Find Parts That Fit Your Vehicle

BMW Fuel System Parts

Looking for a BMW fuel pump, BMW gas cap or other BMW fuel system related items? You've found the right place. Your BMW fuel delivery system is a critical system, and any failure can rended your BMW dead in the water. Whether your fuel pump has stopped pumping, a fuel injector is clogged or not spraying, or your gas cap is either lost or not properly sealing, we likely have what you are looking for. We stock thousands of BMW fuel system parts so if you don't see what you are looking for, just give us a call.

Sub-Categories

Sort By:

VTT N54 Vacuum Pump Block Off Plate

T#:11497328

Part#: VTT-N54-VACUUM-B

In Stock

$ 127.99 USD

Add to Wish List

Qty

$ 127.99 USD

Add to Wish List

Looking to remove the HPFP or DI system on your N54? this plate will block the vacuum pump and prevent oil leaks. You will need to remove any fuel lines, etc. Kit includes Block Plate Note – Plates may come in a clear or anodize black finish depending on stock on hand

Show More Show Less

VTT BMW N54 “DI Injector” Delete Kit

T#:11497326

Part#: VTT-N54-DI-DELET

Ships in 1 Business Day

$ 339.99 USD

Add to Wish List

Qty

$ 339.99 USD

Add to Wish List

Looking to get rid of the troublesome and expensive DI injectors on your BMW N54 and move to PI only and a standalone? If so VTT has you covered with its new N54 PI delete kit. This kit allows you to SAFELY remove the DI injectors, install our delete fittings, and run PI only. We machined these deletes from 310 Stainless for extreme heat, and corrosion resistance, and include 3 hold downs. These DI deletes COMPLETELY get rid of all factory provisions, including the seal. If the seal is left intact with no fuel to cool the injector or delete it will quickly overheat and melt the delicate seal causing combustion gasses to escape the engine creating misfires, and worse possibly damaging your injector bore on the cylinder head. Our deletes are machined to be a press fit into the cylinder, and can be either cooled with liquid nitrogen, and dropped in, or tapped in with a hammer, and then held down with the included hold downs. We also include M6 tapped holes on the top of each one in case they need to be removed you can attach a slide hammer, and remove the delete. These are sold as a kit and come with the following 6 – 310 Stainless DI Delete fittings 3 – Hold down brackets Completetion of this kit will require the purchase of HPFP delete plate - ES# 4623950 PLEASE NOTE: THIS KIT REQUIRES EXTENSIVE MODIFICATIONS TO CONVERT YOUR ENGINE TO PI ONLY. THIS INCLUDES BUT IS NOT LIMITED TO A FULL PORT INJECTION SOLUTION, AND STAND-ALONE TO RUN THE PI SYSTEM. WE RECOMMEND THIS PNP SYSTEM USING THE MAXX ECU IT PROVIDES ALL YOU NEED TO GET UP AND RUNNING WITH PI ONLY ON THE TUNING SIDE OF THINGS – https://www.pnpecu.com/pnpecu-maxxecu-n54-pnp-kit-437-p.asp

Show More Show Less

MTX-D: Ethanol Content % And Fuel Temperature Gauge

T#:22558994

Part#: INN3904

In Stock at Vendor

14% off MSRP $ 313.99

MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.

$ 269.00 USD

Add to Wish List

Qty

14% off MSRP

$ 313.99

MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.

$ 269.00 USD

Add to Wish List

Introducing the Innovate Motorsports MTX Digital Series "Dual Function" Gauges – now available! These 2 1/16" (52mm) gauges come with interchangeable faceplates and bezels, locking connectors for simplified installation, and MTS serial connections for seamless integration with other Innovate devices for data logging.

DISPLAY RANGE

Ethanol Content %: 0-100%
Temperature: -40-257 °F (-40-125°C)

KEY FEATURES

Ethanol Content
Error reporting for ethanol content sensor (Digital Display)
Fuel Temperature
Customizable exterior LED display
Programmable exterior LED color options
Selectable unit of measure in °F or °C
Programmable fuel temperature warning (outer LED)
2-Configurable analog outputs
Ethanol Content: 0v = 0%, 5v = 100%
Fuel Temperature: 0v = -40 °F, 5v = 257 °F (-40-125°C)

MTX-D: Ethanol Content Percentage & Fuel Temp Gauge Kit includes Gauge (Black Faceplate, Black Bezel), Silver Bezel & White Faceplate, Harness, Program Cable (Serial), Ethanol Content Sensor, Quick Start Installation Guide.

Please note that this is a universal fitment gauge, and installation may vary depending on the vehicle.

Show More Show Less

Vargas Plug And Play S58 Single HPFP Conversion Kit - BMW G8X/F9X S58...

T#:51778123

Part#: VTT-S58-SINGLE-H

In Stock

$ 349.00 USD

Add to Wish List

Qty

$ 349.00 USD

Add to Wish List

The Vargas Turbo Technologies (VTT) S58 Single HPFP Conversion Kit is a revolutionary solution for high-horsepower BMW G8X and F9X builds.

PFS F97/F98 Drop In Brushless LPFP Upgrade - 1000whp Capable ...

T#:26938343

Part#: PFS-LPFP-X3/4M-N

In Stock

$ 1,763.99

This product was last offered at the strikethrough price on
07-22-2026

$ 1,637.99 USD

Limited Qty Sale

Add to Wish List

Qty

$ 1,763.99

This product was last offered at the strikethrough price on
07-22-2026

$ 1,637.99 USD

Limited Qty Sale

Add to Wish List

PFS is proud to offer a true drop-in 1000WHP+ capable LPFP for the F9X X3/4M. This LPFP needs NO additional pumps, wiring harnesses, etc etc. It will support up to 800WHP on Ethanol percentages as high as E98 and will support much higher power levels with less E content as long as you have the octane to support it. For the pump, we start with a factory bucket, we modify it extensively to accept our custom PFS Brushless fuel pump. We then re-terminate the factory wiring to accept the new pump. No wiring splices, done the same way the factory does -the right way. Every single pump is then fully tested on our flow bench to ensure proper function before shipping -you’re going to be installing a product that has already proven itself. This pump is a true drop-in meaning you pull the factory unit out, install this pump, plug the factory plug into the hat, and you are done. The stock ECU controls the pump fully, and NO tune changes are required to take advantage of it. Brand new build: You keep your old pump, we send you a brand-new PFS bucket

Show More Show Less

PFS Port Injection Kit - B58

Aftermarket charge pipe required

T#:5663657

Part#: PFS-B58-PI

Ships in 10 Business Days

Starting at $ 733.99 USD

Add to Wish List

Starting at $ 733.99 USD

Add to Wish List

The kit includes all the parts needed for installation and has a choice of 550CC, or 900CC US-made DW injectors (larger available by request), and a Motiv Reflex Controller

Vargas Shotgun Single Barrel - MT - BMW E9X, E8X N54

T#:52305464

Part#: STGN-SB-1-N54-MT

Ships in 10 Business Days

$ 939.99 USD

Add to Wish List

Qty

$ 939.99 USD

Add to Wish List

The VTT Single Barrel for Manual Transmissions is the "Stage 1" of the Shotgun family, providing a massive headroom increase over the stock setup.

Vargas Port Injection Block Off Injector Blanks With Rail - BMW G8X F...

T#:52164930

Part#: S58PIBLORAIL

Ships in 10 Business Days

$ 222.99 USD

Add to Wish List

Qty

$ 222.99 USD

Add to Wish List

Maximize the versatility of your BMW S58 fuel system with the Vargas Turbo Technologies Port Injection Block Off Kit with Rail.

Vargas Port Injector Block Off Blanks - BMW G8X F9X S58

T#:52164927

Part#: S58PIBLOBLANKS

Ships in 10 Business Days

$ 112.99 USD

Add to Wish List

Qty

$ 112.99 USD

Add to Wish List

The PFS S58 Port Injection Block-Off Kit offers a robust and reliable way to seal secondary fuel ports in the S58 intake manifold.

PFS Port Injection Kit - BMW G8X/F9X S58

T#:52164908

Part#: PFS-S58-PI-NONE

Ships in 10 Business Days

$ 949.99 USD

Add to Wish List

Qty

$ 949.99 USD

Add to Wish List

The PFS S58 Port Injection Kit by Vargas Turbo Technologies is the solution for BMW owners who have reached the limits of their factory injection.

Vargas HPFP Block-Off Plate - BMW B58 & S58

T#:51672724

Part#: VTT-X58-HPFP-BLO

Ships in 10 Business Days

$ 99.99 USD

Add to Wish List

Qty

$ 99.99 USD

Add to Wish List

The VTT Billet B58 HPFP Block-off Plate allows you to cleanly remove the bulky factory pump, reducing engine bay clutter and weight.

PFS G8X Drop In Brushless LPFP Upgrade - 1000whp Capable

T#:26938293

Part#: PFS-LPFP-G8X-NEW

Back Ordered

$ 1,763.99 USD

Add to Wish List

Qty

$ 1,763.99 USD

Add to Wish List

PFS is proud to offer a true drop-in 1000WHP+ capable LPFP for G -Series S58. This LPFP needs NO additional pumps, wiring harnesses, etc etc. It will support up to 800WHP on Ethanol percentages as high as E98 and will support much higher power levels with less E content as long as you have the octane to support it. For the pump, we start with a factory bucket, we modify it extensively to accept our custom PFS Brushless fuel pump. We then re-terminate the factory wiring to accept the new pump. No wiring splices, done the same way the factory does -the right way. Every single pump is then fully tested on our flow bench to ensure proper function before shipping -you’re going to be installing a product that has already proven itself. This pump is a true drop-in meaning you pull the factory unit out, install this pump, plug the factory plug into the hat, and you are done. The stock ECU controls the pump fully, and NO tune changes are required to take advantage of it. Brand new build: You keep your old pump, we send you a brand new PFS bucket

Show More Show Less

Upgraded Low Pressure Fuel Pump Assembly

Call In Or Chat For Best Price!

T#:14188788

Part#: R420-0002

Back Ordered

11% off MSRP $ 1,631.99

MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.

$ 1,449.99 USD

Add to Wish List

Qty

11% off MSRP

$ 1,631.99

MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.

$ 1,449.99 USD

Add to Wish List

As power output increases, the demand for low-pressure fuel pumps increases. This kit includes components to upgrade your low-pressure fuel pump to deliver consistent fuel flow regardless of the amount of fuel inside the tank while increasing tank drawing. Best of all, the modified pump can be properly controlled by the DME and will result in no fault codes. Complete modified fuel pump Increases tank draw Consistent fuel flow Works seamlessly with existing DME For over 35 years, Dinan has been America's premier tuning company, pioneering advancements in BMW modification while retaining a focus on balanced performance that preserves the original character and driving feel that a BMW offers. When you install a Dinan part on your car, know that it's not only carefully developed and tested, but that Dinan stands behind it with a four-year, 50,000-mile warranty. Dinan believes so fully in their “total package” approach that once your car has been fitted with enough of their parts, they celebrate your conversion from stock to Dinan with an exclusive trunk badge, displayed proudly by BMW enthusiasts everywhere.

Project Cars

SELECT YOUR BMW

BMW Fuel System Parts

Sub-Categories

VTT N54 Vacuum Pump Block Off Plate

VTT BMW N54 “DI Injector” Delete Kit

MTX-D: Ethanol Content % And Fuel Temperature Gauge

Vargas Plug And Play S58 Single HPFP Conversion Kit - BMW G8X/F9X S58...

PFS F97/F98 Drop In Brushless LPFP Upgrade - 1000whp Capable ...

PFS Port Injection Kit - B58

Vargas Shotgun Single Barrel - MT - BMW E9X, E8X N54

Vargas Port Injection Block Off Injector Blanks With Rail - BMW G8X F...

Vargas Port Injector Block Off Blanks - BMW G8X F9X S58

PFS Port Injection Kit - BMW G8X/F9X S58

Vargas HPFP Block-Off Plate - BMW B58 & S58

PFS G8X Drop In Brushless LPFP Upgrade - 1000whp Capable

Upgraded Low Pressure Fuel Pump Assembly

Select Vehicle

Purpose

Category

Brand

Price

Special Offers

Shipping

Narrow Results