ECS BMW Suspension Parts

Elevate Your BMW's Performance with ECS Tuning's Ultimate Performance Rear Shock Mount Kit

ECS Tuning presents the Ultimate Performance Rear Shock Mount Kit, specifically designed to address recurring rear shock mount blowouts experienced by various BMW models, including the M3 and non-M 3 Series dating back to the E30 chassis in 1984. This innovative kit provides a long-term solution, ensuring optimal damper performance and longevity while eliminating rear clunking noises and handling issues caused by blown shock mounts.

Key Benefits:

• Solves rear shock mount blowout issues on BMW models
• Allows full articulation of rear dampers for improved performance
• Industry-first design with PTFE lined stainless steel monoball spherical bearing
• 80A polyurethane isolation bushings reduce noise, vibration, and harshness (NVH)
• Lower dust seal enhances bearing life by preventing road debris ingress
• Corrosion-resistant anodized 6061-T6 construction for durability
• Compatible with 10mm, 12mm, or 14mm damper shafts

Upgrade your BMW's rear shock mounts with ECS Tuning's Ultimate Performance Rear Shock Mount Kit, providing superior performance, reduced NVH, and increased bearing longevity for a more controlled and comfortable ride.

Due to their soft rubber construction, OE strut mounts are known to wear at an accelerated rate. Many high-mileage vehicles fall victim to strut mount failure, which is commonly associated with annoying clunks, groans, or rattles from the front suspension.

With this issue in mind, ECS Tuning developed their heavy-duty front strut mount with upgraded, higher durometer rubber to resolve sloppy handling and increase longevity. Manufactured precisely within OEM tolerances, these mounts are a perfect fit for your BMW.

Features:

Reduces deflection: Increases vehicle handling and cornering dynamics by removing deflection within the strut mount. Increases longevity: Upgraded rubber construction makes for a stiffer mount, less prone to cracking and general degradation. Developed in-house: Designed and tested by ECS Tuning engineers, this mount is sure to outlast an OE replacement. Upgrade to a better strut mount without sacrificing ride comfort! Improve longevity and ride control all at once.

To reduce the understeering affects of a staggered wheel setup you want a balanced set of sway bars. ECS has configured this anti-roll bar set for the non-M E46 with a 27mm adjustable front bar and a 21mm rear bar. The front is adjustable to two positions to fine-tune the handling and reduce understeer. The rear bar is fixed to retain the stock sway bar link. These anti-roll bars include urethane bushings with a reinforced inner liner that eliminates squeaks and doesn't require lubrication. The bars are powder coated for durability and good looks.

These bars fit in the stock locations using the existing brackets and links. Adjustable links are not required but recommended if the car is lowered or if you have coil overs (note: the rear bar is designed to only use the stock link, heavily lowered cars should not use this kit).

The bars are adjustable so any driver can find an ideal setup for the type of driving they are doing. The sway bar becomes stiffer in the hole(s) furthest from the end of the bar. The holes at the very end of the bar are the softest setting. We would generally recommend starting out with the front bar set to the stiffer setting and adjust to your liking from there. 

This item fits the following BMWs: 
1999-2006 E46 BMW 323i 323ci 325i 325ci 328i 328ci 330i 330ci

Want a race-spec rear shock mount but with the comfort of a factory bushing? This ECS rear shock mount combines the precision and articulation of a spherical bearing with the isolation of urethane bushings. The stainless monoball bearing is lined with PTFE lubricant and suspended in 80A urethane and housed in a hard anodized 6061-T6 aluminum mount. The spherical bearing is a better design than most rear shock mounts because it allows the shock to move and tilt without side-loading the shock shaft (which leads to premature failure of the shock). Most Genuine BMW and aftermarket shock mounts are not designed for shock angles and the stress that track or performance driving will put on the shock shaft. The ECS shock mount is properly designed to handle these loads. The internal bearing is also replaceable - it will be years before you have to replace the entire mount. The ECS mount is fully encapsulated to prevent the common shock mount failure of the stock mount design.

ECS RSM features:

• Maintenance free, PTFE lined, stainless steel monoball spherical bearing for full shaft articulation
• 80A polyurethane isolation bushings for NVH control
• Accommodates 10mm, 12mm, or 14mm damper shafts
• Fully constrained shaft mount makes RSM blow out impossible
• Hard anodized 6061-T6 construction
• Fully rebuildable design

* - the RSM comes with the BMW standard 10mm shock shaft bushings. 12mm is used on some performance shocks and 14mm is used on some true motorsport rear shocks.