Upgrade your OEM Gen1 B58 BMW charge pipe with our durable aluminum replacement, designed to prevent charge pipe failure.

Crafted from high-quality aluminum with a glossy black powder coat finish, this replacement charge pipe boasts CNC machined flanges, optional 1/8" NPT methanol bungs, and OEM-style mounting hardware for a seamless fit. It also features a vent-to-atmosphere blow-off valve flange for enhanced integration and performance.

The kit includes:

BMS Elite Aluminum Charge Pipe TurboSmart Race-Port BOV (3) 1/8" NPT Bung Plugs with Thread Sealer (1) 3" to 2.5" Silicone Reducer Coupler (2) 1/8" NPT to 1/4" Push-lock Fittings (1) 1/4" Push Tube Line (1) B58 Boost Tap Adapter Associated Hardware (Clamps, O-rings, Screws)

Upgrade Your S55 Powered BMW with VTT S55 Silicone Charge Pipes

Enhance turbocharger operation efficiency with VTT S55 Silicone Charge Pipes for your BMW. These pipes remove restrictions in the inlet and charge air tract, ensuring a full 2" ID from the turbochargers to the intercooler. Unlike factory pipes, which restrict airflow due to flattening, VTT charge pipes optimize airflow. Constructed of 7-ply wire reinforced silicone, they withstand over 150psi and feature an additional silicone layer for reduced heat soak. Choose from three color options: Black with Blue interior, Blue with Red interior, or Red with Black interior. This kit includes 2 silicone charge pipes, 2 billet turbocharger outlet adapters, and stainless steel clamps for easy installation on all S55 powered BMW M3/M4's.

Benefits:

• Eliminates restrictions for efficient turbocharger operation
• Provides a full 2" ID from turbochargers to intercooler
• Reduces potential heat soak with silicone construction
• Durable design tested to over 150psi
• Available in 3 color options: Black/Blue, Blue/Red, Red/Black

If you are looking to replace your stock chargepipe for better reliability and higher performance, the Burger Motorsports designed and Phoenix Racing built Performance Aluminum Chargepipe is an excellent choice! This aluminum chargepipe is significantly stronger than the stock plastic pipe and the powder coated aluminum looks great and will resist any corrosion. Plus, this chargepipe features a 3 inch design for optimal flow at all RPMs, prevent restriction that would normally be seen with the stock pipe. This is perfect for someone looking to upgrade a stock or tuned N54!

Specs and Features:

• Aluminum Construction
• Black Powder Coating
• 3" Diameter
• CNC Machined Throttle Body Flange
• Dual 1/8" NPT Bungs
• High Pressure T-Bolt Clamps
• All Required Installation Hardware

O-rings and retaining clip must be reused from the original pipe or purchased new for proper installation.

VTT is proud to offer the very best Cold Side charge pipe solution for the BMW E Series N54 platform. This system completely does away with the restrictive, and muli-connection stock charge pipe system, and replaces it with a single 6-ply, Heat Resistant, Wire reinforced silicone charge pipe rated at over 200 psi.  They are molded for the perfect fit in your engine bay, while not sacrificing anything in the way of flow or size. They also completely isolate your charge air from any additional heat soak coming in from the engine or ambient heat.  Another huge benefit is only TWO connections which are barbed and has many small ridges which dig into the silicone so it’s impossible for the pipe to blow off.

This N54 pipe has a flange installed to support a Turbosmart BOV.

This is the EASIEST N54 charge pipe on the market to install hands down. Install takes about half an hour even if you are inexperienced with working on your own car, can take as little as 15-20 minutes if you have had it apart a few times.

The kit includes:

VTT Cold Side Silicone Charge pipe

2 VTT Branded CNC adapters to mount the map sensor, and a methanol bung

1 VTT Branded CNC adapters for the TB inlet

2 VTT branded T-Bolt Clamps

1 1/8 NPT port is included in the charge pipe for methanol