Select Vehicle
BMW
Mini
Purpose
Category
-
Oil Lines
Create an account to be able to build Wish Lists.
On the twin-turbocharged M57, all the oil that reaches the turbos goes through this line first. It carries pressurized oil from the engine block to the oil distribution piece, which feeds both the high- and low-pressure turbos. When the factory line’s rubber sections age and its crimped fittings start to leak, the oil spreads across the block and exhaust. The leak also puts the oil supply to both turbos at risk. This line sits deep in the engine and is hard to reach, so it’s a job you only want to do once. We built our braided distribution line to be the last one you install.
The factory line uses rubber hose sections that harden and crack with heat and age. Our version uses a PTFE inner hose wrapped in stainless steel braid, so it stays flexible and leak-free through countless heat cycles. On top of that, a black PVC shell protects the braid in the tight space around the block and keeps the factory look under the hood. Our line comes with new banjo bolts and copper crush washers. It fits in the factory location with no modifications. While you have this area apart, it’s a good time to replace our high-pressure (11427795971) and low-pressure (11427795972) supply lines too.
BMW’s M57 twin-turbo diesel uses its two turbos in stages. A small high-pressure turbo gives quick response at low RPM, and a larger low-pressure turbo takes over for top-end power. The oil line that feeds the high-pressure turbo runs right next to the exhaust manifold, which makes it one of the hottest places on the engine. After enough heat cycles, the factory rubber hose sections get brittle and crack, and the crimped fittings start to leak. You may see oil dripping onto hot exhaust parts, smell burning oil inside the car, or notice smoke from under the hood. If the leak is left alone, the turbo bearings can run short on oil and fail. Our braided supply line fixes this weak spot with a tough PTFE stainless steel line built to take the heat for good.
From the factory, this line is steel tubing joined by rubber flex sections, with an aluminum heat sleeve that holds onto oil once a leak starts. We replace the rubber with a PTFE inner hose wrapped in stainless steel braid. PTFE holds up to heat and oil far better than rubber, and the braid protects against bursts and abrasion. On top of that, a black PVC shell keeps the braid from rubbing against nearby lines and wiring, and it keeps the factory look under the hood. Our line comes with new banjo bolts and copper crush washers. It fits in the factory location with no modifications required.
The M57 twin-turbo diesel’s two-stage setup depends on its large low-pressure turbo once RPM and load increase. The oil line feeding that turbo runs low on the engine, from the oil distribution piece to the turbo, where heat from the exhaust and turbo housing wears down the factory rubber hose sections over time. As the rubber hardens and the crimped fittings loosen, oil starts dripping onto the exhaust and coating the underside of the engine. Left alone, the leak can cut oil flow to a turbo that’s expensive to replace. Our braided low-pressure supply line fixes this weak spot for good.The M57 twin-turbo diesel’s two-stage setup depends on its large low-pressure turbo once RPM and load increase. The oil line feeding that turbo runs low on the engine, from the oil distribution piece to the turbo, where heat from the exhaust and turbo housing wears down the factory rubber hose sections over time. As the rubber hardens and the crimped fittings loosen, oil starts dripping onto the exhaust and coating the underside of the engine. Left alone, the leak can cut oil flow to a turbo that’s expensive to replace. Our braided low-pressure supply line fixes this weak spot for good.
From the factory, this line is rubber hose crimped onto steel fittings, and the rubber is the part that fails. We construct our line using a PTFE inner hose wrapped in stainless steel braid, which holds up to heat, pressure and oil far better than rubber. On top of that, a black PVC shell keeps the braid from chafing against nearby parts and keeps the factory look under the hood. Our line comes with a new banjo bolt, adapter fitting, and copper crush washers. It follows the factory routing and fits in the factory location with no modifications.
From the factory, this line is rubber hose crimped onto steel fittings, and the rubber is the part that fails. We construct our line using a PTFE inner hose wrapped in stainless steel braid, which holds up to heat, pressure and oil far better than rubber. On top of that, a black PVC shell keeps the braid from chafing against nearby parts and keeps the factory look under the hood. Our line comes with a new banjo bolt, adapter fitting, and copper crush washers. It follows the factory routing and fits in the factory location with no modifications.
