BMW Suspension Parts

The B16 PSS10 coilovers offer a stiffer spring rate than stock and a lower ride height for less bodyroll and better handling. These are among the easiest coil over kits on the market - no special mounts required (works with stock mounts and sway bar links), larger adjustment knob allows for easy shock damping changes, and coil over spanner wrenches included for easy height changes. Bilstein backs up their technology with a limited lifetime warranty. TUV approved for fitment, safety, and quality!

Bilstein's monotube shock dampers in the PSS10 offer 10 precise settings for compression and rebound. A new setting is just a click away, allowing you to set a ride and handling combination that works for your setting. Instead of offering too many shock settings that you're never going to use, Bilstein has chosen ten optimal damping curves from a smooth street setting (P10) to an ultra-stiff track-only setup (P1). Shock changes are made from an easy-to-use over-sized adjuster knob.

Ride height adjustments are done from perches that ride on each shock body, which are zinc coated for excellent wear and corrosion resistance. You can set the ride height between 0.5 to 1.3 inches lower than stock ride height. Springs are progressively rated so their initial compression rating is quite soft and then becomes stiffer as the spring compresses. These are stiffer than most coil over kit manufacturers and the results of Bilstein's extensive testing on the German Nurgburgring and Autobahn.

The fitment of these is just like a standard shock and spring package. The front struts and rear shocks are compatible with the stock strut and shock mounts. You can re-use your own or choose a mount with additional features. Because the Bilstein design keeps the sway bar tab in the original location, you can re-use the stock sway bar links. Using the stock mounts keeps the cost and complexity down and allows for TUV certification. You can also be assured of the stock mount's quiet and long-lasting performance. The assembly of the front strut is the same as a the factory strut. In the rear, ride height is made by an adjustable spring perch that sits under the rear spring. Install instructions and diagrams included.

If you're looking for a supremely capable and high quality suspension, then look no further than the Bilstein PSS10. It combines all of the best German engineering with real-world development, and a lifetime warranty.

Fitment note: this system works only on cars not equipped with the factory EDC electronically adjustable shocks.

Featuring:

• Largest available piston diameter for greater sensitivity and precise control.
• Patented digressive piston head design and deflective valving instantly reacts to changing road conditions.
• 10-way adjustable dampening knobs that "click" from soft to hard with no tools or jacking required.
• Monotube design dissipates heat more effectively than a twin tube shock for cooler, more efficient operation and longer life.
• Weather resistant coating to resist oxidization, and ensure long life.
• Lighter weight reduces wear and tear on suspension components.
• Wrenches to adjust front and rear ride height included!

This coilover kit fits the following BMWs:
2008+ E82 BMW 128i 135i
2006+ E90 BMW 325i 328i 330i 335d 335i
2007+ E92 BMW 328i 335i 335is
2007+ E93 BMW 328i 335i

Remove and install the three bushings and ball joints that are pressed into the rear trailing arm. Use this one tool kit for on-vehicle or off-vehicle removal and replacement of the Rear Trailing Arm Bushing, Outer Upper Control Arm Bushing (ball joint) and Outer Lower Control Arm Bushing (ball joint). This tool is designed to work on E36 3-series (except E36 318ti), E46 3-series, E83 X3 and E85/E86 Z4 Coupe & Roadster.

From 1974 to 2019, Bavarian Autosport was one of the premier vendors for BMW and MINI auto parts. We are happy to preserve the Bav Auto legacy by continuing to carry their high-quality products into the future. All Bav Auto parts will remain unchanged in design and sourced from the same OEM suppliers to ensure long-lasting reliability. We trust these parts, accessories, and upgrades so confidently that we back every Bavarian Autosport branded component with a 2-year warranty.

Dinan Performance Springs are matched to your BMW's chassis and suspension components to deliver better handling and looks without sacrificing ride quality. Dinan BMW springs are carefully engineered to work within your car's suspension travel and to improve suspension geometry. Spring rates are slightly stiffer than stock and dialed in to reduce bodyroll. A stiffer suspension makes the car more fun to drive and the lower ride height improves the looks by reducing wheel-fender gap.

Dinan spring specs -

• F: -1/2" (12mm)
  
• R: -1/2" (12mm)

Fitment note: When used with stock shocks the Dinan Ride Quality Kit is strongly recommended. The Kit consists of shorter and stiffer bump stops and spring perches that work better with the lowered ride height of these springs. While not explicitly required, less than favorable ride quality and handling may result without them.

For over 35 years, Dinan has been America's premier tuning company, pioneering advancements in BMW modification while retaining a focus on balanced performance that preserves the original character and driving feel that a BMW offers. When you install a Dinan part on your car, know that it's not only carefully developed and tested, but that Dinan stands behind it with a four year, 50,000-mile warranty. Dinan believes so fully in their “total package” approach that once your car has been fitted with enough of their parts, they celebrate your conversion from stock to Dinan with an exclusive trunk badge, displayed proudly by BMW enthusiasts everywhere. The springs are worth 2 points towards your Dinan badge (Ride Quality Kit is worth 1 point).

This item fits the following BMWs:
2011+ F10 BMW 550i 550xi

Dinan Performance Springs are matched to your BMW's chassis and suspension components to deliver better handling and looks without sacrificing ride quality. Dinan BMW springs are carefully engineered to work within your car's suspension travel and to improve suspension geometry. Spring rates are slightly stiffer than stock and dialed in to reduce bodyroll. A stiffer suspension makes the car more fun to drive and the lower ride height improves the looks by reducing wheel-fender gap.

Dinan spring specs -

• F: -3/4" (19mm)
  
• R: -3/4" (19mm)

Fitment note: When used with stock shocks the Dinan Ride Quality Kit is strongly recommended. The Kit consists of shorter and stiffer bump stops and spring perches that work better with the lowered ride height of these springs. While not explicitly required, less than favorable ride quality and handling may result without them.

For over 35 years, Dinan has been America's premier tuning company, pioneering advancements in BMW modification while retaining a focus on balanced performance that preserves the original character and driving feel that a BMW offers. When you install a Dinan part on your car, know that it's not only carefully developed and tested, but that Dinan stands behind it with a four year, 50,000-mile warranty. Dinan believes so fully in their “total package” approach that once your car has been fitted with enough of their parts, they celebrate your conversion from stock to Dinan with an exclusive trunk badge, displayed proudly by BMW enthusiasts everywhere. The springs are worth 2 points towards your Dinan badge (Ride Quality Kit is worth 1 point).

This item fits the following BMWs:
2012+ F30 BMW 320i 328i 330i - Sedan

Dinan Performance Springs are matched to your BMW's chassis and suspension components to deliver better handling and looks without sacrificing ride quality. Dinan BMW springs are carefully engineered to work within your car's suspension travel and to improve suspension geometry. Spring rates are slightly stiffer than stock and dialed in to reduce bodyroll. A stiffer suspension makes the car more fun to drive and the lower ride height improves the looks by reducing wheel-fender gap.

Dinan spring specs -

• F: 1/8" (3mm)
  
• R: 1/8" (3mm)

Fitment note: When used with stock shocks the Dinan Ride Quality Kit is strongly recommended. The Kit consists of shorter and stiffer bump stops and spring perches that work better with the lowered ride height of these springs. While not explicitly required, less than favorable ride quality and handling may result without them.

For over 35 years, Dinan has been America's premier tuning company, pioneering advancements in BMW modification while retaining a focus on balanced performance that preserves the original character and driving feel that a BMW offers. When you install a Dinan part on your car, know that it's not only carefully developed and tested, but that Dinan stands behind it with a four year, 50,000-mile warranty. Dinan believes so fully in their “total package” approach that once your car has been fitted with enough of their parts, they celebrate your conversion from stock to Dinan with an exclusive trunk badge, displayed proudly by BMW enthusiasts everywhere. The springs are worth 2 points towards your Dinan badge (Ride Quality Kit is worth 1 point).

This item fits the following BMWs:
2007-2013 E93 BMW 328i - Convertible

Dinan Performance Springs are matched to your BMW's chassis and suspension components to deliver better handling and looks without sacrificing ride quality. Dinan BMW springs are carefully engineered to work within your car's suspension travel and to improve suspension geometry. Spring rates are slightly stiffer than stock and dialed in to reduce bodyroll. A stiffer suspension makes the car more fun to drive and the lower ride height improves the looks by reducing wheel-fender gap. This spring set is two front coil springs and two rear ride height sensor rods.

Dinan spring specs -

• F: -5/8" (16mm)
  
• R: -3/4" (19mm)

Fitment note: When used with stock shocks the Dinan Ride Quality Kit is strongly recommended. The Kit consists of shorter and stiffer bump stops and spring perches that work better with the lowered ride height of these springs. While not explicitly required, less than favorable ride quality and handling may result without them.

For over 35 years, Dinan has been America's premier tuning company, pioneering advancements in BMW modification while retaining a focus on balanced performance that preserves the original character and driving feel that a BMW offers. When you install a Dinan part on your car, know that it's not only carefully developed and tested, but that Dinan stands behind it with a four year, 50,000-mile warranty. Dinan believes so fully in their “total package” approach that once your car has been fitted with enough of their parts, they celebrate your conversion from stock to Dinan with an exclusive trunk badge, displayed proudly by BMW enthusiasts everywhere. The springs are worth 2 points towards your Dinan badge (Ride Quality Kit is worth 1 point).

This item fits the following BMWs:
2016+ F85 BMW2016+ F86 BMW

Dinan Performance Springs are matched to your BMW's chassis and suspension components to deliver better handling and looks without sacrificing ride quality. Dinan BMW springs are carefully engineered to work within your car's suspension travel and to improve suspension geometry. Spring rates are slightly stiffer than stock and dialed in to reduce bodyroll. A stiffer suspension makes the car more fun to drive and the lower ride height improves the looks by reducing wheel-fender gap.

Dinan spring specs -

• F: 1/2" (12mm)
  
• R: 1/2" (12mm)

Fitment note: When used with stock shocks the Dinan Ride Quality Kit is strongly recommended. The Kit consists of shorter and stiffer bump stops and spring perches that work better with the lowered ride height of these springs. While not explicitly required, less than favorable ride quality and handling may result without them.

For over 35 years, Dinan has been America's premier tuning company, pioneering advancements in BMW modification while retaining a focus on balanced performance that preserves the original character and driving feel that a BMW offers. When you install a Dinan part on your car, know that it's not only carefully developed and tested, but that Dinan stands behind it with a four year, 50,000-mile warranty. Dinan believes so fully in their “total package” approach that once your car has been fitted with enough of their parts, they celebrate your conversion from stock to Dinan with an exclusive trunk badge, displayed proudly by BMW enthusiasts everywhere. The springs are worth 2 points towards your Dinan badge (Ride Quality Kit is worth 1 point).

This item fits the following BMWs:
2007-2011 E90 BMW 335xi - Sedan

Dinan Performance Springs are matched to your BMW's chassis and suspension components to deliver better handling and looks without sacrificing ride quality. Dinan BMW springs are carefully engineered to work within your car's suspension travel and to improve suspension geometry. Spring rates are slightly stiffer than stock and dialed in to reduce bodyroll. A stiffer suspension makes the car more fun to drive and the lower ride height improves the looks by reducing wheel-fender gap.

Dinan spring specs -

• F: -3/4" (19mm)
  
• R: -1.0" (25mm)

Fitment note: When used with stock shocks the Dinan Ride Quality Kit is strongly recommended. The Kit consists of shorter and stiffer bump stops and spring perches that work better with the lowered ride height of these springs. While not explicitly required, less than favorable ride quality and handling may result without them.

For over 35 years, Dinan has been America's premier tuning company, pioneering advancements in BMW modification while retaining a focus on balanced performance that preserves the original character and driving feel that a BMW offers. When you install a Dinan part on your car, know that it's not only carefully developed and tested, but that Dinan stands behind it with a four year, 50,000-mile warranty. Dinan believes so fully in their “total package” approach that once your car has been fitted with enough of their parts, they celebrate your conversion from stock to Dinan with an exclusive trunk badge, displayed proudly by BMW enthusiasts everywhere. The springs are worth 2 points towards your Dinan badge (Ride Quality Kit is worth 1 point).

This item fits the following BMWs:
2012+ F32 BMW 435i X-Drive 440i X-Drive - Coupe

Dinan Performance Springs are matched to your BMW's chassis and suspension components to deliver better handling and looks without sacrificing ride quality. Dinan BMW springs are carefully engineered to work within your car's suspension travel and to improve suspension geometry. Spring rates are slightly stiffer than stock and dialed in to reduce bodyroll. A stiffer suspension makes the car more fun to drive and the lower ride height improves the looks by reducing wheel-fender gap.

Dinan spring specs -

• F: -3/4" (19mm)
  
• R: -3/4" (19mm)

Fitment note: When used with stock shocks the Dinan Ride Quality Kit is strongly recommended. The Kit consists of shorter and stiffer bump stops and spring perches that work better with the lowered ride height of these springs. While not explicitly required, less than favorable ride quality and handling may result without them.

For over 35 years, Dinan has been America's premier tuning company, pioneering advancements in BMW modification while retaining a focus on balanced performance that preserves the original character and driving feel that a BMW offers. When you install a Dinan part on your car, know that it's not only carefully developed and tested, but that Dinan stands behind it with a four year, 50,000-mile warranty. Dinan believes so fully in their “total package” approach that once your car has been fitted with enough of their parts, they celebrate your conversion from stock to Dinan with an exclusive trunk badge, displayed proudly by BMW enthusiasts everywhere. The springs are worth 2 points towards your Dinan badge (Ride Quality Kit is worth 1 point).

This item fits the following BMWs:
2010-2013 E70 BMW X5M
2009-2013 E71 BMW X6M

Dinan Performance Springs are matched to your BMW's chassis and suspension components to deliver better handling and looks without sacrificing ride quality. Dinan BMW springs are carefully engineered to work within your car's suspension travel and to improve suspension geometry. Spring rates are slightly stiffer than stock and dialed in to reduce bodyroll. A stiffer suspension makes the car more fun to drive and the lower ride height improves the looks by reducing wheel-fender gap.

Dinan spring specs -

• F: -1/2" (12mm)
  
• R: -1/2" (12mm)

Fitment note: When used with stock shocks the Dinan Ride Quality Kit is strongly recommended. The Kit consists of shorter and stiffer bump stops and spring perches that work better with the lowered ride height of these springs. While not explicitly required, less than favorable ride quality and handling may result without them.

For over 35 years, Dinan has been America's premier tuning company, pioneering advancements in BMW modification while retaining a focus on balanced performance that preserves the original character and driving feel that a BMW offers. When you install a Dinan part on your car, know that it's not only carefully developed and tested, but that Dinan stands behind it with a four year, 50,000-mile warranty. Dinan believes so fully in their “total package” approach that once your car has been fitted with enough of their parts, they celebrate your conversion from stock to Dinan with an exclusive trunk badge, displayed proudly by BMW enthusiasts everywhere. The springs are worth 2 points towards your Dinan badge (Ride Quality Kit is worth 1 point).

This item fits the following BMWs:
2008-2011 E90 BMW M3 Sedan