BMW Suspension Parts

Upgrade your BMW's suspension with ECS Tuning Adjustable Sway Bar End Links, designed to provide up to 60mm (2.36") of adjustability. These end links allow you to eliminate sway bar preload or fine-tune it for specific racing needs and corner balancing. When installed, they improve drivetrain clearance and enhance sway bar responsiveness by reducing deflection, ensuring superior handling. Perfect for lowered vehicles using springs, coilovers, or air-ride suspension systems, these adjustable sway bar end links allow you to remove unwanted preload caused by changes in the center-to-center distance between sway bar mounting points. By adjusting the end links to a neutral position, you eliminate sway bar preload, enhancing suspension performance in various driving conditions.

The main body of the ECS Sway Bar End Links is crafted from strong, lightweight 6061-T6 billet aluminum and anodized red for superior corrosion resistance. Featuring left and right-hand threaded center sections and machined hex wrench fittings, these end links allow for quick and easy on-the-car adjustments. Zinc-plated hardware ensures secure and lasting adjustments, while the heavy-duty ball joint ends come with weather-resistant rubber boots and stainless steel wire retainers, providing superior protection against salt, rain, and ozone for extended durability. Each kit also includes zinc-plated Nyloc nuts and hardened steel washers for secure installation and improved contact surface on the sway bar.

These end links are designed, engineered, and rigorously tested by ECS Tuning to ensure the highest quality. Whether you have a lowered or stock suspension, these adjustable sway bar end links are the perfect upgrade, offering a high-quality, heavy-duty replacement that fits your specific needs.

Features:

Range of Adjustment: 215mm (8.46") to 275mm (10.82") 6061-T6 Billet Aluminum Construction: Red anodized for superior corrosion resistance Zinc-Plated Hardware: Provides durability and superior corrosion protection Right and Left-Hand Threaded Center Sections: Quick and simple on-the-car adjustments Heavy-Duty Ball Joints(M10x1.5): Weather-resistant rubber boots and stainless steel wire retainers for long-lasting durability

Black anodized billet sway bar end links to replace your flimsy and corroded factory units. Removable hardware for a lifetime serviceable component!

Your factory end link brackets are a one piece design with an integrated stud made of flimsy metal with no coating to protect from the elements. Over the years the end link hardware rusts right to the integrated stud and when you go to remove the end links or brackets they are one strong turn and a snap away from needing to be replaced.

Not only did ECS come up with a stronger solution with a superior resistance to corrosion but went the extra mile to incorporate hardware that can be replaced time and time again so you will never need to replace the brackets themselves. The end link brackets feature chamfers and locator pins to fit perfectly in factory location and make for a straight forward install. The brackets featuring a slotted area for the bolt head to sit so you don't have the headache of having to get a wrench in the tight space behind the bracket while installing them.

Kit Contents:

A pair of rear end link brackets
Hardware needed for installation
Part Design:

Billet aluminum brackets
Zinc coated hardware
Superior corrosion resistance
Large upgrade from factory components

Due to their soft rubber construction, OE strut mounts are known to wear at an accelerated rate. Many high-mileage vehicles fall victim to strut mount failure, which is commonly associated with annoying clunks, groans, or rattles from the front suspension.

With this issue in mind, ECS Tuning developed their heavy-duty front strut mount with upgraded, higher durometer rubber to resolve sloppy handling and increase longevity. Manufactured precisely within OEM tolerances, these mounts are a perfect fit for your MINI.

Features:

Reduces deflection: Increases vehicle handling and cornering dynamics by removing deflection within the strut mount. Increases longevity: Upgraded rubber construction makes for a stiffer mount, less prone to cracking and general degradation. Developed in-house: Designed and tested by ECS Tuning engineers, this mount is sure to outlast an OE replacement. Upgrade to a better strut mount without sacrificing ride comfort! Improve longevity and ride control all at once.

Dramatically improve performance and aesthetics with an average lowering up to 1.4" front and rear.

Take your F3x to the next level with upgraded performance and aesthetic. ECS lowering springs are specifically designed with both handling and comfort in mind for the best mix or performance and drivability. With an average lowering range of 1.0"-1.4" you have the added benefit of lower center of gravity providing superior cornering and better steering feedback. Lowering springs not only increase handling performance they provide an astounding aesthetic upgrade by decreasing the wheel gap and giving your car a more planted/fitted appearance.

FEATURES AND DESIGN:

MADE IN THE USA
Average lowering of 1.0" to 1.4"
Front spring rate: 184 lbs/in
Rear spring rate: 462 lbs/in
Lowered center of gravity
Linear style springs
Black powder coating with red ECS logo
Designed specifically for your chassis these F3x lowering springs feature a linear style spring similar to a coilover. The issue with coilovers is the rough ride due to a drastic drop and much higher spring rates. When you have higher spring rate like coilovers it takes much more force to compress the spring which leads to a much more rigid ride. ECS lowering springs provide a happy medium between the factory suspension and coilover suspension. These springs are stiffer than factory but softer than a coilover spring to achieve the balance of increased performance and aesthetics while retaining a comfortable ride.

What is spring rate?
​You may ask yourself "what is the spring rate and how does it affect my ride?" Spring rate is the amount of force needed to compress a spring one inch. For example if you have a spring rate of 300lbs per inch it will take 300lbs of force to compress the spring one inch. An average coilover for your F3x has over 400 lbs/in for the front and over 500 lbs/in for the rear, this means that it will take over 400lbs of force to compress your front spring one inch and over 500lbs of force to compress the rear one inch. The higher the spring rate, the more rigid your ride is going to be. ECS lowering springs for your F3x have a spring rate of 184 lbs/in in the front and 462 lbs/in, an increase over factory but much less than a coilover. You can now both understand and explain the benefits of lowering springs to find the best solution for you.

The ECS Strut Tower Bar Kit in striking wrinkle black finish goes beyond aesthetics - it offers essential functionality. This kit significantly reduces chassis flex, contributing to a stiffer suspension setup. Moreover, it plays a crucial role in triangulating the front end, resulting in more consistent suspension geometry that enhances your vehicle's performance.

It's essential to ensure that the strut tower plates sit flush against the strut towers. Any misalignment may indicate minor deformations in your strut towers. However, this can be easily addressed using a block of wood and a hammer to reinstate the ideal alignment.

The polished aluminum ECS strut tower bar kit offers more than just good looks - it reduces chassis flex to stiffen the suspension, and helps to triangulate the front end, providing more consistent suspension geometry.

Strut tower plates should sit flush against the strut towers. If this is not the case, your strut towers are to some extent deformed. This can be easily remedied in minor cases with a block of wood and a hammer.

Upgrade your Mini's suspension with ALTA Adjustable Front Endlinks for the R55, R56, R57, R58, and R59 models. These endlinks allow for precise adjustment, optimizing your vehicle's handling and performance. Crafted with durability in mind, they offer enhanced stability and control, especially during aggressive driving. Installation is straightforward, making it easy to achieve the perfect setup for your Mini.

• Enhances suspension performance
• Allows for precise adjustment
• Improves handling and stability
• Durable construction for long-lasting reliability
• Easy installation process

Due to their soft rubber construction, OE strut mounts are known to wear at an accelerated rate. Many high-mileage vehicles fall victim to strut mount failure, which is commonly associated with annoying clunks, groans, or rattles from the front suspension.

With this issue in mind, ECS Tuning developed their heavy-duty front strut mount with upgraded, higher durometer rubber to resolve sloppy handling and increase longevity. Manufactured precisely within OEM tolerances, these mounts are a perfect fit for your BMW.

Features:

Reduces deflection: Increases vehicle handling and cornering dynamics by removing deflection within the strut mount. Increases longevity: Upgraded rubber construction makes for a stiffer mount, less prone to cracking and general degradation. Developed in-house: Designed and tested by ECS Tuning engineers, this mount is sure to outlast an OE replacement. Upgrade to a better strut mount without sacrificing ride comfort! Improve longevity and ride control all at once.

Strut mounts can begin to wear and fail over time, causing a knock in the suspension to occur. Replace yours with a high-quality Meyle replacement to ensure a tight, noise-free ride.

As a leading source of high-performance BMW parts and accessories since 1993, we at Turner Motorsport are honored to be the go-to supplier for tens of thousands of enthusiasts the world over. With over two decades of parts, service, and racing experience under our belt, we provide only quality performance and replacement parts. All of our performance parts are those we would (and do!) install and run on our own cars, as well as replacement parts that are Genuine BMW or from OEM manufacturers. We only offer parts we know you can trust to perform!

Elevate your driving experience with enhanced performance and aesthetics. ECS lowering springs are crafted to optimize both handling and comfort, striking the perfect balance between performance and drivability. With an average lowering range of 1.6", enjoy the benefits of a lower center of gravity, resulting in superior cornering and enhanced steering feedback. Not only do these lowering springs improve handling, but they also deliver a remarkable aesthetic transformation by reducing the wheel gap, giving your car a more planted and fitted appearance.

The example pictures shown are of both xDrive(Red F22) and Rwd(Blue F22)

Features and Design:

Average FRONT lowering of 1.0" - 1.4"
Average REAR lowering of 1.2" - 1.6"
Lowered center of gravity
Compatible with cars equipped with EDC
Linear style springs
Black powder coating with red ECS logo
MADE IN THE USA
Designed specifically for your chassis these ECS lowering springs feature a linear style spring similar to a coilover. The issue with coilovers is the rough ride due to a drastic drop and much higher spring rates. When you have a higher spring rate like coilovers, it takes much more force to compress the spring, leading to a much more rigid ride. ECS lowering springs provide a happy medium between the factory suspension and coilover suspension. Our springs are stiffer than factory but softer than a coilover spring to achieve the balance of increased performance and aesthetics while retaining a comfortable ride.

Full set of black anodized billet sway bar end links to replace your flimsy and corroded factory units. Removable hardware for a lifetime serviceable component!

Your factory end link brackets are a one piece design with an integrated stud made of flimsy metal with no coating to protect from the elements. Over the years your end link hardware rusts right to the integrated stud and when you go to remove the end links or brackets they are one strong turn and a snap away from needing to be replaced.

Not only did ECS come up with a stronger solution with a superior resistance to corrosion but went the extra mile to incorporate hardware that can be replaced time and time again so you will never need to replace the brackets themselves. The end link brackets feature chamfers and locator pins to fit perfectly in factory location and make for a straight forward install. The brackets featuring a slotted area for the bolt head to sit so you don't have the headache of having to get a wrench in the tight space behind the bracket while installing them.

Kit Contents:

A set of front and rear end link brackets
Hardware needed for installation
Part Design:

Billet aluminum brackets
Zinc coated hardware
Superior corrosion resistance
Large upgrade from factory components