VTT S55 Crank Bolt Capture - F8X S55 F3x N55

T#:557934

Part#: VTT-S55-CBC

In Stock

$ 129.99 USD

Add to Wish List

Qty

$ 129.99 USD

Add to Wish List

The S55 suffers from a weak point in its crankshaft. It has been reported that when increasing the power to the engine, the crank hub can move or spin slightly under an extreme load.

E46 M3 Schrick DLC-Coated Rocker Arm

T#:342372

Part#: 041513800

In Stock

$ 263.99

This product was last offered at the strikethrough price on
07-07-2026

$ 165.00 USD

Add to Wish List

Qty

$ 165.00 USD

Add to Wish List

The roller rocker arms transfer the rotational force of the camshaft to open the intake and exhaust valves. One end is raised and lowered by the rotating lobe of the camshaft, while the other end acts on the associated valve stem. If a roller rocker arm has failed you may experience a constant ticking noise during engine operation, or alternatively if the rocker arm has broken, you will receive multiple misfires and a rough running engine.

Show More Show Less

Vargas "Spline Lock" Crank Hub Solution - Includes Crank Bolt Capture...

T#:558795

Part#: VTT-CRANKHUB-1

In Stock

$ 889.99 USD

Add to Wish List

Qty

$ 889.99 USD

Add to Wish List

Under certain conditions, the N55 crank hub likes to spin, without warning and even when the engine is in perfect health. The engineers at Vargas saw and dealt with this problem time and again, and they saw fit to do something about it. This hub uses a proprietary "Spline Lock" technology that uses high tolerance machined splines which press into the crank, and positively lock the hub to the crank. The splines are machined in such a way that rotational forces drive the hub, and splines deeper into the crank meaning when the hub encounters a situation that would normally slip a stock hub the splined hub is driven into the crank to keep it in place (much like a splined extractor). Features: Installs the same as a stock hub Does NOT require the crank to be drilled for pins Manufactured from Harndered 17-4SS We suggest the Crank Hub System ONLY be installed by a qualified shop or technician. Timing tools are 100% REQUIRED if installed improperly engine damage may occur. DISCLAIMER: VTT and ECS are not responsible for any engine damage caused by improper installation, or misuse of the crank hub solution.

Show More Show Less

Bav Auto Crankshaft Front Oil Seal Removal / Installer Tool - N54, N5...

T#:580444

Part#: B8800139

Ships on Sep 1, 2026

Sale - Save 5% $ 203.99

This product was last offered at the strikethrough price on
05-03-2026

$ 193.79 USD

Add to Wish List

Qty

Sale - Save 5%

$ 203.99

This product was last offered at the strikethrough price on
05-03-2026

$ 193.79 USD

Add to Wish List

Used in removal and installation of the front crankshaft seal on BMW N55 engines, a common job that you can save yourself a ton of money doing at home.

Spline Lock Crank Hub Solution W/ Complete Package - N55 S55 ...

T#:18733532

Part#: VTT-CRANKHUB-6

Ships in 1 Business Day

$ 986.99

This product was last offered at the strikethrough price on
06-28-2026

$ 939.99 USD

Add to Wish List

Qty

$ 939.99 USD

Add to Wish List

Under certain conditions, the N55 crank hub likes to spin, without warning and even when the engine is in perfect health. The engineers at Vargas saw and dealt with this problem time and again, and they saw fit to do something about it. This hub uses a proprietary "Spline Lock" technology that uses high tolerance machined splines which press into the crank, and positively lock the hub to the crank. The splines are machined in such a way that rotational forces drive the hub, and splines deeper into the crank meaning when the hub encounters a situation that would normally slip a stock hub the splined hub is driven into the crank to keep it in place (much like a splined extractor). Features: Installs the same as a stock hub Does NOT require the crank to be drilled for pins Manufactured from Harndered 17-4SS We suggest the Crank Hub System ONLY be installed by a qualified shop or technician. Timing tools are 100% REQUIRED if installed improperly engine damage may occur. DISCLAIMER: VTT and ECS are not responsible for any engine damage caused by improper installation, or misuse of the crank hub solution.

Show More Show Less

Ferrea Performance Intake Valve - Stock Size

T#:583445

Part#: F1550P

Back Ordered

$ 34.99 USD

Add to Wish List

Qty

$ 34.99 USD

Add to Wish List

Bav Auto Crankshaft Rear Oil Seal Removal / Installer Tool - N51, N52...

T#:580412

Part#: B8800104

In Stock

Sale - Save 5% $ 147.99

This product was last offered at the strikethrough price on
05-03-2026

$ 140.59 USD

Add to Wish List

Qty

Sale - Save 5%

$ 147.99

This product was last offered at the strikethrough price on
05-03-2026

$ 140.59 USD

Add to Wish List

For removal and installation of the rear crankshaft seal on BMW N51, N52 and N54 engines.

Ferrea Performance Exhaust Valve - Stock Size

T#:583444

Part#: F1552P

Ships on Sep 1, 2026

$ 34.99 USD

Add to Wish List

Qty

$ 34.99 USD

Add to Wish List

Bav Auto Intermediate Lever Valve Spring Compressor - N20/26 N55 ...

T#:580431

Part#: B8800124

Ships on Sep 1, 2026

Sale - Save 15% $ 178.99

This product was last offered at the strikethrough price on
05-03-2026

$ 152.14 USD

Add to Wish List

Qty

Sale - Save 15%

$ 178.99

This product was last offered at the strikethrough price on
05-03-2026

$ 152.14 USD

Add to Wish List

For installation and removal of pressure springs on intermediate levers of valve train. Ensures quick, easy and safe handling of these high force springs.

Spline N55 S55 Lock Crank Hub Solution W/ Hardware Package

T#:18733531

Part#: VTT-CRANKHUB-5

Ships in 10 Business Days

$ 880.99 USD

Add to Wish List

Qty

$ 880.99 USD

Add to Wish List

Under certain conditions, the N55 crank hub likes to spin, without warning and even when the engine is in perfect health. The engineers at Vargas saw and dealt with this problem time and again, and they saw fit to do something about it. This hub uses a proprietary "Spline Lock" technology that uses high tolerance machined splines which press into the crank, and positively lock the hub to the crank. The splines are machined in such a way that rotational forces drive the hub, and splines deeper into the crank meaning when the hub encounters a situation that would normally slip a stock hub the splined hub is driven into the crank to keep it in place (much like a splined extractor). Features: Installs the same as a stock hub Does NOT require the crank to be drilled for pins Manufactured from Harndered 17-4SS We suggest the Crank Hub System ONLY be installed by a qualified shop or technician. Timing tools are 100% REQUIRED if installed improperly engine damage may occur. DISCLAIMER: VTT and ECS are not responsible for any engine damage caused by improper installation, or misuse of the crank hub solution.

Show More Show Less

Bavarian Autosport Crankshaft Holding Tool - BMW

T#:580450

Part#: B8800145

In Stock

Sale - Save 15% $ 77.99

This product was last offered at the strikethrough price on
05-03-2026

$ 66.29 USD

Add to Wish List

Qty

Sale - Save 15%

$ 77.99

This product was last offered at the strikethrough price on
05-03-2026

$ 66.29 USD

Add to Wish List

Makes removal of crankshaft hub nut/bolt much easier. A must-have for replacing timing chains, oil pump chains, leaking crankshaft seals and more.

Bav Auto Crankshaft Pulley Holding Tool

T#:580404

Part#: B8800094

In Stock

Sale - Save 10% $ 180.99

This product was last offered at the strikethrough price on
05-03-2026

$ 162.89 USD

Add to Wish List

Qty

Sale - Save 10%

$ 180.99

This product was last offered at the strikethrough price on
05-03-2026

$ 162.89 USD

Add to Wish List

Bav Auto's Crankshaft Pulley Holding Tool enables you to remove your crankshaft nut/bolt with ease - we recommend this tool if you intend on replacing timing chains, oil pump chains, leaking crankshaft seals, etc.

Show More Show Less

Sneed4Speed Street Series Piston Set Of 4 - N18 Stock Size 77mm ...

T#:7260311

Part#: 1828344

Ships in 1 Business Day

$ 425.00 USD

Add to Wish List

Qty

$ 425.00 USD

Add to Wish List

Sneed4Speed Street Series Cast Piston Set – N18 "STD" will be printed on the pistons. Please inspect before install. Built for MINI Cooper S (2011–2016) and JCW (2013–2016), this complete piston set is a direct-fit upgrade for your turbocharged N18 engine. Each kit includes pistons, wrist pins, and a full ring set pre-installed for easy assembly. Every piston comes with a 3-ring configuration: a top and second compression ring plus a multi-piece oil control ring (two thin rails with a wavy expander in between). The rings arrive already installed on the pistons, saving you setup time and ensuring proper fitment. Engineered from high-quality cast aluminum, these pistons are designed to safely handle 18–20 PSI of boost on a tuned setup—perfect for street-driven builds looking for reliable performance without stepping up to forged internals.

Show More Show Less

R56 Main Stud Kit

T#:30397432

Part#: R56MSK

Ships in 2 Business Days

$ 159.99 USD

Add to Wish List

Qty

$ 159.99 USD

Add to Wish List

MAHLE Forged Piston Kit 84mm - N54 - 3.0L

T#:2928970

Part#: 197832209

Back Ordered

$ 1,088.99 USD

Add to Wish List

Qty

$ 1,088.99 USD

Add to Wish List

Forged, 2618. Phosphate + Grafal + Hard Anodized top ring groove + TBC

Sneed4Speed R56 MINI Engine Rod Bearing - Standard Size - N14 / N16 /...

T#:14551946

Part#: NSRBS

In Stock

$ 83.99 USD

Add to Wish List

Qty

$ 83.99 USD

Add to Wish List

Sneed4Speed R56 Mini Engine Rod Bearing for N14, N16, N18 1.6L Engine

Upgrade your Mini's engine performance with Sneed4Speed's R56 Mini Engine Rod Bearing, tailored specifically for N14, N16, N18 1.6L engines. Crafted from top-grade materials, these bearings guarantee exceptional performance and durability.

Optimized for N14, N16, N18 1.6L engines
Enhances overall engine performance
Durable construction for long-lasting reliability
Precision engineering ensures a perfect fit

Show More Show Less

Schrick Intake Camshaft - E46 M3, MZ3, MZ4 (S54) - 288 Degree, 12.5mm...

T#:3572

Part#: TMS3572

Ships on Dec 3, 2026

$ 1,775.98 USD

Add to Wish List

Qty

$ 1,775.98 USD

Add to Wish List

E46 M3 Schrick 288 Degree Intake Camshaft with 12.5mm valve lift. Originally desinged for the M3 CSL but works great in a standard M3. A new rocker arm is required (Schrick or new BMW part #11337833259). This is a more agressive cam that the Schrick 280 degree cam that we also offer for the E46M3

BMW Schrick Technical Specs

Schrick Technical Information / Specs

This item fits the following BMWs:
2001-2006 E46 BMW M3
2001-2002 Z3 BMW M Roadster M Coupe
2006-2008 E85 BMW Z4 M Roadster M Coupe

Show More Show Less

Schrick Exhaust Camshaft - E46 M3, MZ3, MZ4 (S54) - 272 Degree, 12.5m...

T#:11749

Part#: TMS11749

Ships on Dec 3, 2026

$ 824.99 USD

Add to Wish List

Qty

$ 824.99 USD

Add to Wish List

E46 M3 Schrick 272 Degree Exhaust Camshaft with 12.5mm valve lift. New rocker arms are required (BMW part #11337833259 or a new Schrick part).

BMW Schrick Technical Specs

Schrick Technical Information / Specs

This item fits the following BMWs:
2001-2006 E46 BMW M3
2001-2002 Z3 BMW M Roadster M Coupe
2006-2008 E85 BMW Z4 M Roadster M Coupe

Show More Show Less

Schrick Intake Camshaft - E46 M3, MZ3, MZ4 (S54) - 280 Degree, 12.5mm...

T#:11748

Part#: TMS11748

Ships on Dec 3, 2026

$ 1,867.99 USD

Add to Wish List

Qty

$ 1,867.99 USD

Add to Wish List

E46 M3 with S54 engine Schrick 280 Degree Intake Camshaft with 12.5mm valve lift. A new rocker arm is required (Schrick or new BMW part #11337833259).

Schrick Technical Information / Specs

This item fits the following BMWs:
2001-2006 E46 BMW M3
2001-2002 Z3 BMW M Roadster M Coupe
2006-2008 E85 BMW Z4 M Roadster M Coupe

Show More Show Less

Schrick Camshaft - M20 288 degree

T#:3501

Part#: 05601880-00

Ships on Dec 3, 2026

$ 490.00 USD

Add to Wish List

Qty

$ 490.00 USD

Add to Wish List

SEE T#338236

MAHLE PowerPak Piston Kit - 82mm - 10.5:1 CR - B58 3.0L

T#:2929001

Part#: 197883929

Back Ordered

$ 1,275.99 USD

Add to Wish List

Qty

$ 1,275.99 USD

Add to Wish List

Forged, 2618. Get the performance and reliability your B58 needs with MAHLE Motorsports PowerPak Piston Kit. Replacing the weaker factory cast aluminum pistons with the strength and durability of a forged piston.

Show More Show Less

Schrick Performance Camshaft Set - 238/272 - F80 M3, F82/83 M4 S55 ...

T#:637691

Part#: SCHCSSS55238/272

Back Ordered

$ 1,899.99 USD

Add to Wish List

Qty

$ 1,899.99 USD

Add to Wish List

High-performance camshafts are key to increasing the top-end power output of your S55 engine at high boost. 238/272 degree, 10.6mm/10.5mm lift. Perfectly compatible with OE valves, springs, VANOS, Valvetronic etc

Show More Show Less

BMW S65 4.0L MAHLE Forged Piston Kit 92mm

T#:2928987

Part#: 197843622

In Stock

$ 1,429.99 USD

Add to Wish List

Qty

$ 1,429.99 USD

Add to Wish List

Forged, 4032. Get the performance and reliability your S65 needs with MAHLE Motorsports PowerPak Piston Kit. Replacing the weaker factory cast aluminum pistons with the strength and durability of a forged piston.

Show More Show Less

Schrick Exhaust Camshaft - E46 M3, MZ3, MZ4 (S54) - 280 Degree, 12.5m...

T#:1259

Part#: TMS1259

In Stock

Sale - Save 5% $ 1,775.98

This product was last offered at the strikethrough price on
07-07-2026

$ 1,687.18 USD

Add to Wish List

Qty

Sale - Save 5%

$ 1,775.98

This product was last offered at the strikethrough price on
07-07-2026

$ 1,687.18 USD

Add to Wish List

E46 M3 Schrick 280 Degree Exhaust Camshaft with 12.5mm lift. This was originally desinged for the M3 CSL but works great in the standard M3. This cam is slightly more agressive than the "original" Schrick 272 degree (which we also offer). A new rocker arm is required (Schrick or new BMW part #11337833259).

BMW Schrick Technical Specs

Schrick Technical Information / Specs

This item fits the following BMWs:
2001-2006 E46 BMW M3
2001-2002 Z3 BMW M Roadster M Coupe
2006-2008 E85 BMW Z4 M Roadster M Coupe

Show More Show Less

MINI R55+ Sneed4Speed N Series Engine Cylinder Head Bolts Kit ...

T#:18965470

Part#: NSHBS

Ships in 7 Business Days

$ 74.99 USD

Add to Wish List

Qty

$ 74.99 USD

Add to Wish List

MINI R55+ Sneed4Speed N Series Engine Cylinder Head Bolts Kit

Upgrade your MINI's engine with the MINI R55+ Sneed4Speed N Series Engine Cylinder Head Bolts Kit. Engineered for performance and durability, this kit includes high-quality cylinder head bolts designed specifically for N series engines. Ensure a secure and reliable seal for your cylinder head with this premium bolt kit from Sneed4Speed.

Specifically designed for MINI R55+ models
High-quality bolts ensure secure cylinder head seal
Engineered for performance and durability
Provides peace of mind for engine reliability
Easy installation for hassle-free upgrade

Show More Show Less

Schrick Exhaust Camshaft - E46 M3, MZ3, MZ4 (S54) - 280 Degree, 12.5m...

T#:338216

Part#: TMS1259

Ships on Dec 3, 2026

Starting at $ 2,432.99 USD

Add to Wish List

Starting at $ 2,432.99 USD

Add to Wish List

E46 M3 Schrick 280 Degree Exhaust Camshaft with 12.5mm lift. This was originally desinged for the M3 CSL but works great in the standard M3. This cam is slightly more agressive than the "original" Schrick 272 degree (which we also offer). A new rocker arm is required (Schrick or new BMW part #11337833259).

BMW Schrick Technical Specs

Schrick Technical Information / Specs

This item fits the following BMWs:
2001-2006 E46 BMW M3
2001-2002 Z3 BMW M Roadster M Coupe
2006-2008 E85 BMW Z4 M Roadster M Coupe

Show More Show Less

SNEED4SPEED Forged Connection Rods - Set Of 4 R50/R52/R53 W10 W11 1.6...

T#:26238455

Part#: R53S4SROD

Ships in 3 Business Days

$ 449.99 USD

Add to Wish List

Qty

$ 449.99 USD

Add to Wish List

Upgrade your Mini's engine with Sneed4Speed Forged H Beam Connecting Rods, designed for the R53 and R52 Supercharged engines, also compatible with the R50/R52 Base Engines. Crafted from 4340 forged steel, these rods are rated to handle up to 700 horsepower, making them ideal for high-power builds. Perfect for budget-conscious builders seeking reliable performance, these rods offer a direct fit and replacement solution. Backed by a 100-year warranty, they provide peace of mind and long-lasting durability. Each rod includes 180,000 psi rated chrome moly rod bolts, capable of supporting up to 1000 HP.

Designed for R53 and R52 Supercharged engines, compatible with R50/R52 Base Engines
Constructed from 4340 forged steel for strength and durability
Rated to handle up to 700 horsepower for high-power builds
Ideal for budget-conscious builders seeking reliable performance
Direct fit and replacement for easy installation
Backed by a 100-year warranty for long-lasting peace of mind
Includes 180,000 psi rated chrome moly rod bolts for added strength and support

Show More Show Less

BMW US S50 6 Cyl. 284-Degree - Intake Camshaft

T#:554296

Part#: 0284E1840-0V1

In Stock

Sale - Save 15% $ 1,727.99

This product was last offered at the strikethrough price on
07-07-2026

$ 1,468.79 USD

Add to Wish List

Qty

Sale - Save 15%

$ 1,727.99

This product was last offered at the strikethrough price on
07-07-2026

$ 1,468.79 USD

Add to Wish List

Schrick has been dedicated to engine performance through the development of only the highest-quality camshafts for more than 40 years. They've created a bond with BMW enthusiasts nearly the entire time, offering options for both the street and track using top materials for strength and accuracy. Schrick has grown into a technology center offering one of the most advanced locations for engine testing and manufacturing. These are the same cams used by many high-end German tuners who are achieving sizeable gains with the US S50 engine. For the power-hungry, these cams are a great way to achieve a linear increase in horsepower from mid-range, up to redline. Duration Intake- 284 Duration Intake @ 1mm - 253 Intake Peak Timing - 122 Cam Lobe Lift Intake - 11, 9 Valve Lift w/o Valve Clearance Intake - 11, 9 Valve Clearance Intake - 0,25

Show More Show Less

Sneed4Speed Street Series Piston Set Of 4 - N14 Plus Size 77.25mm (+0...

T#:7260305

Part#: 182834325

Special Order: No Guaranteed ETA

$ 425.00 USD

Add to Wish List

Qty

$ 425.00 USD

Add to Wish List

"0.25" will be printed on the pistons. Please inspect before install.

R56 N12 Sneed4Speed Street Series Piston (+0.50)

T#:26238483

Part#: N12PS.5

Ships in 9 Business Days

$ 425.00 USD

Add to Wish List

Qty

$ 425.00 USD

Add to Wish List

"0.50" will be printed on the pistons. Please inspect before install.

Enhance your Mini's engine performance with the R56 N12 Sneed4Speed Street Series Piston (+0.50). This piston set includes a complete ring set, providing everything needed for installation. Each piston features three rings: a top compression ring, a second compression ring, and an oil control ring. The oil control ring is composed of three individual rings, including two thin rings and one wavy metal ring, all installed into a single ring groove on the piston. The pistons come pre-installed with the rings, ensuring a hassle-free installation process.

Street Series Piston designed for R56 N12 engines
Includes a complete ring set for convenience
Three rings per piston: top compression ring, second compression ring, and oil control ring
Oil control ring consists of two thin rings and one wavy metal ring
Pistons come pre-installed with rings for easy installation

Show More Show Less

Vargas "Spline Lock" Crank Hub Solution - N54

T#:558924

Part#: VTT-N54-CRANKHUB

Ships in 10 Business Days

$ 818.99 USD

Add to Wish List

Qty

$ 818.99 USD

Add to Wish List

Anyone with a modified N54 knows the risks involved. Upping the performance of any engine can come with some inherent risk; if we add more boost but not fuel, detonation will occur (or worse). Furthermore, improper installation, maintenance, or operation can turn a perfectly healthy engine into a paperweight. The worst failures, however, are the ones we don't plan for. When the engine simply can't handle the stresses its put under, or the design is such that it simply does not support extreme conditions. Enter the N54 crank hub. Under certain conditions, it likes to spin without warning, even when the engine is in perfect health. The engineers at Vargas saw and dealt with this problem time and again, and they saw fit to do something about it. This hub uses a proprietary "Spline Lock" technology that uses high tolerance machined splines that press into the crank and positively lock the hub to the crank. The splines are machined in such a way that rotational forces drive the hub, and splines deeper into the crank meaning when the hub encounters a situation that would normally slip a stock hub the splined hub is driven into the crank to keep it in place (much like a splined extractor). Vargas spent many months testing, and retesting this design, utilizing well over 10 different samples to come to the final production version. During testing, the final hub managed to break the testing rig before slipping. These have been bench-tested, and real-world tested on the VTT N54 race car spinning 8K RPM, and making well over 900WHP. Features: Installs the same as a stock hub Does NOT require the crank to be drilled for pins Manufactured from Harndered 17-4SS We suggest the Crank Hub System ONLY be installed by a qualified shop or technician. Timing tools are 100% REQUIRED if installed improperly engine damage may occur. DISCLAIMER: VTT and Turner Motorsport are not responsible for any engine damage caused by improper installation, or misuse of the crank hub solution. The worst failures, however, are the ones we don't plan for. When the engine simply can't handle the stresses its put under, or the design is such that it simply does not support extreme conditions. Enter the N54 crank hub. Under certain conditions, it likes to spin without warning, even when the engine is in perfect health. The engineers at Vargas saw and dealt with this problem time and again, and they saw fit to do something about it. This hub uses a proprietary "Spline Lock" technology that uses high tolerance machined splines that press into the crank and positively lock the hub to the crank. The splines are machined in such a way that rotational forces drive the hub, and splines deeper into the crank meaning when the hub encounters a situation that would normally slip a stock hub the splined hub is driven into the crank to keep it in place (much like a splined extractor). Vargas spent many months testing, and retesting this design, utilizing well over 10 different samples to come to the final production version. During testing, the final hub managed to break the testing rig before slipping. These have been bench-tested, and real-world tested on the VTT N54 race car spinning 8K RPM, and making well over 900WHP. Features: Installs the same as a stock hub Does NOT require the crank to be drilled for pins Manufactured from Harndered 17-4SS We suggest the Crank Hub System ONLY be installed by a qualified shop or technician. Timing tools are 100% REQUIRED if installed improperly engine damage may occur. DISCLAIMER: VTT and Turner Motorsport are not responsible for any engine damage caused by improper installation, or misuse of the crank hub solution. The product comes with a 1-year unlimited mileage warranty from manufacturer defects.

Show More Show Less

MAHLE PowerPak Piston Kit 92.50mm - S85 - 5.0L

T#:2928993

Part#: 197859542

Ships in 2 Business Days

$ 1,787.99 USD

Add to Wish List

Qty

$ 1,787.99 USD

Add to Wish List

Forged, 4032. Get the performance and reliability your S85 needs with MAHLE Motorsports PowerPak Piston Kit. Replacing the weaker factory cast aluminum pistons with the strength and durability of a forged piston.

Show More Show Less

MINI R56 N14 Street Series Piston Set Of 4 - Plus Size 77.50mm (+0.50...

T#:7260306

Part#: 182834350

Ships on Sep 1, 2026

$ 425.00 USD

Add to Wish List

Qty

$ 425.00 USD

Add to Wish List

"0.50" will be printed on the pistons. Please inspect before install.

MAHLE Forged Piston Set 87mm - S54 - 3.2L

T#:2958764

Part#: 930286125

Back Ordered

$ 1,088.99 USD

Add to Wish List

Qty

$ 1,088.99 USD

Add to Wish List

Forged, 2618. Get the performance and reliability your S54 needs with MAHLE Motorsports PowerPak Piston Kit. Replacing the weaker factory cast aluminum pistons with the strength and durability of a forged piston.

Show More Show Less

MINI N14 N18 1.6L SNEED4SPEED Stock Connection Rods - Set Of 4 R55/R5...

T#:15943313

Part#: N14RODOEM

Ships in 1 Business Day

$ 249.99 USD

Add to Wish List

Qty

$ 249.99 USD

Add to Wish List

MINI N14 N18 1.6L SNEED4SPEED Stock Connection Rods

A reliable upgrade for Mini vehicles, enhancing engine performance and durability. Engineered with precision and quality materials, these stock connection rods ensure optimal power delivery and longevity for the N14 and N18 1.6L engines.

Provides improved strength and durability over stock rods
Enhances engine performance for a more exhilarating driving experience
Precision engineering ensures perfect fit and compatibility with Mini vehicles
Designed for easy installation with no modifications required

Show More Show Less

MINI R56 N18 Street Series Piston Set Of 4 - Plus Size 77.50mm (+0.50...

T#:7260314

Part#: 182834450

In Stock at Vendor

$ 425.00 USD

Add to Wish List

Qty

$ 425.00 USD

Add to Wish List

"0.50" will be printed on the pistons. Please inspect before install.

MINI R56 N18 Street Series Piston Set Of 4 - Plus Size 77.50mm (+0.50) is a high-performance upgrade designed to enhance engine performance and reliability. This set includes four pistons with a complete ring set pre-installed.

Enhanced Performance: Designed to increase engine displacement with a plus size of 77.50mm (+0.50), improving overall power and efficiency.
Complete Ring Set: Each piston comes with three rings: a top compression ring, a second compression ring, and an oil control ring. The oil control ring is made up of three individual rings (two thin rings and one wavy metal ring) all installed in a single groove.
Pre-installed Rings: Pistons come with the rings already installed, reducing installation time and complexity.
Durable Construction: Crafted as cast pistons for reliable performance under street conditions.

Show More Show Less

Sneed4Speed Street Series Piston Rings Set - Stock Size 77.25mm (+0.2...

T#:18932315

Part#: NSRS.25

Ships in 2 Business Days

$ 24.99 USD

Add to Wish List

Qty

$ 24.99 USD

Add to Wish List

SNEED4SPEED R55/R56/R57/R58/R59/R60/R61 Forged Connection Rods - Set ...

T#:15943314

Part#: R56S4SROD

Ships in 9 Business Days

$ 599.99 USD

Add to Wish List

Qty

$ 599.99 USD

Add to Wish List

Sneed4Speed proudly presents their Forged H Beam Connecting Rods, tailored to fit R56, R55, R57, R58, R59, R60, and R61 MINIs equipped with the N14 and N18 engines. Crafted from resilient 4340 forged steel, these connecting rods are built to withstand the demands of high-performance engines, boasting a remarkable 700 horsepower rating. This makes them a superb choice for budget-conscious builders aiming to achieve significant power gains.

What sets these connecting rods apart is their direct fit and replacement design, ensuring a straightforward installation process for MINI enthusiasts. But that's not all – these rods come backed by an extraordinary 100-year warranty, providing unparalleled peace of mind to vehicle owners.

Furthermore, the kit includes high-quality chrome moly rod bolts, rated at an impressive 180,000 psi, capable of supporting up to 1000 horsepower. Elevate your MINI's performance and reliability with Sneed4Speed's Forged H Beam Connecting Rods.

Show More Show Less

Spline Lock Crank Hub Solution

T#:8061334

Part#: VTT-N55-CRANKHUB

Ships in 10 Business Days

$ 818.99 USD

Add to Wish List

Qty

$ 818.99 USD

Add to Wish List

Under certain conditions, the N55 crank hub likes to spin, without warning and even when the engine is in perfect health. The engineers at Vargas saw and dealt with this problem time and again, and they saw fit to do something about it. This hub uses a proprietary "Spline Lock" technology that uses high tolerance machined splines which press into the crank, and positively lock the hub to the crank. The splines are machined in such a way that rotational forces drive the hub, and splines deeper into the crank meaning when the hub encounters a situation that would normally slip a stock hub the splined hub is driven into the crank to keep it in place (much like a splined extractor). Features: Installs the same as a stock hub Does NOT require the crank to be drilled for pins Manufactured from Harndered 17-4SS We suggest the Crank Hub System ONLY be installed by a qualified shop or technician. Timing tools are 100% REQUIRED if installed improperly engine damage may occur. DISCLAIMER: VTT and ECS are not responsible for any engine damage caused by improper installation, or misuse of the crank hub solution. This hub uses a proprietary "Spline Lock" technology that uses high tolerance machined splines which press into the crank, and positively lock the hub to the crank. The splines are machined in such a way that rotational forces drive the hub, and splines deeper into the crank meaning when the hub encounters a situation that would normally slip a stock hub the splined hub is driven into the crank to keep it in place (much like a splined extractor). Features: Installs the same as a stock hub Does NOT require the crank to be drilled for pins Manufactured from Harndered 17-4SS We suggest the Crank Hub System ONLY be installed by a qualified shop or technician. Timing tools are 100% REQUIRED if installed improperly engine damage may occur. DISCLAIMER: VTT and ECS are not responsible for any engine damage caused by improper installation, or misuse of the crank hub solution. The product comes with a 1-year unlimited mileage warranty from manufacturer defects.

Show More Show Less

MAHLE PowerPak Piston Kit 87.50mm - S54 - 3.2L

T#:2929003

Part#: 930000045

Ships in 2 Business Days

$ 1,088.99 USD

Add to Wish List

Qty

$ 1,088.99 USD

Add to Wish List

Forged, 2618. Get the performance and reliability your S54 needs with MAHLE Motorsports PowerPak Piston Kit. Replacing the weaker factory cast aluminum pistons with the strength and durability of a forged piston.

Show More Show Less

Spline Lock Crank Hub Solution W/ Crank Bolt Capture - N54

T#:18733527

Part#: VTT-CRANKHUB-2

Ships in 10 Business Days

$ 871.99 USD

Add to Wish List

Qty

$ 871.99 USD

Add to Wish List

Anyone with a modified N54 knows the risks involved. Upping the performance of any engine can come with some inherent risk; if we add more boost but not fuel, detonation will occur (or worse). Furthermore, improper installation, maintenance, or operation can turn a perfectly healthy engine into a paperweight. The worst failures, however, are the ones we don't plan for. When the engine simply can't handle the stresses its put under, or the design is such that it simply does not support extreme conditions. Enter the N54 crank hub. Under certain conditions, it likes to spin without warning, even when the engine is in perfect health. The engineers at Vargas saw and dealt with this problem time and again, and they saw fit to do something about it. This hub uses a proprietary "Spline Lock" technology that uses high tolerance machined splines that press into the crank and positively lock the hub to the crank. The splines are machined in such a way that rotational forces drive the hub, and splines deeper into the crank meaning when the hub encounters a situation that would normally slip a stock hub the splined hub is driven into the crank to keep it in place (much like a splined extractor). Vargas spent many months testing, and retesting this design, utilizing well over 10 different samples to come to the final production version. During testing, the final hub managed to break the testing rig before slipping. These have been bench-tested, and real-world tested on the VTT N54 race car spinning 8K RPM, and making well over 900WHP. Features: Installs the same as a stock hub Does NOT require the crank to be drilled for pins Manufactured from Harndered 17-4SS We suggest the Crank Hub System ONLY be installed by a qualified shop or technician. Timing tools are 100% REQUIRED if installed improperly engine damage may occur. DISCLAIMER: VTT and Turner Motorsport are not responsible for any engine damage caused by improper installation, or misuse of the crank hub solution.

Show More Show Less

Spline Lock Crank Hub Solution W/ Hardware Package - N54

T#:18733526

Part#: VTT-CRANKHUB-4

Ships in 10 Business Days

$ 880.99 USD

Add to Wish List

Qty

$ 880.99 USD

Add to Wish List

Anyone with a modified N54 knows the risks involved. Upping the performance of any engine can come with some inherent risk; if we add more boost but not fuel, detonation will occur (or worse). Furthermore, improper installation, maintenance, or operation can turn a perfectly healthy engine into a paperweight. The worst failures, however, are the ones we don't plan for. When the engine simply can't handle the stresses its put under, or the design is such that it simply does not support extreme conditions. Enter the N54 crank hub. Under certain conditions, it likes to spin without warning, even when the engine is in perfect health. The engineers at Vargas saw and dealt with this problem time and again, and they saw fit to do something about it. This hub uses a proprietary "Spline Lock" technology that uses high tolerance machined splines that press into the crank and positively lock the hub to the crank. The splines are machined in such a way that rotational forces drive the hub, and splines deeper into the crank meaning when the hub encounters a situation that would normally slip a stock hub the splined hub is driven into the crank to keep it in place (much like a splined extractor). Vargas spent many months testing, and retesting this design, utilizing well over 10 different samples to come to the final production version. During testing, the final hub managed to break the testing rig before slipping. These have been bench-tested, and real-world tested on the VTT N54 race car spinning 8K RPM, and making well over 900WHP. Features: Installs the same as a stock hub Does NOT require the crank to be drilled for pins Manufactured from Harndered 17-4SS We suggest the Crank Hub System ONLY be installed by a qualified shop or technician. Timing tools are 100% REQUIRED if installed improperly engine damage may occur. DISCLAIMER: VTT and Turner Motorsport are not responsible for any engine damage caused by improper installation, or misuse of the crank hub solution.

Show More Show Less

MAHLE PowerPak Piston Kit 92.00mm - S85 - 5.0L

T#:2928992

Part#: 197859522

Ships in 2 Business Days

$ 1,787.99 USD

Add to Wish List

Qty

$ 1,787.99 USD

Add to Wish List

Forged, 4032. Get the performance and reliability your S65 needs with MAHLE Motorsports PowerPak Piston Kit. Replacing the weaker factory cast aluminum pistons with the strength and durability of a forged piston.

Show More Show Less

BMW N54 3.0L MAHLE Forged Piston Kit 84.50mm

T#:2928972

Part#: 197832225

Back Ordered

$ 1,088.99 USD

Add to Wish List

Qty

$ 1,088.99 USD

Add to Wish List

BMW N54 3.0L MAHLE Forged Piston Kit 84.50mm delivers exceptional performance and reliability for BMW engines. This high-quality piston kit is designed to replace the weaker factory cast aluminum pistons with robust forged pistons, enhancing durability and heat tolerance for extreme engine conditions.

Enhanced Strength: Forged from 2618 aluminum, these pistons are more resistant to extreme heat, detonation, and high pressure, providing superior performance.
Precision Specifications:
- Bore: 84.50mm
- Stroke: 89.6mm
- Rod: 145.05mm
- CH: 31.7mm
- Piston Style: Dish with 4 valve reliefs
- Crown Volume: 17.2cc
- Piston Mass: 314g
- Pin Diameter: 22mm
- Pin Style: Floating
Complete Kit: Includes pistons, pins, clips, and rings (1.0mm, 1.2mm, 2.8mm thickness).
Durable Coatings: Features phosphate, Grafal, and hard anodized top ring groove for added longevity.
Sold as a Set: Comes as a set of 6 pistons.

MAHLE Motorsport's PowerPak and PowerPak+ piston kits are engineered for both high-performance and everyday driving, offering a reliable upgrade for BMW engines. With over 95 years of performance experience, MAHLE Motorsport provides advanced features and superior quality for your engine build.

Show More Show Less

MAHLE PowerPak Piston Kit 92.50mm - S65 - 4.0L

T#:2928989

Part#: 197843642

Ships in 2 Business Days

$ 1,429.99 USD

Add to Wish List

Qty

$ 1,429.99 USD

Add to Wish List

Forged, 4032. Get the performance and reliability your S65 needs with MAHLE Motorsports PowerPak Piston Kit. Replacing the weaker factory cast aluminum pistons with the strength and durability of a forged piston.

Show More Show Less

Sneed4Speed R56 MINI Engine Rod Bearing - Standard Size - Black Magic...

T#:46237922

Part#: NSRBSBM

Ships in 7 Business Days

$ 133.99 USD

Add to Wish List

Qty

$ 133.99 USD

Add to Wish List

VTT N54 “Spline Lock” CrankHub Solution Package W/ Crank Bolt Cap...

T#:19395579

Part#: VTTCRANKHUBPKG

Ships in 10 Business Days

$ 934.99 USD

Add to Wish List

Qty

$ 934.99 USD

Add to Wish List

VTT is proud to offer the only complete N54 complete crank hub solution that does NOT require the crank to be drilled for pins. Our hub uses our proprietary “Spline Lock” technology that uses high tolerance machined splines which press into the crank, and positively lock the hub to the crank. The splines are machined in such a way that rotational forces drive the hub, and splines deeper into the crank meaning when the hub encounters a situation that would normally slip a stock hub the splined hub is driven into the crank to keep it in place (much like a splined extractor). We spent many months testing, and retesting this design, utilizing well over 10 different samples to come to our final production version. During testing, our final hub managed to break our testing rig before slipping. These have been bench tested, and real-world tested on the VTT N54 race car spinning 8K RPM and making well over 900WHP. This technology means our hub installs the same as a stock hub, no drilling of the crank, which means MUCH less labor is involved and is reversible is ever wanting to be uninstalled leaving no holes in the crank. The “Spline Lock” is ONLY available with the VTT Crank bolt capture for the ULTIMATE Crank Hub solution for your BMW. These parts are designed to be used together, and the spline lock should not run without the CBC VTT “Spline Lock” Crank hubs are CNC manufactured from 440C tool Steel with a Rockwell rating of HRC60 for the ultimate in durability, and toughness. Hub Plus OEM bolt OEM Oil pump sprocket OEM oil sprocket retainer VTT Crank bolt capture

Show More Show Less

N54 Spline Lock Crank Hub Solution With Complete Package

T#:18733525

Part#: VTT-CRANKHUB-3

Ships in 5 Business Days

$ 939.99 USD

Add to Wish List

Qty

$ 939.99 USD

Add to Wish List

Anyone with a modified N54 knows the risks involved. Upping the performance of any engine can come with some inherent risk; if we add more boost but not fuel, detonation will occur (or worse). Furthermore, improper installation, maintenance, or operation can turn a perfectly healthy engine into a paperweight. The worst failures, however, are the ones we don't plan for. When the engine simply can't handle the stresses its put under, or the design is such that it simply does not support extreme conditions. Enter the N54 crank hub. Under certain conditions, it likes to spin without warning, even when the engine is in perfect health. The engineers at Vargas saw and dealt with this problem time and again, and they saw fit to do something about it. This hub uses a proprietary "Spline Lock" technology that uses high tolerance machined splines that press into the crank and positively lock the hub to the crank. The splines are machined in such a way that rotational forces drive the hub, and splines deeper into the crank meaning when the hub encounters a situation that would normally slip a stock hub the splined hub is driven into the crank to keep it in place (much like a splined extractor). Vargas spent many months testing, and retesting this design, utilizing well over 10 different samples to come to the final production version. During testing, the final hub managed to break the testing rig before slipping. These have been bench-tested, and real-world tested on the VTT N54 race car spinning 8K RPM, and making well over 900WHP. Features: Installs the same as a stock hub Does NOT require the crank to be drilled for pins Manufactured from Harndered 17-4SS We suggest the Crank Hub System ONLY be installed by a qualified shop or technician. Timing tools are 100% REQUIRED if installed improperly engine damage may occur. DISCLAIMER: VTT and Turner Motorsport are not responsible for any engine damage caused by improper installation, or misuse of the crank hub solution.

Show More Show Less

MAHLE Forged Piston Kit 92mm, 10.1:1 CR - S65 - 4.0L

T#:2928984

Part#: 197843322

Ships on Sep 3, 2026

$ 1,429.99 USD

Add to Wish List

Qty

$ 1,429.99 USD

Add to Wish List

Forged 4032. Get the performance and reliability your S65 needs with MAHLE Motorsports PowerPak Piston Kit. Replacing the weaker factory cast aluminum pistons with the strength and durability of a forged piston.

Show More Show Less

MAHLE PowerPak Piston Set 87mm with Thermal Barrier Coating (TBC) - S...

T#:2958763

Part#: 930286125T

Special Order: No Guaranteed ETA

$ 1,271.99 USD

Add to Wish List

Qty

$ 1,271.99 USD

Add to Wish List

Forged, 2618. Get the performance and reliability your S54 needs with MAHLE Motorsports PowerPak Piston Kit. Replacing the weaker factory cast aluminum pistons with the strength and durability of a forged piston.

Show More Show Less

Project Cars

SELECT YOUR BMW

BMW Internal Engine Parts

Sub-Categories

Sneed4Speed R56 Mini Engine Rod Bearing for N14, N16, N18 1.6L Engine

MINI R55+ Sneed4Speed N Series Engine Cylinder Head Bolts Kit

MINI N14 N18 1.6L SNEED4SPEED Stock Connection Rods

Select Vehicle

Purpose

Category

Brand

Price

Special Offers

Shipping

Narrow Results