The N54/N55 are the powerhouses of BMW, one of the most common tuning platforms, and a fan favorite for spirited driving. Being an N54/N55 owner you know that oil temps can get out of hand leaving you with an anxious feeling and the needle a little too close to the red on your gauge cluster. What if you could get the oil flowing faster, maintain lower temperatures, and still have proper engine warm-up?

Upgrade your N54/N55 engine with our Billet oil cooler housing, replacing the underperforming factory-cast aluminum unit. Engineered for enhanced performance and a blended aesthetic, our Turner oil cooler housing features an OEM+ black anodized finish and our own engineered lower-temperature thermostat. Unlike makeshift solutions like thermostat bypass kits, our housing integrates an OE thermostat, ensuring a gradual yet expedited engine warm-up process, similar to factory settings but faster.

Out goes the factory 110-degree Celsius (230F) thermostat, replaced by our 70-degree Celsius (158F) counterpart. This new thermostat triggers oil flow a significant 72 degrees Fahrenheit earlier than the factory version. This early flow translates into prolonged lower oil temperatures for both the oil cooler and engine, maintaining a happier, healthier engine with consistently lower operating temperatures.

For N54 owners seeking to use the full potential of their tuned or modified engines, our upgraded housing and thermostat are must-have additions, especially for those who frequent the track or enjoy spirited drives on winding roads. Even if you're not pushing your motor to its limits, this upgrade significantly enhances reliability. With rising oil temperatures, the risk of oil breakdown rises, resulting in compromised lubrication, more engine deposits, and increased wear over time. Our solution addresses these concerns, protecting your engine's longevity and performance, regardless of your driving style.

For vehicles equipped with the factory oil cooler, our housing offers a multitude of advantages and is a direct replacement for the OEM unit. If your vehicle lacks a factory oil cooler, this presents an ideal chance to upgrade your setup with our housing, enabling the addition of a factory cooler for enhanced performance and increased reliability. Our primary objective is to maintain optimal oil temperatures, ensuring proper lubrication for the engine's internal components, in turn prolonging their lifespan.

Features:

Thermostat - 40 degrees Celsius/ 72 degrees Fahrenheit lower than the factory unit Billet aluminum to replace the raw cast aluminum factory housing Optional cooler capability for cars without an OEM oil cooler Utilizes the lower temp thermostat to circulate oil sooner rather than an always open solution which inhibits warm-up Combine with OEM oil cooler to add cooling capacity to your FBO N54/N55 or replace the stock housing for a cooling upgrade using your existing cooler Replaceable thermostat and gaskets for easy maintenance Quick easy installation Kit Contents:

N54/N55 Billet Thermostat Housing Billet thermostat cover Low-temp thermostat Thermostat spring Housing and thermostat cover gaskets 2 Oil cooler line O-rings (17222245358) Product Development:

Our upgraded oil cooler housing was designed, engineered, tested, and quality inspected by our Research and Development team at Turner. Nothing but the highest level of precision and quality through leading-edge product development technology including FARO laser scanning for reverse engineering and quality inspection, SolidWorks 3D CAD modeling, rapid prototyping utilizing our in-house 3D printer, and rigorous long-term product testing.

When we designed this catch we wanted to have the most function options available, the best separation method, and the easiest to service. The Turner engineered catch cans offer a pre-setup design based ion desired flow direction, however this does not limit you to this flow. The inner baffle orientation can be easily adjusted to flow in both directions in case you decide to move this catch can to a different vehicle. A 4 chamber system  baffle system inside the catch can was engineered to create multiple changes in the direction of airflow within the separator to cause oil droplets to fall out of suspension before exiting the catch can. Having a closed / recirculated design reduces oil ingestion and promotes cleaner emissions and odor-less operation.

Our catch can was also designed with the idea that the cans fill level can easily be checked with a top mounted dipstick and an optional use bottom drain hole. The drain system comes complete with a valve and hose to be mounted at a lower area of the vehicle so when you're doing an oil change you can drain the catch can.

Features:

• 6061-T6 billet machined body, anodized black for lasting protection and appearance
• Strategically positioned 4 chamber baffle system maximizes oil / air separation 
• Knurled and black anodized oil dipstick makes inspecting oil volume of reservoir clean and simple
• Sealed with a pre-installed viton O-Ring
• Includes 2.5mm allen key to remove baffle plates for cleaning
• Engineered to create multiple changes in the direction of airflow within the separator to cause oil droplets to fall out of suspension before exiting the catch can
• Closed / recirculated design reduces oil ingestion and promotes cleaner emissions and odor-less operation
• Optional use drain hole - drain kit included!
• Universal mounting kit

When we designed this catch we wanted to have the most function options available, the best separation method, and the easiest to service. The Turner engineered catch cans offer a pre-setup design based ion desired flow direction, however this does not limit you to this flow. The inner baffle orientation can be easily adjusted to flow in both directions in case you decide to move this catch can to a different vehicle. A 4 chamber system  baffle system inside the catch can was engineered to create multiple changes in the direction of airflow within the separator to cause oil droplets to fall out of suspension before exiting the catch can. Having a closed / recirculated design reduces oil ingestion and promotes cleaner emissions and odor-less operation.

Our catch can was also designed with the idea that the cans fill level can easily be checked with a top mounted dipstick and an optional use bottom drain hole. The drain hole can be used with a valve and hose to be mounted at a lower area of the vehicle so when you're doing an oil change you can drain the catch can.

Features:

• 6061-T6 billet machined body, anodized black for lasting protection and appearance
• Strategically positioned 4 chamber baffle system maximizes oil / air separation 
• Knurled and black anodized oil dipstick makes inspecting oil volume of reservoir clean and simple
• Sealed with a pre-installed viton O-Ring
• Includes 2.5mm allen key to remove baffle plates for cleaning
• Engineered to create multiple changes in the direction of airflow within the separator to cause oil droplets to fall out of suspension before exiting the catch can
• Closed / recirculated design reduces oil ingestion and promotes cleaner emissions and odor-less operation
• Optional use drain hole (valve and hose sold separately, watch for our model specific drain kits!)

Upgrade your MINI with the M7 Oil Catch Can Kit__xxSTARTxx__/h1

The newly updated R55 through R57 Oil Catch Can kit for MINIs equipped with the N14 engine comes with a "designed-to-fit" stainless steel bracket, mounting hardware and pre-assembled hoses. Installation is super easy...no drilling and no special tools are needed. NOTE: This kit has been redesigned to fit on the firewall directly behind the outlet of the airbox. It uses the factory tab located on the firewall."Forum experts and social hysteria" say an OCC is not needed but we beg to differ. Why do so many MINI owners suffer from carbon buildup on their intake valve? The answer is oil being recycled through the intake tract to be burned. With the M7 Oil Catch Can, your MINI Cooper's engine will be protected from excessive oil and hydrocarbon buildup which leads to performance-hindering oil film and sludge along your intake tract, on your engine control sensors and on your engine's intake valves. Because the 2007 & up MINI is direct injection the intake valves do not benefit from the cleaning action provided by the gasoline as in older port injection engines. Now all the oil blow-by burns onto the intake valves and builds up into a flow choking hydrocarbon mess. The end result is loss of power and a very expensive repair bill. This oil film & sludge can appear in other critical places throughout the engine-- such as the intercooler-- where clean surfaces are critical for maximized heat transfer and on your MAF sensor (Mass Air Flow) where the film will cause the sensor to send a false signal to your ECU killing performance.

By capturing excess oil vapor and particles, the M7 Oil Catch Can ensures that oil film and sludge will not become a factor in your vehicle's performance. If you don't think your engine is pumping oil back through your intake system, remove the breather tube and look at all the oil!. The breather tube connects directly to you intake hose and directs this oily mess back through your engine to be burned.

Now with our exclusive "Exact-Fit" pre-assembled hose kit and brackets installation is super-easy.

Features:

• Pre-assembled hose assemblies.
• Stainless steel bracket and mounting hardware
• Eliminate intake tract oil contamination and intake valve damage.
• Prevent pre-mature sensor failure
• Keep engine performance at peak levels
• Billet Aluminum Construction
• Bright Black Anodized Finish
• Laser Etched M7 Logo

The M7 Oil Catch Can is not only functional is a work of automotive performance ART! It is CNC machined from billet aluminum and adds a sharp look to your engine compartment.

All hoses, brackets, clamps, necessary fittings and easy to follow detailed step-by-step instructions are available on this page in .PDF format. The design includes an oil drain plug and an easy to view sight tube which indicated the oil level within the can. The hoses are high quality "Made in the USA" automotive grade designed to withstand the rigors of the under-hood environment and to not degrade when exposed to oil. Beware of other "low cost" catch can systems that use silicone hoses because oil and silicone are not compatible. Silicone hoses will will eventually deteriorate and make an absolute mess of your engine compartment.

This oil filter housing cap is constructed from high-quality billet aluminum, complete with a black anodized finish for added corrosion resistance. Designed specifically for the S54, this lid replaces the OE part and accepts the OE o-ring.

This part features two 1/8-27 NPT holes that can be used to incorporate oil temperature and oil pressure sensors. Port plugs are included to block off the ports if they are not being used.

Machined with care in-house at VAC Motorsports for perfect fitment, these lids are a perfect replacement for enthusiasts looking to seamlessly integrate oil temperature and pressure sensors without tapping into their oil pan.

Ensure a secure oil change for your MINI with this essential Oil Drain Plug. Designed for a snug fit with the copper washer, it guarantees a tight seal, making it an ideal replacement during oil changes.

• Compatible with MINI vehicles
• Features an 8mm allen wrench for easy removal
• Includes drain plug gasket for added convenience