BMW Engine Parts

Rogue Engineering has developed a power pulley kit that reduces the drag on specific pulleys while allowing others to remain at their same efficiency. This allows for perfect operation in daily driven vehicles without a hiccup or stutter. However, when the demand for power is requested, the power pulley kit allows for the freed power to become apparent.  The term "power" pulley is a bit of a misnomer. Underdrive pulleys actually free up power by reducing the drag caused by the accessories.  These pulleys are based off a calculated percentage from factory dimensions, so that particular component speeds are safely reduced without affecting their true purpose.

Rogue Engineering Power Pullies are CNC machined from 6061-T6, heat treated aluminum and specially coated with a MIL-A-8625 Type III hard coat anodize finish. This kind of anodizing is not to be confused with a Type II cosmetic anodize finish (typical colors such as red, blue, silver, green, etc.). The hard coat anodize finish actually builds a small surface layer on top of the aluminum, preventing wear.

Fits the following BMWs:
2000-2006 E46 BMW 323/325/328/330

BMW Supercharger Kits can be found all over the internet, but who should you choose to go with? If you want to go to with a forced induction system and want reliability and a driving feel that isn't adversely affected, the VF Engineering Supercharger Kit is one of the best options on the market. Included with every supercharger system is their custom proprietary VF.GIAC software that safely realigns all fueling and engine management parameters for optimal performance and long term drivability. Unlike many other options that are available, the VF Supercharger kit is designed to work with BMW's OEM parameters to minimize the likelihood of DTCs (Diagnostic Trouble Codes) and Check Engine Lights.

This 6.0 psi VF Engineering supercharger system is designed for simple bolt-on installation, remains fully OBD2 compliant, and can be installed in a single day, ready to run in approximately 8 hours. This kit is also non-intrusive and is fully reversible. 

The 6.0 psi manifold at peak boost was tested to be the optimal induction charge limit without aftercooling and offers max tourqe gains!

Upon ordering, you will be required to send your VIN number, ECU, and transmission type (auto or manual) to VF Engineering within 1 year of purchase for your software flash of the ECU.

This product is supported by a 1 year unlimited mileage warranty on the product only.

From the factory, all BMWs utilize soft rubber or fluid-filled engine mounts. Not only are these mounts prone to degradation, they also allow ample movement of the drivetrain. This translates to looseness in your driveline, commonly associated with missed shifts and a generally isolated feeling.

To improve upon this issue, Black Forest Industries designed these upgraded mounts from the ground up. Their stage one mounts feature a proprietary 85A durometer bushing and bracket/cup design. Maximizing bushing area while minimizing vibration gives this mount the advantage of having the best ride characteristics possible from a urethane mount.

Features:

Perfect fit: Utilizing laser-scanning technology permits seamless integration with the factory engine mount arms. Quality tooling: All bosses are matched replicas with stock locations, and all tool clearances and specs are maintained. Heavy-duty construction: The use of billet aluminum instead of cast creates a mount that is dramatically stronger than its factory cast-construction counterpart. Performance design: 85A durometer bushings are geared toward the spirited driving enthusiast who doesn't mind increasing NVH. Choose BFI Stage 2 for a quality mount that eliminates drivetrain movement.

Note: Stage 2 mounts increase NVH. Therefore, these mounts are not intended to be used on daily driven vehicles.

ARP - Connecting Rod Bolt Sets M60/M62 are the ultimate upgrade for BMW enthusiasts seeking to improve engine performance and reliability. Specifically designed for BMW M60 and M62 engines, these high-performance rod bolts provide exceptional strength and durability. Manufactured by ARP, a leader in automotive fastener technology, these bolts are ideal for both street and track applications, ensuring your engine maintains peak performance under extreme conditions.

Key Features:

• Superior Strength: Engineered with aerospace-grade materials, these bolts offer unparalleled tensile strength, making them perfect for high-RPM and high-power setups.
• Precision Fit: Each bolt is precision-engineered to ensure a perfect fit for BMW M60 and M62 engines, reducing the risk of engine failure.
• Enhanced Durability: Designed to withstand intense stress, these bolts improve engine reliability for both daily driving and racing conditions.
• Corrosion Resistance: The special coating on these bolts provides excellent resistance to corrosion, extending the life of your engine components.
• Easy Installation: With detailed instructions included, these bolts are easy to install, whether by a professional mechanic or a DIY enthusiast.

Turner Motorsport offers the ARP - Connecting Rod Bolt Sets M60/M62, ensuring BMW owners have access to top-quality parts to enhance their engine's performance and reliability.

BMW Supercharger Kits can be found all over the internet, but who should you choose to go with? If you want to go to with a forced induction system and want reliability and a driving feel that isn't adversely affected, the VF Engineering Supercharger Kit is one of the best options on the market. Included with every supercharger system is their custom proprietary VF.GIAC software that safely realigns all fueling and engine management parameters for optimal performance and long term drivability. Unlike many other options that are available, the VF Supercharger kit is designed to work with BMW's OEM parameters to minimize the likelihood of DTCs (Diagnostic Trouble Codes) and Check Engine Lights.

This 6.0 psi VF Engineering supercharger system is designed for simple bolt-on installation, remains fully OBD2 compliant, and can be installed in a single day, ready to run in approximately 8 hours. This kit is also non-intrusive and is fully reversible. 

The 6.0 psi manifold at peak boost was tested to be the optimal induction charge limit without aftercooling and offers max tourqe gains!

Upon ordering, you will be required to send your VIN number, ECU, and transmission type (auto or manual) to VF Engineering within 1 year of purchase for your software flash of the ECU.

This product is supported by a 1 year unlimited mileage warranty on the product only.

BMW Supercharger Kits can be found all over the internet, but who should you choose to go with? If you want to go to with a forced induction system and want reliability and a driving feel that isn't adversely affected, the VF Engineering Supercharger Kit is one of the best options on the market. Included with every supercharger system is their custom proprietary VF.GIAC software that safely realigns all fueling and engine management parameters for optimal performance and long term drivability. Unlike many other options that are available, the VF Supercharger kit is designed to work with BMW's OEM parameters to minimize the likelihood of DTCs (Diagnostic Trouble Codes) and Check Engine Lights.

This 6.0 psi VF Engineering supercharger system is designed for simple bolt-on installation, remains fully OBD2 compliant, and can be installed in a single day, ready to run in approximately 8 hours. This kit is also non-intrusive and is fully reversible. 

The 6.0 psi manifold at peak boost was tested to be the optimal induction charge limit without aftercooling and offers max tourqe gains!

Upon ordering, you will be required to send your VIN number, ECU, and transmission type (auto or manual) to VF Engineering within 1 year of purchase for your software flash of the ECU.

This product is supported by a 1 year unlimited mileage warranty on the product only.

BMW offers their M Performance retrofit kit for your 340i/i xDrive & 440i/i xDrive for increased power and a more aggressive sounding and free flowing exhaust! This system directly from BMW is perfect for those looking for more power and an aggressive exhaust note without voiding the warranty! Upon installation, an immediate improvement is noticed, especially in the low to mid range powerband. The kit increases your vehicle’s power by 35 hp to 355hp and 39 lb-ft of torque to 369 lb-ft (355 lb-ft for manual transmission vehicles).The BMW M Performance Power kit now comes bundled with a higher flowing, valve controlled exhaust for maximum performance and exhilaration! The BMW M Performance Power Kit features engine tuning software and an electronically controlled valve exhaust system that is actuated in Sport/Sport+ modes via the driving experience control button. 

Included with the Power and Sound Kit:

• M Performance Muffler
• M Performance Decal Kit
• Stick on label and Badge
• Performance BMW software upgrade code
• Wiring Harness

After ordering this kit, simply take this to your dealer to have the ECU re-flashed and all of the components included installed! 

The muffler included must also be used with the following BMW exhaust tips:

• Carbon Fiber - Priced Each
• Chrome - Priced Each

*Dealer pricing for installation varies from dealer to dealer. Please contact your dealer for installation cost before purchasing.
 

Rogue Engineering has developed a power pulley kit that reduces the drag on specific pulleys while allowing others to remain at their same efficiency. This allows for perfect operation in daily driven vehicles without a hiccup or stutter. However, when the demand for power is requested, the power pulley kit allows for the freed power to become apparent.  The term "power" pulley is a bit of a misnomer. Underdrive pulleys actually free up power by reducing the drag caused by the accessories.  These pulleys are based off a calculated percentage from factory dimensions, so that particular component speeds are safely reduced without affecting their true purpose.

Rogue Engineering Power Pullies are CNC machined from 6061-T6, heat treated aluminum and specially coated with a MIL-A-8625 Type III hard coat anodize finish. This kind of anodizing is not to be confused with a Type II cosmetic anodize finish (typical colors such as red, blue, silver, green, etc.). The hard coat anodize finish actually builds a small surface layer on top of the aluminum, preventing wear.

This part fits the following BMW engines:
S54

This part fits the following chassis:
E46, Z3, Z4