is constructed of HNBR elastomeric composites. That being said, they are 300% stronger than the OE belt & deliver up to three times the heat resistance. Also included in this kit are the following:

• Gates Racing Timing Belt
• Tensioner
• Tensioner Spring and Bolt
• Water Pump & Gasket
• Thermostat & Gasket
• Camshaft Seal
• 1 Liter of Coolant
• Radiator Drain Plug

This kit includes sufficient coolant for a water pump replacement. If you intend to perform additional cooling system maintenance, pick yourself up an additional bottle of coolant.

For vehicles with production date from 09/1987.For vehicles with production date from 09/1987.

Over time, accessory belts begin to wear out and crack. This can lead to the belt slipping, squeaking, or even snapping. Replace your belts and tensioners on a regular basis to ensure you don't end up stranded on the side of the road with a dead battery or over heated engine due to a bit of simple overlooked maintenance. This kit includes all of the items that will need replaced such as the belts, tensioners, and hardware.

Fits the following BMWs:
1989-1991 E30 BWM 318is

If your engine has higher mileage, don't neglect rod bearing replacement! These bearings are sandwiched between the connecting rod and crankshaft journal and are prone to failure due to overheating, lack of lubrication, or general wear. Replace your rod bearings and prevent a spun bearing.

Starting with ACL’s high-performance bearing shells, our Race Series bearings are built to withstand extreme RPMs and stress. Utilizing a "Duraglide" tri-metal construction and a high-strength overlay plate, these bearings offer superior oiling and heat resistance for high-RPM operation.

Our WPC-treated bearings take ACL’s already impressive design and enhance it even further. The WPC treatment process strengthens and smooths the bearing surface by firing high-speed, ultra-fine particles at the bearing shells, reducing friction and improving durability. This advanced surface treatment ensures smoother operation and improved heat dissipation, which are critical for any high-performance engine.

Kit includes

Turner Motorsport WPC-Treated Race Series Rod Bearing Shells (12) ARP Upgraded Connecting Rod Bolts Hardware for Oil Pan & Oil Sump Oil filter Liqui-Moly TOP TEC 6600 0W-20 - 6L Oil Drain Plug Elring Silicone Sealant (for oil pan) Assembly Lube (4 oz.)

2006-2007 E60 530i Stage 1 Performance Package
Peak Power Gain: +29hp / +29ft-lbs
Rev limit: 7000
Octane: 91 or higher

Our Stage 1 kit featuring a cold-air intake kit and matching performance software. The aFe intake is a cone filter with a heat-blocking shield around it. The larger surface area of the filter, combined with the heat shield, allow more cool air to enter the engine - creating more power and torque, a richer engine sound, and better throttle response. The kit is supplied complete with heat shield, intake tube, sealing materials, hardware, and install instructions.

Our flash software is tuned especially for a cold-air intake, maximizing the potential and providing smoother power delivery. We take the stock software and make adjustments for 91 octane (stock software is set around 87). We can get more power and torque, and increase fuel efficiency without affecting driveability or the life of the engine. The throttle response is also improved (quicker) eliminating unwanted and dangerous flat spots in the pedal response.

Our software fully maximizes the 'low-output' N52B30O0 engine in the 530i. Our software has been carefully developed on the dyno and the road to provide optimal power and torque gains at all RPM. We change the fuel, Valvetronic, and VANOS maps as well as revise the factory torque limiters. We have paid particular attention to increasing low and mid-range torque. The stock BMW software is hampered by settings for 87 octane fuel. By re-mapping the engine programming for 91 octane, we can make more power, torque, and improve fuel mileage - all without harm to the engine or affecting driveability. The throttle response is also improved (quicker) eliminating unwanted and dangerous flat spots in the pedal response.

There are two ways to install our software: mailing the ECU to us for a reflash or do-it-yourself install with our Turner Flash tool:

Mail-In Reflash - lower upfront cost but additional shipping charges. Minimum downtime of at least three days. We have a 24 hour turnaround on shipping the ECU back to you but factor in transit time. Expert installation of your software at our facility.
Turner Flash DIY tool - higher upfront cost but files are emailed back and forth. No downtime - you can still drive the car while we process your tune. Files are emailed back and forth - your stock file comes to us, a tuned file is returned to you. Easy install via Windows laptop. 

E60 530i Stage 1 Engine Upgrade includes:
aFe Cold Air Intake (filter, heat shield, intake tube)
Turner Motorsport Performance Software Flash

This item fits the following BMWs:
2006-2007 E60 BMW 530i 530xi