Ohlins Racing has a long history dating back to 1976 of providing premium motorcycle and automotive suspension systems to numerous racing teams, individual racers, and OE brands such as BMW Motorsport, Audi, Lamborghini. Pagani, Ducati and Kawasaki. Over time, thanks to extensive R&D, testing, and tuning, their products have evolved into some of the highest quality suspension systems in the world, providing years of flawless operation on both the street and the track.

Ohlins' latest automotive suspension system, the DFV (Dual Flow Valve) Road and Track Coilover Kit, has bridged the gap between comfortable stock suspension and track focused coilover kits. These kits provide a ride that glides over typical bumps and dips in the road, all without the typical hard rattle and harsh feel of usual coilovers, and turn in tight and maintain tire grip and traction in corners significantly better than stock suspension ever could. This is all thanks to the spring rate chosen and Ohlins and their signature Dual Flow Valve. The DFV maintains comfort and agility by giving the same characteristics for both rebound and compression, allowing the wheel and tire to maintain constant contact with the road/track for maximum control.

The Dual Flow Valve works by controlling shock fluid flow based on resistance and impact velocity. This is controlled in both compression and rebound, giving the quick shock operation that helps maintain traction. At low shaft travel speeds, oil flows mostly through the shaft jet bleed. At higher shaft speeds, oil flows mostly through the compression/rebound ports in the piston. At very high shaft speeds, or during sudden accelerations from potholes or large bumps in the road, oil can then escape through the ports in the DFV, absorbing a large amount of energy that would otherwise throw off the balance and control of the vehicle and keeping the tire planted firmly on the ground. With all three compression and rebound ports working together according to pressure and shaft speed, the result is the notorious premium suspension feel that only Ohlins can offer.

In addition to managing the rebound and compression control, coilovers must also properly address heat changes in the shock oil. As the shock is pushed harder and longer, the oil quickly heats up due to friction and compression, and the oils flow characteristics change. The hotter the oil is, the easier it is for it to travel through ports and valves. To prevent this typical fade in control, Ohlins has implemented a temperature controlled needle bleed valve system that will expand as temperatures rise, slowly increasing restriction in the fluids flow through the valve gap. This produces a consistent dampening rate that maintains the vehicle's suspension characteristics lap after lap, turn after turn, no matter how hard you push your suspension's capabilities.

Features:

• DFV (Dual Flow Valve)
• Adjustable ride-height
• Fully rebuildable
• Corrosion salt spray tested (ISO 9227)
• Includes hardware and installation instructions
• 2 year Limited Warranty

Specs:

• Front Spring Rating: 343 lbs/in  ( 6 kg/mm)
• Rear Spring Rating: 686 lbs/in  ( 12 kg/mm)

*Now available are optional EDC Cancellation Modules that will prevent any lights or issues with suspension control systems. Turner Motorsport recommends purchasing these in addition to the suspension kit to get the most out of your Ohlins suspension system.

Find installation instructions HERE.
Find owner's manual HERE.

Fits the following BMWs:
2008-2013 E9X BMW M3

Established in 1976, Ohlins Suspension stands as a prestigious brand, collaborating with notable OE suppliers like BMW Motorsport, Audi, Lamborghini, Pagani, Ducati, and Kawasaki. The DFV Road and Track Coilover Kit by Ohlins integrates state-of-the-art Dual Flow Valve (DFV) technology, setting itself apart in the market for exceptional traction, grip, and handling.

The DFV technology ensures consistent rebound and compression characteristics, swiftly realigning wheels and tires on the road. Offering a balance between comfort and agility, these coilovers maintain an OE suspension feel at lower speeds and deliver precise control at higher speeds or on uneven terrain.

Temperature management is critical for shock oil performance. Ohlins employs a unique needle bleed valve system that reacts to temperature changes, ensuring consistent damping rates regardless of temperature fluctuations, guaranteeing reliable performance.

Key Features:

• Lightweight aluminum construction
• Long-term corrosion resistance
• 30-level 1-way adjustable dampening
• OE fitment using stock vehicle upper mounts location
• Rebuildable design
• Threaded shock body for height adjustment
• Adjustable spring preload for customization
• Monotube damper construction
• 2-year limited warranty
• Approximately 15mm lower than stock
• ECS Insider Tip: Adjust suspension valves for hardness or softness as needed.

Looking to stiffen up your rear shock mount without going for a solid rear mount? The Polyurethane Rear Performance Strut Mount from IRP will give you the stiffer reinforcement without giving you the typical noise, vibration, and harshness that come with traditional performance strut mounts. The polyurethane also helps with preventing rear shock blowouts, a common problem for stock BMW rear mounts that are paired with stiffer than stock suspension. 

The bearing sleeve and poly bushing are built to work with all stock style shocks such as Bilstein and H&R coilover and suspension kits.

Fits the following BMW chassis:
E36 BMW All Submodels except for 318ti
E46 BMW All Submodels
E30 BMW All Submodels
E36 Z3 BMW All Submodels
E85/E86 Z4 BMW All Submodels

If you are concerned about strut tower mushrooming and looking for improved handling, the M7 Strut Tower Brace (STB) is the solution. This is the ONLY strut tower brace on the market that features anti-mushrooming technology.

Repeatedly, we've heard the same complaint: strut towers mushroom after heavy impacts from shocks and low aspect ratio tires. Initially, the shock towers take on a barely visible convex shape, but if compared to the original sheet metal, you'll find the horizontal plane has moved as much as 3/8" upwards, making alignment nearly impossible.

This issue often shows up as a slight pull to the left or right, depending on which strut tower is affected. The M7 Strut Tower Brace's end mounting plates solve this problem by sandwiching the sheet metal and shock top plate, creating a reinforced surface that won't bend, even during hard impacts.

The M7 STB features 1/2" (13mm) thick end plates that add extra strength to the strut towers, preventing mushrooming and potentially costly repairs. The cross brace significantly improves handling by adding torsional stiffness to the front body structure, helping keep your tires planted and pointed in the direction you want to go, especially during hard turns. Machined from billet aluminum and matte black powder coated, the M7 Strut Tower Brace boasts a durable black finish that looks great and won't chip or oxidize.

We have customers who won't drive their new MINI off the lot without one and dealers that sell every new MINI with either the M7 Strut Reinforcement Plates or the M7 Strut Tower Brace.

Concerned about clearance? No worries. The M7 STB profile is designed to clear both stock and aftermarket cold air intakes and ECUs. Its modular design allows easy access to the oil filter or any other accessories that might normally be blocked and require removal of the entire brace.

Installation is a snap (often taking less than 20 minutes)! No need for new nuts—the brace uses the three stock nuts on each side. Installation instructions are available online by clicking the "INSTALLATION" link on this page.

The M7 Strut Reinforcement Plates and the M7 Strut Tower Brace are two separate products that address strut tower mushrooming (you only need one or the other).

If your MINI is mainly a daily driver, the M7 Strut Reinforcement Plates are sufficient. If you have performance driving in mind, the M7 Strut Tower Brace is what you're looking for!

Please note:

• You cannot buy the SRPs and attach the cross-bar at a later time.
• The brace does not directly fit on the R50 and R52 Non-"S" Cooper due to limited hood clearance of the non-supercharged cars. It will fit but may push up on the hood slightly, requiring molding or cutting of the hood insulation after installation.
• Trimming of the underhood insulation material may be required to fully clear this brace. This is a very tight space.

**For vehicles with coilover front suspension**

When looking to dial in your steering geometry and alignment for reduced tire where and/or better track handling, the stock suspension is quite limited. To fix this, you can install Camber/Caster plates such as these plates from IRP. Camber/Caster plates allow for adjustment of the top position of the shock's mounting position. These slight adjustments have a huge impact on the stance of the of the wheel when driving straight down the road and when turning into a corner. With simple adjustments, you can increase the grip of the tires in hard turns, improve tread life, or even just make an alignment correction for a vehicle with a lowered ride height. 

The IRP Camber Caster plates are made of an aircraft grade aluminum body, for strength and low weight, with an adjustable mounting plate that utilizes a steel monoball mounting point. This makes the plate resistant to corrosion and prevents deformation even with the stiffest shocks and springs.

Features:

• Decreased understeer
• Decreases outside edge tire wear
• Aircraft Grade Aluminum Construction
• Steel Monoball and Mounting Sleeves

Fits the following BMWs:
1999-2006 E46 BMW

The front control arm bushings is the Achilles heel on the E39 models. The original factory bushings are fluid filled and rely on the fluid to absorb vibration and resist deflection. When the fluid is gone the rubber left over cannot match the original bushing's strength. The left over rubber is not stiff enough to resist the movements from the suspension. The result is a lot of vibration and reduced feedback and response from the steering.

Meyle has addressed this issue with bushings that are not fluid-filled. The bushing is made of solid rubber that will last longer than the original bushing and is a bit stiffer than new originals for better response and feel. The lack of play from the solid rubber design will mean sharper steering, restoring much of the car's precision and 'connected' feel.

This is a package of Meyle HD control arms with the HD bushings already pressed in. This makes for an easy swap out-swap in install. These arms replace the existing stock upper control arms - otherwise known as a tension strut or strut support arm. It's the arm with the twist. The BMW part numbers for these arms are 31 12 1 141 717 and 31 12 1 141 718.

Meyle is a German brand in business since 1958 and all of their products are TUV approved and meet or exceed ISO standards. All Meyle HD parts come with a 4-year, unlimited mileage warranty.

Features:

• 4 Year Warranty

• All metal ball joints are more reliable and longer lasting than stock

• Bushings are solid rubber rather than fluid filled, providing longevity and handling feel improvements

This item fits the following BMWs:
1997-2003 E39 5 Series BMW 525i, 525iT, 528i, 528iT, 530i sedans and touring wagons
2000-2003 E52 Z8 Z8 - Z8 Alpina

**For vehicles with stock style springs**

When looking to dial in your steering geometry and alignment for reduced tire where and/or better track handling, the stock suspension is quite limited. To fix this, you can install Camber/Caster plates such as these plates from IRP. Camber/Caster plates allow for adjustment of the top position of the shock's mounting position. These slight adjustments have a huge impact on the stance of the of the wheel when driving straight down the road and when turning into a corner. With simple adjustments, you can increase the grip of the tires in hard turns, improve tread life, or even just make an alignment correction for a vehicle with a lowered ride height. 

The IRP Camber Caster plates are made of an aircraft grade aluminum body, for strength and low weight, with an adjustable mounting plate that utilizes a steel monoball mounting point. This makes the plate resistant to corrosion and prevents deformation even with the stiffest shocks and springs.

Features:

• Decreased understeer
• Decreases outside edge tire wear
• Aircraft Grade Aluminum Construction
• Steel Monoball and Mounting Sleeves

Fits the following BMWs:
1999-2006 E46 BMW

A strut tower brace adds additional reinforcement to the front strut towers, tying them together for extra rigidity. This makes the whole structure stronger with less chassis flex. Handling and steering feel are improved with better turn-in and input with no downsides. 

The IRP adjustable strut brace bar is a high quality brace that is constructed of 100% steel for guaranteed reinforcement and prevention of flex. The brace bar is painted black to ensure corrosion protection and to add to the looks of the engine bay.

Easily installed with basic hand tools.

Fits the following BMW chassis:
E34 BMW All Submodels

Looking to upgrade your front suspension to increase the strength and your steering angle for the track? IRP has you covered with their BMW Lock Kit. This kit includes new control arms that are stronger than stock and have monoball ball joints, new tie rod ends that feature steel monoball ball joints as well, new offset control arm bushings, fully adjustable camber plates, roll center/bump steer correction plates, and all new hardware. This enables this kit to be fully plug and play, giving you a much more adjustable front suspension, and increases the total amount of steering angle up to 65 degrees.

This kit is perfect for those looking to build a drift car and ensure their suspension is ready to take on the challenge.

Kit features:

• CNC Laser Cut Components
• Plug & Play - includes all needed hardware
• Increase to 65 Degree (or more) steering angle
• Includes Camber Plates
• Stiffer offset control arm bushings
• Roll Center and Bump Steer Correction Plates
• High strength control arms with steel monoball ball joints
• Increased length steering tie rods with steel monoball ball joints
• DriftAllstar- & EEDC-Tested
• Total weight of all components included: 13.5 kg / 29.8 lbs

Fits the following BMWs:
1999-2006 E46 BMW All Non-M RWD Submodels

A strut tower brace adds additional reinforcement to the front strut towers, tying them together for extra rigidity. This makes the whole structure stronger with less chassis flex. Handling and steering feel are improved with better turn-in and input with no downsides. 

The IRP adjustable strut brace bar is a high quality brace that is constructed of 100% steel for guaranteed reinforcement and prevention of flex. The brace bar is painted black to ensure corrosion protection and to add to the looks of the engine bay.

Easily installed with basic hand tools.

Fits the following BMW chassis:
E36 BMW All Submodels