BMW Suspension Parts

M7 Strut Reinforcement Plates 53-510101 are the ultimate solution for MINI owners facing the common issue of strut tower mushrooming caused by heavy impacts from shocks and low aspect ratio tires. Over time, MINI's shock towers can develop a convex shape, disrupting suspension alignment and leading to a noticeable pull to one side. The M7 Strut Reinforcement Plates (SRPs) address this problem by reinforcing the sheet metal and shock top plate, creating a durable surface that resists bending, even during hard impacts.

Designed specifically for the R50 Base Model Cooper, the R52 Convertible, and the R53 Cooper S, these SRPs are an essential upgrade for any MINI enthusiast. Constructed from CNC machined billet aluminum and black anodized for durability, the 1/2" (13mm) thick plates cover the entire surface of the strut tower, distributing loads evenly and providing peace of mind.

Whether you drive your MINI daily or push it to the limits on the track, M7 Strut Reinforcement Plates offer a cost-effective preventative measure against expensive suspension repairs. Easy to install in less than 20 minutes, the SRPs use the stock nuts for mounting and come with instructions that also guide you through fixing existing mushrooming.

• Prevents strut tower mushrooming
• Constructed from CNC machined billet aluminum
• Black anodized for long-lasting durability
• Covers the entire strut tower surface
• Designed for R50, R52, and R53 MINI models
• Easy installation with stock nuts
• Made in the USA

If you are concerned about strut tower mushrooming and looking for improved handling, the M7 Strut Tower Brace (STB) is the solution. This is the ONLY strut tower brace on the market that features anti-mushrooming technology.

Repeatedly, we've heard the same complaint: strut towers mushroom after heavy impacts from shocks and low aspect ratio tires. Initially, the shock towers take on a barely visible convex shape, but if compared to the original sheet metal, you'll find the horizontal plane has moved as much as 3/8" upwards, making alignment nearly impossible.

This issue often shows up as a slight pull to the left or right, depending on which strut tower is affected. The M7 Strut Tower Brace's end mounting plates solve this problem by sandwiching the sheet metal and shock top plate, creating a reinforced surface that won't bend, even during hard impacts.

The M7 STB features 1/2" (13mm) thick end plates that add extra strength to the strut towers, preventing mushrooming and potentially costly repairs. The cross brace significantly improves handling by adding torsional stiffness to the front body structure, helping keep your tires planted and pointed in the direction you want to go, especially during hard turns. Machined from billet aluminum and matte black powder coated, the M7 Strut Tower Brace boasts a durable black finish that looks great and won't chip or oxidize.

We have customers who won't drive their new MINI off the lot without one and dealers that sell every new MINI with either the M7 Strut Reinforcement Plates or the M7 Strut Tower Brace.

Concerned about clearance? No worries. The M7 STB profile is designed to clear both stock and aftermarket cold air intakes and ECUs. Its modular design allows easy access to the oil filter or any other accessories that might normally be blocked and require removal of the entire brace.

Installation is a snap (often taking less than 20 minutes)! No need for new nuts—the brace uses the three stock nuts on each side. Installation instructions are available online by clicking the "INSTALLATION" link on this page.

The M7 Strut Reinforcement Plates and the M7 Strut Tower Brace are two separate products that address strut tower mushrooming (you only need one or the other).

If your MINI is mainly a daily driver, the M7 Strut Reinforcement Plates are sufficient. If you have performance driving in mind, the M7 Strut Tower Brace is what you're looking for!

Please note:

• You cannot buy the SRPs and attach the cross-bar at a later time.
• The brace does not directly fit on the R50 and R52 Non-"S" Cooper due to limited hood clearance of the non-supercharged cars. It will fit but may push up on the hood slightly, requiring molding or cutting of the hood insulation after installation.
• Trimming of the underhood insulation material may be required to fully clear this brace. This is a very tight space.

One of the most common issues with the E46 is that the subframe likes to tear away from the chassis. Fix this by welding in a Rear Subframe reinforcement kit.

• Includes all necessary reinfored metal plates
• Professional installation is required
• Suspension must be realigned after installation

Fits the following BMWs:
1998 - 2006 E46 320i 323i 325i 325xi 328i 330i 323ci 325ci 330ci M3 

Enhance the handling and durability of your MINI with the M7 Speed MAXX-G High Performance Billet Aluminum Adjustable Rear Sway Bar Link Kit. This set of 2 direct replacement parts is compatible with all Gen 3 MINI Coopers and BMW X1 & X2 models. Crafted from CNC machined billet aircraft-grade aluminum, these sway bar links feature durable 90A durometer urethane bushings and forged steel adjustable tie rod ends. The design ensures over 10 times the strength and rigidity of the stock plastic parts, resulting in reduced compliance in the suspension system, improved sway bar response, and increased wheel rate for enhanced grip and control. With sealed and permanently lubricated tie rod ends and corrosion-resistant finishes, this kit guarantees longevity and performance. Upgrade your MINI's handling with the MAXX-G link kit, backed by a lifetime guarantee.

• Direct replacement for stock sway bar links
• Over 10 times stronger and more rigid than stock plastic parts
• Improved sway bar response and increased wheel rate
• Sealed and permanently lubricated tie rod ends for longevity
• Corrosion-resistant finishes for durability
• Lifetime guarantee for all parts