BMW Axleback Exhaust

Megan Racing Exhaust Systems for BMW

Upgrade your BMW's exhaust system with Megan Racing exhaust systems, crafted from 100% 304 stainless steel. Dyno-tested and proven to enhance power, these exhaust systems offer superior performance over your OEM restrictive exhaust. Enjoy a sportier exhaust note with the axle-back design. Constructed from stainless steel, Megan Racing exhausts are significantly lighter than OEM systems, improving the Power:Weight ratio and enhancing vehicle handling and performance. Plus, enjoy easy installation with no cutting or welding required.

• Made from 100% 304 stainless steel
• Dyno-tested for proven power gains
• Axle-back design for free-flowing performance
• Lightweight construction improves Power:Weight ratio
• Easy installation with no cutting or welding required

The combination of N52 and muffler delete surpasses all sound expectations from a small 1 series! Impressive direct-fit solution. With this new muffler/res delete you can completely transform the sound and driving experience of your 128. A simple installation that can be completed with hand tools gives you the ability to take your car to the next level at home in your garage! What sounds better than an in-line six-cylinder paired with a race-inspired exhaust setup, the answer is nothing. You have a nimble chassis fitted with an engine that provides more than enough power for spirited street driving or even taking to the track, if the exhaust is still factory you do not know what you are missing out on.

The ECS N52 Muffler & Resonator Delete removes the heavy, restrictive factory muffler and replaces it with a lighter weight, high flow, T304 stainless steel 3.0" exhaust tubing. This exhaust adds a louder exhaust note in a simple, cost-effective way without replacing the entire exhaust system and is fully compatible with the OEM rear valance. This upgrade creates a noticeable increase in exhaust sound, without adding significant drone at cruising speeds. As an added bonus, the ECS muffler delete shaves off about 16 lbs, weighing in at only 22 lbs. OEM units out of the 128 weigh in at around 38lb, a difference you will fully notice when upgrading your exhaust.

Features and Benefits:

Replace the factory muffler and resonator for a race-inspired straight 6-cylinder sound
Large radius bends for maximum exhaust gas flow
16lb weight reduction (Factory 38lb, ECS 22lb)
Fits in the factory exhaust hanger locations
Installation instructions featuring locations for removing your factory exhaust
Design:

In-house designed and engineered rear Muffler & Resonator Delete is made of T304 stainless steel, 1.25mm wall thickness, CNC mandrel bent 3.0" tubing for straight-through exhaust gas routing
High-quality stainless steel
Barbed exhaust hangers tig welded into the factory location for direct fitment
Stainless steel accuseal exhaust clamps included for a leak-proof seal
Large radius bends throughout with smooth transitions for the best flow possible

Special Doorbuster Deal: Turner DSSR with Purchase of the Turner Z3M Axle-Back Exhaust!

Elevate your Z3M’s performance and enjoy smoother, more precise shifts with this unbeatable combination. Purchase the Turner Motorsport Axle-Back Exhaust and receive a FREE Dual Shear Selector Rod (DSSR) — a powerhouse pairing that amplifies your driving experience.

Turner Z3M Performance Axle-Back Exhaust

Unleash your Z3M’s full potential with the Turner Performance Axle-Back Exhaust. Forget the heavy, restrictive factory exhaust — this system not only drops a significant 42 pounds but also provides a clean, aggressive tone that announces your arrival on the road or track.

Why Choose the Turner Z3M Exhaust?

While the E36 and E46 M3 models often steal the spotlight in the BMW performance scene, the Z3M, with its coveted S52 or S54 engine, offers an exceptional blend of power and handling. The Turner Axle-Back Exhaust embraces and enhances the Z3M’s capabilities, refining its sound, power, and aesthetic appeal for true enthusiasts.

With a straight-through muffler design, this exhaust optimizes exhaust flow, boosting throttle response, torque, and horsepower. Lightweight and meticulously engineered, it’s crafted to bolt right onto the factory mid-pipes for easy installation. Precision-designed for flawless fitment, it retains the OEM exhaust angle for a clean, OEM+ look.

Pro Tip: When swapping out your exhaust, check if your gaskets and mounts need refreshing for a completely seamless install.

Replacement Part Recommendations:

Gaskets – P# 18111723379 Round Hangers – P# 18211105635 Square Hangers – P# 18211704198 Exhaust Features and Benefits:

Weight Reduction: 60% lighter than stock — a whopping 42-pound weight loss. Enhanced Sound: Free-flowing design minimizes rasp for a refined, powerful tone. Precision Fit: Designed using FARO ARM laser scanning and CAD technology. Durable Build: Made from T304 stainless steel with a natural finish, 1.25mm wall thickness, and TIG-welded for durability. Increased Power: Mandrel-bent dual 2.5" stainless steel tubing reduces back pressure, enhancing performance. Aesthetic Upgrade: Quad-tip design for an eye-catching rear view. Kit Includes: Clamps, hardware, optional Turner exhaust tips, and a full rear exhaust section. FREE Turner Motorsport DSSR (389mm) for Z3M

Upgrade your Z3M’s shifting with Turner’s Dual Shear Selector Rod (DSSR). The DSSR provides a more solid connection, minimizing deflection and delivering a direct, precise shift feel. This meticulously crafted rod uses dual shear points to secure both ends of the shifter, translating every gear change into a crisp, controlled action — especially effective when paired with Turner’s poly rear shifter bushings.

Why Upgrade to the DSSR?

Imagine shifting with a single arm; you have control, but it’s limited. The DSSR uses both contact points, like gripping handlebars with both hands, offering a balanced and powerful connection. With its solid construction and minimized play, this DSSR keeps you firmly connected to your transmission for a completely immersive shifting experience.

DSSR Key Benefits:

Enhanced Shift Feel: Dual shear design for stability, minimizing unwanted movement. Perfect Fit: Precision-machined pins ensure seamless installation. High-Quality Materials: Constructed from 303 stainless steel for durability and corrosion resistance. Consistent Alignment: Maintains factory shifter length and angle for optimal ergonomics. Why Turner Motorsport?

Turner Motorsport’s exhaust and DSSR set are expertly engineered to bring out the best in your Z3M. With a focus on weight reduction, durability, performance, and precision, Turner’s products are a solid investment for those looking to elevate both their car’s performance and aesthetics.