Front Control Arm

Improve your BMW's driving experience by addressing the wear and tear caused by years on the road. The suspension takes a beating from pot holes, speed bumps, and road hazards, leading to a weakened and sloppy feel. Enhance safety and ride comfort by replacing worn components, such as the control arm.

• Improved driving experience and ride comfort
• Enhanced safety through the replacement of worn suspension components
• Non-serviceable ball joints and other components addressed for prolonged lifespan
• Control arm replacement for a better feel and handling
• Recommended replacement in pairs for optimal performance
• Suitable for both front and rear suspension upgrades
• Referred to as a wishbone by BMW
• Performance upgrade for non-M3 models, recommended to replace in pairs due to heavy-duty nature

Enhance your driving experience with our premium suspension upgrade for your BMW. Over time, the road can take a toll on your suspension, leading to a sloppy and weak feel while driving. Our solution? Replace the control arm – a critical component that, after years of service, may wear out. Boost safety and ride comfort with this easy upgrade.

• Improved driving experience
• Enhanced safety
• Better ride comfort
• Extended service life of replacement parts

If you're considering replacing any part of your front or rear suspension, opt for doing it in pairs (both left and right sides). This ensures optimal performance and longevity of the replacement parts. In the BMW world, it's often referred to as a wishbone.

For non-M3 models, this isn't just a replacement – it's a performance upgrade. These heavy-duty components are recommended to be replaced in pairs to maximize their efficiency and provide a seamless driving experience.

Swapping in E46 control arms into your E30 or E36 significantly increases negative camber by widening the track width and also gives you more clearance for more steering angle. Condor's CNC machined control arm brackets are made from solid steel and are fitted with a solid hex-shaped bushing. Designed for the street or the track, they hold the control arm steady and eliminate "shimmy" caused by stock bushings. They sharpen steering and improve overall driving feel. Comparable to the NLA Treehouse E36 & E30 Eyeball Arms.

Easiest install of any aftermarket solution
Allow clearance for E30 M50 Conversion exhaust
Street Approved, marginal increase in NVH
Easy Installation, no need for a press
CNC machined steel construction
Solid design without the maintenance of spherical bearings
Heavy-Duty replaceable UHMW insert. Don't be misinformed, UHMW is the best material for these inserts. Delrin is not self-lubricating and will crack and degrade over time.
Powder coated white for corrosion resistance
Improve caster with M3 offset geometry
Keep proper steering geometry under high loads
Made in the U.S.A.
Fitment:
E30 84-91 3 Series
E36 92-98 3 series & Z3

Note that you will need to use E36 outer tie rods and E90 inner tie rods when installing in an E30 or E36

Be sure to measure your control arms to determine if you need 21mm or 23mm. Meyle makes a standard e46 control arm and a Heavy Duty control arm. Most HD arms have a hex that is larger in size (23mm). Lifetime Warranty

Upgrade your BMW's performance with the Genuine BMW Aluminum Front Lower Control Arm - Right for E34 and E31 models. Crafted with precision, this control arm ensures superior handling and durability for your vehicle. Designed to exact BMW specifications, this part guarantees a perfect fit and optimal performance. Elevate your driving experience with Turner Motorsport.

• Enhances handling and control
• Durable aluminum construction
• Exact fit for E34 and E31 models
• Optimizes performance
• Genuine BMW quality assurance

Swapping in E46 control arms into your E30 or E36 will significantly increase negative camber by widening the track width and will also give you more clearance for more steering angle. Condor's conversion bushings are machined from UHMW due to its high rigidity and low coefficient of friction allowing for minimal suspension bushing deflection (geometry change). They've designed them offset to re-center the wheel and give your e30/e36 the correct caster. They will include a stainless-steel insert that tightly presses over the hex pattern on the E46 control arms. You do not need to grind down your control arms or make any other modifications to your chassis. Please note that you will need to use E36 outer tie rods and E90 inner tie rods when installing in an E30 or E36.

Fitment:
Fits the following Meyle and Lemforder arms with 21-22MM Hex.

LEMFORDER ZHP - 31122282121 & 31122282122
LEMFORDER - 31126777851 & 31126777852
MEYLE HD - 31126777851 & 31126777852
*Please note that Meyle makes a standard e46 control arm and a Heavy Duty control arm. SOME HD arms have a hex that is larger in size. These HD control arms may need to be shaved 1-2 mm for proper fitment.