Sensors

All vehicles will lose some degree of performance due to heat soak under the right operating conditions.  Engine management systems constantly monitor operating conditions and modifying parameters based on sensor inputs. BMW integrated the intake air temp sensor in the MAF housing on models such as the E39 M5, and, being sandwiched behind a hot radiator and in some applications next to an even hotter valve cover, this is less than ideal for performance applications. Absorbing excess heat from its surroundings, the MAF can’t shed it fast enough, and the ECU reads an inaccurately high intake air temperature. Compensating for this false hot air measurement, the ECU pulls timing and runs a richer fuel mixture, resulting in a significant loss of torque.

What can you do?  Locate an intake air temp sensor in a location where it can properly measure incoming air temps and where it's less prone to heat soak. Mounting the sensor further away from the heat source and isolating it from the MAF housing, it can both resist the effects of heat soak longer and respond to temperature changes more quickly.  The result is you’ll experience reduced torque loss and more consistent power output when you’re pushing your engine hard. 

The Turner engineering team was initially skeptical of the claimed performance benefits of this modification. They first set out validate the functionality and performance benefit of a temp sensor relocation. Replicating stop-and-go traffic heat soak in a 2001 540i was a simple task in a controlled environment - their dynometer. First the car was heat soaked to simulate being stuck in traffic or moving at low speeds by running the car four times on the dyno with the dyno's cooling fans disabled. The fans were then turned on for three more runs to observe the recovery rate once air flow was reintroduced. The test: following this procedure once with a stock IAT, and once with their relocation kit in place. 

The result? Turner recovered 11lb-ft torque at 2500rpm through use of their relocation kit, with even greater recovery to be found for M5 owners. Here are the heat soak-related torque losses Turner experienced:

Stock IAT location:
18rwtq at 2500rpm
10rwtq at 3000rpm
9rwtq at 3700rpm

Turner IAT Relocation:
7rwtq at 2500rpm
5rwtq at 3000rpm
5rwtq at 3700rpm

**Click here for installation instructions**

The Turner engineering team designed a complete plug and play kit (unlike all other options on the market) that makes for quick, easy, and reversible installation. Weather-sealed connectors keep out the elements, while sheathed wiring offers a clean appearance underhood. With a harness nearly 3 feet long - the Turner IAT relocation kit offers flexibility in positioning, but not too long that you're left with unsightly excess wiring. Turner recommends positioning the sensor in a location away from engine heat, but still within the intake ducting to achieve accurate intake temp readings - such as the far side of the base of the airbox. Vehicles with cold air intakes with cone-style filters can even position the sensor in the end of the filter. Simply drill a hole in your (cool) location of choice and plug in the harness. More information including installation instructions and some good examples of sensor mounting locations can be found in our DIY PDF. 

We include everything you need to relocate your IAT, just select your desired sensor brand below - Genuine BMW or original equipment Beru.

Also the perfect plug-n-play option for anyone looking to upgrade their intake to utilize an Alpha-N tune!

Note for vehicles with M62 engine: applicable to 1999 and up

The camshaft position sensor is essential for assisting the engine DME by monitoring the camshaft's position. The data from this sensor is key to optimizing ignition timing and ensuring smooth engine performance.

Often referred to as the CMP sensor, this component is crucial for the overall functionality of the powertrain. A failing camshaft position sensor can cause a range of issues, including engine stumbling, hesitation during acceleration, power loss, and even starting difficulties or complete failure to start.

Replacing your factory environmental air catalyst sensor can be quite a headache when it's integrated into the radiator, causing a 2AD8 trouble code. But fear not! URO Parts has a solution with their standalone replacement sensor, making this repair much more manageable and cost-effective.

Key Features:

Guaranteed Fitment: Designed to fit perfectly, ensuring compatibility with your vehicle. Direct OE Replacement: Restores your factory cooling fan sensor's functionality seamlessly. Plug-and-Play Installation: Easy to connect, saving you time and hassle during installation. High-Quality Construction: Crafted from durable materials to withstand the heat of the engine compartment and cooling system. Low Electrical Resistance: Alloy conductors reduce resistance for accurate sensor operation. Reliable and Long-Lasting: Tested for reliability and engineered for a long service life. If you're dealing with a "direct ozone reduction catalyst temperature gradient too low" SES code, upgrading to this high-quality sensor from URO Parts is the solution you need.

The eccentric shaft sensor plays a vital role in controlling valvetronic timing and is often a common issue in BMW vehicles. If you've noticed difficult starts, reduced fuel economy, and overall engine power and performance issues, this component could be the culprit.

Key Features:

Guaranteed Fitment: Designed to fit perfectly, ensuring compatibility with your vehicle. Accurate Positioning: Provides precise shaft position control, even at high RPMs. Direct OE Replacement: Easy to install with its direct-fit design, saving time and effort. Low Electrical Resistance: Alloy connector conductors minimize resistance, ensuring accurate signal transmission. Upgrade to this quality replacement eccentric shaft sensor to restore optimal engine performance and address the symptoms associated with a faulty sensor.

Ensure smooth engine operation in your BMW N62 N73 Engines with this Bremmen Parts Eccentric Shaft Sensor. Designed to detect valve position and lift adjusted by the Valvetronic motor, this sensor prevents poor cold-start issues and rough idle caused by valve lift failure. Avoid potential limp mode situations with this reliable replacement sensor, which also requires a valve cover gasket replacement for proper installation.

Key Benefits:

Detects valve position and lift for optimal engine performance Prevents poor cold-start issues and rough idle Avoids potential limp mode situations Compatible with N62 N73 Engines

Maintain optimal engine performance with this premium replacement knock sensor, engineered to detect pinging, knocking, and pre-detonation within your engine. By precisely monitoring these vibrations, the sensor enables the engine control unit (ECU) to fine-tune ignition timing, safeguarding your engine and enhancing overall efficiency.

A malfunctioning knock sensor can result in diminished power, reduced fuel efficiency, and potential engine damage. Restore your engine's functionality and reliability with this high-quality knock sensor from Bremmen Parts, designed for long-lasting performance and peace of mind.

URO Camshaft Position Sensor - For BMW M52 M54 Engines

URO Camshaft Position Sensor - For BMW M52 M54 Engines is the perfect solution for restoring proper engine operation when your original camshaft position sensor has failed. This direct-fit OE replacement sensor eliminates trouble codes and check engine lights, ensuring smooth engine performance. Made from high-quality polymer and metal materials, this sensor is designed to withstand the intense heat of your BMW’s engine. With alloy conductors that minimize electrical resistance, the sensor provides accurate operation across all engine RPMs. Built for reliability and long-lasting performance, it’s the ideal choice for your BMW M52 or M54 engine.

Key Benefits:

• Direct-fit OE replacement for easy, plug-and-play installation
• Restores proper engine operation by eliminating trouble codes and check engine lights
• High-quality polymer and metal construction withstands the intense heat of the engine
• Alloy conductors minimize electrical resistance for precise operation at any engine RPM
• Engineered for reliability and longevity, providing long-term performance and peace of mind

Upgrade your BMW M52 or M54 engine with the URO Camshaft Position Sensor and enjoy reliable engine performance.

The URO Camshaft Position Sensor is an essential component for BMW engines, providing precise data on camshaft position to ensure accurate fuel injection timing and peak engine performance. Designed to meet OEM specifications, this sensor helps optimize ignition timing, contributing to smoother acceleration, enhanced fuel economy, and overall engine efficiency. Available from Turner Motorsport, the URO Camshaft Position Sensor is the ideal replacement part for BMW owners aiming to maintain optimal performance and reliability.

• Ensures accurate timing for smooth acceleration and responsive power
• Optimizes fuel injection timing, improving fuel efficiency
• Built to OEM standards for precise fit and easy installation in BMW models
• Supports reliable ignition timing for dependable engine operation
• Durable construction withstands high engine temperatures for lasting performance
• Available from Turner Motorsport, a trusted source for BMW replacement parts

The URO Camshaft Position Sensor is a cost-effective solution for BMW owners looking to keep their engine running smoothly and efficiently, delivering the performance and dependability they expect.

Found on the intake air box or throttle body boot, this sensor relays intake air temperature information to the DME. Commonly referred to as the IAT sensor, this component will cause erratic idle, loss of power and a check engine light upon failure. Prevent these issues with this high-quality replacement from URO parts.

URO Parts offers more than 8,000 high-quality spare parts, many of which are specifically designed to replace factory BMW components. Their business was founded on the premise of producing parts that adhere to the highest standards of precision, materials, and workmanship. Each part is closely evaluated by a team of industry professionals to determine how to offer the best blend of durability, function, and price. If you're looking for quality replacement components at a reasonable price, look no further than URO Parts.