Oil Separation & Breather System

When your CPV O-ring fails it causes a slow oil leak on the passenger side of the engine, making an oily mess that frequently resembles a rear main seal leak. Replacing the CPV with an upgraded o-ring ensures a long-term solution to this common problem. 

The factory o-ring over time fails from heat cycling and oil exposure due to the Buna rubber used in OEM o-rings, while the included Viton Fluoroelastomer is resistant to a much higher temperature to ensure prolonged life without leaking. 

After the introduction of the M52TU/M54 engines, BMW observed an uptick in CCV-related issues, especially in cold regions. Vehicles operating in extremely low temperatures often encountered a blockage in the CCV dipstick hose, leading to elevated crankcase pressure and visible blue smoke from the exhaust. To address this issue, BMW introduced cold climate-specific hoses with foam insulation, preventing condensation and facilitating quicker oil warm-up. This kit incorporates top-notch reproduction cold climate hoses to ensure optimal CCV performance across all weather conditions.

The crankcase ventilation valve, known as the oil separator, PCV, CCV, or crankcase pressure regulator valve, plays a vital role in redirecting oil from your vehicle's intake system back into the engine oil pan. This system comprises numerous plastic and rubber hoses, prone to damage due to prolonged exposure to chemicals and heat.

Designed to tackle or prevent impending CCV system failures, this kit includes four foam-insulated hoses made from durable plastic capable of withstanding heat fluctuations and chemical exposure. Additionally, a new ventilation valve is included for a comprehensive and long-lasting repair solution.

Signs indicating the need for crankcase ventilation system replacement include:

Whistling sounds from the intake manifold, caused by crankcase pressure venting through holes in the CCV hoses. Blue smoke emitting from the tailpipe, indicating oil consumption. Excessive oil usage. Milky or yellowish buildup under the oil cap, suggesting condensation due to ventilation valve malfunction. If you're experiencing misfires, lean fuel codes, decreased fuel efficiency, or noticeable oil consumption, it's advisable to overhaul your crankcase ventilation system. Opt for this reliable system from Febi-Bilstein for a repair that meets factory standards and ensures consistent performance.

Rein Crank Case Vent Hose is a high-quality replacement part designed to enhance the performance and longevity of your vehicle’s engine. Manufactured by Rein Automotive, this vent hose is built to withstand high pressures and temperatures, ensuring reliable crankcase ventilation. Engineered for a precise fit, it helps prevent harmful oil vapors from entering the intake manifold, improving overall engine efficiency. Available at Turner Motorsport, this vent hose is an ideal choice for drivers looking to maintain their vehicle’s performance and emissions standards.

• Designed for optimal crankcase ventilation, improving engine performance
• Reduces oil vapor contamination in the intake system, protecting engine components
• Made with durable materials to resist wear from heat and pressure
• Ensures precise fit and easy installation as a direct OEM replacement
• Helps reduce harmful emissions, supporting cleaner engine operation

Turner Motorsport offers the Rein Crank Case Vent Hose as a dependable solution to keep your engine running smoothly while meeting emissions regulations.

Elevate your S63 4.4L engine's capabilities with our meticulously designed Crank Case Vent Hose Kit. Crafted from premium-grade materials, this kit ensures superior ventilation, mitigating pressure accumulation within the engine, thereby enhancing its overall performance.

Engineered to precise specifications, our kit seamlessly replaces the OEM vent hoses, guaranteeing a perfect fit. By reducing stress on the engine, it prolongs its lifespan and maintains peak functionality. Rely on this kit to provide unparalleled performance and unwavering reliability for your S63 4.4L engine.

BMW Oil Separator Valve | M60 3.0 / 4.0L is a vital component that ensures proper crankcase ventilation by separating oil vapors from blow-by gases, preventing excessive oil consumption and maintaining engine efficiency. Designed for BMW models equipped with the M60 3.0L and 4.0L engines, this oil separator valve helps reduce carbon buildup and extends the life of essential engine components. For optimal results, it is recommended to replace the valve cover and crankcase ventilation system (CCV) when changing the separator valve.

• Effectively separates oil vapors to prevent excessive oil consumption
• Helps maintain proper crankcase ventilation for optimal engine performance
• Reduces carbon buildup and prolongs engine longevity
• Direct-fit replacement for BMW M60 3.0L and 4.0L engines
• High-quality materials ensure durability and resistance to engine heat
• Recommended to replace valve cover and CCV for complete system maintenance

Ensure the longevity and efficiency of your BMW engine by replacing a worn oil separator valve with this high-quality replacement.

BMW N63 4.4L Vent Pipe

The BMW N63 4.4L Vent Pipe addresses common issues with oil separators freezing in cold weather conditions. This problem often occurs if the vehicle is driven before it is fully warmed up, leading to a howling noise and multiple oil leaks. The crankcase breather valve in the vent pipe purges oil vapor from the engine block into the valve cover. However, condensation can sometimes cause the valve to freeze, which may result in the oil separator system failing, cracking, or disintegrating. This replacement vent pipe ensures proper function and prevents costly damage by maintaining the integrity of the oil separator system.

Benefits:

• Prevents Freezing Issues: Reduces the risk of oil separator failure in cold weather conditions.
• Eliminates Oil Leaks: Helps prevent leaks caused by frozen oil separators.
• Ensures Proper Ventilation: Maintains effective purging of oil vapor from the engine block.
• Durable Construction: Built to withstand harsh weather conditions and engine stress.
• Direct Replacement: Designed to fit seamlessly with BMW N63 4.4L engines.

Upgrade your N14 N18 1.6L Engine with the Vent Hose. This hose connects to the top valve cover with a special hose clip end and extends to the bottom side of the intake manifold, ensuring optimal performance of your Mini. It's a crucial component of the intake system, designed to enhance engine efficiency and longevity.

• Ensures proper ventilation of the engine
• Connects securely to the valve cover and intake manifold
• Facilitates efficient airflow within the engine compartment
• Compatible with N14 N18 1.6L Engine models
• Easy to install and replace as needed

The engine crankcase breather hose is a vital part of the Positive Crankcase Ventilation (PCV) system, responsible for directing pressurized air from the engine crankcase to the air/oil separator, also known as the PCV valve. This separator removes oil vapors from the air, allowing the oil to return to the engine while feeding the filtered air back into the intake system to support efficient combustion.

As a byproduct of the combustion process, positive crankcase pressure naturally builds up in the engine. The breather hose operates under constant exposure to heat, pressure, and an air/oil vapor mixture, making it prone to wear and failure over time. Ensuring the breather hose is in proper working condition is crucial for maintaining engine performance, adhering to emissions standards, and preserving the functionality of the PCV system. Promptly replace this component at the first signs of damage or degradation to avoid further complications.

The plastic hoses and oil separator can crack or become faulty, leading to vacuum leaks or oil leaks. This is caused by the stress the plastic components are exposed to during heating and cooling cycles, especially if the vehicle is not brought up to operating temperature during driving in cold weather climates.

This kit includes the needed hoses, oil separator, mounting grommet, and hardware.

Fits the following BMWs:
2000-2003 E39 BMW 530i