Find Parts That Fit Your Vehicle

Home
Engine Parts

BMW Engine Parts

Turner Motorsport has everything you need to upgrade your BMW through our stages of performance or to keep your car in peak condition with our range of the latest in proven OEM cooling parts. Upgrade your cooling system and engine performance with the selections below to give your BMW a performance and reliability advantage.

Sub-Categories

Electronics (2)

Sort By:

Fuel-It! Low Pressure Fuel Pump Upgrade Stage 3 - N54/55 E-Series ...

T#:403279

Part#: FILPFPK3

Back Ordered

Starting at $ 1,155.83 USD

Add to Wish List

Starting at $ 1,155.83 USD

Add to Wish List

This is a complete Low-Pressure Fuel Pump (LPFP) upgrade that replaces your stock LPFP assembly with a new E85 certified one. This solution provides up to 300% more flow than stock and this assembly can be purchased one of three ways to meet your needs. Trade-in: (Domestic and Canada) This option allows you to receive a rebuilt/upgraded stock bucket with two new Walbro 450 pumps, filters, and fittings to swap out your stock LPFP assembly and requires a $150 *core deposit. Trade-in: (Euro) This option allows you to receive a rebuilt/upgraded stock bucket with two new Walbro 450 pumps, filters, and fittings to swap out your stock LPFP assembly and requires a $300 *core deposit. New Build: This option includes a new VDO LPFP bucket that is upgraded with new Walbro 450 pumps, filters, and fittings. No core deposit required but is eligible for a core refund of $50 should you elect to return your *stock bucket. (US Spec only) All three options include the following: A complete plug and play solution by simply replacing your stock bucket. However, to utilize the secondary, an additional wiring harness must be installed. Two new E85 compatible Walbro 450 pumps Two new Walbro filters A custom fitting that is tuned to optimize the venturi and pump output Spare vent tube clip Wiring harness for the secondary Flow testing prior to shipping

Show More Show Less

Fuel-It! Flex Fuel Kit - N54/N55 E Chassis

T#:21242695

Part#: FFK-N5XA

In Stock

Sale - Save 4% $ 485.99

This product was last offered at the strikethrough price on
09-20-2026

Starting at $ 464.99 USD

Add to Wish List

Sale - Save 4%

$ 485.99

This product was last offered at the strikethrough price on
09-20-2026

Starting at $ 464.99 USD

Add to Wish List

If you are running E85 or ethanol mixes in your BMW, you need this kit! This is a complete plug and play kit to install a Bluetooth ethanol sensor in your E-Chassis BMW. This kit replaces the stock fuel lines from the fuel tank to the engine bay with an upgraded -6an E85 compatible fuel line and adds an ethanol sensor and Bluetooth analyzer to monitor your ethanol content. Includes both Bluetooth App & 5v analog output for JB4 or flash tuning. For your fuel line upgrade, choose the option that supports your current configuration. HPFP to the fuel tank: (Stock) This upgrade replaces both stock fuel lines with one upgraded continuous fuel line from the fuel tank to the HPFP and adds the ethanol sensor. Port Injection to the fuel tank: If you are running our port injection kit, this upgrade replaces the stock fuel lines from the tank to the engine bay, integrates the ethanol sensor and then utilizes a Y adapter to supply the HPFP and PI with fuel. Our custom fittings remove those tee's and extra fittings for a cleaner high flow setup. Non-Fuel-It! port injection to fuel tank: Choose this option if you are running a port injection kit that we did not manufacture or sell. This kit includes a longer 18" feedline from the Y to the port injection rail. You then cut the feed line to the length you need and install the included -6an female fitting or -6an female elbow to make the connection to your port injection rail. All of these kits utilize the BMS custom billet aluminum fittings to integrate with the stock fittings so no modifications are needed. *For the BMW N54 E-series JB4 platform connect the white wire to position #15 on the JB4 25 pin harness. Select WMI Ethanol Setup option 1 to enable pin location 15/16 flex fuel input. *For the BMW N55 E-series JB4 platform connect the white wire to position #16 on the JB4 25 pin harness. Select WMI Ethanol Setup option 1 to enable pin location 15/16 flex fuel input. *Ethanol Sensors don't actually read the ethanol content, the readings are based on the absence of gasoline, so if your fuel is contaminated your ethanol readings may be artificially elevated.

Show More Show Less

Fuel-It! Flex Fuel Kit - N54/N55 5 Series

T#:21242701

Part#: FFK-N5XB

In Stock

Sale - Save 4% $ 485.99

This product was last offered at the strikethrough price on
05-03-2026

Starting at $ 464.99 USD

Add to Wish List

Sale - Save 4%

$ 485.99

This product was last offered at the strikethrough price on
05-03-2026

Starting at $ 464.99 USD

Add to Wish List

This is a complete plug and play kit to install a Bluetooth ethanol sensor in your E-Series BMW. (Check compatibility for your platform below) This kit replaces the stock fuel lines from the fuel tank to the engine bay with an upgrade -6an E85 compatible fuel line and adds an ethanol sensor and Bluetooth analyzer to monitor your ethanol content. This kit features a 0-5 volt analog output that integrates with the JB4, analog gauge, or any other ECU or tuner that supports 0-5 volt input. All of these kits utilize a custom billet aluminum fittings to integrate with the stock fittings so no modifications are needed. For your fuel line upgrade, choose the option that supports your current configuration. HPFP to the fuel tank: (Stock) This upgrade replaces both stock fuel lines with one upgraded continuous fuel line from the fuel tank to the HPFP and adds the ethanol sensor. Port Injection to the fuel tank: If you are running our port injection kit, this upgrade replaces the stock fuel lines from the tank to the engine bay, integrates the ethanol sensor and then utilizes a Y adapter to supply the HPFP and PI with fuel. Our custom fittings remove those tee's and extra fittings for a cleaner high flow setup. Non-Fuel-It! port injection to fuel tank: Choose this option if you are running a port injection kit that we did not manufacture or sell. This kit includes a longer 18" feedline from the Y to the port injection rail. You then cut the feed line to the length you need and install the included -6an female fitting or -6an female elbow to make the connection to your port injection rail. *These kits are available for off-road use only *Ethanol Sensors don't actually read the ethanol content, the readings are based on the absence of gasoline, so if your fuel is contaminated your ethanol readings may be artificially elevated. *For the BMW N54 E-series JB4 platform connect the white wire to position #15 on the JB4 25 pin harness. Select WMI Ethanol Setup option 1 to enable pin location 15/16 flex fuel input. *For the BMW N55 E-series JB4 platform connect the white wire to position #16 on the JB4 25 pin harness. Select WMI Ethanol Setup option 1 to enable pin location 15/16 flex fuel input. *Ethanol Sensors don't actually read the ethanol content, the readings are based on the absence of gasoline, so if your fuel is contaminated your ethanol readings may be artificially elevated.

Project Cars

SELECT YOUR BMW

BMW Engine Parts

Sub-Categories

Fuel-It! Low Pressure Fuel Pump Upgrade Stage 3 - N54/55 E-Series ...

Fuel-It! Flex Fuel Kit - N54/N55 E Chassis

Fuel-It! Flex Fuel Kit - N54/N55 5 Series

Select Vehicle

Category

Brand

Price

Special Offers

Shipping

Narrow Results