Turbos

Ensure proper sealing when installing the turbos on your N54.

Kit includes:

• 16 - ASA M7x39 studs
• 16 - Flange nuts
• All required gaskets and o-rings
• Water pump install hardware
• Replacement vacuum hose
• T-bolt clamps

Helpful hints:

For complete installation instructions, refer to Haynes Service Manual (T#193950).

Both downpipes must be removed to remove either front or rear turbo. Tie rod end may need to be separated from knuckle for clearance. Steering rack may also need to be rotated away from subframe for access. Valve cover heat shield will need to loosened and pushed upward to get clearance for turbo manifold removal.

If studs back out of cylinder head and nuts are seized to studs, replace studs. Thread studs in to head by hand to prevent cross threading. When installing the new studs in the cylinder head, use a high temperature loctite in the cylinder head side, and copper anti-seize on the nut side.

To make more room for access to the front turbo, remove the rubber line running in front of the subframe that attaches to the back of the map thermostat and remove the clip. Cut off the OEM clamp and replace it with a new hose clamp as well.

Complete removal of the water pump is not required. Detach the water pump from the side of the block and push it out of the way to make more room for access to the front turbo. If water pump is unbolted from the block, the aluminum bolts must be replaced.

Torque specs:
Bracket to cylinder head: 9Nm
Coolant supply line to crankcase: 9Nm
Coolant return line to crankcase: 8Nm
Coolant return line to turbo: 8Nm
Coolant supply line to supply line: 8Nm
Exhaust manifold heat shield: 8Nm
Oil supply line to crankcase: 20Nm
Oil pressure line to turbo: 8Nm
Oil return line to crankcase: 8Nm
Oil return line to turbo: 8Nm
Turbo manifold to head: 20Nm

Vargas Turbo has done it again. They've made it even easier for you to get your car back on the road and running right again with your new turbos. They've put together an install kit containing all the components you need to get your new turbos installed properly and efficiently. This means you can get your car back on the road faster and enjoy your new turbos! 

Starting in 1978, Vargas Turbo Technologies was built upon the dream of utilizing then-new turbocharger technology to improve the performance of everything from cars to boats. On the cutting edge since the beginning, the company has grown with the industry, servicing diesel and industrial turbochargers. Returning to their hot-rod roots, Vargas has jumped head-first into the BMW performance market, filling a need for high-quality, cost effective turbocharger upgrades for everything from daily-driven street cars to all-out racing machines.

Experience an upgrade in your turbo system with the NM Eng Turbo Oil Line, which boasts a stainless steel braided line featuring precisely clocked banjo ends. This essential oil line provides a solution to a common issue – the oil leak that frequently occurs from the factory hard line. It's a must-have upgrade that's recommended every time you need to access the turbo by removing the bumper, replace the water pump housing, or enhance your intercooler.

It's important to note that an unchecked turbo oil line leak can result in serious consequences, including a messy oil spill, potential turbo starvation, and even the risk of fire when oil drips onto the catalytic converter, which happens to be the hottest part of your vehicle.

For a comprehensive solution, NM recommends replacing the return oil tubing simultaneously, utilizing the OEM part #: 11658617069.

Vargas Turbo has done it again. They've made it even easier for you to get your car back on the road and running right again with your new turbos. They've put together an install kit containing all the components you need to get your new turbos installed properly and efficiently. This means you can get your car back on the road faster and enjoy your new turbos! 

Starting in 1978, Vargas Turbo Technologies was built upon the dream of utilizing then-new turbocharger technology to improve the performance of everything from cars to boats. On the cutting edge since the beginning, the company has grown with the industry, servicing diesel and industrial turbochargers. Returning to their hot-rod roots, Vargas has jumped head-first into the BMW performance market, filling a need for high-quality, cost effective turbocharger upgrades for everything from daily-driven street cars to all-out racing machines.

Returns the coolant from the the turbo system to the cooling system.
When doing any sort of repair or maintenance there is no replacement for genuine factory parts. Turner Motorsport carries the Genuine BMW brand with pride and has the parts you need to complete your next project with confidence.

Genuine BMW Pipe, Return, Cooling For Turbocharger - Zyl. 4-6
This item fits the following BMW Chassis:
E89 Z4,E90,E92,E93

Fits BMW Engines including:
N54,N54T

OE Wastegate from BMW that regulates the vacuum/boosts levels of the exhaust. If this fails, it could severely disrupt performance and regular engine operation.
When doing any sort of repair or maintenance there is no replacement for genuine factory parts. Turner Motorsport carries the Genuine BMW brand with pride and has the parts you need to complete your next project with confidence.

Genuine BMW Pressure Converter
This item fits the following BMW Chassis:
E70 X5M,E71 X6M,E70 X5,E71 X6,E82,E89 Z4,E90,E92,E93,F02,F06,F10,F12,F13,F15,F16,F22,F25 X3,F26 X4 X4,F30,F31,F32,F33,F34,F36

Fits BMW Engines including:
N20,N26,N55,N63N,S63,S63N