Front Control Arm

BMW’s are known to have failure prone front thrust arm bushings.  The flexible rubber bushings, even those found in M performance models, allow significant movement of the front wheels to maximize daily driving comfort, but also allow considerable alignment change.  This results in a disconnected and numb road feel, standing between you and a confidence inspiring driving experience. Eventually the fluid filled rubber bushings fatigue and crack due to continual deflection and ozone degradation, and eventually the damping fluid leaks out resulting in complete failure.

For the enthusiast looking for superior performance and longevity with a crisp, confidence-inspiring driving experience, our sealed ball joint monoballs are the best solution available!  Our experience with spherical front control arm ball joints goes back to those we designed and used in our IMSA E90 328i and E92 M3 race cars (GS class Champions in 2011). We wanted to offer as many BMW owners possible a similar level of handling, precision, and control for the track and street.

Utilizing a sealed OEM BMW ball joint for exceptional quality and durability, making them completely at home on both the street and track with no compromise.  We have done extensive street, autocross, and track testing to ensure the ball joint used in this bushing design excels in each setting. The advantage of a sealed ball joint is that it eliminates all unwanted deflection while still allowing complete bind-free movement throughout suspension travel, resulting in exceptional control of wheel alignment.  What you get is superior steering precision, turn-in response, direct braking feedback, and better handling.

In short, if you're seeking the ultimate in precise, predictable handling and control, with crisp braking response and a long service life that’s equally at home on the street or track - look no further. We have you covered.

We offer these control arms with the monoball bearings pre-installed for your convenience. Since BMW recommends the control arms be replaced for every other bushing change, we prefer to sell these as a pre-assembled set. The bushings are also available separately if you wish to source your own control arms.

Control Arm Bearing

• CNC machined corrosion resistant 304 Stainless steel shell, bolt sleeves, & snap rings
• Sealed spherical ball joint for long service life & maintained OE fitment
• Suspension pre-load is no longer required when torquing the control arm hardware

Thrust Arm Bearing:

• OEM BMW sealed, greased ball joint for exceptional durability and service life, even in the most severe operating conditions
• 6061-T6 anodized housing for excellent corrosion resistance
• Proprietary Turner designed knurled OD to provide the perfect fit for the wide range of thrust arm bore diameters among brands
• CNC machined 304ss, providing a precision fit between the ball joint and the subframe

Benefits of Both:​

• Nearly instantaneous, crisp steering and braking response.
• Maintenance free, long lasting performance.
• Improved road feel without undesirable NVH.

Control arms begin to wear over time, leading to sloppy control of your vehicle. Anything from knocking, steering vibration, or even loss of vehicle control could occur. An OEM replacement from Lemförder is the perfect option to restore control and suspension quality.

OEM Lemförder is an engineering company that focuses on high-quality, precision manufacturing of critical suspension and steering components. Providing exceptionally high quality parts directly to BMW, as well as 50+ other big name automotive companies, such as Mercedes and Audi, their history of reliability and variety of offered parts makes them one of the biggest names for a go-to OEM parts provider. Lemförder parts place an important emphasis on design, production, and assembly, ensuring maximum reliability. They even coat all parts possible with corrosion protection for extended longevity.

As a leading source of high performance BMW parts and accessories since 1993, we at Turner Motorsport are honored to be the go-to supplier for tens of thousands of enthusiasts the world over. With over two decades of parts, service, and racing experience under our belt, we provide only quality performance and replacement parts.  All of our performance parts are those we would (and do!) install and run on our own cars, as well as replacement parts that are Genuine BMW or from OEM manufacturers. We only offer parts we know you can trust to perform!

This is the OEM Front Right Lower Control Arm for E39 BMW 525i 528i 530i 1997-2003.

This item fits the following BMWs:
1997-2003 E39 5 Series BMW 525i 528i 530i & Wagons

BMW’s are known to have failure prone front thrust arm bushings.  The flexible rubber bushings, even those found in M performance models, allow significant movement of the front wheels to maximize daily driving comfort, but also allow considerable alignment change.  This results in a disconnected and numb road feel, standing between you and a confidence inspiring driving experience. Eventually the fluid filled rubber bushings fatigue and crack due to continual deflection and ozone degradation, and eventually the damping fluid leaks out resulting in complete failure.

For the enthusiast looking for superior performance and longevity with a crisp, confidence-inspiring driving experience, our sealed ball joint monoballs are the best solution available!  Our experience with spherical front control arm ball joints goes back to those we designed and used in our IMSA E90 328i and E92 M3 race cars (GS class Champions in 2011). We wanted to offer as many BMW owners possible a similar level of handling, precision, and control for the track and street.

Utilizing a sealed OEM BMW ball joint for exceptional quality and durability, making them completely at home on both the street and track with no compromise.  We have done extensive street, autocross, and track testing to ensure the ball joint used in this bushing design excels in each setting. The advantage of a sealed ball joint is that it eliminates all unwanted deflection while still allowing complete bind-free movement throughout suspension travel, resulting in exceptional control of wheel alignment.  What you get is superior steering precision, turn-in response, direct braking feedback, and better handling.

In short, if you're seeking the ultimate in precise, predictable handling and control, with crisp braking response and a long service life that’s equally at home on the street or track - look no further. We have you covered.

We offer these control arms with the monoball bearings pre-installed for your convenience. Since BMW recommends the control arms be replaced for every other bushing change, we prefer to sell these as a pre-assembled set. The bushings are also available separately if you wish to source your own control arms.

Features:

Control Arm Bearing

• CNC machined corrosion resistant 304 Stainless steel shell, bolt sleeves, & snap rings
• Sealed spherical ball joint for long service life & maintained OE fitment
• Suspension pre-load is no longer required when torquing the control arm hardware

Performance

• Nearly instantaneous, crisp steering and braking response.
• Maintenance free, long lasting performance.
• Improved road feel without undesirable NVH.

Fits the following BMW models:

E39 -  525i, 528i, 530i

Here at Turner we understand the importance of an upgrade that will get the results you need on the track and still be tolerable on the drive around town. When it comes to control arms on the track, making them as stiff as you can (usually using solid mounts) is the best way to increase your driving precision by eliminating the deflection of rubber. The next best thing to create a balance would be to stiffen up the control arm with polyurethane, giving you the option of a more stock like feel with 80a or closer to the solid feel with 95a durometers. These poly bushings will give your control arms a direct connection between your suspension and the body of the car eliminating the slop felt under take-off and braking so you feel more in control of your vehicle. 

*Featuring a delrin sleeve to eliminate heat deformation and premature failure.

This item fits the following BMWs that use a centered-style bushing: 

2001-2006 E46 BMW M3 

Bushings tends to wear over time and split or even break free from the internal sleeve, causing excessive movement and sloppy control feel. OEM Lemförder bushings are the perfect option to restore suspension back to day 1 quality.

OEM Lemförder is an engineering company that focuses on high-quality, precision manufacturing of critical suspension and steering components. Providing exceptionally high quality parts directly to BMW, as well as 50+ other big name automotive companies, such as Mercedes and Audi, their history of reliability and variety of offered parts makes them one of the biggest names for a go-to OEM parts provider. Lemförder parts place an important emphasis on design, production, and assembly, ensuring maximum reliability. They even coat all parts possible with corrosion protection for extended longevity.

As a leading source of high performance BMW parts and accessories since 1993, we at Turner Motorsport are honored to be the go-to supplier for tens of thousands of enthusiasts the world over. With over two decades of parts, service, and racing experience under our belt, we provide only quality performance and replacement parts.  All of our performance parts are those we would (and do!) install and run on our own cars, as well as replacement parts that are Genuine BMW or from OEM manufacturers. We only offer parts we know you can trust to perform!

This item fits the following BMW Chassis:
E70 X5M,E71 X6M,E70 X5,E71 X6,F15,F16

Swapping in E46 control arms into your E30 or E36 significantly increases negative camber by widening the track width and also gives you more clearance for more steering angle. Condor's CNC machined control arm brackets are made from solid steel and are fitted with a solid hex-shaped bushing. Designed for the street or the track, they hold the control arm steady and eliminate "shimmy" caused by stock bushings. They sharpen steering and improve overall driving feel. Comparable to the NLA Treehouse E36 & E30 Eyeball Arms.

Easiest install of any aftermarket solution
Allow clearance for E30 M50 Conversion exhaust
Street Approved, marginal increase in NVH
Easy Installation, no need for a press
CNC machined steel construction
Solid design without the maintenance of spherical bearings
Heavy-Duty replaceable UHMW insert. Don't be misinformed, UHMW is the best material for these inserts. Delrin is not self-lubricating and will crack and degrade over time.
Powder coated white for corrosion resistance
Improve caster with M3 offset geometry
Keep proper steering geometry under high loads
Made in the U.S.A.
Fitment:
E30 84-91 3 Series
E36 92-98 3 series & Z3

Note that you will need to use E36 outer tie rods and E90 inner tie rods when installing in an E30 or E36

Be sure to measure your control arms to determine if you need 21mm or 23mm. Meyle makes a standard e46 control arm and a Heavy Duty control arm. Most HD arms have a hex that is larger in size (23mm). Lifetime Warranty

Control arm bushings play a key role in connecting the wheels to the chassis of the vehicle. Tasked with keeping suspension geometry in check while absorbing noise, vibration, and harshness (NVH) factory rubber bushings were engineered to provide a balance of comfort and control. As a factory bushing ages, it becomes brittle and begins to harden. When this happens the bushing will actually shrink and allow excess play in the suspension joint. This is typically felt by a sudden jerk forward after the car comes to a stop and is a leading cause of "sloppy" or "loose" suspension feel. By replacing the bushing with a full polyurethane unit or using a bushing insert, this play is eliminated since the suspension joint is being supported by a much stiffer material that will not harden or shrink over time. Additionally, the inherent stiffness of the urethane material translates body forces much more directly. This means steering inputs from the driver are effectively transferred to the wheels and vital road information is transmitted properly from the wheels to the driver.

Powerflex street bushings are ideal for street driven vehicles and those that see occasional autocross or track time. Need bushings for a dedicated track car? Powerflex Black Series bushings are the ultimate in track and race bushings. Featuring 95A durometer polyurethane, Black Series bushings are 25% stiffer than street bushings. Engineered to perform, Powerflex performance polyurethane control arm bushings offer a supreme level of control, while still providing enough comfort for the street, with advanced polyurethane that reduces NVH that often accompanies lesser bushings. Expect improved steering feel, turn in, more responsive handling and overall improved chassis composure with Powerflex performance polyurethane control arm bushings.

Poweflex is a leading manufacturer of aftermarket suspension bushings. Using state of the art design and manufacturing, all replacement bushings are engineered to out-perform and out-last the ones that came in the car. Each line of bushings is meticulously tested and then re-tested to ensure perfect fitment and enduring quality through the life of the vehicle. A full lifetime warranty backs every one of their products and demonstrates the level of confidence and commitment Powerflex has to their customers. 

BMW’s are known to have failure prone front thrust arm bushings.  The flexible rubber bushings, even those found in M performance models, allow significant movement of the front wheels to maximize daily driving comfort, but also allow considerable alignment change.  This results in a disconnected and numb road feel, standing between you and a confidence inspiring driving experience. Eventually the fluid filled rubber bushings fatigue and crack due to continual deflection and ozone degradation, and eventually the damping fluid leaks out resulting in complete failure.

For the enthusiast looking for superior performance and longevity with a crisp, confidence-inspiring driving experience, our sealed ball joint monoballs are the best solution available!  Our experience with spherical front control arm ball joints goes back to those we designed and used in our IMSA E90 328i and E92 M3 race cars (GS class Champions in 2011). We wanted to offer as many BMW owners possible a similar level of handling, precision, and control for the track and street.

Utilizing a sealed OEM BMW ball joint for exceptional quality and durability, making them completely at home on both the street and track with no compromise.  We have done extensive street, autocross, and track testing to ensure the ball joint used in this bushing design excels in each setting. The advantage of a sealed ball joint is that it eliminates all unwanted deflection while still allowing complete bind-free movement throughout suspension travel, resulting in exceptional control of wheel alignment.  What you get is superior steering precision, turn-in response, direct braking feedback, and better handling.

In short, if you're seeking the ultimate in precise, predictable handling and control, with crisp braking response and a long service life that’s equally at home on the street or track - look no further. We have you covered.

We offer these control arms with the monoball bearings pre-installed for your convenience. Since BMW recommends the control arms be replaced for every other bushing change, we prefer to sell these as a pre-assembled set. The bushings are also available separately if you wish to source your own control arms.

Control Arm Bearing

• CNC machined corrosion resistant 304 Stainless steel shell, bolt sleeves, & snap rings
• Sealed spherical ball joint for long service life & maintained OE fitment
• Suspension pre-load is no longer required when torquing the control arm hardware

Thrust Arm Bearing:

• OEM BMW sealed, greased ball joint for exceptional durability and service life, even in the most severe operating conditions
• 6061-T6 anodized housing for excellent corrosion resistance
• Proprietary Turner designed knurled OD to provide the perfect fit for the wide range of thrust arm bore diameters among brands
• CNC machined 304ss, providing a precision fit between the ball joint and the subframe

Benefits of Both:​

• Nearly instantaneous, crisp steering and braking response.
• Maintenance free, long lasting performance.
• Improved road feel without undesirable NVH.

Fits the following BMW models:

1995-2001 E38 BMW 740i 740il 750il 

Control arms begin to wear over time, leading to sloppy control of your vehicle. Anything from knocking, steering vibration, or even loss of vehicle control. An OEM replacement from Lemförder is the perfect option to restore control and suspension quality.

OEM Lemförder is an engineering company that focuses on high-quality, precision manufacturing of critical suspension and steering components. Providing exceptionally high quality parts directly to BMW, as well as 50+ other big name automotive companies, such as Mercedes and Audi, their history of reliability and variety of offered parts makes them one of the biggest names for a go-to OEM parts provider. Lemförder parts place an important emphasis on design, production, and assembly, ensuring maximum reliability. They even coat all parts possible with corrosion protection for extended longevity.

As a leading source of high performance BMW parts and accessories since 1993, we at Turner Motorsport are honored to be the go-to supplier for tens of thousands of enthusiasts the world over. With over two decades of parts, service, and racing experience under our belt, we provide only quality performance and replacement parts.  All of our performance parts are those we would (and do!) install and run on our own cars, as well as replacement parts that are Genuine BMW or from OEM manufacturers. We only offer parts we know you can trust to perform!

Control arms begin to wear over time, leading to sloppy control of your vehicle. Anything from knocking, steering vibration, or even loss of vehicle control could occur. An OEM replacement from Lemförder is the perfect option to restore control and suspension quality.

OEM Lemförder is an engineering company that focuses on high-quality, precision manufacturing of critical suspension and steering components. Providing exceptionally high quality parts directly to BMW, as well as 50+ other big name automotive companies, such as Mercedes and Audi, their history of reliability and variety of offered parts makes them one of the biggest names for a go-to OEM parts provider. Lemförder parts place an important emphasis on design, production, and assembly, ensuring maximum reliability. They even coat all parts possible with corrosion protection for extended longevity.

As a leading source of high performance BMW parts and accessories since 1993, we at Turner Motorsport are honored to be the go-to supplier for tens of thousands of enthusiasts the world over. With over two decades of parts, service, and racing experience under our belt, we provide only quality performance and replacement parts.  All of our performance parts are those we would (and do!) install and run on our own cars, as well as replacement parts that are Genuine BMW or from OEM manufacturers. We only offer parts we know you can trust to perform!

Bushings tends to wear over time and split or even break free from the internal sleeve, causing excessive movement and sloppy control feel. OEM Lemförder bushings are the perfect option to restore suspension back to day 1 quality.

OEM Lemförder is an engineering company that focuses on high-quality, precision manufacturing of critical suspension and steering components. Providing exceptionally high quality parts directly to BMW, as well as 50+ other big name automotive companies, such as Mercedes and Audi, their history of reliability and variety of offered parts makes them one of the biggest names for a go-to OEM parts provider. Lemförder parts place an important emphasis on design, production, and assembly, ensuring maximum reliability. They even coat all parts possible with corrosion protection for extended longevity.

As a leading source of high performance BMW parts and accessories since 1993, we at Turner Motorsport are honored to be the go-to supplier for tens of thousands of enthusiasts the world over. With over two decades of parts, service, and racing experience under our belt, we provide only quality performance and replacement parts.  All of our performance parts are those we would (and do!) install and run on our own cars, as well as replacement parts that are Genuine BMW or from OEM manufacturers. We only offer parts we know you can trust to perform!

Bushings tends to wear over time and split or even break free from the internal sleeve, causing excessive movement and sloppy control feel. OEM Lemförder bushings are the perfect option to restore suspension back to day 1 quality.

OEM Lemförder is an engineering company that focuses on high-quality, precision manufacturing of critical suspension and steering components. Providing exceptionally high quality parts directly to BMW, as well as 50+ other big name automotive companies, such as Mercedes and Audi, their history of reliability and variety of offered parts makes them one of the biggest names for a go-to OEM parts provider. Lemförder parts place an important emphasis on design, production, and assembly, ensuring maximum reliability. They even coat all parts possible with corrosion protection for extended longevity.

As a leading source of high performance BMW parts and accessories since 1993, we at Turner Motorsport are honored to be the go-to supplier for tens of thousands of enthusiasts the world over. With over two decades of parts, service, and racing experience under our belt, we provide only quality performance and replacement parts.  All of our performance parts are those we would (and do!) install and run on our own cars, as well as replacement parts that are Genuine BMW or from OEM manufacturers. We only offer parts we know you can trust to perform!

These bushings replace the stock rubber bushings and offer a better driving feel, increased lifespan, and better wheel alignment.

Rubber bushing allow for a lot more movement and are more susceptible to wear and tear from spirited driving and harsh weather conditions. Polyurethane is much more resistant to wear and is stiffer, reducing the total amount of movement that would normally affect the alignment negatively.