Ensure proper sealing when installing the turbos on your N54.

Kit includes:

• 16 - ASA M7x39 studs
• 16 - Flange nuts
• All required gaskets and o-rings
• Water pump install hardware
• Replacement vacuum hose
• T-bolt clamps

Helpful hints:

For complete installation instructions, refer to Haynes Service Manual (T#193950).

Both downpipes must be removed to remove either front or rear turbo. Tie rod end may need to be separated from knuckle for clearance. Steering rack may also need to be rotated away from subframe for access. Valve cover heat shield will need to loosened and pushed upward to get clearance for turbo manifold removal.

If studs back out of cylinder head and nuts are seized to studs, replace studs. Thread studs in to head by hand to prevent cross threading. When installing the new studs in the cylinder head, use a high temperature loctite in the cylinder head side, and copper anti-seize on the nut side.

To make more room for access to the front turbo, remove the rubber line running in front of the subframe that attaches to the back of the map thermostat and remove the clip. Cut off the OEM clamp and replace it with a new hose clamp as well.

Complete removal of the water pump is not required. Detach the water pump from the side of the block and push it out of the way to make more room for access to the front turbo. If water pump is unbolted from the block, the aluminum bolts must be replaced.

Torque specs:
Bracket to cylinder head: 9Nm
Coolant supply line to crankcase: 9Nm
Coolant return line to crankcase: 8Nm
Coolant return line to turbo: 8Nm
Coolant supply line to supply line: 8Nm
Exhaust manifold heat shield: 8Nm
Oil supply line to crankcase: 20Nm
Oil pressure line to turbo: 8Nm
Oil return line to crankcase: 8Nm
Oil return line to turbo: 8Nm
Turbo manifold to head: 20Nm

Used in the turbo system to help hold vacuum.
When doing any sort of repair or maintenance there is no replacement for genuine factory parts. Turner Motorsport carries the Genuine BMW brand with pride and has the parts you need to complete your next project with confidence.

Genuine BMW Vacuum Tank
This item fits the following BMW Chassis:
E82 1M Coupe,E82,E90,E92,E93

Fits BMW Engines including:
N54,N54T

Product Description:

M7 Speed proudly presents the Limited Edition Turbo Heat Shield for all Gen 2 Turbocharged 1.6-liter MINI Coopers. This exclusive release features the same top-selling heat shield, now in a custom Hacienda Wrinkle Red powder coat finish. Perfectly complementing the limited edition MAXX Flo intake system also available in this striking red finish.

This new color has gained popularity among young tuner enthusiasts, adding a vibrant touch under the hood and a distinct WOW effect for MINI owners aiming to stand out. Made in the USA from 0.09in [2.2mm] heavy gauge aluminum material, CNC laser cut, and CNC formed, this heat shield ensures consistently high quality. Lined with ceramic thermal insulation on the underside, it minimizes heat transfer to the hood and top side of the engine compartment, proven effective even on professional race cars subjected to extreme heat.

Features and Benefits:

• Fits both the N14 and N18 MINI 1.6-liter turbocharged engines.
• Open design allows heat to escape down and away from the turbo, enhancing heat rejection through radiator airflow.
• Ceramic thermal insulation reduces heat transfer, preserving the engine bay, hood, hood scoop, and hood graphics.
• Simple DIY installation, mounting directly to the engine at easily accessible factory holes.
• All necessary mounting hardware included, with a 15-30 minute installation using basic hand tools.
• Adds a finished look to the engine compartment, enhancing the WOW! effect.
• Acts as an additional layer of protection for the hood and hood scoop, used alongside the factory turbo heat shield.
• PROUDLY MADE IN THE USA.

M7 Speed leads the way in MINI adventure motoring, overlanding, and ultimate performance products. Committed to exceptional customer service and product innovation, we engineer and produce high-quality, easy-to-install aftermarket performance products. Located in Mooresville, North Carolina, known as Race City USA, we're at the heart of North American motorsports. Access Secret Premium Dashboard

Enhance the performance of your BMW's N63 4.4L engine with Genuine BMW Intake Gaskets, priced each for your convenience. Designed specifically for E7X, F0X, and F1X models, these gaskets ensure a tight seal and optimal airflow for maximum engine efficiency.

Key Benefits:

• Genuine BMW quality for reliability and longevity
• Designed for precise fit and compatibility with N63 4.4L engines
• Ensures a tight seal to prevent air leaks and maintain engine performance
• Priced each for cost-effective replacement and maintenance

Upgrade your BMW's intake system with Genuine BMW Intake Gaskets and experience improved engine performance and efficiency.

Key components to help get your install done easily and effectively. Get your car running right again!

Kit includes:​

• All required gaskets and o-rings
• All exhaust and downpipe gaskets
• T-bolt clamps
• 1gal of Coolant