BMW Internal Engine Parts

Race German Single Vanos Rebuild - Deluxe Kit W/Modified Socket ...

T#:6843927

Part#: RGSVNSDK-MS

In Stock

$ 95.00 USD

Add to Wish List

Qty

$ 95.00 USD

Add to Wish List

Race German has devoted themselves to providing quality products for late model BMWs that cover both street and track applications. Race German has now grown their catalog to a wide variety of models and products geared towards keeping your car looking and running nice. BMW introduced VANOS in the early 90s, and it added variable valve timing to the straight six engines. Over time the VANOS unit wears out which can cause error codes or VANOS rattle. Race German has sourced quality replacement parts in an easy kit. Seal Kit: 1 PTFE Teflon Ring Seal 1 FKM (Viton) O Ring Seal 2 Copper Oil Pipe Washers Anti Rattle Bushing Set (1 Bushing + 2 Bearings) OEM Vanos Sealing Gasket *Note: a modified 18mm socket is needed to disassemble the VANOS unit. We are now offering this socket at a small charge. If you have a 1993 model single VANOS car, the 18mm socket will not work. You will need a modified 17mm socket. This kit includes the modified sockets.

Show More Show Less

VTT S55 Crank Bolt Capture - F8X S55 F3x N55

T#:557934

Part#: VTT-S55-CBC

In Stock

$ 129.99 USD

Add to Wish List

Qty

$ 129.99 USD

Add to Wish List

The S55 suffers from a weak point in its crankshaft. It has been reported that when increasing the power to the engine, the crank hub can move or spin slightly under an extreme load.

Vargas "Spline Lock" Crank Hub Solution - Includes Crank Bolt Capture...

T#:558795

Part#: VTT-CRANKHUB-1

In Stock

$ 889.99 USD

Add to Wish List

Qty

$ 889.99 USD

Add to Wish List

Under certain conditions, the N55 crank hub likes to spin, without warning and even when the engine is in perfect health. The engineers at Vargas saw and dealt with this problem time and again, and they saw fit to do something about it. This hub uses a proprietary "Spline Lock" technology that uses high tolerance machined splines which press into the crank, and positively lock the hub to the crank. The splines are machined in such a way that rotational forces drive the hub, and splines deeper into the crank meaning when the hub encounters a situation that would normally slip a stock hub the splined hub is driven into the crank to keep it in place (much like a splined extractor). Features: Installs the same as a stock hub Does NOT require the crank to be drilled for pins Manufactured from Harndered 17-4SS We suggest the Crank Hub System ONLY be installed by a qualified shop or technician. Timing tools are 100% REQUIRED if installed improperly engine damage may occur. DISCLAIMER: VTT and ECS are not responsible for any engine damage caused by improper installation, or misuse of the crank hub solution.

Show More Show Less

OEM INA Hydraulic Valve Lifter -- M62 BMW

We Price Match - Give Us A Call or Chat!

T#:19050

Part#: 11321440256

Ships in 1 Business Day

$ 82.13

This product was last offered at the strikethrough price on
07-10-2026

$ 75.26 USD

Add to Wish List

Qty

$ 75.26 USD

Add to Wish List

Any time a valve service must be performed or there is valve damage, it is recommended to replace the hydraulic lifters to keep the valve train in top condition.

OEM Schaeffler (INA, LuK, & FAG) is an engineering company that focuses on high-performance, precision manufacturing. With their individual brands INA, Luk, and FAG providing exceptionally high quality parts directly to BMW, as well as countless other automotive companies, their history of reliability and variety of offered parts makes Schaeffler a go-to replacement parts provider for all of us here at Turner Motorsport.

As a leading source of high performance BMW parts and accessories since 1993, we at Turner Motorsport are honored to be the go-to supplier for tens of thousands of enthusiasts the world over. With over two decades of parts, service, and racing experience under our belt, we provide only quality performance and replacement parts. All of our performance parts are those we would (and do!) install and run on our own cars, as well as replacement parts that are Genuine BMW or from OEM manufacturers. We only offer parts we know you can trust to perform!

Show More Show Less

Bav Auto Crankshaft Front Oil Seal Removal / Installer Tool - N54, N5...

T#:580444

Part#: B8800139

Ships on Sep 1, 2026

Sale - Save 5% $ 203.99

This product was last offered at the strikethrough price on
05-03-2026

$ 193.79 USD

Add to Wish List

Qty

Sale - Save 5%

$ 203.99

This product was last offered at the strikethrough price on
05-03-2026

$ 193.79 USD

Add to Wish List

Used in removal and installation of the front crankshaft seal on BMW N55 engines, a common job that you can save yourself a ton of money doing at home.

Glyco Connecting Rod Bearing Set

T#:375825

Part#: 11241284849

Ships in 1 Business Day

$ 92.02

This product was last offered at the strikethrough price on
07-15-2026

$ 84.36 USD

Add to Wish List

Qty

$ 84.36 USD

Add to Wish List

Standard bore - 45mm

Spline Lock Crank Hub Solution W/ Complete Package - N55 S55 ...

T#:18733532

Part#: VTT-CRANKHUB-6

Ships in 1 Business Day

$ 986.99

This product was last offered at the strikethrough price on
06-28-2026

$ 939.99 USD

Add to Wish List

Qty

$ 939.99 USD

Add to Wish List

Under certain conditions, the N55 crank hub likes to spin, without warning and even when the engine is in perfect health. The engineers at Vargas saw and dealt with this problem time and again, and they saw fit to do something about it. This hub uses a proprietary "Spline Lock" technology that uses high tolerance machined splines which press into the crank, and positively lock the hub to the crank. The splines are machined in such a way that rotational forces drive the hub, and splines deeper into the crank meaning when the hub encounters a situation that would normally slip a stock hub the splined hub is driven into the crank to keep it in place (much like a splined extractor). Features: Installs the same as a stock hub Does NOT require the crank to be drilled for pins Manufactured from Harndered 17-4SS We suggest the Crank Hub System ONLY be installed by a qualified shop or technician. Timing tools are 100% REQUIRED if installed improperly engine damage may occur. DISCLAIMER: VTT and ECS are not responsible for any engine damage caused by improper installation, or misuse of the crank hub solution.

Show More Show Less

Rod Bearing - E30 M3, E28 M5, E24 M6, E34 M5 (sold individually) ...

T#:183

Part#: 11241310515

In Stock

$ 30.59

This product was last offered at the strikethrough price on
05-03-2026

$ 27.99 USD

Limited Qty Sale

Add to Wish List

Qty

$ 30.59

This product was last offered at the strikethrough price on
05-03-2026

$ 27.99 USD

Limited Qty Sale

Add to Wish List

E30 M3, E28 M5, E24 M6, E34 M5 Rod Bearing. Sold individually. Standard sizing.

This item fits the following BMWs
1988-1991 BMW E30 M3 - 8 required.
1988 BMW E28 M5 - 12 required.
1989-1993 BMW E34 M5 3.6 liter - 12 required.
1987-1989 BMW E24 M6 - 12 required.

Show More Show Less

ECS M62TU Vanos Seal Rebuild Kit - E39, E38, E53

T#:396674

Part#: 017301ECS01

In Stock

Sale - Save 25% $ 67.99

This product was last offered at the strikethrough price on
06-13-2026

$ 50.99 USD

Add to Wish List

Qty

Sale - Save 25%

$ 67.99

This product was last offered at the strikethrough price on
06-13-2026

$ 50.99 USD

Add to Wish List

If you're not sure if your Vanos seals are bad then the only question you need to answer is if you've replaced them. Every unit from the factory came with the same failure prone o-rings and seals, even the re-manufactured units you can still get today. The only real fix is by replacing the seals and o-rings with material that is built to last in the oiled, extreme temperature environment found in these kits.

A premium product replacement with easy to follow instructions makes rebuilding your Vanos unit a must. Even thought the power loss is barely felt it's the opposite result once you replace the seals, every car that gets rebuilt ends up wowing the customer and all of them saying they didn't realize what they lost.

There are a number of symptoms that will plague your car as a result of these failing seals such as erratic idle, engine hesitation, stalling, and increased fuel consumption to name a few. If you've been chasing down any of these symptoms with no fix then this could be your issue.

Show More Show Less

WPC Treated Rod Bearing Set - M42, M44, M20, M50, M52, S50, S52, M54 ...

T#:395066

Part#: 11241284849WPC

In Stock

Sale - Save 25% $ 188.99

This product was last offered at the strikethrough price on
06-13-2026

$ 141.74 USD

Add to Wish List

Qty

Sale - Save 25%

$ 188.99

This product was last offered at the strikethrough price on
06-13-2026

$ 141.74 USD

Add to Wish List

These WPC-treated bearings are the best we have seen! WPC is a shot-peening treatment at a microscopic level. It's perfect for sensitive surfaces like bearings. The WPC treatment removes imperfections and high spots, while creating a surface that retains oil better than the original surface. This greatly reduces friction. The bearings in this kit are original equipment KS bearings that are sent to WPC for treatment. The treated bearings are stronger with less metal fatigue and less friction than buying off-the-shelf bearings from the dealer.

This item fits the following BMWs:
1984-1991 E30 BMW 318i 318is 318ic 325e 325es 325i 325ic 325is 325ix
1992-1998 E36 BMW 318i 318is 318ti 318ic 323is 323ic 325i 325is 325ic 328i 328is 328ic M3
1999-2005 E46 BMW 323i 323ci 325i 325ci 325xi 328i 328ci 330i 330ci 330xi
1982-1988 E28 BMW 528e
1989-1995 E34 BMW 525i
1997-2003 E39 BMW 525i 528i 530i
2004-2005 E60 BMW 525i 530i
2004-2006 E83 BMW X3 2.5i X3 3.0i
2000-2006 E53 BMW X5 3.0i
1997-2002 Z3 BMW Z3 1.9 Z3 2.3 Z3 2.5i Z3 2.8 Z3 3.0i M Roadster M Coupe
2003-2005 Z4 BMW Z4 2.5i Z4 3.0i

Show More Show Less

Glyco "Yellow" Crankshaft Bearing Shell - Set - E28, E30, E34, E36, E...

T#:375823

Part#: 11211706847

In Stock

$ 136.06

This product was last offered at the strikethrough price on
07-15-2026

$ 125.04 USD

Add to Wish List

Qty

$ 125.04 USD

Add to Wish List

Standard bore

Bav Auto Crankshaft Rear Oil Seal Removal / Installer Tool - N51, N52...

T#:580412

Part#: B8800104

In Stock

Sale - Save 5% $ 147.99

This product was last offered at the strikethrough price on
05-03-2026

$ 140.59 USD

Add to Wish List

Qty

Sale - Save 5%

$ 147.99

This product was last offered at the strikethrough price on
05-03-2026

$ 140.59 USD

Add to Wish List

For removal and installation of the rear crankshaft seal on BMW N51, N52 and N54 engines.

Race German Single Vanos Rebuild - Seal And Rattle Kit W/Modified Soc...

T#:6843925

Part#: RGSVNSSRK-MS

In Stock

$ 85.00 USD

Add to Wish List

Qty

$ 85.00 USD

Add to Wish List

Race German has devoted themselves to providing quality products for late model BMWs that cover both street and track applications. Race German has now grown their catalog to a wide variety of models and products geared towards keeping your car looking and running nice. BMW introduced VANOS in the early 90s, and it added variable valve timing to the straight six engines. Over time the VANOS unit wears out which can cause error codes or VANOS rattle. Race German has sourced quality replacement parts in an easy kit. Seal Kit: 1 PTFE Teflon Ring Seal 1 FKM (Viton) O Ring Seal 2 Copper Oil Pipe Washers Anti Rattle Bushing Set (1 Bushing + 2 Bearings) *Note: a modified 18mm socket is needed to disassemble the VANOS unit. We are now offering this socket at a small charge. If you have a 1993 model single VANOS car, the 18mm socket will not work. You will need a modified 17mm socket. This kit includes the modified sockets.

Show More Show Less

Bav Auto Intermediate Lever Valve Spring Compressor - N20/26 N55 ...

T#:580431

Part#: B8800124

Ships on Sep 1, 2026

Sale - Save 15% $ 178.99

This product was last offered at the strikethrough price on
05-03-2026

$ 152.14 USD

Add to Wish List

Qty

Sale - Save 15%

$ 178.99

This product was last offered at the strikethrough price on
05-03-2026

$ 152.14 USD

Add to Wish List

For installation and removal of pressure springs on intermediate levers of valve train. Ensures quick, easy and safe handling of these high force springs.

OEM INA Timing Chain Tensioner - E30 E36 Z3 with M42 / M44 engine ...

We Price Match - Give Us A Call or Chat!

T#:4469

Part#: 11311743187

In Stock

$ 67.65

This product was last offered at the strikethrough price on
05-06-2026

$ 51.99 USD

Add to Wish List

Qty

$ 51.99 USD

Add to Wish List

This timing chain tensioner keeps the tension rail properly positioned on the BMW M42 and M44 4 cylinder engine.

OEM Schaeffler (INA, LuK, & FAG) is an engineering company that focuses on high-performance, precision manufacturing. With their individual brands INA, Luk, and FAG providing exceptionally high quality parts directly to BMW, as well as countless other automotive companies, their history of reliability and variety of offered parts makes Schaeffler a go-to replacement parts provider for all of us here at Turner Motorsport.

As a leading source of high performance BMW parts and accessories since 1993, we at Turner Motorsport are honored to be the go-to supplier for tens of thousands of enthusiasts the world over. With over two decades of parts, service, and racing experience under our belt, we provide only quality performance and replacement parts. All of our performance parts are those we would (and do!) install and run on our own cars, as well as replacement parts that are Genuine BMW or from OEM manufacturers. We only offer parts we know you can trust to perform!

This item fits the following BMWs:
1990-1991 E30 BMW 318i 318is 318ic
1992-1998 E36 BMW 318i 318is 318ti 318ic
1997-1999 Z3 BMW Z3 1.9

Show More Show Less

Spline N55 S55 Lock Crank Hub Solution W/ Hardware Package

T#:18733531

Part#: VTT-CRANKHUB-5

Ships in 10 Business Days

$ 880.99 USD

Add to Wish List

Qty

$ 880.99 USD

Add to Wish List

Under certain conditions, the N55 crank hub likes to spin, without warning and even when the engine is in perfect health. The engineers at Vargas saw and dealt with this problem time and again, and they saw fit to do something about it. This hub uses a proprietary "Spline Lock" technology that uses high tolerance machined splines which press into the crank, and positively lock the hub to the crank. The splines are machined in such a way that rotational forces drive the hub, and splines deeper into the crank meaning when the hub encounters a situation that would normally slip a stock hub the splined hub is driven into the crank to keep it in place (much like a splined extractor). Features: Installs the same as a stock hub Does NOT require the crank to be drilled for pins Manufactured from Harndered 17-4SS We suggest the Crank Hub System ONLY be installed by a qualified shop or technician. Timing tools are 100% REQUIRED if installed improperly engine damage may occur. DISCLAIMER: VTT and ECS are not responsible for any engine damage caused by improper installation, or misuse of the crank hub solution.

Show More Show Less

Bavarian Autosport Crankshaft Holding Tool - BMW

T#:580450

Part#: B8800145

In Stock

Sale - Save 15% $ 77.99

This product was last offered at the strikethrough price on
05-03-2026

$ 66.29 USD

Add to Wish List

Qty

Sale - Save 15%

$ 77.99

This product was last offered at the strikethrough price on
05-03-2026

$ 66.29 USD

Add to Wish List

Makes removal of crankshaft hub nut/bolt much easier. A must-have for replacing timing chains, oil pump chains, leaking crankshaft seals and more.

Bav Auto Crankshaft Pulley Holding Tool

T#:580404

Part#: B8800094

In Stock

Sale - Save 10% $ 180.99

This product was last offered at the strikethrough price on
05-03-2026

$ 162.89 USD

Add to Wish List

Qty

Sale - Save 10%

$ 180.99

This product was last offered at the strikethrough price on
05-03-2026

$ 162.89 USD

Add to Wish List

Bav Auto's Crankshaft Pulley Holding Tool enables you to remove your crankshaft nut/bolt with ease - we recommend this tool if you intend on replacing timing chains, oil pump chains, leaking crankshaft seals, etc.

Show More Show Less

OEM INA Timing Chain Sprocket - Exhaust Camshaft - BMW N20 2.0L ...

We Price Match - Give Us A Call or Chat!

T#:20254639

Part#: 11367583819

In Stock

$ 101.99 USD

Add to Wish List

Qty

$ 101.99 USD

Add to Wish List

Improve the performance and reliability of your BMW N20 2.0L engine with the BMW N20 2.0L Timing Chain Sprocket for the exhaust camshaft. This high-quality replacement part ensures precise timing and smooth operation of the exhaust camshaft, enhancing overall engine efficiency and longevity.

Enhances engine performance and reliability
Ensures precise timing of the exhaust camshaft
High-quality construction for long-lasting durability
Compatible with BMW N20 2.0L engines

If your timing chain sprockets are worn or damaged, replace them with this replacement part to ensure that your car has proper timing at all times.

Show More Show Less

WPC Treated Crank Bearing Set

T#:585720

Part#: 11211706847WPCKT

In Stock

Sale - Save 3% $ 250.99

This product was last offered at the strikethrough price on
06-14-2026

$ 243.46 USD

Add to Wish List

Qty

Sale - Save 3%

$ 250.99

This product was last offered at the strikethrough price on
06-14-2026

$ 243.46 USD

Add to Wish List

What's better than using new crank bearings in your next engine build? WPC-treated bearings! What is WPC, you ask? WPC is a surface treatment that reduces friction and adds strength - two improvements that benefit internal engine components. Ultra-fine particles are fired at the surface at very high speeds, like shot-peening - but much, much smaller. The parts come out smoother and stronger due to thermal discharge. The two largest enemies of any high-performance engine are heat and friction - and WPC has found a way to reduce both. What are you waiting for? Use WPC-treated bearings on your next engine build or crank service!

Show More Show Less

Main Bearing Set - Standard Size - E30 M3 2.3 liter

T#:3166

Part#: 11210666110

Ships in 3 Business Days

$ 99.99 USD

Add to Wish List

Qty

$ 99.99 USD

Add to Wish List

This E30 M3 Main bearing set is in standard size for the 2.3 liter S14 engine. This main bearing kit includes the thrust bearings.

This item fits the following BMWs:
1988-1991 E30 BMW M3

Show More Show Less

Race German Single Vanos Rebuild - Deluxe Kit

T#:6843926

Part#: RGSVNSDK

Ships in 4 Business Days

$ 101.99 USD

Add to Wish List

Qty

$ 101.99 USD

Add to Wish List

Race German has devoted themselves to providing quality products for late model BMWs that cover both street and track applications. Race German has now grown their catalog to a wide variety of models and products geared towards keeping your car looking and running nice. BMW introduced VANOS in the early 90s, and it added variable valve timing to the straight six engines. Over time the VANOS unit wears out which can cause error codes or VANOS rattle. Race German has sourced quality replacement parts in an easy kit. Seal Kit: 1 PTFE Teflon Ring Seal 1 FKM (Viton) O Ring Seal 2 Copper Oil Pipe Washers Anti Rattle Bushing Set (1 Bushing + 2 Bearings) OEM Vanos Sealing Gasket *Note: a modified 18mm socket is needed to disassemble the VANOS unit. We are now offering this socket at a small charge. If you have a 1993 model single VANOS car, the 18mm socket will not work. You will need a modified 17mm socket. This kit does not include the modified sockets.

Show More Show Less

OEM INA Engine Timing Chain - M50, M52, M54, S50, S52

T#:42301980

Part#: ZC0255

Ships in 7 Business Days

$ 41.99 USD

Add to Wish List

Qty

$ 41.99 USD

Add to Wish List

Preserve the performance and longevity of your BMW with the OEM INA Engine Timing Chain. Timing chains stretch over time causing sluggish performance, a check engine light or even a misfire. Replace yours today!

Show More Show Less

Glyco Main Bearing Set (Standard) - E21, E28, E30

Features All Single-Tang Main Bearings for Earlier M20 Engines

T#:1196183

Part#: 11211722342

In Stock

$ 259.99

This product was last offered at the strikethrough price on
05-03-2026

$ 231.99 USD

Add to Wish List

Qty

$ 231.99 USD

Add to Wish List

E60 M5/E63 M6 WPC Treated S85 Rod Bearings (Set)

T#:388759

Part#: 11247841702WPCKT

In Stock

$ 1,086.99 USD

Add to Wish List

Qty

$ 1,086.99 USD

Add to Wish List

These WPC-treated bearings are the best we have seen for the S85. WPC is a shot-peening treatment at a microscopic level. It's perfect for sensitive surfaces like bearings. The WPC treatment removes imperfections and high spots, while creating a surface that retains oil better than the original surface. This greatly reduces friction. The bearings in this kit are factory BMW bearings that are sent to WPC for treatment. The treated bearings are stronger with less metal fatigue and less friction than buying off-the-shelf bearings from the dealer.

Price is for a complete set of S85 upgraded rod bearings.

Show More Show Less

WPC Treated Main Bearing Set - Standard Size - E30 M3 2.3 Liter ...

T#:13299324

Part#: 11210666110WP2KT

Ships on Sep 11, 2026

$ 174.99 USD

Add to Wish List

Qty

$ 174.99 USD

Add to Wish List

Vargas "Spline Lock" Crank Hub Solution - N54

T#:558924

Part#: VTT-N54-CRANKHUB

Ships in 10 Business Days

$ 818.99 USD

Add to Wish List

Qty

$ 818.99 USD

Add to Wish List

Anyone with a modified N54 knows the risks involved. Upping the performance of any engine can come with some inherent risk; if we add more boost but not fuel, detonation will occur (or worse). Furthermore, improper installation, maintenance, or operation can turn a perfectly healthy engine into a paperweight. The worst failures, however, are the ones we don't plan for. When the engine simply can't handle the stresses its put under, or the design is such that it simply does not support extreme conditions. Enter the N54 crank hub. Under certain conditions, it likes to spin without warning, even when the engine is in perfect health. The engineers at Vargas saw and dealt with this problem time and again, and they saw fit to do something about it. This hub uses a proprietary "Spline Lock" technology that uses high tolerance machined splines that press into the crank and positively lock the hub to the crank. The splines are machined in such a way that rotational forces drive the hub, and splines deeper into the crank meaning when the hub encounters a situation that would normally slip a stock hub the splined hub is driven into the crank to keep it in place (much like a splined extractor). Vargas spent many months testing, and retesting this design, utilizing well over 10 different samples to come to the final production version. During testing, the final hub managed to break the testing rig before slipping. These have been bench-tested, and real-world tested on the VTT N54 race car spinning 8K RPM, and making well over 900WHP. Features: Installs the same as a stock hub Does NOT require the crank to be drilled for pins Manufactured from Harndered 17-4SS We suggest the Crank Hub System ONLY be installed by a qualified shop or technician. Timing tools are 100% REQUIRED if installed improperly engine damage may occur. DISCLAIMER: VTT and Turner Motorsport are not responsible for any engine damage caused by improper installation, or misuse of the crank hub solution. The worst failures, however, are the ones we don't plan for. When the engine simply can't handle the stresses its put under, or the design is such that it simply does not support extreme conditions. Enter the N54 crank hub. Under certain conditions, it likes to spin without warning, even when the engine is in perfect health. The engineers at Vargas saw and dealt with this problem time and again, and they saw fit to do something about it. This hub uses a proprietary "Spline Lock" technology that uses high tolerance machined splines that press into the crank and positively lock the hub to the crank. The splines are machined in such a way that rotational forces drive the hub, and splines deeper into the crank meaning when the hub encounters a situation that would normally slip a stock hub the splined hub is driven into the crank to keep it in place (much like a splined extractor). Vargas spent many months testing, and retesting this design, utilizing well over 10 different samples to come to the final production version. During testing, the final hub managed to break the testing rig before slipping. These have been bench-tested, and real-world tested on the VTT N54 race car spinning 8K RPM, and making well over 900WHP. Features: Installs the same as a stock hub Does NOT require the crank to be drilled for pins Manufactured from Harndered 17-4SS We suggest the Crank Hub System ONLY be installed by a qualified shop or technician. Timing tools are 100% REQUIRED if installed improperly engine damage may occur. DISCLAIMER: VTT and Turner Motorsport are not responsible for any engine damage caused by improper installation, or misuse of the crank hub solution. The product comes with a 1-year unlimited mileage warranty from manufacturer defects.

Show More Show Less

Glyco "Yellow" Crankshaft Bearing Shell - Set - E30, E36, E39, E46, E...

T#:375824

Part#: 11211706850

In Stock at Vendor

$ 126.61

This product was last offered at the strikethrough price on
07-15-2026

$ 118.92 USD

Add to Wish List

Qty

$ 118.92 USD

Add to Wish List

59.75MM(+0.25) bore

Race German Single Vanos Rebuild - Seal And Rattle Kit

T#:6843924

Part#: RGSVNSSRK

Ships in 4 Business Days

$ 89.99 USD

Add to Wish List

Qty

$ 89.99 USD

Add to Wish List

Race German has devoted themselves to providing quality products for late model BMWs that cover both street and track applications. Race German has now grown their catalog to a wide variety of models and products geared towards keeping your car looking and running nice. BMW introduced VANOS in the early 90s, and it added variable valve timing to the straight six engines. Over time the VANOS unit wears out which can cause error codes or VANOS rattle. Race German has sourced quality replacement parts in an easy kit. Seal Kit: 1 PTFE Teflon Ring Seal 1 FKM (Viton) O Ring Seal 2 Copper Oil Pipe Washers Anti Rattle Bushing Set (1 Bushing + 2 Bearings) *Note: a modified 18mm socket is needed to disassemble the VANOS unit. We are now offering this socket at a small charge. If you have a 1993 model single VANOS car, the 18mm socket will not work. You will need a modified 17mm socket. This kit does not include the modified sockets.

Show More Show Less

Race German Single Vanos Rebuild - Seal Kit W/Modified Socket ...

T#:6843923

Part#: RGSVNSSK-MS

Ships in 2 Business Days

$ 55.00 USD

Add to Wish List

Qty

$ 55.00 USD

Add to Wish List

Race German has devoted themselves to providing quality products for late model BMWs that cover both street and track applications. Race German has now grown their catalog to a wide variety of models and products geared towards keeping your car looking and running nice. BMW introduced VANOS in the early 90s, and it added variable valve timing to the straight six engines. Over time the VANOS unit wears out which can cause error codes or VANOS rattle. Race German has sourced quality replacement parts in an easy kit. Seal Kit: 1 PTFE Teflon Ring Seal 1 FKM (Viton) O Ring Seal 2 Copper Oil Pipe Washers *Note: a modified 18mm socket is needed to disassemble the VANOS unit. We are now offering this socket at a small charge. If you have a 1993 model single VANOS car, the 18mm socket will not work. You will need a modified 17mm socket. This kit includes the modified sockets.

Show More Show Less

Spline Lock Crank Hub Solution

T#:8061334

Part#: VTT-N55-CRANKHUB

Ships in 10 Business Days

$ 818.99 USD

Add to Wish List

Qty

$ 818.99 USD

Add to Wish List

Under certain conditions, the N55 crank hub likes to spin, without warning and even when the engine is in perfect health. The engineers at Vargas saw and dealt with this problem time and again, and they saw fit to do something about it. This hub uses a proprietary "Spline Lock" technology that uses high tolerance machined splines which press into the crank, and positively lock the hub to the crank. The splines are machined in such a way that rotational forces drive the hub, and splines deeper into the crank meaning when the hub encounters a situation that would normally slip a stock hub the splined hub is driven into the crank to keep it in place (much like a splined extractor). Features: Installs the same as a stock hub Does NOT require the crank to be drilled for pins Manufactured from Harndered 17-4SS We suggest the Crank Hub System ONLY be installed by a qualified shop or technician. Timing tools are 100% REQUIRED if installed improperly engine damage may occur. DISCLAIMER: VTT and ECS are not responsible for any engine damage caused by improper installation, or misuse of the crank hub solution. This hub uses a proprietary "Spline Lock" technology that uses high tolerance machined splines which press into the crank, and positively lock the hub to the crank. The splines are machined in such a way that rotational forces drive the hub, and splines deeper into the crank meaning when the hub encounters a situation that would normally slip a stock hub the splined hub is driven into the crank to keep it in place (much like a splined extractor). Features: Installs the same as a stock hub Does NOT require the crank to be drilled for pins Manufactured from Harndered 17-4SS We suggest the Crank Hub System ONLY be installed by a qualified shop or technician. Timing tools are 100% REQUIRED if installed improperly engine damage may occur. DISCLAIMER: VTT and ECS are not responsible for any engine damage caused by improper installation, or misuse of the crank hub solution. The product comes with a 1-year unlimited mileage warranty from manufacturer defects.

Show More Show Less

Race German Single Vanos Rebuild - Seal Kit

T#:6843922

Part#: RGSVNSSK

Ships in 1 Business Day

$ 53.99 USD

Add to Wish List

Qty

$ 53.99 USD

Add to Wish List

Race German has devoted themselves to providing quality products for late model BMWs that cover both street and track applications. Race German has now grown their catalog to a wide variety of models and products geared towards keeping your car looking and running nice. BMW introduced VANOS in the early 90s, and it added variable valve timing to the straight six engines. Over time the VANOS unit wears out which can cause error codes or VANOS rattle. Race German has sourced quality replacement parts in an easy kit. Seal Kit: 1 PTFE Teflon Ring Seal 1 FKM (Viton) O Ring Seal 2 Copper Oil Pipe Washers *Note: a modified 18mm socket is needed to disassemble the VANOS unit. We are now offering this socket at a small charge. If you have a 1993 model single VANOS car, the 18mm socket will not work. You will need a modified 17mm socket. This kit does not include the modified sockets.

Show More Show Less

Spline Lock Crank Hub Solution W/ Crank Bolt Capture - N54

T#:18733527

Part#: VTT-CRANKHUB-2

Ships in 10 Business Days

$ 871.99 USD

Add to Wish List

Qty

$ 871.99 USD

Add to Wish List

Anyone with a modified N54 knows the risks involved. Upping the performance of any engine can come with some inherent risk; if we add more boost but not fuel, detonation will occur (or worse). Furthermore, improper installation, maintenance, or operation can turn a perfectly healthy engine into a paperweight. The worst failures, however, are the ones we don't plan for. When the engine simply can't handle the stresses its put under, or the design is such that it simply does not support extreme conditions. Enter the N54 crank hub. Under certain conditions, it likes to spin without warning, even when the engine is in perfect health. The engineers at Vargas saw and dealt with this problem time and again, and they saw fit to do something about it. This hub uses a proprietary "Spline Lock" technology that uses high tolerance machined splines that press into the crank and positively lock the hub to the crank. The splines are machined in such a way that rotational forces drive the hub, and splines deeper into the crank meaning when the hub encounters a situation that would normally slip a stock hub the splined hub is driven into the crank to keep it in place (much like a splined extractor). Vargas spent many months testing, and retesting this design, utilizing well over 10 different samples to come to the final production version. During testing, the final hub managed to break the testing rig before slipping. These have been bench-tested, and real-world tested on the VTT N54 race car spinning 8K RPM, and making well over 900WHP. Features: Installs the same as a stock hub Does NOT require the crank to be drilled for pins Manufactured from Harndered 17-4SS We suggest the Crank Hub System ONLY be installed by a qualified shop or technician. Timing tools are 100% REQUIRED if installed improperly engine damage may occur. DISCLAIMER: VTT and Turner Motorsport are not responsible for any engine damage caused by improper installation, or misuse of the crank hub solution.

Show More Show Less

Spline Lock Crank Hub Solution W/ Hardware Package - N54

T#:18733526

Part#: VTT-CRANKHUB-4

Ships in 10 Business Days

$ 880.99 USD

Add to Wish List

Qty

$ 880.99 USD

Add to Wish List

Anyone with a modified N54 knows the risks involved. Upping the performance of any engine can come with some inherent risk; if we add more boost but not fuel, detonation will occur (or worse). Furthermore, improper installation, maintenance, or operation can turn a perfectly healthy engine into a paperweight. The worst failures, however, are the ones we don't plan for. When the engine simply can't handle the stresses its put under, or the design is such that it simply does not support extreme conditions. Enter the N54 crank hub. Under certain conditions, it likes to spin without warning, even when the engine is in perfect health. The engineers at Vargas saw and dealt with this problem time and again, and they saw fit to do something about it. This hub uses a proprietary "Spline Lock" technology that uses high tolerance machined splines that press into the crank and positively lock the hub to the crank. The splines are machined in such a way that rotational forces drive the hub, and splines deeper into the crank meaning when the hub encounters a situation that would normally slip a stock hub the splined hub is driven into the crank to keep it in place (much like a splined extractor). Vargas spent many months testing, and retesting this design, utilizing well over 10 different samples to come to the final production version. During testing, the final hub managed to break the testing rig before slipping. These have been bench-tested, and real-world tested on the VTT N54 race car spinning 8K RPM, and making well over 900WHP. Features: Installs the same as a stock hub Does NOT require the crank to be drilled for pins Manufactured from Harndered 17-4SS We suggest the Crank Hub System ONLY be installed by a qualified shop or technician. Timing tools are 100% REQUIRED if installed improperly engine damage may occur. DISCLAIMER: VTT and Turner Motorsport are not responsible for any engine damage caused by improper installation, or misuse of the crank hub solution.

Show More Show Less

Rod Bearing Set (+0.25)

T#:23748157

Part#: 112412848516CYL-

Ships in 1 Business Day

$ 331.13

This product was last offered at the strikethrough price on
07-15-2026

$ 305.57 USD

Add to Wish List

Qty

$ 305.57 USD

Add to Wish List

VTT N54 “Spline Lock” CrankHub Solution Package W/ Crank Bolt Cap...

T#:19395579

Part#: VTTCRANKHUBPKG

Ships in 10 Business Days

$ 934.99 USD

Add to Wish List

Qty

$ 934.99 USD

Add to Wish List

VTT is proud to offer the only complete N54 complete crank hub solution that does NOT require the crank to be drilled for pins. Our hub uses our proprietary “Spline Lock” technology that uses high tolerance machined splines which press into the crank, and positively lock the hub to the crank. The splines are machined in such a way that rotational forces drive the hub, and splines deeper into the crank meaning when the hub encounters a situation that would normally slip a stock hub the splined hub is driven into the crank to keep it in place (much like a splined extractor). We spent many months testing, and retesting this design, utilizing well over 10 different samples to come to our final production version. During testing, our final hub managed to break our testing rig before slipping. These have been bench tested, and real-world tested on the VTT N54 race car spinning 8K RPM and making well over 900WHP. This technology means our hub installs the same as a stock hub, no drilling of the crank, which means MUCH less labor is involved and is reversible is ever wanting to be uninstalled leaving no holes in the crank. The “Spline Lock” is ONLY available with the VTT Crank bolt capture for the ULTIMATE Crank Hub solution for your BMW. These parts are designed to be used together, and the spline lock should not run without the CBC VTT “Spline Lock” Crank hubs are CNC manufactured from 440C tool Steel with a Rockwell rating of HRC60 for the ultimate in durability, and toughness. Hub Plus OEM bolt OEM Oil pump sprocket OEM oil sprocket retainer VTT Crank bolt capture

Show More Show Less

Glyco "Green" Crankshaft Bearing Shell - Set - E39, E46, E53, E83, Z3...

T#:374671

Part#: 11211706848

Ships in 1-2 days

$ 194.32 USD

Add to Wish List

Qty

$ 194.32 USD

Add to Wish List

Standard bore

WPC Treated Genuine BMW Rod Bearings - Full Set

T#:389729

Part#: 11241407493WPCKT

Ships in 1-2 days

$ 1,231.84 USD

Add to Wish List

Qty

$ 1,231.84 USD

Add to Wish List

These WPC-treated bearings are the best we have seen for the S62. WPC is a shot-peening treatment at a microscopic level. It's perfect for sensitive surfaces like bearings. The WPC treatment removes imperfections and high spots, while creating a surface that retains oil better than the original surface. This greatly reduces friction. The bearings in this kit are factory BMW bearings that are sent to WPC for treatment. The treated bearings are stronger with less metal fatigue and less friction than buying off-the-shelf bearings from the dealer.

Price is for a complete set of S62 upgraded rod bearings.

Show More Show Less

N54 Spline Lock Crank Hub Solution With Complete Package

T#:18733525

Part#: VTT-CRANKHUB-3

Ships in 5 Business Days

$ 939.99 USD

Add to Wish List

Qty

$ 939.99 USD

Add to Wish List

Anyone with a modified N54 knows the risks involved. Upping the performance of any engine can come with some inherent risk; if we add more boost but not fuel, detonation will occur (or worse). Furthermore, improper installation, maintenance, or operation can turn a perfectly healthy engine into a paperweight. The worst failures, however, are the ones we don't plan for. When the engine simply can't handle the stresses its put under, or the design is such that it simply does not support extreme conditions. Enter the N54 crank hub. Under certain conditions, it likes to spin without warning, even when the engine is in perfect health. The engineers at Vargas saw and dealt with this problem time and again, and they saw fit to do something about it. This hub uses a proprietary "Spline Lock" technology that uses high tolerance machined splines that press into the crank and positively lock the hub to the crank. The splines are machined in such a way that rotational forces drive the hub, and splines deeper into the crank meaning when the hub encounters a situation that would normally slip a stock hub the splined hub is driven into the crank to keep it in place (much like a splined extractor). Vargas spent many months testing, and retesting this design, utilizing well over 10 different samples to come to the final production version. During testing, the final hub managed to break the testing rig before slipping. These have been bench-tested, and real-world tested on the VTT N54 race car spinning 8K RPM, and making well over 900WHP. Features: Installs the same as a stock hub Does NOT require the crank to be drilled for pins Manufactured from Harndered 17-4SS We suggest the Crank Hub System ONLY be installed by a qualified shop or technician. Timing tools are 100% REQUIRED if installed improperly engine damage may occur. DISCLAIMER: VTT and Turner Motorsport are not responsible for any engine damage caused by improper installation, or misuse of the crank hub solution.

Show More Show Less

OEM INA Timing Chain Sprocket - Inlet Camshaft - BMW N20 2.0L ...

We Price Match - Give Us A Call or Chat!

T#:35998448

Part#: 11367583818KIT

Back Ordered

$ 267.99 USD

Add to Wish List

Qty

$ 267.99 USD

Add to Wish List

Replace this so your timing chain meshes perfectly with the gear teeth for optimal performance.

WPC Treated Cam Bearing Ledge - Exhaust - BMW N52 2.0L N54 N55 3.0L ...

T#:585946

Part#: 11127531224WPC

In Stock

$ 916.99 USD

Add to Wish List

Qty

$ 916.99 USD

Add to Wish List

A common issue on N54 motors is cam bearing ledge scoring due to lack of lubrication, and if left unattended can cause damage to the camshaft and increase oil consumption. These WPC-treated cam bearing ledges help prevent lubrication issues to ensure no scoring occurs on the bearing ledge or camshaft. What is WPC, you ask? WPC is a surface treatment that reduces friction and adds strength - two improvements that benefit internal engine components. Ultra-fine particles are fired at the surface at very high speeds, like shot-peening - but much, much smaller. The parts come out smoother and stronger due to thermal discharge. The two largest enemies of any high-performance engine are heat and friction - and WPC has found a way to reduce both.

Show More Show Less

OEM Ina Intake Hydraulic Tappet - BMW N52 N54 N55 N20 S55

We Price Match - Give Us A Call or Chat!

T#:591661

Part#: 11337548690

In Stock

$ 15.99 USD

Add to Wish List

Qty

$ 15.99 USD

Add to Wish List

Hydraulic valve lifter

WPC Treated Cam Bearing Ledge - Intake - BMW N54 3.0L

T#:585945

Part#: 11127550913WPC

In Stock

$ 898.99 USD

Add to Wish List

Qty

$ 898.99 USD

Add to Wish List

A common issue on N54 motors is cam bearing ledge scoring due to lack of lubrication, and if left unattended can cause damage to the camshaft and increase oil consumption. These WPC-treated cam bearing ledges help prevent lubrication issues to ensure no scoring occurs on the bearing ledge or camshaft. What is WPC, you ask? WPC is a surface treatment that reduces friction and adds strength - two improvements that benefit internal engine components. Ultra-fine particles are fired at the surface at very high speeds, like shot-peening - but much, much smaller. The parts come out smoother and stronger due to thermal discharge. The two largest enemies of any high-performance engine are heat and friction - and WPC has found a way to reduce both.

Show More Show Less

WPC Treated Cam Bearing Ledge Kit - BMW N54 3.0L

T#:14651263

Part#: 11127550913WKT

In Stock

$ 1,815.99 USD

Add to Wish List

Qty

$ 1,815.99 USD

Add to Wish List

A common issue on N54 motors is cam bearing ledges scoring due to lack of lubrication, and if left unattended can cause damage to the camshafts and increase oil consumption. These WPC-treated cam bearing ledges help prevent lubrication issues to ensure no scoring occurs on the bearing ledge or camshaft. What is WPC, you ask? WPC is a surface treatment that reduces friction and adds strength - two improvements that benefit internal engine components. Ultra-fine particles are fired at the surface at very high speeds, like shot-peening - but much, much smaller. The parts come out smoother and stronger due to thermal discharge. The two largest enemies of any high-performance engine are heat and friction - and WPC has found a way to reduce both.

Show More Show Less

OEM INA Hydraulic Lifter - BMW M5X S5X M62 S62

We Price Match - Give Us A Call or Chat!

T#:360996

Part#: 11321748884

In Stock

$ 19.99 USD

Add to Wish List

Qty

$ 19.99 USD

Add to Wish List

Stock replacement hydraulic valve lifter for the M52, M54 and S50 S52 engines. These lifter buckets can last 150,000+ miles but then they no longer fit on the valve stem correctly and a ticking or knocking noise can result. If the lifter is no longer seated correctly, it can lead to the valve not opening correctly. Replacement is straight-forward but requires special tools for working with the camshafts. This item fits the following BMWs:
1995-1998 E36 BMW 323is 323ic 328i 328is 328ic M3
1997-2003 E39 BMW 525i 528i 530i M5
1999-2005 E46 BMW 323i 323ci 325i 325ci 325xi 328i 328ci 330i 330ci 330xi
2004-2005 E60 BMW 525i 530i
2004-2005 E83 BMW X3 2.5i X3 3.0i
2000-2006 E53 BMW X5 3.0i
1996-2002 E36/7 BMW Z3 2.3 Z3 2.5i Z3 2.8 Z3 3.0i
1998-2000 E36/7 BMW M Roadster M Coupe

Show More Show Less