BMW Suspension Parts

Improve your BMW's driving experience by addressing the wear and tear caused by years on the road. The suspension takes a beating from pot holes, speed bumps, and road hazards, leading to a weakened and sloppy feel. Enhance safety and ride comfort by replacing worn components, such as the control arm.

• Improved driving experience and ride comfort
• Enhanced safety through the replacement of worn suspension components
• Non-serviceable ball joints and other components addressed for prolonged lifespan
• Control arm replacement for a better feel and handling
• Recommended replacement in pairs for optimal performance
• Suitable for both front and rear suspension upgrades
• Referred to as a wishbone by BMW
• Performance upgrade for non-M3 models, recommended to replace in pairs due to heavy-duty nature

Enhance your driving experience with our premium suspension upgrade for your BMW. Over time, the road can take a toll on your suspension, leading to a sloppy and weak feel while driving. Our solution? Replace the control arm – a critical component that, after years of service, may wear out. Boost safety and ride comfort with this easy upgrade.

• Improved driving experience
• Enhanced safety
• Better ride comfort
• Extended service life of replacement parts

If you're considering replacing any part of your front or rear suspension, opt for doing it in pairs (both left and right sides). This ensures optimal performance and longevity of the replacement parts. In the BMW world, it's often referred to as a wishbone.

For non-M3 models, this isn't just a replacement – it's a performance upgrade. These heavy-duty components are recommended to be replaced in pairs to maximize their efficiency and provide a seamless driving experience.

This suspension package of Bilstein Sport shocks and H&R Sport springs will lower the ride height and firm up the suspension to provide less bodyroll and better handling. This E24 and E28 suspension package is firm but not harsh and can be used on daily-driven street cars as well as backroad and weekend corner carvers.

H&R Sport springs lower the ride height by 1.25" and stiffens the spring rate. Both combine to lower the car's center of gravity and reduce the amount of bodyroll in corners. The springs are progressive rate so their initial stiffness is actually very compliant and it becomes stiffer as the spring is compressed. This is great for street cars that see bumps and potholes where suspension compliance is key. Overall, they are about 40% stiffer than the stock original springs. The ride quality is a little stiffer than a stock E28 M5.

We use Bilstein Sport shocks as the dampers and they feature Bilstein's patented and innovative valving system. With this system, small bumps and impacts are absorbed as they should be. But the shocks stiffen for cornering and other suspension motions. It's the best of both worlds as the shock self-adjusts based on suspension motion. These fit with the stock strut and shock mounts, making for an easy and clean install.

Although this suspension is listed for the E28 M5 and E24 M6, the original rear self-leveling system must be disabled or removed.
 

Parts list:

• 1 set - H&R Sport Springs (50428)
• 1 pair - Bilstein Front Sport struts (P36-0243 / 34-181546)
• 1 pair - Bilstein Rear Sport Shocks (B46-0607 / 24-006071)

This item fits the following BMWs:
1982-1988 E28 BMW 528e 533i 535i 535is M5
1982-1989 E24 BMW 633csi 635csi M6

This kit is contains all new strut and shock mounts and hardware needed when installing a new shocks and struts or aftermarket suspension on your vehicle. 

Fits the following BMW's

E46 M3 Coupe 

If E30 needs a little more pep in the corners, this is an excellent suspension package. H&R Sport springs and Bilstein Sport shocks for the E30 will lower the ride height for an aggressive stance and stiffer springs will improve handling and balance in the corners. This suspension is a favorite among our E30 fans because the car corners better without a punishing ride. Perfect for daily-driven E30s who want to carry more speed through the corners.

H&R Sport springs lower the ride height by 1.25" and stiffens the spring rate. Both combine to lower the car's center of gravity and reduce the amount of bodyroll in corners. The springs are progressive rate so their initial stiffness is actually very compliant and it becomes stiffer as the spring is compressed. This is great for street cars that see bumps and potholes where suspension compliance is key. Overall, they are about 40% stiffer than the stock original springs.

We use Bilstein Sport shocks as the dampers and they feature Bilstein's patented and innovative valving system. With this system, small bumps and impacts are absorbed as they should be. But the shocks stiffen for cornering and other suspension motions. It's the best of both worlds as the shock self-adjusts based on suspension motion. These fit with the stock strut and shock mounts, making for an easy and clean install.
 

Parts list:

• 1 set - H&R Sport Springs (50406)
• 1 pair - Bilstein Front Sport strut inserts (P36-0335 / 34-003350)
• 1 pair - Bilstein Rear Sport Shocks (B36-2027 / 24-020275)

Fitment note: Front strut inserts fit the larger 51mm strut housings. These were standard for all 6-cylinder E30s, all M3, and 1989-1992 318i/is. Other models used a smaller strut housing which requires a different Bilstein insert.

This item fits the following BMWs:
1984-1992 E30 BMW 325e 325es 325i 325ic 325is

Eliminate the most common sources of suspension slop with our all new Turner Suspension Refresh Kits that feature only OEM parts! We do not include any "cheap parts" in our refresh kits to ensure long-lasting reliability and noise-free suspension.

This Level 1 kit replaces:

Front Control Arms
Front Control Arm Bushings