Turbos

Ensure proper sealing when installing the turbos on your N54.

Kit includes:

• 16 - ASA M7x39 studs
• 16 - Flange nuts
• All required gaskets and o-rings
• Water pump install hardware
• Replacement vacuum hose
• T-bolt clamps

Helpful hints:

For complete installation instructions, refer to Haynes Service Manual (T#193950).

Both downpipes must be removed to remove either front or rear turbo. Tie rod end may need to be separated from knuckle for clearance. Steering rack may also need to be rotated away from subframe for access. Valve cover heat shield will need to loosened and pushed upward to get clearance for turbo manifold removal.

If studs back out of cylinder head and nuts are seized to studs, replace studs. Thread studs in to head by hand to prevent cross threading. When installing the new studs in the cylinder head, use a high temperature loctite in the cylinder head side, and copper anti-seize on the nut side.

To make more room for access to the front turbo, remove the rubber line running in front of the subframe that attaches to the back of the map thermostat and remove the clip. Cut off the OEM clamp and replace it with a new hose clamp as well.

Complete removal of the water pump is not required. Detach the water pump from the side of the block and push it out of the way to make more room for access to the front turbo. If water pump is unbolted from the block, the aluminum bolts must be replaced.

Torque specs:
Bracket to cylinder head: 9Nm
Coolant supply line to crankcase: 9Nm
Coolant return line to crankcase: 8Nm
Coolant return line to turbo: 8Nm
Coolant supply line to supply line: 8Nm
Exhaust manifold heat shield: 8Nm
Oil supply line to crankcase: 20Nm
Oil pressure line to turbo: 8Nm
Oil return line to crankcase: 8Nm
Oil return line to turbo: 8Nm
Turbo manifold to head: 20Nm

BRAKE BLEEDER:

We know bleeding brake alone is not only no fun, but much more complicated than it needs to be. Having a pressure bleeder give you the ability to keep the pressure on the brake system while you go under and crack open the bleeder screws to relieve the air pockets.

Features:

• Holds a full 3-Liters (3.17 qts) of brake fluid
• Easy to read 0-30 lbs pressure gauge built into the tank top
• Pressure relief valve for safe release of pressure
• 40" hose with detachable swivel fitting

Note:

• Do not exceed 20 PSI
• LIFETIME REPLACEMENT

Includes:

• 3 Liter (3.17 qts) storage tank
• Pressure cap with 0-30 lb gauge and pressure relief valve
• 40" hose
• Dual preventative fittings on the hose, featuring a chrome quick coupler on one end to snap onto the master cylinder cap and a detachable swivel fitting on the other end

Note:

• Recommend working at 10 PSI
• Dimensions for cap seal: 12x21x4 mm
• LIFETIME REPLACEMENT

CATCH BOTTLE:

Keep your fluid's off the floor and into our catch bottle.  The bottle has fluid level markings from 0.2L to 0.7 liter. This feature allows you to measure how much fluid you have sent thru the system.  Our bleeder bottle features an expandable/collapsible top portion for easier storage. Gasket in cap prevents leakage. Tubing is extra long at 24" from cap to nipple. Flexible hose can be pushed down into bottle for storage when done. Bottle now features a handy hanger bracket to hang bottle from bottom of car.

CALIPER HOOK SET:

Tired of messing with bent coat hangers or bungee cords to hang your calipers up and out of the way when performing brake maintenance? These hooks make working on your brakes easier by letting you hang your calipers with ease, no more fighting with the bungee cords or zip ties to hold the caliper just right or having to make your own "custom" hooks with wire.

• Holds brake calipers out of the way while working on brakes
• Also use to hang other automotive parts and tools while working on your vehicle.
• Stronger than zip ties or wire.
• Save the brake hose by not hanging caliper by hose.
• Made of  thick steel for strength and durability. length is 8"

BILLET ALUMINUM CAP:

This aluminum cap with 90 degree swivel will work with our T#363245 Euro bleeder or our T#366970 3-Liter Multi-functional Fluid Pump Kit.

Features an all aluminum 45mm cap with quick coupler nipple.

BLEEDER WRENCH:

Finally, a bleeder wrench with just the right angle to open the bleeder screw without having to spend all that time removing each wheel from your car.

WARNING: This product contains chemicals known to the state of California to cause cancer, birth defects, and/or reproductive harm. See above warning label as well as http://www.p65warnings.ca.gov for further information on Proposition 65 warnings.

Protect your Mini with the Turbo Heat Shield, an essential accessory to prevent hood paint discoloration, scoop warping, and underhood heat damage caused by excessive turbocharger heat. Additionally, it enhances the underhood appearance of your MINI. This metal plate mounts to factory points using supplied hardware, effectively reducing the amount of heat that bypasses the factory shield. While not encasing the turbocharger entirely, it serves as a secondary defense, complementing the factory-installed heat shield that isn't fully effective in preventing long-term hood paint and scoop damage.

• Prevents hood paint discoloration and scoop warping
• Guards against underhood heat damage caused by excessive turbocharger heat
• Enhances underhood appearance
• Mounts to factory points with supplied hardware
• Acts as a secondary defense in addition to the factory heat shield

Oil Supply Hose by Rein is a crucial part of your BMW’s engine system, designed to provide reliable oil flow to ensure optimal engine performance and protection. This high-quality hose is engineered to withstand the extreme temperatures and pressure that come with high-performance driving. Available at Turner Motorsport, the Rein Oil Supply Hose is a direct-fit replacement that helps maintain proper engine lubrication and prevents potential wear and damage to critical components.

• Specifically designed for BMW engines
• Delivers consistent oil flow to essential engine components
• Protects against engine wear and damage
• Engineered to withstand high temperatures and pressure
• Direct-fit for hassle-free installation
• Made from durable, high-quality materials for long-lasting performance

The Oil Supply Hose by Rein from Turner Motorsport is the ideal solution for keeping your BMW’s engine running smoothly, ensuring long-term reliability and performance.

BMW N54 3.0L Turbo Oil Feed Line - Rear Turbo is essential for supplying oil to the rear turbocharger of the BMW N54 engine. This high-quality oil feed line ensures reliable oil delivery, crucial for the optimal performance of the turbocharger. Designed to replace old or leaking lines, it helps prevent oil leaks, which can lead to severe engine damage. Replacing a worn or leaking oil feed line is crucial for maintaining the integrity of the turbo system and avoiding costly repairs.

• Ensures reliable oil supply to the rear turbocharger
• Prevents oil leaks that can cause engine damage
• Enhances turbocharger performance by providing consistent oil flow
• High-quality construction for durability and long-lasting performance
• Easy replacement of old or leaking oil lines

Positioned beneath the turbocharger on N20-equipped BMWs, this vital hose channels oil from the turbocharger back into the oil pan. Over time, wear and tear can lead to hose failure, resulting in significant oil leaks that may cause low oil levels and increase the risk of severe engine damage.

If your turbocharger drain hose is leaking or damaged, restore your engine's reliability with this high-quality replacement from Bremmen Parts. Engineered for durability and precision, it ensures a secure fit and long-lasting performance for peace of mind on the road.

Returns the coolant from the the turbo system to the cooling system.
When doing any sort of repair or maintenance there is no replacement for genuine factory parts. Turner Motorsport carries the Genuine BMW brand with pride and has the parts you need to complete your next project with confidence.

Genuine BMW Pipe, Return, Cooling For Turbocharger - Zyl. 4-6
This item fits the following BMW Chassis:
E89 Z4,E90,E92,E93

Fits BMW Engines including:
N54,N54T