Find Parts That Fit Your Vehicle

KMAC Camber Plates

One of the tricks for getting your BMW to handle better is to add negative camber to the front wheels. This will put more of the tire's width in contact with the ground during cornering. With more rubber there is more grip. BMWs typically have less camber in the front to create understeer. But if you're running a stock setup on the track or autocross you are giving up speed and time as the front tires run out of grip sooner than they should. Here at Turner Motorsport, we offer a variety of camber plates, including our own in-house engineered version, so that you can pick out a solution that works best for your BMW.

Sort By:

KMAC Stage 1 Street Front Adjustable Camber/Caster Plates - E39 540/M...

affirm Starting At 0% APR - Subject To Eligibility. See Lending Terms

T#:389661

Part#: 193616-1J

In Stock

$ 380.00 USD

Add to Wish List

Qty

$ 380.00 USD

Add to Wish List

Location: Front
Type: Street, Stage 1
Bearing: captive-ball fully encased in polyurethane

These front adjustable camber/caster plates will replace your stock front upper strut bearing. The KMAC plates are a 'floating' design so camber and caster are adjusted together. This design allows maximum range of adjustment since no other hardware interferes with the adjustments. Since these replace your stock strut bearings they are designed to work with a stock-type spring only. And when installed correctly will not significantly alter ride height. Adjustment is easily done by loosening the three nuts on top of the tower and sliding the camber plate into the position you want, then re-tighten the nuts. These mounts can be installed two ways - for camber correction or swapped side-side for increasing negative camber. Detailed instructions included.

Note: suspensions vary from manufacturer to manufacturer. Turner Motorsport cannot be responsible for fitment issues caused by non-stock or specialized coil-over suspensions. As with any race-derived component, additonal fabrication may be required.

This item fits the following BMWs:
1997-2003 E39 BMW 525i 528i 530i 540i (for cars with EDC)
1999-2003 E39 BMW M5
1995-2001 E38 BMW 740i 740il 750il (for cars with EDC)

Show More Show Less

K-MAC Stage 1 Street - Front Adjustable Camber/Caster Plates ...

affirm Starting At 0% APR - Subject To Eligibility. See Lending Terms

T#:388807

Part#: 195116-1J

Special Order: No Guaranteed ETA

$ 380.00 USD

Add to Wish List

Qty

$ 380.00 USD

Add to Wish List

Location: Front
Type: Street, Stage 1
Bearing: captive-ball fully encased in polyurethane

These front adjustable camber/caster plates will replace your stock front upper strut bearing. The KMAC plates are a 'floating' design so camber and caster are adjusted together. This design allows maximum range of adjustment since no other hardware interferes with the adjustments. Since these replace your stock strut bearings they are designed to work with a stock-type spring only. And when installed correctly will not significantly alter ride height. Adjustment is easily done by loosening the three nuts on top of the tower and sliding the camber plate into the position you want, then re-tighten the nuts. These mounts can be installed two ways - for camber correction or swapped side-side for increasing negative camber. Detailed instructions included.

Note: suspensions vary from manufacturer to manufacturer. Turner Motorsport cannot be responsible for fitment issues caused by non-stock or specialized coil-over suspensions. As with any race-derived component, additonal fabrication may be required.

This item fits the following BMWs:
3/2002-2006 R50 MINI MINI Cooper
2005-2008 R52 MINI MINI Cooper Convertible, MINI Cooper S Convertible.
3/2002-2006 R53 MINI MINI Cooper S

Show More Show Less

KMAC Stage 3 Track Front Adjustable Camber/Caster Plates - E39 540/M5...

affirm Starting At 0% APR - Subject To Eligibility. See Lending Terms

T#:389662

Part#: 193616-3L

Special Order: No Guaranteed ETA

$ 545.00 USD

Add to Wish List

Qty

$ 545.00 USD

Add to Wish List

Location: Front
Type: Track, Stage 3
Bearing: PTFE-lined pillow-ball, no bushing

KMAC Stage 3 camber/caster plates are designed for track or race-only situations where comfort and noise are not the primary concerns. The Stage 3 camber plates use a pillowball bearing, solidly mounted within the camber plate for direct alignment of the strut shaft and no excess play or deflection. Stage 3 are designed to increase negative camber with their patented 'floating' adjustment that changes camber and caster together. This design allows maximum range of adjustment since no other hardware interferes with the adjustments. Fitment is limited to race-only small diameter coil-over springs (not stock-type). Bearing inserts and adapters included. Detailed instructions included.

Note: suspensions vary from manufacturer to manufacturer. Turner Motorsport cannot be responsible for fitment issues caused by non-stock or specialized coil-over suspensions. As with any race-derived component, additonal fabrication may be required.

This item fits the following BMWs:
1997-2003 E39 BMW 525i 528i 530i 540i (for cars with EDC)
1999-2003 E39 BMW M5
1995-2001 E38 BMW 740i 740il 750il (for cars with EDC)
2004-2010 E60 BMW M5
2004-2011 E63 BMW M6

Show More Show Less

KMAC Stage 2 Street/Track Front Adjustable Camber/Caster Plates - E39...

affirm Starting At 0% APR - Subject To Eligibility. See Lending Terms

T#:389317

Part#: 193616-2L

Special Order: No Guaranteed ETA

$ 545.00 USD

Add to Wish List

Qty

$ 545.00 USD

Add to Wish List

Location: Front
Type: Street/Track, Stage 2
Bearing: PTFE-lined pillow-ball with thin polyurethane bushing

The Stage 2 KMAC plates are a mixed street/track camber/caster plate meant to be used in a variety of suspensions. Since there is less bushing than on the Stage 1, more noise and vibration will reach the driver. The adjustment design is similar to the Stage 1 with a floating mount that sets camber and caster simultaneously. This design allows maximum range of adjustment since no other hardware interferes with the adjustments. These plates can work on both coil over and stock-stype suspensions. Bearing inserts and adapters included. The Stage 2 camber plates are shorter than a factory mount so may not be suitable for cars will little suspension travel. These are designed mainly for adding negative camber for improved handling and not for camber correction back to stock settings (see Stage 1 kit). Detailed instructions included.

Note: suspensions vary from manufacturer to manufacturer. Turner Motorsport cannot be responsible for fitment issues caused by non-stock or specialized coil-over suspensions. As with any race-derived component, additonal fabrication may be required.

This item fits the following BMWs:
2006-2008 E85 BMW Z4 M Roadster M Coupe

Show More Show Less

K-MAC Stage 2 Street/Race - Front Adjustable Camber/Caster Plates 195...

affirm Starting At 0% APR - Subject To Eligibility. See Lending Terms

T#:7371477

Part#: 195416-2L

Special Order: No Guaranteed ETA

$ 545.00 USD

Add to Wish List

Qty

$ 545.00 USD

Add to Wish List

Upgrade your Mini's front top strut mounts with the K-MAC ultimate design. These mounts offer separate Camber and Caster adjustment, ensuring precise alignment even under load. Made from high-grade aircraft aluminum, they are durable and lightweight. With K-MAC's patented system, adjustments are quick and easy, allowing you to switch between Street and Race settings in just 30 seconds. The design also features heavy-duty centers encased in elastomer for extended life and minimal stack height.

Separate Camber and Caster adjustment
Quick and easy adjustments
Made from aircraft grade 7075 aluminum
Durable and lightweight construction
Compatible with OEM diam springs or smaller coil overs

Show More Show Less

K-MAC Stage 1 Street - Front Adjustable Camber/Caster Plates ...

affirm Starting At 0% APR - Subject To Eligibility. See Lending Terms

T#:388808

Part#: 195016-1J

In Stock

37% off MSRP $ 380.00

MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.

$ 238.99 USD

Limited Qty Sale

Add to Wish List

Qty

37% off MSRP

$ 380.00

MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.

$ 238.99 USD

Limited Qty Sale

Add to Wish List

KMAC Stage 1 Street Camber/Caster Plates

affirm Starting At 0% APR - Subject To Eligibility. See Lending Terms

T#:591419

Part#: 191716-1J

Special Order: No Guaranteed ETA

$ 380.00 USD

Add to Wish List

Qty

$ 380.00 USD

Add to Wish List

These front adjustable camber/caster plates will replace your stock front upper strut bearing. The KMAC plates are a 'floating' design so camber and caster are adjusted together. This design allows maximum range of adjustment since no other hardware interferes with the adjustments. Since these replace your stock strut bearings they are designed to work with a stock-type spring only.

Show More Show Less

Project Cars

SELECT YOUR BMW

KMAC Camber Plates

KMAC Stage 1 Street Front Adjustable Camber/Caster Plates - E39 540/M...

K-MAC Stage 1 Street - Front Adjustable Camber/Caster Plates ...

KMAC Stage 3 Track Front Adjustable Camber/Caster Plates - E39 540/M5...

KMAC Stage 2 Street/Track Front Adjustable Camber/Caster Plates - E39...

K-MAC Stage 2 Street/Race - Front Adjustable Camber/Caster Plates 195...

K-MAC Stage 1 Street - Front Adjustable Camber/Caster Plates ...

KMAC Stage 1 Street Camber/Caster Plates

Select Vehicle

Category

Brand

Price

Narrow Results