BMW Engine Parts

VTT is happy to introduce the first and only available plug and play crankcase breather kits for ALL BMW applications that use the two-prong oil tab style oil fill caps. With this breather simply remove your oil cap, install the breather, and instantly free up horsepower, improve turbo draining, remove crankcase pressure, all while adding a cool look to your engine bay.

Can be used by itself with the stock PCV system to eliminate crankcase pressure, or with any number of PCV setups for the ultimate in crankcase pressure relieve 

Made from 6061-T6 Aircraft aluminum anodized black for a long-lasting finish, 4 stainless steel baffles for complete oil control, a PTFE one way check ball, a high-quality filter, and clamp all work together to keep crankcase pressure where it belongs, out of your crankcase.

This breather will fit:
 ALL BMW's with the two-prong style oil fill cap including but not limited to N54, N55, S55, S54

NOTE: NOT ALL THE MODELS LISTED HAVE THE SAME HOOD CLEARANCE, WE CANNOT SAY WHICH MODELS WILL HAVE CLEARANCE ISSUES, AND WHICH WILL NOT AS WE HAVE NOT TEST IT ON ALL MODELS. IF YOU ARE ORDERING THE BREATHER FOR ANYTHING OTHER THAN AN N54 TEST CLOSE YOUR HOOD CAREFULLY TO ENSURE CLEARANCE IF IT DOES NOT FIT LET US KNOW, AND WE WILL GET YOU A REFUND ONCE THE BREATHER IS RETURNED.

MODEL LIST OF REPORTED CLEARANCE ISSUES: N55 E/F 3 SERIES

BMW's Single-VANOS M52 and S52 engines were equipped with plastic valve covers from the factory. Nearing thirty years post-production, this material choice has proven to be problematic. Due to years of exposure to extreme engine temperatures and chemical-rich engine oil, these plastic valve covers will eventually warp. This results in a valve cover that will not seal, requiring a complete replacement of both the plastic valve cover and associated gaskets.

To remedy this, many enthusiasts opt to swap for the magnesium valve cover found on M50 and S50 engines. Unfortunately, magnesium is no less resistant to heat-induced warpage than plastic.

Thankfully, Bremmen Parts is aware of these issues and has created an exact-fit, high-quality performance replacement for all Single-VANOS M52 and S52-equipped BMWs. This cover features durable aluminum construction, which eliminates the warping issue found on OE plastic and magnesium valve covers. Unlike the OE magnesium cover upgrade, Bremmen's aluminum cover retains the forward oil fill location found, allowing you to retain your existing engine beauty cover.

Whether you're replacing a warping plastic cover or preemptively replacing this failure-prone component, Bremmen has you covered with a direct-fit aluminum valve cover upgrade.

The N54 suffers from a weak point in its crankshaft. It has been reported that when increasing the power to the engine, the crank hub can move or spin slightly under an extreme load. This is most apparent under high-rev downshifts or in the case of increased boost pressure which creates more stress on the engines rotating assembly. In order to keep this from happening, the crank bolt must be secured to the hub to keep it from backing off, but this can be a tricky solution since a simple dab of Loctite will not suffice. 

Here is an easy, and cost-effective way to secure the situation; The VTT N54 crank bolt capture. This lightweight and durable ring slips over the head of the crank bolt fully encapsulating it, and locks it to the crank hub and eliminating its ability to spin. The VTT-CBC is 100% Billet Aircraft Grade Aluminum, Anodized black to protect it from the elements, and give it a stealth look. What's more is that it weighs only 1.3 Oz's meaning you aren't adding excess mass to the crankshaft which will avoid any imbalance or vibration issues.

While this is not a full fix for all crank hub spinning issues, the engineers at Vargas have found most issues have stemmed from the bolt itself backing out, and this is a great way to keep that from happening. Extremely lightweight at only 1.3 Oz's it adds virtually no weight to the crank which is important for balance and vibration.

Kit Includes:

• 1x Aluminum Crank Bolt Capture
• 8x Fasteners Gr. 12.9

This part fits the following BMWs:
2006-2013 N54 

Oil leaks from the valve cover are a common issue on high-mileage S55 engines and should be addressed before they lead to bigger problems. Repeated heat cycles can cause the original plastic valve cover and gasket to warp, crack, or lose their seal over time. This Bremmen aluminum valve cover for the BMW S55 engine is a premium upgraded replacement, engineered for superior strength and longevity. Featuring a durable aluminum housing and an integrated PCV system, it offers a reliable, direct-fit solution to replace the factory valve cover and restore proper engine sealing.

Features pre-installed valve cover gasket and integrated PCV. Without oil cap!

The camshaft position sensor is essential for assisting the engine DME by monitoring the camshaft's position. The data from this sensor is key to optimizing ignition timing and ensuring smooth engine performance.

Often referred to as the CMP sensor, this component is crucial for the overall functionality of the powertrain. A failing camshaft position sensor can cause a range of issues, including engine stumbling, hesitation during acceleration, power loss, and even starting difficulties or complete failure to start.