BMW Control Arm Replacements & Upgrades

G8X / F8X Adjustable Toe Arm Set | Fall-Line Motorsports - Standard by Turner Motorsport is crafted to enhance the alignment process for BMW enthusiasts. Made in the USA, this standard toe link kit facilitates rapid toe adjustments during alignment, and when combined with the tension strut, it also allows for precise track adjustments. Designed for easy fitment, these arms simplify wheel alignment and camber adjustment, making the setup process quicker and more efficient.

• Enhanced Alignment: Enables fast and precise toe adjustments for improved wheel fitment.
• Track Adjustment: Works in conjunction with the tension strut for overall track adjustments.
• Simplified Setup: Eases camber adjustment and simplifies alignment processes.
• Direct Replacement: Matches OEM part number 33322284534 // 33-32-2-284-534.
• Multi-Link Suspension Compatibility: Handles dynamic changes in alignment settings effectively.

Fits:

• G80 / G81 / G82 / G83 M3 & M4
• F80 / F82 M3 & M4
• G87 M2
• F87 M2

Swapping in E46 control arms into your E30 or E36 significantly increases negative camber by widening the track width and also gives you more clearance for more steering angle. Condor's CNC machined control arm brackets are made from solid steel and are fitted with a solid hex-shaped bushing. Designed for the street or the track, they hold the control arm steady and eliminate "shimmy" caused by stock bushings. They sharpen steering and improve overall driving feel. Comparable to the NLA Treehouse E36 & E30 Eyeball Arms.

Easiest install of any aftermarket solution
Allow clearance for E30 M50 Conversion exhaust
Street Approved, marginal increase in NVH
Easy Installation, no need for a press
CNC machined steel construction
Solid design without the maintenance of spherical bearings
Heavy-Duty replaceable UHMW insert. Don't be misinformed, UHMW is the best material for these inserts. Delrin is not self-lubricating and will crack and degrade over time.
Powder coated white for corrosion resistance
Improve caster with M3 offset geometry
Keep proper steering geometry under high loads
Made in the U.S.A.
Fitment:
E30 84-91 3 Series
E36 92-98 3 series & Z3

Note that you will need to use E36 outer tie rods and E90 inner tie rods when installing in an E30 or E36

Be sure to measure your control arms to determine if you need 21mm or 23mm. Meyle makes a standard e46 control arm and a Heavy Duty control arm. Most HD arms have a hex that is larger in size (23mm). Lifetime Warranty

Swapping in E46 control arms into your E30 or E36 will significantly increase negative camber by widening the track width and will also give you more clearance for more steering angle. Condor's conversion bushings are machined from UHMW due to its high rigidity and low coefficient of friction allowing for minimal suspension bushing deflection (geometry change). They've designed them offset to re-center the wheel and give your e30/e36 the correct caster. They will include a stainless-steel insert that tightly presses over the hex pattern on the E46 control arms. You do not need to grind down your control arms or make any other modifications to your chassis. Please note that you will need to use E36 outer tie rods and E90 inner tie rods when installing in an E30 or E36.

Fitment:
Fits the following Meyle and Lemforder arms with 21-22MM Hex.

LEMFORDER ZHP - 31122282121 & 31122282122
LEMFORDER - 31126777851 & 31126777852
MEYLE HD - 31126777851 & 31126777852
*Please note that Meyle makes a standard e46 control arm and a Heavy Duty control arm. SOME HD arms have a hex that is larger in size. These HD control arms may need to be shaved 1-2 mm for proper fitment.

When an E9X is lowered beyond the limits of just lowering springs, the rear wheels toe-in excessively. This excessive rear toe leads to premature wear, that many people attribute to an increase in negative camber. It has become a common belief that an extremely low vehicle will wear the tires wrong as a matter of consequence. It has become standard practice to go as low as you can and proceed to replace your tires every five to ten thousand miles. Whats more is that when the vehicle reaches a certain ride height, the factory arms become maxed out and there is no way to compensate and dial in the proper toe. You're left with an improperly aligned vehicle that is in effect worse off than it was with the stock suspension installed.

This is not only uneconomical but improper and unsafe. ECS Tuning is proud to offer a solution for this problem in the form of Rogue Engineering E9X adjustable rear toe arms. These arms allow for greater toe adjustment on vehicles that have been lowered with a coilover suspension. With the toe set properly the tires can contact the road properly this maximizes grip and minimizes wear. 

Features:

• 100% machined and anodized, 6061-T6 lightweight aluminum arms
• High-strength, 3-piece, rod end (with carbon fiber reinforced, PTFE race) offers longer life for street compared to standard rod ends
• SEALS-IT Rod end seals keep dirt, water, and other contaminants out
• Rod ends feature grease fittings, to allow for rod end serviceability.
• Lighter than stock!  (Stock is 875g, RE arms are 640g)
• Extremely easy installation and adjustment (your alignment shop will LOVE you!)

BMW E9X M3/E82 1M Inner Lower Tension Arm Bearing is engineered to elevate suspension performance with precision and durability. Developed by Fall-Line, known for their championship-level race cars and premium suspension components, this bearing is a significant upgrade over factory rubber bushings. Designed for motorsport applications, it incorporates FK spherical bearings for enhanced strength and longevity.

• Superior Performance: Provides a notable improvement over OEM rubber bushings for enhanced control and feedback.
• Durable Construction: Features the largest FK spherical bearings available, ensuring long-lasting reliability.
• Enhanced Control: Eliminates rubber components to offer better control over tire behavior and increased driver confidence.
• Robust Design: Equipped with stainless steel spiral locks for 360 degrees of clamping force to secure the bearing firmly.
• Long-Lasting: Outperforms OEM rubber variants, reducing the need for frequent replacements.
• Precision Engineering: CNC machined from high-quality materials in the USA for exact fit and superior performance.