The B16 PSS10 coilovers offer a stiffer spring rate than stock and a lower ride height for less bodyroll and better handling. These are among the easiest coil over kits on the market - no special mounts required (works with stock mounts and sway bar links), larger adjustment knob allows for easy shock damping changes, and coil over spanner wrenches included for easy height changes. Bilstein backs up their technology with a limited lifetime warranty. TUV approved for fitment, safety, and quality!

Bilstein's monotube shock dampers in the PSS10 offer 10 precise settings for compression and rebound. A new setting is just a click away, allowing you to set a ride and handling combination that works for your setting. Instead of offering too many shock settings that you're never going to use, Bilstein has chosen ten optimal damping curves from a smooth street setting (P10) to an ultra-stiff track-only setup (P1). Shock changes are made from an easy-to-use over-sized adjuster knob.

Ride height adjustments are done from perches that ride on each shock body, which are zinc coated for excellent wear and corrosion resistance. You can set the ride height between 0.5 to 1.3 inches lower than stock ride height. Springs are progressively rated so their initial compression rating is quite soft and then becomes stiffer as the spring compresses. These are stiffer than most coil over kit manufacturers and the results of Bilstein's extensive testing on the German Nurgburgring and Autobahn.

The fitment of these is just like a standard shock and spring package. The front struts and rear shocks are compatible with the stock strut and shock mounts. You can re-use your own or choose a mount with additional features. Because the Bilstein design keeps the sway bar tab in the original location, you can re-use the stock sway bar links. Using the stock mounts keeps the cost and complexity down and allows for TUV certification. You can also be assured of the stock mount's quiet and long-lasting performance. The assembly of the front strut is the same as a the factory strut. In the rear, ride height is made by an adjustable spring perch that sits under the rear spring. Install instructions and diagrams included.

If you're looking for a supremely capable and high quality suspension, then look no further than the Bilstein PSS10. It combines all of the best German engineering with real-world development, and a lifetime warranty.

Fitment note: this system works only on cars not equipped with the factory EDC electronically adjustable shocks.

Featuring:

• Largest available piston diameter for greater sensitivity and precise control.
• Patented digressive piston head design and deflective valving instantly reacts to changing road conditions.
• 10-way adjustable dampening knobs that "click" from soft to hard with no tools or jacking required.
• Monotube design dissipates heat more effectively than a twin tube shock for cooler, more efficient operation and longer life.
• Weather resistant coating to resist oxidization, and ensure long life.
• Lighter weight reduces wear and tear on suspension components.
• Wrenches to adjust front and rear ride height included!

This coilover kit fits the following BMWs:
2008+ E82 BMW 128i 135i
2006+ E90 BMW 325i 328i 330i 335d 335i
2007+ E92 BMW 328i 335i 335is
2007+ E93 BMW 328i 335i

If you are concerned about strut tower mushrooming and looking for improved handling, the M7 Strut Tower Brace (STB) is the solution. This is the ONLY strut tower brace on the market that features anti-mushrooming technology.

Repeatedly, we've heard the same complaint: strut towers mushroom after heavy impacts from shocks and low aspect ratio tires. Initially, the shock towers take on a barely visible convex shape, but if compared to the original sheet metal, you'll find the horizontal plane has moved as much as 3/8" upwards, making alignment nearly impossible.

This issue often shows up as a slight pull to the left or right, depending on which strut tower is affected. The M7 Strut Tower Brace's end mounting plates solve this problem by sandwiching the sheet metal and shock top plate, creating a reinforced surface that won't bend, even during hard impacts.

The M7 STB features 1/2" (13mm) thick end plates that add extra strength to the strut towers, preventing mushrooming and potentially costly repairs. The cross brace significantly improves handling by adding torsional stiffness to the front body structure, helping keep your tires planted and pointed in the direction you want to go, especially during hard turns. Machined from billet aluminum and matte black powder coated, the M7 Strut Tower Brace boasts a durable black finish that looks great and won't chip or oxidize.

We have customers who won't drive their new MINI off the lot without one and dealers that sell every new MINI with either the M7 Strut Reinforcement Plates or the M7 Strut Tower Brace.

Concerned about clearance? No worries. The M7 STB profile is designed to clear both stock and aftermarket cold air intakes and ECUs. Its modular design allows easy access to the oil filter or any other accessories that might normally be blocked and require removal of the entire brace.

Installation is a snap (often taking less than 20 minutes)! No need for new nuts—the brace uses the three stock nuts on each side. Installation instructions are available online by clicking the "INSTALLATION" link on this page.

The M7 Strut Reinforcement Plates and the M7 Strut Tower Brace are two separate products that address strut tower mushrooming (you only need one or the other).

If your MINI is mainly a daily driver, the M7 Strut Reinforcement Plates are sufficient. If you have performance driving in mind, the M7 Strut Tower Brace is what you're looking for!

Please note:

• You cannot buy the SRPs and attach the cross-bar at a later time.
• The brace does not directly fit on the R50 and R52 Non-"S" Cooper due to limited hood clearance of the non-supercharged cars. It will fit but may push up on the hood slightly, requiring molding or cutting of the hood insulation after installation.
• Trimming of the underhood insulation material may be required to fully clear this brace. This is a very tight space.

M7 Strut Reinforcement Plates 53-510101 are the ultimate solution for MINI owners facing the common issue of strut tower mushrooming caused by heavy impacts from shocks and low aspect ratio tires. Over time, MINI's shock towers can develop a convex shape, disrupting suspension alignment and leading to a noticeable pull to one side. The M7 Strut Reinforcement Plates (SRPs) address this problem by reinforcing the sheet metal and shock top plate, creating a durable surface that resists bending, even during hard impacts.

Designed specifically for the R50 Base Model Cooper, the R52 Convertible, and the R53 Cooper S, these SRPs are an essential upgrade for any MINI enthusiast. Constructed from CNC machined billet aluminum and black anodized for durability, the 1/2" (13mm) thick plates cover the entire surface of the strut tower, distributing loads evenly and providing peace of mind.

Whether you drive your MINI daily or push it to the limits on the track, M7 Strut Reinforcement Plates offer a cost-effective preventative measure against expensive suspension repairs. Easy to install in less than 20 minutes, the SRPs use the stock nuts for mounting and come with instructions that also guide you through fixing existing mushrooming.

• Prevents strut tower mushrooming
• Constructed from CNC machined billet aluminum
• Black anodized for long-lasting durability
• Covers the entire strut tower surface
• Designed for R50, R52, and R53 MINI models
• Easy installation with stock nuts
• Made in the USA

M7 Speed Suspension Product for Generation 2 MINI Cooper Models (R55-R59)

M7 Speed proudly introduces a unique suspension product for the popular Generation 2 MINI Cooper models R55 through R59. These affordable vehicles are becoming the choice for many entry-level modifiers in the German performance car segment, and they are great for Rally Cross.

Engineered to transform the mild-mannered MINI into a more capable and versatile daily driver, this product is perfect for today’s lifestyle. Whether it's for spirited adventure motoring, weekend overlanding, living off the grid, or tackling pothole-riddled urban streets, the M7 Speed 2" Lift Kit makes it possible. By installing this lift kit, the MINI is elevated by 2 inches, plus an additional lift from larger diameter tires (up to an extra 1.5 inches). No additional modifications are required—simply bolt it in, perform a realignment, and enjoy! Add aftermarket wheels and larger tires to create a unique, durable, and practical vehicle that everyone will love.

The M7 Speed Stage 1 Kit includes everything needed for the transformation. This kit features precision-fabricated lift blocks and a set of MAXX-G heavy-duty adjustable front sway bar links. These shorter links are necessary to prevent suspension bind that can occur with stock-length sway bar links.

Stage 1 Kit Includes:

• 2" Lift Kit with high-strength assembly hardware (2 front riser blocks, 2 rear riser blocks)
• Set of MAXX-G Heavy Duty Adjustable Front Sway Bar Links
• Hardware kit with high-strength, proper-length bolts and new locking nuts

Features:

• Engineered using 3D CAD software and finite element simulation for proper fitment and safe, fail-proof performance
• CNC laser-cut parts
• Lightweight fabricated steel design
• Black urethane powder coating for corrosion protection and a quality appearance
• Designed for easy bolt-on installation, complete with all new high-strength hardware and installation instructions

MAXX-G Adjustable Sway Bar:

• Enhances cornering performance, provides bind-free suspension travel, improves suspension alignment, and overall chassis balance
• Features sealed and permanently lubricated forged steel ball stud & socket ends for easy installation
• Includes a military-grade aluminum adjuster sleeve with opposing RH & LH threads for simple length adjustments
• Replaceable link ends make maintenance easy

M7 Speed is the world leader in MINI adventure motoring, overlanding, and ultimate performance products. Renowned for exceptional customer service and product innovation, M7 Speed is dedicated to engineering and producing high-quality, easy-to-install aftermarket performance products. Located in Mooresville, North Carolina, also known as Race City USA, M7 Speed is at the epicenter of North American motorsports.

Enhance your BMW's performance and aesthetics with CTS Turbo's high-quality lowering springs. Crafted from durable SAE 9254/DIN 54SiCr6 Spring Steel Wire, these springs ensure safety, strength, and long-term durability.

Key Features:

• Designed for street use, focusing on handling, braking, and responsiveness without compromising ride comfort
• In-house engineered and extensively tested to ensure no detrimental effects on OEM struts over long-term use
• Lowers the car for a more aggressive appearance while reducing wheel gap, maintaining daily drivability
• DCC compatible, ensuring compatibility with dynamic damper control for consistent ride characteristics across modes

Lowering Specs:

• Front: Approximately 1.0" lowering
• Rear: Approximately 1.0" lowering

Featured Advantages:

• Improved handling and ride quality
• Enhanced aesthetics with a more aggressive look and reduced fender gap

Notes:

• CTS suspension components should be installed by a qualified licensed mechanic experienced in suspension installations
• Final ride height settles after a few days of driving

Removes and installs control arm bushings while leaving the control arm on the car.

From 1974 to 2019, Bavarian Autosport was one of the premier vendors for BMW and MINI auto parts. We are happy to preserve the Bav Auto legacy by continuing to carry their high-quality products into the future. All Bav Auto parts will remain unchanged in design and sourced from the same OEM suppliers to ensure long-lasting reliability. We trust these parts, accessories, and upgrades so confidently that we back every Bavarian Autosport branded component with a 2-year warranty.