BMW Engine Parts

The alternator in your vehicle keeps the battery at full charge when your engine is running. Because all of your electronic systems run off of this small piece, it's important that it is operational. If your lights are dim while driving or your battery dies within minutes of starting your car, it's time for a new alternator.

This is a NEW alternator from the OEM manufacturer, Valeo. No core charge applies.

This is a Valeo brand new 170 amp alternator. These alternators are built especially for extremes of heat, cold and high demand. Your BMW deserves nothing less than the best, which is why an OEM alternator is the best option. BMW alternators are built to last using the highest quality materials and the most technologically advanced processes. All alternator parts are 100% factory tested to assure that they meet or exceed original equipment specifications. And every alternator is fully load tested to guarantee compliance with BMW's strict performance specifications.

No core charge!

This item fits the following BMWs:
2006-2010 E60 BMW M5
2006-2010 E63 BMW M6

The Precision Raceworks G8x/G2x Stand Alone Auxiliary Fuel System is the highest-performing and most stable low-pressure fuel system on the market! Forget about how things have been done and embrace the benefits of dedicated fueling for your port injection!

Since direct injection came out for BMW, enthusiasts have been adding port injection.  With this came the need to upgrade the low-pressure fuel system to keep up.  Historically this was done by increasing the output of the main fuel system.  Unfortunately, the main fuel pump is controlled using PWM by a factory programmed controller designed to reduce output when target fuel pressure (typically 5 bar) is exceeded, creating a constant battle when pumps are added or upgraded.  This limits upgraded fuel pumps from performing to their full potential.

Additionally, the high-pressure pump control system dumps fuel back into the low-pressure system at high pressure low volume resulting in oscillations of the low-pressure fuel system.  Because of this, the DI system in the car is required to constantly make corrections to keep target AFR in check.

With this stand-alone low-pressure fuel system dedicated to your port fueling that is a thing of the past!  Get rock-solid fuel pressures at any pressure, run fuel pressures that are 1:1 scalable to boost pressure, flow more fuel with dedicated lines, run smaller injectors and still get more fuel than you did with large injectors (allowing for higher resolution), put less demand on the car’s DI system to correct for fluctuations in pressure, even your tuner will be grateful as the system makes tuning of port fueling even easier and more accurate, the list of benefits goes on and on!

Features & Benefits

Billet Aluminum top hat with 3 high-flow fuel ports

Dedicated fuel pump(s) for port injection system

Optimal pump location resistant to fuel slosh under acceleration

Fully adjustable 1:1 scaling billet fuel pressure regulator

10-micron USA made Microglass fuel filter (Ideal for E85)

Smooth bore high flow PTFE fuel feed & return lines (AN6)

All billet connections for both fuel line fittings and top-hat

Plug and play connectors inside and outside* the top hat

Configurable pump activation harness (see instructions for more details)

Increased injector flow (when using 1:1 regulator feature vs static)

Compatible with all stock or upgraded primary fuel pumps

Easily expandable and upgrade-able for more fuel

All components and parts feature 100% Ethanol Compatibility

The AFS.640 dedicated auxiliary fuel system comes with all** necessary components to provide dedicated fuel system for port injection.  Featuring Two Walbro 450’s (F9000274) fuel pumps with a combined flow of 640LPH at 3 bar.

Pump flow 43.5 psi-a : 640 lph

Recommended base pressure: 43.5 psi-g

Maximum Fuel Pressure: 110 psi-g

Number of Fuel Output Ports: 2

Number of Fuel Return Ports: 1

Pump 1: Walbro 450 (F90000274)

Pump 2: Walbro 450 (F90000274)

Available (unused) Electrical Connections: 2*

Total System Weight: 14 lbs (including fuel lines and wiring harness)

*At time of install some wiring in the car may need to be cut and spliced to connectors included in this kit

**Male AN8-ORB to Female AN6-ORB adapter may be required for compatibility with some fuel rails (not included in kit)