VTT S55 Crank Bolt Capture - F8X S55 F3x N55

T#:557934

Part#: VTT-S55-CBC

In Stock

$ 129.99 USD

Add to Wish List

Qty

$ 129.99 USD

Add to Wish List

The S55 suffers from a weak point in its crankshaft. It has been reported that when increasing the power to the engine, the crank hub can move or spin slightly under an extreme load.

Vargas "Spline Lock" Crank Hub Solution - Includes Crank Bolt Capture...

T#:558795

Part#: VTT-CRANKHUB-1

In Stock

$ 889.99 USD

Add to Wish List

Qty

$ 889.99 USD

Add to Wish List

Under certain conditions, the N55 crank hub likes to spin, without warning and even when the engine is in perfect health. The engineers at Vargas saw and dealt with this problem time and again, and they saw fit to do something about it. This hub uses a proprietary "Spline Lock" technology that uses high tolerance machined splines which press into the crank, and positively lock the hub to the crank. The splines are machined in such a way that rotational forces drive the hub, and splines deeper into the crank meaning when the hub encounters a situation that would normally slip a stock hub the splined hub is driven into the crank to keep it in place (much like a splined extractor). Features: Installs the same as a stock hub Does NOT require the crank to be drilled for pins Manufactured from Harndered 17-4SS We suggest the Crank Hub System ONLY be installed by a qualified shop or technician. Timing tools are 100% REQUIRED if installed improperly engine damage may occur. DISCLAIMER: VTT and ECS are not responsible for any engine damage caused by improper installation, or misuse of the crank hub solution.

Show More Show Less

Elring Cylinder Head Installation Kit - S52 3.2L

2X Entries For Our G87 M2 Sweepstakes! We Price Match - Give Us A Call or Chat!

T#:367024

Part#: 11129069861

In Stock

$ 379.99

This product was last offered at the strikethrough price on
04-06-2026

$ 214.99 USD

Add to Wish List

Qty

$ 214.99 USD

Add to Wish List

If there is a large amount of oil on the sides of the engine or if you can smell burning oil, chances are it's a bad valve cover gasket. The gasket fails and allows oil to seep down onto the side of the engine and other parts causing a mess and reducing the amount of oil in your engine. This replacement gasket from Elring is perfect to prevent any further oil leaks.

Includes everything needed to re-seal your engine's head.

Elring is one of the biggest OEM names in the manufacturing of high quality gaskets that are available for very affordable prices. Elring has supplied many automotive names for years with the gaskets that seal your car's components from day 1 so you can rest assured that these components will last for a long time to come!

Fits the following engines:
S52 3.2L

Show More Show Less

Spline Lock Crank Hub Solution W/ Complete Package - N55 S55 ...

T#:18733532

Part#: VTT-CRANKHUB-6

Ships in 6 Business Days

$ 986.99

This product was last offered at the strikethrough price on
06-28-2026

$ 939.99 USD

Add to Wish List

Qty

$ 939.99 USD

Add to Wish List

Under certain conditions, the N55 crank hub likes to spin, without warning and even when the engine is in perfect health. The engineers at Vargas saw and dealt with this problem time and again, and they saw fit to do something about it. This hub uses a proprietary "Spline Lock" technology that uses high tolerance machined splines which press into the crank, and positively lock the hub to the crank. The splines are machined in such a way that rotational forces drive the hub, and splines deeper into the crank meaning when the hub encounters a situation that would normally slip a stock hub the splined hub is driven into the crank to keep it in place (much like a splined extractor). Features: Installs the same as a stock hub Does NOT require the crank to be drilled for pins Manufactured from Harndered 17-4SS We suggest the Crank Hub System ONLY be installed by a qualified shop or technician. Timing tools are 100% REQUIRED if installed improperly engine damage may occur. DISCLAIMER: VTT and ECS are not responsible for any engine damage caused by improper installation, or misuse of the crank hub solution.

Show More Show Less

Ferrea Performance Intake Valve - Stock Size

T#:583445

Part#: F1550P

Back Ordered

$ 34.99 USD

Add to Wish List

Qty

$ 34.99 USD

Add to Wish List

OEM Elring Cylinder Head Bolt Set - E30 E34 M20 2.5L 2.7L

2X Entries For Our G87 M2 Sweepstakes! We Price Match - Give Us A Call or Chat!

T#:2706174

Part#: 11121726478

In Stock

$ 37.99

This product was last offered at the strikethrough price on
07-29-2026

$ 25.99 USD

Add to Wish List

Qty

$ 25.99 USD

Add to Wish List

Brand new set of cylinder head bolts - the cylinder head bolts need to be replaced after removal, once a bolt is torqued down you're unable to reuse it.

Cylinder Head Bolt Kit

2X Entries For Our G87 M2 Sweepstakes! We Price Match - Give Us A Call or Chat!

T#:582581

Part#: 11121721938

In Stock

$ 29.99

This product was last offered at the strikethrough price on
07-23-2026

$ 21.99 USD

Add to Wish List

Qty

$ 21.99 USD

Add to Wish List

Cylinder Head Bolts - Set Of 13

2X Entries For Our G87 M2 Sweepstakes! We Price Match - Give Us A Call or Chat!

T#:591559

Part#: 11127560274

In Stock

$ 32.99

This product was last offered at the strikethrough price on
06-22-2026

$ 32.90 USD

Add to Wish List

Qty

$ 32.90 USD

Add to Wish List

Cylinder Head Bolt Set for Engine Maintenance

When it comes to replacing a head gasket or performing internal engine work, this cylinder head bolt set is a must-have for your project. Ensuring a proper seal and assembly, these bolts are essential for refitting the cylinder head to the engine block. Keep in mind that the old bolts are not reusable, so you'll need this new set for a reliable repair. Additionally, depending on your requirements, you may need a new head gasket with either standard or plus thickness for machined heads. The set includes the following bolts:

10 M10x145 head bolts
2 M8x95 bolts
1 M8x35 bolt

Show More Show Less

Ferrea Performance Exhaust Valve - Stock Size

T#:583444

Part#: F1552P

Ships on Sep 1, 2026

$ 34.99 USD

Add to Wish List

Qty

$ 34.99 USD

Add to Wish List

Elring Cylinder Head Bolt Set

2X Entries For Our G87 M2 Sweepstakes! We Price Match - Give Us A Call or Chat!

T#:377135

Part#: 11127548799

Ships in 6 Business Days

$ 46.99

This product was last offered at the strikethrough price on
07-30-2026

$ 29.99 USD

Add to Wish List

Qty

$ 29.99 USD

Add to Wish List

Head bolts are one time use, and under no circumstance should be reused. Head bolts stretch when torqued, and do not return to a non-stretched state.

Spline N55 S55 Lock Crank Hub Solution W/ Hardware Package

T#:18733531

Part#: VTT-CRANKHUB-5

Ships on Aug 31, 2026

$ 880.99 USD

Add to Wish List

Qty

$ 880.99 USD

Add to Wish List

Under certain conditions, the N55 crank hub likes to spin, without warning and even when the engine is in perfect health. The engineers at Vargas saw and dealt with this problem time and again, and they saw fit to do something about it. This hub uses a proprietary "Spline Lock" technology that uses high tolerance machined splines which press into the crank, and positively lock the hub to the crank. The splines are machined in such a way that rotational forces drive the hub, and splines deeper into the crank meaning when the hub encounters a situation that would normally slip a stock hub the splined hub is driven into the crank to keep it in place (much like a splined extractor). Features: Installs the same as a stock hub Does NOT require the crank to be drilled for pins Manufactured from Harndered 17-4SS We suggest the Crank Hub System ONLY be installed by a qualified shop or technician. Timing tools are 100% REQUIRED if installed improperly engine damage may occur. DISCLAIMER: VTT and ECS are not responsible for any engine damage caused by improper installation, or misuse of the crank hub solution.

Show More Show Less

Elring Cylinder Head Bolt Set - E39, E46, E53

2X Entries For Our G87 M2 Sweepstakes! We Price Match - Give Us A Call or Chat!

T#:377047

Part#: 11121740065

Ships in 1-2 days

$ 43.56

This product was last offered at the strikethrough price on
08-12-2026

$ 34.99 USD

Add to Wish List

Qty

$ 34.99 USD

Add to Wish List

Includes all head bolts in one cylinder head

Valve Stem Seal Kit - Set Of 16 - N12 N14 N16 N18 1.6L Engine ...

2X Entries For Our G87 M2 Sweepstakes! We Price Match - Give Us A Call or Chat!

T#:591737

Part#: 11340033950

In Stock

$ 31.99 USD

Add to Wish List

Qty

$ 31.99 USD

Add to Wish List

Ensure optimal performance of your Mini's N12, N14, N16, or N18 1.6L engine with this Valve Stem Seal Kit. It includes a set of 16 seals recommended for replacement whenever installing new valves. These seals play a crucial role in sealing the valve under the spring, preventing oil leakage and maintaining proper engine function.

Set of 16 valve stem seals for N12, N14, N16, or N18 1.6L engines
Recommended for replacement when installing new valves
Seals the valve under the spring to prevent oil leakage

Show More Show Less

OEM Elring Cylinder Head Bolt Set - N20/26 2.0L

2X Entries For Our G87 M2 Sweepstakes! We Price Match - Give Us A Call or Chat!

T#:2602240

Part#: 11122212157

In Stock at Vendor

$ 75.99

This product was last offered at the strikethrough price on
05-07-2026

$ 73.99 USD

Add to Wish List

Qty

$ 73.99 USD

Add to Wish List

If you remove your cylinder head replacement head bolts are a must. These bolts are designed to be torqued down and not reused.

OEM Elring Cylinder Head Bolt Set - F8X M2 Comp M3 M4 S55 3.0L ...

2X Entries For Our G87 M2 Sweepstakes! We Price Match - Give Us A Call or Chat!

T#:2706168

Part#: 11127853937

In Stock

$ 86.99

This product was last offered at the strikethrough price on
05-07-2026

$ 83.99 USD

Add to Wish List

Qty

$ 83.99 USD

Add to Wish List

If you remove your cylinder head replacement head bolts are a must. These bolts are designed to be torqued down and not reused.

Elring Cylinder Head Bolt Set - E53 E60 E63 E64 E65 E66 E70

2X Entries For Our G87 M2 Sweepstakes! We Price Match - Give Us A Call or Chat!

T#:596415

Part#: 11127583113

In Stock at Vendor

$ 73.99

This product was last offered at the strikethrough price on
05-07-2026

$ 70.99 USD

Add to Wish List

Qty

$ 70.99 USD

Add to Wish List

Spline Lock Crank Hub Solution W/ Crank Bolt Capture - N54

T#:18733527

Part#: VTT-CRANKHUB-2

Ships on Aug 31, 2026

$ 871.99 USD

Add to Wish List

Qty

$ 871.99 USD

Add to Wish List

Anyone with a modified N54 knows the risks involved. Upping the performance of any engine can come with some inherent risk; if we add more boost but not fuel, detonation will occur (or worse). Furthermore, improper installation, maintenance, or operation can turn a perfectly healthy engine into a paperweight. The worst failures, however, are the ones we don't plan for. When the engine simply can't handle the stresses its put under, or the design is such that it simply does not support extreme conditions. Enter the N54 crank hub. Under certain conditions, it likes to spin without warning, even when the engine is in perfect health. The engineers at Vargas saw and dealt with this problem time and again, and they saw fit to do something about it. This hub uses a proprietary "Spline Lock" technology that uses high tolerance machined splines that press into the crank and positively lock the hub to the crank. The splines are machined in such a way that rotational forces drive the hub, and splines deeper into the crank meaning when the hub encounters a situation that would normally slip a stock hub the splined hub is driven into the crank to keep it in place (much like a splined extractor). Vargas spent many months testing, and retesting this design, utilizing well over 10 different samples to come to the final production version. During testing, the final hub managed to break the testing rig before slipping. These have been bench-tested, and real-world tested on the VTT N54 race car spinning 8K RPM, and making well over 900WHP. Features: Installs the same as a stock hub Does NOT require the crank to be drilled for pins Manufactured from Harndered 17-4SS We suggest the Crank Hub System ONLY be installed by a qualified shop or technician. Timing tools are 100% REQUIRED if installed improperly engine damage may occur. DISCLAIMER: VTT and Turner Motorsport are not responsible for any engine damage caused by improper installation, or misuse of the crank hub solution.

Show More Show Less

Spline Lock Crank Hub Solution

T#:8061334

Part#: VTT-N55-CRANKHUB

Ships on Aug 31, 2026

$ 818.99 USD

Add to Wish List

Qty

$ 818.99 USD

Add to Wish List

Under certain conditions, the N55 crank hub likes to spin, without warning and even when the engine is in perfect health. The engineers at Vargas saw and dealt with this problem time and again, and they saw fit to do something about it. This hub uses a proprietary "Spline Lock" technology that uses high tolerance machined splines which press into the crank, and positively lock the hub to the crank. The splines are machined in such a way that rotational forces drive the hub, and splines deeper into the crank meaning when the hub encounters a situation that would normally slip a stock hub the splined hub is driven into the crank to keep it in place (much like a splined extractor). Features: Installs the same as a stock hub Does NOT require the crank to be drilled for pins Manufactured from Harndered 17-4SS We suggest the Crank Hub System ONLY be installed by a qualified shop or technician. Timing tools are 100% REQUIRED if installed improperly engine damage may occur. DISCLAIMER: VTT and ECS are not responsible for any engine damage caused by improper installation, or misuse of the crank hub solution. This hub uses a proprietary "Spline Lock" technology that uses high tolerance machined splines which press into the crank, and positively lock the hub to the crank. The splines are machined in such a way that rotational forces drive the hub, and splines deeper into the crank meaning when the hub encounters a situation that would normally slip a stock hub the splined hub is driven into the crank to keep it in place (much like a splined extractor). Features: Installs the same as a stock hub Does NOT require the crank to be drilled for pins Manufactured from Harndered 17-4SS We suggest the Crank Hub System ONLY be installed by a qualified shop or technician. Timing tools are 100% REQUIRED if installed improperly engine damage may occur. DISCLAIMER: VTT and ECS are not responsible for any engine damage caused by improper installation, or misuse of the crank hub solution. The product comes with a 1-year unlimited mileage warranty from manufacturer defects.

Show More Show Less

Vargas "Spline Lock" Crank Hub Solution - N54

T#:558924

Part#: VTT-N54-CRANKHUB

Ships on Aug 31, 2026

$ 818.99 USD

Add to Wish List

Qty

$ 818.99 USD

Add to Wish List

Anyone with a modified N54 knows the risks involved. Upping the performance of any engine can come with some inherent risk; if we add more boost but not fuel, detonation will occur (or worse). Furthermore, improper installation, maintenance, or operation can turn a perfectly healthy engine into a paperweight. The worst failures, however, are the ones we don't plan for. When the engine simply can't handle the stresses its put under, or the design is such that it simply does not support extreme conditions. Enter the N54 crank hub. Under certain conditions, it likes to spin without warning, even when the engine is in perfect health. The engineers at Vargas saw and dealt with this problem time and again, and they saw fit to do something about it. This hub uses a proprietary "Spline Lock" technology that uses high tolerance machined splines that press into the crank and positively lock the hub to the crank. The splines are machined in such a way that rotational forces drive the hub, and splines deeper into the crank meaning when the hub encounters a situation that would normally slip a stock hub the splined hub is driven into the crank to keep it in place (much like a splined extractor). Vargas spent many months testing, and retesting this design, utilizing well over 10 different samples to come to the final production version. During testing, the final hub managed to break the testing rig before slipping. These have been bench-tested, and real-world tested on the VTT N54 race car spinning 8K RPM, and making well over 900WHP. Features: Installs the same as a stock hub Does NOT require the crank to be drilled for pins Manufactured from Harndered 17-4SS We suggest the Crank Hub System ONLY be installed by a qualified shop or technician. Timing tools are 100% REQUIRED if installed improperly engine damage may occur. DISCLAIMER: VTT and Turner Motorsport are not responsible for any engine damage caused by improper installation, or misuse of the crank hub solution. The worst failures, however, are the ones we don't plan for. When the engine simply can't handle the stresses its put under, or the design is such that it simply does not support extreme conditions. Enter the N54 crank hub. Under certain conditions, it likes to spin without warning, even when the engine is in perfect health. The engineers at Vargas saw and dealt with this problem time and again, and they saw fit to do something about it. This hub uses a proprietary "Spline Lock" technology that uses high tolerance machined splines that press into the crank and positively lock the hub to the crank. The splines are machined in such a way that rotational forces drive the hub, and splines deeper into the crank meaning when the hub encounters a situation that would normally slip a stock hub the splined hub is driven into the crank to keep it in place (much like a splined extractor). Vargas spent many months testing, and retesting this design, utilizing well over 10 different samples to come to the final production version. During testing, the final hub managed to break the testing rig before slipping. These have been bench-tested, and real-world tested on the VTT N54 race car spinning 8K RPM, and making well over 900WHP. Features: Installs the same as a stock hub Does NOT require the crank to be drilled for pins Manufactured from Harndered 17-4SS We suggest the Crank Hub System ONLY be installed by a qualified shop or technician. Timing tools are 100% REQUIRED if installed improperly engine damage may occur. DISCLAIMER: VTT and Turner Motorsport are not responsible for any engine damage caused by improper installation, or misuse of the crank hub solution. The product comes with a 1-year unlimited mileage warranty from manufacturer defects.

Show More Show Less

Spline Lock Crank Hub Solution W/ Hardware Package - N54

T#:18733526

Part#: VTT-CRANKHUB-4

Ships on Aug 31, 2026

$ 880.99 USD

Add to Wish List

Qty

$ 880.99 USD

Add to Wish List

Anyone with a modified N54 knows the risks involved. Upping the performance of any engine can come with some inherent risk; if we add more boost but not fuel, detonation will occur (or worse). Furthermore, improper installation, maintenance, or operation can turn a perfectly healthy engine into a paperweight. The worst failures, however, are the ones we don't plan for. When the engine simply can't handle the stresses its put under, or the design is such that it simply does not support extreme conditions. Enter the N54 crank hub. Under certain conditions, it likes to spin without warning, even when the engine is in perfect health. The engineers at Vargas saw and dealt with this problem time and again, and they saw fit to do something about it. This hub uses a proprietary "Spline Lock" technology that uses high tolerance machined splines that press into the crank and positively lock the hub to the crank. The splines are machined in such a way that rotational forces drive the hub, and splines deeper into the crank meaning when the hub encounters a situation that would normally slip a stock hub the splined hub is driven into the crank to keep it in place (much like a splined extractor). Vargas spent many months testing, and retesting this design, utilizing well over 10 different samples to come to the final production version. During testing, the final hub managed to break the testing rig before slipping. These have been bench-tested, and real-world tested on the VTT N54 race car spinning 8K RPM, and making well over 900WHP. Features: Installs the same as a stock hub Does NOT require the crank to be drilled for pins Manufactured from Harndered 17-4SS We suggest the Crank Hub System ONLY be installed by a qualified shop or technician. Timing tools are 100% REQUIRED if installed improperly engine damage may occur. DISCLAIMER: VTT and Turner Motorsport are not responsible for any engine damage caused by improper installation, or misuse of the crank hub solution.

Show More Show Less

VTT N54 “Spline Lock” CrankHub Solution Package W/ Crank Bolt Cap...

T#:19395579

Part#: VTTCRANKHUBPKG

Ships on Aug 31, 2026

$ 934.99 USD

Add to Wish List

Qty

$ 934.99 USD

Add to Wish List

VTT is proud to offer the only complete N54 complete crank hub solution that does NOT require the crank to be drilled for pins. Our hub uses our proprietary “Spline Lock” technology that uses high tolerance machined splines which press into the crank, and positively lock the hub to the crank. The splines are machined in such a way that rotational forces drive the hub, and splines deeper into the crank meaning when the hub encounters a situation that would normally slip a stock hub the splined hub is driven into the crank to keep it in place (much like a splined extractor). We spent many months testing, and retesting this design, utilizing well over 10 different samples to come to our final production version. During testing, our final hub managed to break our testing rig before slipping. These have been bench tested, and real-world tested on the VTT N54 race car spinning 8K RPM and making well over 900WHP. This technology means our hub installs the same as a stock hub, no drilling of the crank, which means MUCH less labor is involved and is reversible is ever wanting to be uninstalled leaving no holes in the crank. The “Spline Lock” is ONLY available with the VTT Crank bolt capture for the ULTIMATE Crank Hub solution for your BMW. These parts are designed to be used together, and the spline lock should not run without the CBC VTT “Spline Lock” Crank hubs are CNC manufactured from 440C tool Steel with a Rockwell rating of HRC60 for the ultimate in durability, and toughness. Hub Plus OEM bolt OEM Oil pump sprocket OEM oil sprocket retainer VTT Crank bolt capture

Show More Show Less

N54 Spline Lock Crank Hub Solution With Complete Package

T#:18733525

Part#: VTT-CRANKHUB-3

Ships in 6 Business Days

$ 939.99 USD

Add to Wish List

Qty

$ 939.99 USD

Add to Wish List

Anyone with a modified N54 knows the risks involved. Upping the performance of any engine can come with some inherent risk; if we add more boost but not fuel, detonation will occur (or worse). Furthermore, improper installation, maintenance, or operation can turn a perfectly healthy engine into a paperweight. The worst failures, however, are the ones we don't plan for. When the engine simply can't handle the stresses its put under, or the design is such that it simply does not support extreme conditions. Enter the N54 crank hub. Under certain conditions, it likes to spin without warning, even when the engine is in perfect health. The engineers at Vargas saw and dealt with this problem time and again, and they saw fit to do something about it. This hub uses a proprietary "Spline Lock" technology that uses high tolerance machined splines that press into the crank and positively lock the hub to the crank. The splines are machined in such a way that rotational forces drive the hub, and splines deeper into the crank meaning when the hub encounters a situation that would normally slip a stock hub the splined hub is driven into the crank to keep it in place (much like a splined extractor). Vargas spent many months testing, and retesting this design, utilizing well over 10 different samples to come to the final production version. During testing, the final hub managed to break the testing rig before slipping. These have been bench-tested, and real-world tested on the VTT N54 race car spinning 8K RPM, and making well over 900WHP. Features: Installs the same as a stock hub Does NOT require the crank to be drilled for pins Manufactured from Harndered 17-4SS We suggest the Crank Hub System ONLY be installed by a qualified shop or technician. Timing tools are 100% REQUIRED if installed improperly engine damage may occur. DISCLAIMER: VTT and Turner Motorsport are not responsible for any engine damage caused by improper installation, or misuse of the crank hub solution.

Show More Show Less

Cylinder Head Gasket Set MINI N18 1.6L Engine

2X Entries For Our G87 M2 Sweepstakes! We Price Match - Give Us A Call or Chat!

T#:593035

Part#: 456.560

Ships on Sep 2, 2026

$ 245.99 USD

Add to Wish List

Qty

$ 245.99 USD

Add to Wish List

Ensure optimal engine performance for your Mini with this comprehensive Cylinder Head Gasket Set. Perfect for repairing all gaskets and seals during cylinder head replacement or repair, this set includes intake and exhaust gaskets, valve stem seals, valve cover gasket, exhaust gasket, and throttle body gasket. Benefits include:

Comprehensive set for repairing gaskets and seals.
Ensures proper sealing and prevents leaks.
Compatible with Mini models.
Facilitates cylinder head replacement or repair.

Show More Show Less

Elring Cylinder Head Bolt Set - F01 F02 F10 F12 F13 E70 F15 F16 F85 F...

2X Entries For Our G87 M2 Sweepstakes! We Price Match - Give Us A Call or Chat!

T#:596417

Part#: 11127607557

Ships on Sep 2, 2026

$ 83.87 USD

Add to Wish List

Qty

$ 83.87 USD

Add to Wish List

E36 325, 328 M3 Ferrea Spring Seat Set

T#:163

Part#: SL1021-24

Back Ordered

$ 118.80 USD

Add to Wish List

Qty

$ 118.80 USD

Add to Wish List

E36 325, 328 M3 Ferrea Spring Seat Set includes 24 seats. MUST be uses with the Ferrea valve springs. Recommended to be used with the Ferrea Competition Plus Big Valves and Ferrea Titanium Retainers. See links below.

The goal at Ferrea is to create the finest valves and bearings money can buy. With a staggering array of applications for virtually every production engine in existence both gas and diesel Ferrea has the parts you need to finish your next engine project with confidence.

This item fits the following BMWs:
1992-1998 E36 BMW 323is 323ic 325i 325is 325ic 328i 328is 328ic M3
1991-1995 E34 BMW 525i

Show More Show Less

E36 325, 328 M3 Ferrea Titanium Retainer Set

T#:31

Part#: E11025-24

Back Ordered

$ 7,199.76 USD

Add to Wish List

Qty

$ 7,199.76 USD

Add to Wish List

E36 325, 328 M3 Ferrea Titanium Retainer Set - set of 24. Recommended to be used with the Ferrea Competition Plus Big Valves. MUST be used with the Ferrea high-performance valve spring and seat kit. See links below.

The goal at Ferrea is to create the finest valves and bearings money can buy. With a staggering array of applications for virtually every production engine in existence both gas and diesel, Ferrea has the parts you need to finish your next engine project with confidence.

This item fits the following BMWs:
1992-1998 E36 BMW 325i 325is 325ic 328i 328is 328ic M3
1991-1995 E34 BMW 525i

Show More Show Less

E36 325, 328 & M3 Ferrea High Performance Valve Spring Set

T#:439

Part#: S10049-24

Back Ordered

$ 817.20 USD

Add to Wish List

Qty

$ 817.20 USD

Add to Wish List

Ferrea valve springs are developed from high strength alloys, including premium grade chrome silicone steel These springs are manufactured with state-of-the-art equipment. Ferrea springs are heat-treated and stress-relieved, which dramatically increases the spring's life. Strict quality control procedures and cycle testing ensures consistency from batch to batch. Ferrea valve springs provide the stability needed for high lift, high rpm racing and street car engines. Kit includes a set of 24 springs. MUST be used with the Ferrea Spring Seat and Titanium Retainers. See links below.

https://www.turnermotorsport.com/e/p-163-e36-325-328-m3-ferrea-spring-seat-set/

https://www.turnermotorsport.com/e/p-31-e36-325-328-m3-ferrea-titanium-retainer-set/

This item fits the following BMWs:
1992-1998 E36 BMW 323is 323ic 325i 325is 325ic 328i 328is 328ic M3
1991-1995 E34 BMW 525i

Show More Show Less

Lower Timing Case Gasket Set - E39 E38 E32 E34 E53

2X Entries For Our G87 M2 Sweepstakes! We Price Match - Give Us A Call or Chat!

T#:6643

Part#: 11141436978

In Stock

$ 16.99 USD

Add to Wish List

Qty

$ 16.99 USD

Add to Wish List

This kit includes the 3 gaskets for the front lower engine timing chain case for BMW's with the M60 or M62 V-8 engine. Replacing these components is essential when replacing any timing components on your M60/M62 engine.
With more than 100 years in the industry, Elring is one of the oldest names in the European autoparts segment. Delivering OE-quality you can rest assured the job will be done right the first time.

This item fits the following BMWs:
1989-1995 E34 BMW 530i 540i
1997-2003 E39 BMW 540i
1988-1994 E32 BMW 740i 740il
1995-2001 E38 BMW 740i 740il
1990-1999 E31 BMW 840i 840ci
2000-2003 E52 BMW Z8 Alpina Roadster

Show More Show Less

Rocker Shaft Plug - E30 325e 325i, E34 525i - M20 engine

2X Entries For Our G87 M2 Sweepstakes! We Price Match - Give Us A Call or Chat!

T#:14515

Part#: 11331264519

In Stock

$ 2.03 USD

Add to Wish List

Qty

$ 2.03 USD

Add to Wish List

Rocker shaft blind plug for M20 engine. 4 per engine required.

If you drive a European vehicle, chances are high your vehicle came equipped with one or more Victor Reinz gaskets. Choose OE quality VR gaskets and seals and do the job right the first time.

This item fits the following BMWs:
1982-1988 E28 BMW 528e
1984-1991 E30 BMW 325e 325es 325i 325ic 325is 325ix
1989-1990 E34 BMW 525i

Show More Show Less

MINI R55 to R61 Shaft Seal

2X Entries For Our G87 M2 Sweepstakes! We Price Match - Give Us A Call or Chat!

T#:583720

Part#: 11117568264

In Stock

$ 12.99 USD

Add to Wish List

Qty

$ 12.99 USD

Add to Wish List

Enhance your Mini's engine functionality and prevent leaks with this crucial shaft seal. Mounting on both the upper and lower halves of the engine block and situated opposite the transmission side, this seal focuses on the timing chain area, proving its significance for engine repairs and effectively addressing seal leaks.

Key Benefits:

Enhanced engine block sealing for optimal performance
Prevents leaks and ensures sustained engine integrity
Suitable for both upper and lower halves of the engine block
Positioned away from the transmission side
Perfect solution for seal-related issues during engine repairs

Show More Show Less

Osvat Intake Valve - E28, E30, E34

T#:1196099

Part#: 11341706631

In Stock

$ 12.99

This product was last offered at the strikethrough price on
06-22-2026

$ 10.99 USD

Limited Qty Sale

Add to Wish List

Qty

$ 12.99

This product was last offered at the strikethrough price on
06-22-2026

$ 10.99 USD

Limited Qty Sale

Add to Wish List

Standard replacement intake valve

Elring Cylinder Head Bolt Set - F01 F02 F10 F12 F13 E70 E71

2X Entries For Our G87 M2 Sweepstakes! We Price Match - Give Us A Call or Chat!

T#:596414

Part#: 11127582454

Ships in 3 Business Days

$ 143.90 USD

Add to Wish List

Qty

$ 143.90 USD

Add to Wish List

One time use torque-to-yield cylinder head bolts. Always replace as a set whenever cylinder head is removed and reinstalled.

BMW Cylinder Head Bolt Set

2X Entries For Our G87 M2 Sweepstakes! We Price Match - Give Us A Call or Chat!

T#:15412447

Part#: 11121729246

In Stock at Vendor

$ 36.99

This product was last offered at the strikethrough price on
05-08-2026

$ 35.99 USD

Add to Wish List

Qty

$ 35.99 USD

Add to Wish List

The cylinder head bolt is a torque-to-yield bolt, meaning the bolts stretch to ensure proper securing when tightened down. After removal, the bolts cannot return to their pre-stretched state and must be replaced for proper torque. This is a full set and includes 10 cylinder head bolts.

Show More Show Less

Elring CSL Exhaust Valve - E46

2X Entries For Our G87 M2 Sweepstakes! We Price Match - Give Us A Call or Chat!

T#:583284

Part#: 18301711969

In Stock at Vendor

$ 16.66 USD

Add to Wish List

Qty

$ 16.66 USD

Add to Wish List

Exhaust valve with better airflow

Osvat Exhaust Valve - Sold Each - E28, E30, E34

T#:1196100

Part#: 11341708896

In Stock at Vendor

$ 35.98 USD

Add to Wish List

Qty

$ 35.98 USD

Add to Wish List

Replace your worn valves

Intake Valve - Priced Each

T#:596779

Part#: 11341267721

Ships in 4 Business Days

$ 13.99

This product was last offered at the strikethrough price on
05-07-2026

$ 8.99 USD

Add to Wish List

Qty

$ 8.99 USD

Add to Wish List

Replacement intake valve 40.0/6.97MM

OEM Elring Cylinder Head Bolt Set - BMW 335d M57 3.0L

2X Entries For Our G87 M2 Sweepstakes! We Price Match - Give Us A Call or Chat!

T#:2691343

Part#: 11127798532

In Stock at Vendor

$ 97.99

This product was last offered at the strikethrough price on
05-07-2026

$ 95.99 USD

Add to Wish List

Qty

$ 95.99 USD

Add to Wish List

Includes a full set of replacement Head Bolts. Cylinder head bolts need to be replaced after removal, once a bolt is torqued down you are unable to reuse it.

BMW Cylinder Head Bolt Set

2X Entries For Our G87 M2 Sweepstakes! We Price Match - Give Us A Call or Chat!

T#:15247118

Part#: 11127838831

Ships in 3 Business Days

$ 60.99

This product was last offered at the strikethrough price on
05-08-2026

$ 59.99 USD

Add to Wish List

Qty

$ 59.99 USD

Add to Wish List

When replacing a head gasket or performing maintenance that requires the removal of the head, it is advised to replace the cylinder head bolts as they are torque to yield bolts that allow for one time use only.

Show More Show Less

Ferrea High Performance Valve Kit - B58

T#:29035337

Part#: FER-HPVK-B58-T29

Ships in 4 Business Days

$ 929.00 USD

Add to Wish List

Qty

$ 929.00 USD

Add to Wish List

The BMW B58 engine can significantly benefit from the high-performance Ferrea valve kit, featuring the renowned Ferrea Competition Plus Valves. Known as the industry’s most dependable extreme-duty valves, these valves are crafted using special aerospace-grade alloys, including the high tensile strength EV8-Z18. To ensure unparalleled quality, an exclusive two-step slow forging process is utilized, promoting optimal grain flow and minimizing material structure damage. Additionally, the valves undergo a rigorous 48-hour heat treatment and stress-relieving process, crucial for maintaining their molecular integrity. The final touch is the application of avionics-quality hard chrome and a specially hardened tip, ensuring exceptional durability and reliability.

Show More Show Less

Ferrea High Performance Valve Kit - B58

T#:29035336

Part#: FER-HPVK-B58-T28

Ships in 4 Business Days

$ 1,059.99 USD

Add to Wish List

Qty

$ 1,059.99 USD

Add to Wish List

The BMW B58 engine can significantly benefit from the high-performance Ferrea valve kit, featuring the renowned Ferrea Competition Plus Valves. Known as the industry’s most dependable extreme-duty valves, these valves are crafted using special aerospace-grade alloys, including the high tensile strength EV8-Z18. To ensure unparalleled quality, an exclusive two-step slow forging process is utilized, promoting optimal grain flow and minimizing material structure damage. Additionally, the valves undergo a rigorous 48-hour heat treatment and stress-relieving process, crucial for maintaining their molecular integrity. The final touch is the application of avionics-quality hard chrome and a specially hardened tip, ensuring exceptional durability and reliability.

Show More Show Less

Shaft Seal - Front Seal

2X Entries For Our G87 M2 Sweepstakes! We Price Match - Give Us A Call or Chat!

T#:594753

Part#: 11111485171

Ships on Sep 2, 2026

$ 11.99

This product was last offered at the strikethrough price on
08-07-2026

$ 10.99 USD

Add to Wish List

Qty

$ 10.99 USD

Add to Wish List

BMW Cylinder head bolt set

T#:45483601

Part#: 802.700

Special Order: No Guaranteed ETA

$ 42.99 USD

Add to Wish List

Qty

$ 42.99 USD

Add to Wish List

BMW Cylinder Head Bolt - Priced Each - M10 1.8L - Partnumber 11120621144

Elring Cylinder Head Bolt Set - BMW B46/B48 2.0L

T#:44733255

Part#: 794.470

Special Order: No Guaranteed ETA

$ 83.99 USD

Add to Wish List

Qty

$ 83.99 USD

Add to Wish List

Cylinder head bolts feature a torque-to-yield design, meaning that they can only be used once. If you have to pull your cylinder head for any reason, be sure to pick up a set of cylinder head bolts to ensure your head is properly attached to the engine block. This kit includes all 10 replacement cylinder head bolts. Replaces BMW p/n 11128644675.

Show More Show Less

Cylinder Head Bolt - Set Of 14

2X Entries For Our G87 M2 Sweepstakes! We Price Match - Give Us A Call or Chat!

T#:15247124

Part#: 794.480

Special Order: No Guaranteed ETA

$ 88.99 USD

Add to Wish List

Qty

$ 88.99 USD

Add to Wish List

Elring Cylinder Head Bolt Set - BMW N57 B57 3.0L

T#:44767341

Part#: 233.380

Special Order: No Guaranteed ETA

$ 59.99 USD

Add to Wish List

Qty

$ 59.99 USD

Add to Wish List

Cylinder head bolts need to be replaced after removal. Once a bolt is torqued down, you're unable to reuse it. This set of Elring cylinder head bolts is a great option to reattach your head to the block, without paying the markup for Genuine BMW parts. Replaces BMW p/n 11128513130, 11127812925, & 11128511621

Show More Show Less

Elring Cylinder Head Bolt Set - BMW N47 2.0L

T#:45517828

Part#: 233.370

Special Order: No Guaranteed ETA

$ 58.99 USD

Add to Wish List

Qty

$ 58.99 USD

Add to Wish List

BMW cylinder head bolts are almost always stretch bolts and should never be reused after removal. Reusing old bolts can lead to a weak seal between the cylinder head and engine block, allowing the head to lift and cause potentially catastrophic damage. Replace your old cylinder head bolts with these brand new Elring bolts to ensure your head is properly secured to prevent damage and keep your engine healthy. Replaces BMW # 11128513128

Show More Show Less