These adjustable rear links are only required when using sway bar / swaybars with a suspension with a very low ride height, where it may be necessary to adjust the length of the end links for proper sway bar clearance from the drive axles or other suspension components. These suspensions are usually found only on race cars but this may also apply to street cars with sport springs/sport coil overs that are lowered a lot. On most street cars lowered 1.5" or less, the stock links will be fine.

These end links feature a Heim joint, which allows enough lateral movement when disconnected to adjust the length of the link without removing the entire link from the car. This is particularly helpful when eliminating or adjusting preload while tuning the suspension. Similar links without this joint, can't be adjusted without totally removing the link from the car.

Built-in grease fittings allow for occasional lube, and a packet of grease is included. These links are sold as a set, and include two end links and hardware for H&R and TMS sway bars (other brands may not need the hardware). 

At their shortest setting they are 2.875" hole to hole and on their longest setting they are 3.5" hole to hole.

*Note: these links will not work with factory or non-adjustable Eibach sway bars.

For use with 22.5mm CSL rear sway bar, you will need 2 of these.

Genuine BMW Stabilizer Rubber Mounting - D=22,5mm
This item fits the following BMW Chassis:
E86
 

Sway bar bushings tend to split over time, failing to properly secure and reinforce the sway bar. If yours has begun to split or if your vehicle is more than 5 years old, it is a good idea to replace them to ensure proper sway bar operation.

Genuine BMW Stabilizer Rubber Mounting - D=14Mm
This item fits the following BMW Chassis:
F06,F10,F13

Lowering your BMW does wonders for appearance and handling, but it also changes suspension geometry in ways that can hurt performance. As ride height changes, angles between the sway bar, control arms, and axles shift, which can cause binding, poor fitment, and added stress on the factory fixed-length end links. This is especially noticeable on cars equipped with coilover suspension, where slight height differences side to side can preload the sway bar and lead to inconsistent handling.

Our team of dedicated BMW enthusiasts set out to address this common issue with Adjustable Rear Sway Bar End Links. Designed with performance in mind, they offer a fully adjustable range from 100mm to 120mm, helping eliminate preload, restore proper suspension alignment, and improve overall sway bar function. Constructed from high-quality billet aluminum, these end links are built to outlast the factory cast components and are finished with a black anodized coating for excellent corrosion resistance. Laser-etched wrench size markings allow for quick, easy adjustments while installed on the vehicle. Unlike the factory design, these end links use spherical rod ends at the control arm for increased responsiveness and a more direct handling feel. These end links feature a bolt-through bushing design, which is compatible with most adjustable aftermarket sway bars. Mounting hardware is included for easy installation.

Features & Benefits:

Adjustable from 100mm to 120mm Strong 6061-T6 billet aluminum construction Black anodized finish resists corrosion Spherical rod ends improve response and handling feel Polyurethane bushing with knurled bore helps retain grease Fits most aftermarket sway bars with bolt-through attachment Laser-etched markings for quick and easy adjustments

Lowering your BMW does wonders for appearance and handling, but it also changes suspension geometry in ways that can hurt performance. As ride height changes, angles between the sway bar, control arms, and axles shift, which can cause binding, poor fitment, and added stress on the factory fixed-length end links. This is especially noticeable on cars equipped with coilover suspension, where slight height differences side to side can preload the sway bar and lead to inconsistent handling.

Our team of dedicated BMW enthusiasts set out to remedy this common issue with a set of Adjustable Rear Sway Bar End Links. Designed with performance in mind, they offer a fully adjustable range from 100mm to 120mm, helping eliminate preload, restore proper suspension alignment, and improve overall sway bar function. Constructed from high-quality billet aluminum, these end links are built to outlast the factory cast components and are finished with a black anodized coating for excellent corrosion resistance. Laser-etched wrench size markings allow for quick, easy adjustments while installed on the vehicle. Unlike the factory design, these end links use spherical rod ends at the control arm for increased responsiveness and a more direct handling feel. A unique knurled bushing design also ensures compatibility with the OEM sway bar, offering a first-to-market solution for enthusiasts looking to retain factory components.

Features & Benefits:

Adjustable from 100mm to 120mm Strong 6061-T6 billet aluminum construction Black anodized finish resists corrosion Spherical rod ends improve response and handling feel Polyurethane bushing with knurled bore helps retain grease Fits factory rear sway bars on E23, E24, E28, E30, and E36 Laser-etched markings for quick and easy adjustments

Sway bar end links connect the swaybar to the rest of the suspension, preventing body roll and keeping everything in line in tight turns. This exposes these links to a high amount of stress and pressure, often leading to split bushings and sloppy body control and knocking noises. Meyle sway bar links are the perfect option to restore body control and eliminate knocking noises.

As a leading source of high-performance BMW parts and accessories since 1993, we at Turner Motorsport are honored to be the go-to supplier for tens of thousands of enthusiasts the world over. With over two decades of parts, service, and racing experience under our belt, we provide only quality performance and replacement parts. All of our performance parts are those we would (and do!) install and run on our own cars, as well as replacement parts that are Genuine BMW or from OEM manufacturers. We only offer parts we know you can trust to perform!

This stock replacement sway bar / swaybar link secures the rear sway bar ends to the chassis. Over time the rubber breaks down and can cause poor handling. Alternate part number 33551124375.

This item fits the following BMWs:
1984-1991 E30 BMW 318i 318is 318ic 325e 325es 325i 325ic 325is 325ix M3
1992-1998 E36 BMW 318i 318is 318ic 323is 323ic 325i 325is 325ic 328i 328is 328ic M3
1982-1988 E28 BMW 524td 528e 533i 535i 535is M5
1983-1989 E24 BMW 633csi 635csi M6
1982-1987 E23 BMW 733i 735i

MAXX-G Adjustable Suspension Links, designed to add bind-free travel and straightforward camber adjustments to the rear suspension of any MINI. These links feature a solid aluminum 1" hex adjuster sleeve with opposing 3/4" left-hand and right-hand threads at each end, allowing effortless camber adjustment. The exclusive Hybrid Polymer MonoBall (HPMB) link end, a groundbreaking design in the industry, combines the benefits of a rod end for suspension movement with the vibration isolation and durability of a urethane bushing.

PRODUCT BENEFITS:

• Enhances cornering performance and suspension alignment
• Industry-first "Hybrid Polymer MonoBall" (HPMB) link ends
• Combines advantages of monoball rod ends and urethane bushings
• Offers bind-free high angular misalignment with noise-free operation
• Forged alloy steel main housing with a sealed polymer race for vibration dampening
• Serviceable, rebuildable, and greasable
• Military-grade 6061-T6 aluminum adjuster sleeve for easy length adjustments
• Made in the USA & GUARANTEED for LIFE!

Enhance your Mini's performance and cornering capabilities with M7 MAXX-G Adjustable Swaybar Endlinks. Designed for both lowered and raised Minis, these endlinks offer numerous benefits including symmetric cornering performance, bind-free suspension travel, better suspension alignment, and overall chassis balance. The forged and heat-treated alloy steel housings with sealed ball stud and socket design ensure durability and reliability even during aggressive driving. The adjustable length allows for precise chassis tuning and optimal grip and balance. Made in the USA, these endlinks are a must-have upgrade for any Mini enthusiast.

• Improves symmetric cornering performance
• Provides bind-free suspension travel
• Enhances suspension alignment and chassis balance
• Features forged alloy steel construction for strength and durability
• Adjustable length for precise chassis tuning
• Easy to install and adjust with simple hand tools

Upgrade your Mini's suspension with M7 MAXX-G Adjustable Swaybar Endlinks for optimal performance on the road or track.