BMW Suspension Parts

The B16 PSS10 coilovers offer a stiffer spring rate than stock and a lower ride height for less bodyroll and better handling. These are among the easiest coil over kits on the market - no special mounts required (works with stock mounts and sway bar links), larger adjustment knob allows for easy shock damping changes, and coil over spanner wrenches included for easy height changes. Bilstein backs up their technology with a limited lifetime warranty. TUV approved for fitment, safety, and quality!

Bilstein's monotube shock dampers in the PSS10 offer 10 precise settings for compression and rebound. A new setting is just a click away, allowing you to set a ride and handling combination that works for your setting. Instead of offering too many shock settings that you're never going to use, Bilstein has chosen ten optimal damping curves from a smooth street setting (P10) to an ultra-stiff track-only setup (P1). Shock changes are made from an easy-to-use over-sized adjuster knob.

Ride height adjustments are done from perches that ride on each shock body, which are zinc coated for excellent wear and corrosion resistance. You can set the ride height between 0.5 to 1.3 inches lower than stock ride height. Springs are progressively rated so their initial compression rating is quite soft and then becomes stiffer as the spring compresses. These are stiffer than most coil over kit manufacturers and the results of Bilstein's extensive testing on the German Nurgburgring and Autobahn.

The fitment of these is just like a standard shock and spring package. The front struts and rear shocks are compatible with the stock strut and shock mounts. You can re-use your own or choose a mount with additional features. Because the Bilstein design keeps the sway bar tab in the original location, you can re-use the stock sway bar links. Using the stock mounts keeps the cost and complexity down and allows for TUV certification. You can also be assured of the stock mount's quiet and long-lasting performance. The assembly of the front strut is the same as a the factory strut. In the rear, ride height is made by an adjustable spring perch that sits under the rear spring. Install instructions and diagrams included.

If you're looking for a supremely capable and high quality suspension, then look no further than the Bilstein PSS10. It combines all of the best German engineering with real-world development, and a lifetime warranty.

Fitment note: this system works only on cars not equipped with the factory EDC electronically adjustable shocks.

Featuring:

• Largest available piston diameter for greater sensitivity and precise control.
• Patented digressive piston head design and deflective valving instantly reacts to changing road conditions.
• 10-way adjustable dampening knobs that "click" from soft to hard with no tools or jacking required.
• Monotube design dissipates heat more effectively than a twin tube shock for cooler, more efficient operation and longer life.
• Weather resistant coating to resist oxidization, and ensure long life.
• Lighter weight reduces wear and tear on suspension components.
• Wrenches to adjust front and rear ride height included!

This item fits the following BMWs:
2001-2006 E46 BMW M3

Bilstein has teamed up with Eibach to offer matched shock and spring packages. These Eibach springs are mated to a special set of Bilstein shocks to deliver a sporty and taut ride with as little impact on ride comfort as possible.

The Pro Kit uses an Eibach Pro Kit spring with Bilstein's Sport shocks and struts. Instead of taking parts from different manufacturers, Bilstein has tested the performance of the Eibach spring and tailored their shocks to be a true match for the new spring rate and ride height. This is known as a matched shock and spring and very few tuning companies take these extra steps. Eibach springs tend to be softer overall than most other aftermarket springs, which ensures the ride stays close to a stock comfort while still giving you a lowered stance and improved handling. 

Bilstein B12 Features: 

• Precise response and excellent driving performance
• Springs and shocks road tested and fine-tuned to complement one another
• Bilstein Monotube/Inverted gas pressure technology
• TUV certified
• Made In Germany
• Average Lowering of 25 to 40mm

Most cars don't need coil overs to improve their handling and bodyroll. For most drivers, simply replacing the shocks and springs with performance versions will meet their goals. If your shocks need replacing, and you felt the handling could be improved a little bit, this is an excellent performance suspension for you.

This item fits the following BMWs:
2006-2008 E85/E86 BMW Z4 M Coupe, M Roadster

Since 1957, Bilstein has been at the forefront of suspension technology, setting industry standards for quality and performance. It all began when Bilstein introduced the world's first mono-tube gas pressure shock absorber for Mercedes-Benz, revolutionizing the way suspensions work. With an illustrious history and an unwavering commitment to driver comfort, Bilstein remains a pioneer in the automotive suspension field.

When it comes to selecting an aftermarket suspension system, Bilstein is the top choice for many discerning enthusiasts. Their dedication to precision, quality, and innovation sets them apart.

The Bilstein Performance Suspension System (PSS)

The Bilstein Performance Suspension System (PSS) is the epitome of high-performance suspension with complete adjustability. Equipped with performance-valved mono-tube gas shocks, this system offers infinite adjustability, allowing you to tailor your ride to your exact preferences. Whether you crave an aggressive track experience or a comfortable daily commute with enhanced travel, the PSS has you covered. The threaded body design permits precise adjustments of the front and rear progressive spring rate springs, enabling you to achieve the ideal ride height and center of gravity for your vehicle.

With Bilstein, you not only get exceptional performance but also peace of mind. All Bilstein components come with a lifetime warranty, making it the last suspension system you'll ever need to purchase for your vehicle.

Notable Features:

• Lowering approximately 30-50 mm at both the front and rear (Note: May require MINI Part # 33506778572 per rear shock).

For all warranty inquiries and to purchase individual components, please reach out to Bilstein directly at 1-800-537-1085. Choose Bilstein, and experience suspension excellence that stands the test of time.

Bilstein has teamed up with Eibach to offer matched shock and spring packages. These Eibach springs are mated to a special set of Bilstein shocks to deliver a sporty and taut ride with as little impact on ride comfort as possible.

The Pro Kit uses an Eibach Pro Kit spring with Bilstein's Sport shocks and struts. Instead of taking parts from different manufacturers, Bilstein has tested the performance of the Eibach spring and tailored their shocks to be a true match for the new spring rate and ride height. This is known as a matched shock and spring and very few tuning companies take these extra steps. Eibach springs tend to be softer overall than most other aftermarket springs, which ensures the ride stays close to a stock comfort while still giving you a lowered stance and improved handling. 

Bilstein B12 Features: 

• Precise response and excellent driving performance
• Springs and shocks road tested and fine-tuned to complement one another
• Bilstein Monotube/Inverted gas pressure technology
• TUV certified
• Made In Germany
• Average Lowering of 25 to 40mm

Most cars don't need coil overs to improve their handling and bodyroll. For most drivers, simply replacing the shocks and springs with performance versions will meet their goals. If your shocks need replacing, and you felt the handling could be improved a little bit, this is an excellent performance suspension for you.

This item fits the following BMWs:
1989-1995 E34 BMW 535i 530i

Bilstein has teamed up with Eibach to offer matched shock and spring packages. These Eibach springs are mated to a special set of Bilstein shocks to deliver a sporty and taut ride with as little impact on ride comfort as possible.

The Pro Kit uses an Eibach Pro Kit spring with Bilstein's Sport shocks and struts. Instead of taking parts from different manufacturers, Bilstein has tested the performance of the Eibach spring and tailored their shocks to be a true match for the new spring rate and ride height. This is known as a matched shock and spring and very few tuning companies take these extra steps. Eibach springs tend to be softer overall than most other aftermarket springs, which ensures the ride stays close to a stock comfort while still giving you a lowered stance and improved handling. 

Bilstein B12 Features: 

• Precise response and excellent driving performance
• Springs and shocks road tested and fine-tuned to complement one another
• Bilstein Monotube/Inverted gas pressure technology
• TUV certified
• Made In Germany
• Average Lowering of 25 to 40mm

Most cars don't need coil overs to improve their handling and bodyroll. For most drivers, simply replacing the shocks and springs with performance versions will meet their goals. If your shocks need replacing, and you felt the handling could be improved a little bit, this is an excellent performance suspension for you.

This item fits the following BMWs:
1995-2001 E38 BMW 740i/iL

Bilstein has teamed up with Eibach to offer matched shock and spring packages. These Eibach springs are mated to a special set of Bilstein shocks to deliver a sporty and taut ride with as little impact on ride comfort as possible.

The Pro Kit uses an Eibach Pro Kit spring with Bilstein's Sport shocks and struts. Instead of taking parts from different manufacturers, Bilstein has tested the performance of the Eibach spring and tailored their shocks to be a true match for the new spring rate and ride height. This is known as a matched shock and spring and very few tuning companies take these extra steps. Eibach springs tend to be softer overall than most other aftermarket springs, which ensures the ride stays close to a stock comfort while still giving you a lowered stance and improved handling. 

Bilstein B12 Features: 

• Precise response and excellent driving performance
• Springs and shocks road tested and fine-tuned to complement one another
• Bilstein Monotube/Inverted gas pressure technology
• TUV certified
• Made In Germany
• Average Lowering of 25 to 40mm

Most cars don't need coil overs to improve their handling and bodyroll. For most drivers, simply replacing the shocks and springs with performance versions will meet their goals. If your shocks need replacing, and you felt the handling could be improved a little bit, this is an excellent performance suspension for you.

This item fits the following BMWs:
1989-1995 E34 BMW 525i

Bilstein has teamed up with Eibach to offer matched shock and spring packages. These Eibach springs are mated to a special set of Bilstein shocks to deliver a sporty and taut ride with as little impact on ride comfort as possible.

The Pro Kit uses an Eibach Pro Kit spring with Bilstein's Sport shocks and struts. Instead of taking parts from different manufacturers, Bilstein has tested the performance of the Eibach spring and tailored their shocks to be a true match for the new spring rate and ride height. This is known as a matched shock and spring and very few tuning companies take these extra steps. Eibach springs tend to be softer overall than most other aftermarket springs, which ensures the ride stays close to a stock comfort while still giving you a lowered stance and improved handling. 

Bilstein B12 Features: 

• Precise response and excellent driving performance
• Springs and shocks road tested and fine-tuned to complement one another
• Bilstein Monotube/Inverted gas pressure technology
• TUV certified
• Made In Germany
• Average Lowering of 25 to 40mm

Most cars don't need coil overs to improve their handling and bodyroll. For most drivers, simply replacing the shocks and springs with performance versions will meet their goals. If your shocks need replacing, and you felt the handling could be improved a little bit, this is an excellent performance suspension for you.

This item fits the following BMWs:
2011-2016 F10 BMW 535i/d

Unveiling the BMW Coilover Line, meticulously crafted for the daily driver's needs. Engineered to elevate performance, aesthetics, and comfort, these coilovers offer a perfect blend of firmness and compliance. With 32 levels of damping and height adjustments tailored to each car, they deliver an aggressive look and significantly enhanced handling.

Key Features:

• ECS Tuning Performance Coilover System:
  • Sport-tuned, height, damping, and body adjustable suspension
  • 32 levels of rebound damping adjustment
  • Adjustable front sway bar end links
  • Integrated camber plates for +/-1.5 degrees of adjustment
  • Lowering adjustment of 1.5" - 4"
  • Heat-treated, progressive rate coil springs (8k Front, 10K Rear)
  • Zinc-coated threaded portions for corrosion protection
  • Powder-coated Reflex Silver Metallic finish on coil springs
  • Red anodized, billet aluminum spring seats with locking collars
  • Anodized adjustable sway bar end links with heavy-duty bushings
  • Zinc-coated flanged nuts for shock & strut shaft pins
  • Rear shock adjuster housings black E-coated for durability
  • Integrated bump stops and dust boots

Turner Performance Adjustable Rear Toe Links:

Enhance stability and response with Turner's Performance Rear Toe Links. These links eliminate bushing deflection, providing increased rear toe adjustment crucial for lowered cars or performance alignments. With gun-drilled 2024 Aluminum center links, rotating clamp design, and low-friction Teflon-lined FK Heim joints, this pair ensures superior strength, durability, and ease of adjustment. A must-have for optimal grip on the track and extended tire life on the street.

Bilstein has teamed up with Eibach to offer matched shock and spring packages. These Eibach springs are mated to a special set of Bilstein shocks to deliver a sporty and taut ride with as little impact on ride comfort as possible.

The Pro Kit uses an Eibach Pro Kit spring with Bilstein's Sport shocks and struts. Instead of taking parts from different manufacturers, Bilstein has tested the performance of the Eibach spring and tailored their shocks to be a true match for the new spring rate and ride height. This is known as a matched shock and spring and very few tuning companies take these extra steps. Eibach springs tend to be softer overall than most other aftermarket springs, which ensures the ride stays close to a stock comfort while still giving you a lowered stance and improved handling. 

Bilstein B12 Features: 

• Precise response and excellent driving performance
• Springs and shocks road tested and fine-tuned to complement one another
• Bilstein Monotube/Inverted gas pressure technology
• TUV certified
• Made In Germany
• Average Lowering of 25 to 40mm

Most cars don't need coil overs to improve their handling and bodyroll. For most drivers, simply replacing the shocks and springs with performance versions will meet their goals. If your shocks need replacing, and you felt the handling could be improved a little bit, this is an excellent performance suspension for you.

This item fits the following BMWs:
2008-2012 E9X BMW M3

Introducing the all-new BMW Coilover line, meticulously crafted with daily drivers in mind. This line focuses on enhancing suspension performance and aesthetics without compromising comfort. Offering a smooth, stock-like feel, these coilovers provide an aggressive look and significantly improved handling at an unbeatable price.

Key Features:

• ECS Tuning Performance Coilover System:
  • Sport-tuned, height, damping, and body adjustable suspension
  • 32 levels of rebound damping adjustment
  • Optimized progressive rate coil springs with adjustable damping monotube shocks/struts
  • Lower ride height for improved handling with reduced body roll
  • Adjustable front bodies for personalized ride height and correct spring pre-load
  • Durable gloss black powder-coated strut and shock bodies
  • Clear zinc-coated threaded portions for corrosion protection
  • Powder-coated Reflex Silver Metallic finish on coil springs
  • Red anodized, billet aluminum lower spring seats with locking collars
  • Integrated bump stops for added durability

Turner Motorsport Upgraded Thrust Arm With Pre-installed Monoball Bushings:

Addressing the common issues of weak front thrust arm bushings in BMWs, this upgrade ensures optimal handling, braking performance, and an enhanced driving experience.

Features:

• Ball Joint / Monoball:
  • OEM BMW sealed, greased ball joint for exceptional durability
• Housing:
  • 6061-T6 anodized housing for excellent corrosion resistance
  • Proprietary Turner designed knurled OD for a perfect fit among different thrust arm bore diameters
• Bearing Inserts:
  • CNC machined 304ss for a precision fit between the ball joint and the subframe
• Performance:
  • Nearly instantaneous, crisp steering and braking response
  • Maintenance-free, long-lasting performance
  • Improved road feel without undesirable NVH

Upgrade your driving experience with these essential enhancements suitable for both street and track enthusiasts.

The B16 PSS10 coilovers offer a stiffer spring rate than stock and a lower ride height for less bodyroll and better handling. These are among the easiest coil over kits on the market - no special mounts required (works with stock mounts and sway bar links), larger adjustment knob allows for easy shock damping changes, and coil over spanner wrenches included for easy height changes. Bilstein backs up their technology with a limited lifetime warranty. TUV approved for fitment, safety, and quality!

Bilstein's monotube shock dampers in the PSS10 offer 10 precise settings for compression and rebound. A new setting is just a click away, allowing you to set a ride and handling combination that works for your setting. Instead of offering too many shock settings that you're never going to use, Bilstein has chosen ten optimal damping curves from a smooth street setting (P10) to an ultra-stiff track-only setup (P1). Shock changes are made from an easy-to-use over-sized adjuster knob.

Ride height adjustments are done from perches that ride on each shock body, which are zinc coated for excellent wear and corrosion resistance. You can set the ride height between 0.5 to 1.3 inches lower than stock ride height. Springs are progressively rated so their initial compression rating is quite soft and then becomes stiffer as the spring compresses. These are stiffer than most coil over kit manufacturers and the results of Bilstein's extensive testing on the German Nurgburgring and Autobahn.

The fitment of these is just like a standard shock and spring package. The front struts and rear shocks are compatible with the stock strut and shock mounts. You can re-use your own or choose a mount with additional features. Because the Bilstein design keeps the sway bar tab in the original location, you can re-use the stock sway bar links. Using the stock mounts keeps the cost and complexity down and allows for TUV certification. You can also be assured of the stock mount's quiet and long-lasting performance. The assembly of the front strut is the same as a the factory strut. In the rear, ride height is made by an adjustable spring perch that sits under the rear spring. Install instructions and diagrams included.

If you're looking for a supremely capable and high quality suspension, then look no further than the Bilstein PSS10. It combines all of the best German engineering with real-world development, and a lifetime warranty.

Fitment note: this system works only on cars not equipped with the factory EDC electronically adjustable shocks.

Featuring:

• Largest available piston diameter for greater sensitivity and precise control.
• Patented digressive piston head design and deflective valving instantly reacts to changing road conditions.
• 10-way adjustable dampening knobs that "click" from soft to hard with no tools or jacking required.
• Monotube design dissipates heat more effectively than a twin tube shock for cooler, more efficient operation and longer life.
• Weather resistant coating to resist oxidization, and ensure long life.
• Lighter weight reduces wear and tear on suspension components.
• Wrenches to adjust front and rear ride height included!

This coilover kit fits the following BMWs:
2014+ F22 BMW 228xi M235xi - Not for cars with EDC
2012+ F30 BMW 320xi 328xi 335xi - Sedan - Not for cars with EDC
2013+ F32 BMW 428xi 435xi - Coupe - Not for cars with EDC
2014+ F34 BMW 328i xDrive GT, 335i xDrive GT - Gran Tourismo
2014+ F36 BMW 428i xDrive Gran Coupe 435i xDrive Gran Coupe

The Bilstein B14 PSS Suspension allows adjustable vehicle ride height without the expense of a fully adjustable damping system. This system features both coilover and standard mono-tube gas pressure shock or struts with performance level valving for application specific, progressive rate coil springs.
The product benefits at a glance:

• Threaded body adjustable range of 20 mm
• Lowering of approx. 30-50 mm at front and rear
• Road-tested and fine-tuned by BILSTEIN ride engineers, under extreme motorsports conditions
• Aluminum Spring plates and lock nuts
• Surface coating using Triple-C-Technology for long-lasting corrosion resistance
• Round threads for easy adjustment
• Quality sport springs made from highly durable material
• Gas pressure technology

BILSTEIN monotube technology, made in Germany

adj. -1.0"-1.75" / adj. -1.0"-1.75"

Not for cars with EDC

Fits these vehicles:
1997-2003 E39 BMW 528i 525i 530i

The B16 PSS10 coilovers offer a stiffer spring rate than stock and a lower ride height for less bodyroll and better handling. These are among the easiest coil over kits on the market - no special mounts required (works with stock mounts and sway bar links), larger adjustment knob allows for easy shock damping changes, and coil over spanner wrenches included for easy height changes. Bilstein backs up their technology with a limited lifetime warranty. TUV approved for fitment, safety, and quality!

Bilstein's monotube shock dampers in the PSS10 offer 10 precise settings for compression and rebound. A new setting is just a click away, allowing you to set a ride and handling combination that works for your setting. Instead of offering too many shock settings that you're never going to use, Bilstein has chosen ten optimal damping curves from a smooth street setting (P10) to an ultra-stiff track-only setup (P1). Shock changes are made from an easy-to-use over-sized adjuster knob.

Ride height adjustments are done from perches that ride on each shock body, which are zinc coated for excellent wear and corrosion resistance. You can set the ride height between 0.5 to 1.3 inches lower than stock ride height. Springs are progressively rated so their initial compression rating is quite soft and then becomes stiffer as the spring compresses. These are stiffer than most coil over kit manufacturers and the results of Bilstein's extensive testing on the German Nurgburgring and Autobahn.

The fitment of these is just like a standard shock and spring package. The front struts and rear shocks are compatible with the stock strut and shock mounts. You can re-use your own or choose a mount with additional features. Because the Bilstein design keeps the sway bar tab in the original location, you can re-use the stock sway bar links. Using the stock mounts keeps the cost and complexity down and allows for TUV certification. You can also be assured of the stock mount's quiet and long-lasting performance. The assembly of the front strut is the same as a the factory strut. In the rear, ride height is made by an adjustable spring perch that sits under the rear spring. Install instructions and diagrams included.

If you're looking for a supremely capable and high quality suspension, then look no further than the Bilstein PSS10. It combines all of the best German engineering with real-world development, and a lifetime warranty.

Fitment note: this system works only on cars not equipped with the factory EDC electronically adjustable shocks.

Featuring:

• Largest available piston diameter for greater sensitivity and precise control.
• Patented digressive piston head design and deflective valving instantly reacts to changing road conditions.
• 10-way adjustable dampening knobs that "click" from soft to hard with no tools or jacking required.
• Monotube design dissipates heat more effectively than a twin tube shock for cooler, more efficient operation and longer life.
• Weather resistant coating to resist oxidization, and ensure long life.
• Lighter weight reduces wear and tear on suspension components.
• Wrenches to adjust front and rear ride height included!

This coilover kit fits the following BMWs:
2014+ F22 BMW 228i M235i - Not for cars with EDC
2012+ F30 BMW 320i 328i 335i - Sedan - Not for cars with EDC
2013+ F32 BMW 428i 435i - Coupe - Not for cars with EDC