VTT is happy to introduce the first and only available plug and play crankcase breather kits for ALL BMW applications that use the two-prong oil tab style oil fill caps. With this breather simply remove your oil cap, install the breather, and instantly free up horsepower, improve turbo draining, remove crankcase pressure, all while adding a cool look to your engine bay.
Can be used by itself with the stock PCV system to eliminate crankcase pressure, or with any number of PCV setups for the ultimate in crankcase pressure relieve
Made from 6061-T6 Aircraft aluminum anodized black for a long-lasting finish, 4 stainless steel baffles for complete oil control, a PTFE one way check ball, a high-quality filter, and clamp all work together to keep crankcase pressure where it belongs, out of your crankcase.
This breather will fit:
ALL BMW's with the two-prong style oil fill cap including but not limited to N54, N55, S55, S54
NOTE: NOT ALL THE MODELS LISTED HAVE THE SAME HOOD CLEARANCE, WE CANNOT SAY WHICH MODELS WILL HAVE CLEARANCE ISSUES, AND WHICH WILL NOT AS WE HAVE NOT TEST IT ON ALL MODELS. IF YOU ARE ORDERING THE BREATHER FOR ANYTHING OTHER THAN AN N54 TEST CLOSE YOUR HOOD CAREFULLY TO ENSURE CLEARANCE IF IT DOES NOT FIT LET US KNOW, AND WE WILL GET YOU A REFUND ONCE THE BREATHER IS RETURNED.
MODEL LIST OF REPORTED CLEARANCE ISSUES: N55 E/F 3 SERIES
The N54 suffers from a weak point in its crankshaft. It has been reported that when increasing the power to the engine, the crank hub can move or spin slightly under an extreme load. This is most apparent under high-rev downshifts or in the case of increased boost pressure which creates more stress on the engines rotating assembly. In order to keep this from happening, the crank bolt must be secured to the hub to keep it from backing off, but this can be a tricky solution since a simple dab of Loctite will not suffice.
Here is an easy, and cost-effective way to secure the situation; The VTT N54 crank bolt capture. This lightweight and durable ring slips over the head of the crank bolt fully encapsulating it, and locks it to the crank hub and eliminating its ability to spin. The VTT-CBC is 100% Billet Aircraft Grade Aluminum, Anodized black to protect it from the elements, and give it a stealth look. What's more is that it weighs only 1.3 Oz's meaning you aren't adding excess mass to the crankshaft which will avoid any imbalance or vibration issues.
While this is not a full fix for all crank hub spinning issues, the engineers at Vargas have found most issues have stemmed from the bolt itself backing out, and this is a great way to keep that from happening. Extremely lightweight at only 1.3 Oz's it adds virtually no weight to the crank which is important for balance and vibration.
Kit Includes:
This part fits the following BMWs:
2006-2013 N54
This product was last offered at the strikethrough price on
07-31-2026
This product was last offered at the strikethrough price on
07-31-2026
This product was last offered at the strikethrough price on
05-03-2026
This product was last offered at the strikethrough price on
05-03-2026
Stainless steel filtration is not a new technology but is quickly gaining popularity in the automotive segment. With the ability to filter down as small as a paper filter element with the ability to be washed and reused!
The K&P Engineering filter element is made from medical grade, type 304 stainless steel micronic filter cloth to provide unmatched protection against oil contamination and resultant engine damage. A one inch square of this material flows an incredible 1.9 gallons of oil per minute at only 1 PSI pump pressure. The adhesive used in the filter assembly process is good to 600 degrees Fahrenheit, far above normal engine operating temperatures. A super strength nickel-plated neodymium rare earth magnet is installed in the top of the element for magnetic pre-filtering of the oil. The sophisticated bypass is engineered for proper differential pressures and consistent operation, delivering a greater percentage of filtered oil while being very easy to clean. The twist lock design assures positive filter element placement and allows for easy disassembly, inspection, and cleaning. The quad-ring gasket doubles the seal between the filter and the engine. Finally, the filter housing is carved out of solid 6061T6 billet aluminum, which not only looks trick but aids in dissipating heat.
K&P Engineering manufactures stainless steel filters for a vast array of engines around the world. Staying at the forefront of design and testing allows this company to offer a top tier product for your European vehicle.
Features:
At regular oil changes, clean to K&P's specifications for continued used - a true lifetime filter.
This part fits the following BMWs:
2012+ F30 3 Series Sedan 328i 328iX 328i 328iX 335i 335iX
2006 - 2013 E9X 323i 325i 325xi 328i 328xi 330i 330xi 335i 335xi
2010 - 2016 F10 5 Series Sedan 528i 528iX 530i 535i 535iX
2003 - 2006 E60 Sedan 525i 525xi 530i 530xi
2007 - 2010 E60 528i 528xi 535i 535ix
2009 - 2016 E89 Z4 Roadster Z4 sDrive28i Z4 sDrive30i Z4 sDrive35i
2014+ F22 2 Series Coupe 228i 228iX M235i M235iX
2007 - 2013 E88 1 Series Convertible 128i 135i
2008 - 2013 E82 1 Series Coupe 128i 135i 135is 1M Coupe
2012 - 2013 E70 X5 xDrive35d X5 xDrive35i
2007 - 2011 E70 X5 3.0sd X5 3.0si
This product was last offered at the strikethrough price on
09-23-2026
This product was last offered at the strikethrough price on
09-23-2026
This product was last offered at the strikethrough price on
07-31-2026
This product was last offered at the strikethrough price on
07-31-2026
EXTRACTOR:
The Schwaben 6.5 Liter Extractor empowers you with swift, hand-operated fluid extraction. Complete with two tubes of varying diameters to suit your unique needs, this system's vacuum release button guarantees seamless operation. Clearing 6.5 Liters (6.8 qts.) of fluid in minutes, it preserves a spotless, oil-free workspace. Its ingeniously designed pour spout ensures mess-free fluid disposal.
Features:
ADAPTER:
This adapter hose allows a quick and easy suction thru the bleeder screw. This hose has included shut off valve in hose. This will improve your extractor capabilities and make it even more of an all-in-one tool!
WARNING: This product contains chemicals known to the state of California to cause cancer, birth defects, and/or reproductive harm. See above warning label as well as http://www.p65warnings.ca.gov for further information on Proposition 65 warnings.
Stainless steel filtration is not a new technology but is quickly gaining popularity in the automotive segment. With the ability to filter down as small as a paper filter element with the ability to be washed and reused!
The K&P Engineering filter element is made from medical grade, type 304 stainless steel micronic filter cloth to provide unmatched protection against oil contamination and resultant engine damage. A one inch square of this material flows an incredible 1.9 gallons of oil per minute at only 1 PSI pump pressure. The adhesive used in the filter assembly process is good to 600 degrees Fahrenheit, far above normal engine operating temperatures. A super strength nickel-plated neodymium rare earth magnet is installed in the top of the element for magnetic pre-filtering of the oil. The sophisticated bypass is engineered for proper differential pressures and consistent operation, delivering a greater percentage of filtered oil while being very easy to clean. The twist lock design assures positive filter element placement and allows for easy disassembly, inspection, and cleaning. The quad-ring gasket doubles the seal between the filter and the engine. Finally, the filter housing is carved out of solid 6061T6 billet aluminum, which not only looks trick but aids in dissipating heat.
K&P Engineering manufactures stainless steel filters for a vast array of engines around the world. Staying at the forefront of design and testing allows this company to offer a top-tier product for your European vehicle.
Features:
At regular oil changes, clean to K&P's specifications for continued used - a true lifetime filter.
This product fits the following BMWs:
1995 - 1999 E36 M3
2001 - 2006 E46 M3
1998 - 2002 E36/8 Z3 M Coupe
1998 - 2002 E36/7 Z3 M Roadster
2006 - 2008 E86 Z4 M Coupe
2006 - 2008 E85 Z4 M Roadster
MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.
This product was last offered at the strikethrough price on
05-02-2026
This product was last offered at the strikethrough price on
05-03-2026
This product was last offered at the strikethrough price on
05-03-2026
Stainless steel filtration is not a new technology but is quickly gaining popularity in the automotive segment. With the ability to filter down as small as a paper filter element with the ability to be washed and reused!
The K&P Engineering filter element is made from medical grade, type 304 stainless steel micronic filter cloth to provide unmatched protection against oil contamination and resultant engine damage. A one inch square of this material flows an incredible 1.9 gallons of oil per minute at only 1 PSI pump pressure. The adhesive used in the filter assembly process is good to 600 degrees Fahrenheit, far above normal engine operating temperatures. A super strength nickel-plated neodymium rare earth magnet is installed in the top of the element for magnetic pre-filtering of the oil. The sophisticated bypass is engineered for proper differential pressures and consistent operation, delivering a greater percentage of filtered oil while being very easy to clean. The twist lock design assures positive filter element placement and allows for easy disassembly, inspection, and cleaning. The quad-ring gasket doubles the seal between the filter and the engine. Finally, the filter housing is carved out of solid 6061T6 billet aluminum, which not only looks trick but aids in dissipating heat.
K&P Engineering manufactures stainless steel filters for a vast array of engines around the world. Staying at the forefront of design and testing allows this company to offer a top-tier product for your European vehicle.
Features:
At regular oil changes, clean to K&P's specifications for continued used - a true lifetime filter.
Watch to learn how to clean a K&P oil filter
This product fits the following BMWs:
1975-1983 E21 320i
1982-1991 E30 325i
1982-1988 E28 528i 528e
1989-1995 E34 525i
Stainless steel filtration is not a new technology but is quickly gaining popularity in the automotive segment. With the ability to filter down as small as a paper filter element with the ability to be washed and reused!
The K&P Engineering filter element is made from medical grade, type 304 stainless steel micronic filter cloth to provide unmatched protection against oil contamination and resultant engine damage. A one inch square of this material flows an incredible 1.9 gallons of oil per minute at only 1 PSI pump pressure. The adhesive used in the filter assembly process is good to 600 degrees Fahrenheit, far above normal engine operating temperatures. A super strength nickel-plated neodymium rare earth magnet is installed in the top of the element for magnetic pre-filtering of the oil. The sophisticated bypass is engineered for proper differential pressures and consistent operation, delivering a greater percentage of filtered oil while being very easy to clean. The twist lock design assures positive filter element placement and allows for easy disassembly, inspection, and cleaning. The quad-ring gasket doubles the seal between the filter and the engine. Finally, the filter housing is carved out of solid 6061T6 billet aluminum, which not only looks trick but aids in dissipating heat.
K&P Engineering manufactures stainless steel filters for a vast array of engines around the world. Staying at the forefront of design and testing allows this company to offer a top-tier product for your European vehicle.
Features:
At regular oil changes, clean to K&P's specifications for continued used - a true lifetime filter.
This part fits the following BMWs:
1991 - 1999 E36 Coupe 323i 325is 328i
1993 - 1999 E36 Convertible 323i 325i 328i
1990 - 1999 E36 Sedan 325i 328i
1989 - 1995 E34 525i, 530i,
1998 - 2004 E39 Touring 525i 528i
1996 - 2004 E39 Sedan 525i 528i 530i
1999 - 2001 E46 Convertible 323ci 325ci 330ci
2002-2006 E46 Convertible 325ci 330ci
1998 - 2001 E46 323ci 325ci 330ci M3
2002 - 2006 E46 325ci 330ci
1998 - 2001 E46 Touring 323i 325i
2002 - 2006 E46 Touring 325i 325xi
1998 - 2001 E46 Sedan 323i 325i 328i 330i
2002 - 2006 E46 Sedan 325i 325xi 330i 330xi
2000 - 2006 E53 X5 SUV X5 X5 3.0i
