If you are looking for a wider range of camber adjustability in the rear of you car, the IRP Adjustable rear lower control arm is exactly what you need! Built to be much stronger than stock, these rear control arms feature inner monoball bushings and are built of steel, reducing the weight as well. These are perfect for a lowered car or for a track car that needs a greater level of rear adjustment.
Features:
This item fits the following BMWs:
1992-1999 E36 BMW 318i 318is 318ic 323is 323ic 325i 325is 325ic 328i 328is 328ic M3
1999-2006 E46 BMW 323i 323ci 325i 325ci 325xi 328i 328ci 330i 330ci 330xi M3
2003-2008 E85 BMW Z4 2.5i Z4 3.0i Z4 3.0si Z4 M Roadster M Coupe
This product was last offered at the strikethrough price on
05-03-2026
This product was last offered at the strikethrough price on
05-03-2026
Looking to stiffen up your rear shock mount without going for a solid rear mount? The Polyurethane Rear Performance Strut Mount from IRP will give you the stiffer reinforcement without giving you the typical noise, vibration, and harshness that come with traditional performance strut mounts. The polyurethane also helps with preventing rear shock blowouts, a common problem for stock BMW rear mounts that are paired with stiffer than stock suspension.
The bearing sleeve and poly bushing are built to work with all stock style shocks such as Bilstein and H&R coilover and suspension kits.
Fits the following BMW chassis:
E36 BMW All Submodels except for 318ti
E46 BMW All Submodels
E30 BMW All Submodels
E36 Z3 BMW All Submodels
E85/E86 Z4 BMW All Submodels
**For vehicles with stock style springs**
When looking to dial in your steering geometry and alignment for reduced tire where and/or better track handling, the stock suspension is quite limited. To fix this, you can install Camber/Caster plates such as these plates from IRP. Camber/Caster plates allow for adjustment of the top position of the shock's mounting position. These slight adjustments have a huge impact on the stance of the of the wheel when driving straight down the road and when turning into a corner. With simple adjustments, you can increase the grip of the tires in hard turns, improve tread life, or even just make an alignment correction for a vehicle with a lowered ride height.
The IRP Camber Caster plates are made of an aircraft grade aluminum body, for strength and low weight, with an adjustable mounting plate that utilizes a steel monoball mounting point. This makes the plate resistant to corrosion and prevents deformation even with the stiffest shocks and springs.
Features:
Fits the following BMWs:
1991-1999 E36 BMW
**For vehicles with coilover front suspension**
When looking to dial in your steering geometry and alignment for reduced tire where and/or better track handling, the stock suspension is quite limited. To fix this, you can install Camber/Caster plates such as these plates from IRP. Camber/Caster plates allow for adjustment of the top position of the shock's mounting position. These slight adjustments have a huge impact on the stance of the of the wheel when driving straight down the road and when turning into a corner. With simple adjustments, you can increase the grip of the tires in hard turns, improve tread life, or even just make an alignment correction for a vehicle with a lowered ride height.
The IRP Camber Caster plates are made of an aircraft grade aluminum body, for strength and low weight, with an adjustable mounting plate that utilizes a steel monoball mounting point. This makes the plate resistant to corrosion and prevents deformation even with the stiffest shocks and springs.
Features:
Fits the following BMWs:
1991-1999 E36 BMW
A strut tower brace adds additional reinforcement to the front strut towers, tying them together for extra rigidity. This makes the whole structure stronger with less chassis flex. Handling and steering feel are improved with better turn-in and input with no downsides.
The IRP adjustable strut brace bar is a high quality brace that is constructed of 100% steel for guaranteed reinforcement and prevention of flex. The brace bar is painted black to ensure corrosion protection and to add to the looks of the engine bay.
Easily installed with basic hand tools.
Fits the following BMW chassis:
E46 BMW All Submodels
**For vehicles with coilover front suspension**
When looking to dial in your steering geometry and alignment for reduced tire where and/or better track handling, the stock suspension is quite limited. To fix this, you can install Camber/Caster plates such as these plates from IRP. Camber/Caster plates allow for adjustment of the top position of the shock's mounting position. These slight adjustments have a huge impact on the stance of the of the wheel when driving straight down the road and when turning into a corner. With simple adjustments, you can increase the grip of the tires in hard turns, improve tread life, or even just make an alignment correction for a vehicle with a lowered ride height.
The IRP Camber Caster plates are made of an aircraft grade aluminum body, for strength and low weight, with an adjustable mounting plate that utilizes a steel monoball mounting point. This makes the plate resistant to corrosion and prevents deformation even with the stiffest shocks and springs.
Features:
Fits the following BMWs:
1999-2006 E46 BMW
A strut tower brace adds additional reinforcement to the front strut towers, tying them together for extra rigidity. This makes the whole structure stronger with less chassis flex. Handling and steering feel are improved with better turn-in and input with no downsides.
The IRP adjustable strut brace bar is a high quality brace that is constructed of 100% steel for guaranteed reinforcement and prevention of flex. The brace bar is painted black to ensure corrosion protection.
Easily installed with basic hand tools.
*Does not fit convertible chassis"
Fits the following BMW chassis:
E36 BMW All Submodels
A strut tower brace adds additional reinforcement to the front strut towers, tying them together for extra rigidity. This makes the whole structure stronger with less chassis flex. Handling and steering feel are improved with better turn-in and input with no downsides.
The IRP adjustable strut brace bar is a high quality brace that is constructed of 100% steel for guaranteed reinforcement and prevention of flex. The brace bar is painted black to ensure corrosion protection and to add to the looks of the engine bay.
Easily installed with basic hand tools.
Fits the following BMW chassis:
E30 BMW All Submodels
**For vehicles with stock style springs**
When looking to dial in your steering geometry and alignment for reduced tire where and/or better track handling, the stock suspension is quite limited. To fix this, you can install Camber/Caster plates such as these plates from IRP. Camber/Caster plates allow for adjustment of the top position of the shock's mounting position. These slight adjustments have a huge impact on the stance of the of the wheel when driving straight down the road and when turning into a corner. With simple adjustments, you can increase the grip of the tires in hard turns, improve tread life, or even just make an alignment correction for a vehicle with a lowered ride height.
The IRP Camber Caster plates are made of an aircraft grade aluminum body, for strength and low weight, with an adjustable mounting plate that utilizes a steel monoball mounting point. This makes the plate resistant to corrosion and prevents deformation even with the stiffest shocks and springs.
Features:
Fits the following BMWs:
1999-2006 E46 BMW
This product was last offered at the strikethrough price on
03-23-2026
A strut tower brace adds additional reinforcement to the front strut towers, tying them together for extra rigidity. This makes the whole structure stronger with less chassis flex. Handling and steering feel are improved with better turn-in and input with no downsides.
The IRP adjustable strut brace bar is a high quality brace that is constructed of 100% steel for guaranteed reinforcement and prevention of flex. The brace bar is painted black to ensure corrosion protection and to add to the looks of the engine bay.
Easily installed with basic hand tools.
Fits the following BMW chassis:
E34 BMW All Submodels
A strut tower brace adds additional reinforcement to the front strut towers, tying them together for extra rigidity. This makes the whole structure stronger with less chassis flex. Handling and steering feel are improved with better turn-in and input with no downsides.
The IRP adjustable strut brace bar is a high quality brace that is constructed of 100% steel for guaranteed reinforcement and prevention of flex. The brace bar is painted black to ensure corrosion protection.
Easily installed with basic hand tools.
*Does not fit convertible chassis"
Fits the following BMW chassis:
E46 BMW All Submodels
When an E9X is lowered beyond the limits of just lowering springs, the rear wheels toe-in excessively. This excessive rear toe leads to premature wear, that many people attribute to an increase in negative camber. It has become a common belief that an extremely low vehicle will wear the tires wrong as a matter of consequence. It has become standard practice to go as low as you can and proceed to replace your tires every five to ten thousand miles. Whats more is that when the vehicle reaches a certain ride height, the factory arms become maxed out and there is no way to compensate and dial in the proper toe. You're left with an improperly aligned vehicle that is in effect worse off than it was with the stock suspension installed.
This is not only uneconomical but improper and unsafe. ECS Tuning is proud to offer a solution for this problem in the form of Rogue Engineering E9X adjustable rear toe arms. These arms allow for greater toe adjustment on vehicles that have been lowered with a coilover suspension. With the toe set properly the tires can contact the road properly this maximizes grip and minimizes wear.
Features:
Updated design! Now shipping!
When an E9X is lowered beyond the limits of just lowering springs, the rear wheels toe-in excessively. This excessive rear toe leads to premature wear, that many people attribute to an increase in negative camber. It has become a common belief that an extremely low vehicle will wear the tires wrong as a matter of consequence. It has become standard practice to go as low as you can and proceed to replace your tires every five to ten thousand miles. Whats more is that when the vehicle reaches a certain ride height, the factory arms become maxed out and there is no way to compensate and dial in the proper toe. You're left with an improperly aligned vehicle that is in effect worse off than it was with the stock suspension installed.
This is not only uneconomical but improper and unsafe. ECS Tuning is proud to offer a solution for this problem in the form of Rogue Engineering E9X adjustable rear toe arms. These arms allow for greater toe adjustment on vehicles that have been lowered with a coilover suspension. With the toe set properly the tires can contact the road properly this maximizes grip and minimizes wear.
Features:
100% machined and anodized, 6061-T6 lightweight aluminum arms (and collars).
Stainless hardware and spacers are perfect for the tough Northeast climate!
New! Easy adjustment with 22mm open ended wrench and 5mm allen key! It only requires 15 ft. lbs. on the clamp to secure the clamp!
New! Included lock-out kit, replaces factory eccentric hardware.
Updated 3-piece rod ends features 4130 chromoly steel bodies, heat-treated, alloy steel races, and Teflon liners
Extremely easy installation and adjustment (your alignment shop will LOVE you!)
A strut tower brace adds additional reinforcement to the front strut towers, tying them together for extra rigidity. This makes the whole structure stronger with less chassis flex. Handling and steering feel are improved with better turn-in and input with no downsides.
The IRP adjustable strut brace bar is a high quality brace that is constructed of 100% steel for guaranteed reinforcement and prevention of flex. The brace bar is painted black to ensure corrosion protection and to add to the looks of the engine bay.
Easily installed with basic hand tools.
Fits the following BMW chassis:
E36 BMW All Submodels
Want the best performance option in shock tower mounts? IRP has created their pillow-ball rear shock mounts for just this need. These rear shock mounts are designed for use on the track and racing. This set of mounts will help your rear shocks perform the best they can in all conditions. The advantage to using a mount with spherical bearing is that it allows the shock to freely move off axis without side loading the shock shaft like rubber or polyurethane mounts do. Side loading a shock increases stiction and wear which decreases its efficiency. Because these are mounts without an isolator (rubber or polyurethane) to dampen road noise and vibrations we do not recommend them for street cars.
The bearing sleeve and poly bushing are built to work with all stock style shocks such as Bilstein and H&R coilover and suspension kits.
Fits the following BMW chassis:
E36 BMW All Submodels except for 318ti
E46 BMW All Submodels
E30 BMW All Submodels
E36 Z3 BMW All Submodels
E85/E86 Z4 BMW All Submodels
A strut tower brace adds additional reinforcement to the front strut towers, tying them together for extra rigidity. This makes the whole structure stronger with less chassis flex. Handling and steering feel are improved with better turn-in and input with no downsides.
The IRP adjustable strut brace bar is a high quality brace that is constructed of 100% steel for guaranteed reinforcement and prevention of flex. The brace bar is painted black to ensure corrosion protection.
Easily installed with basic hand tools.
*Does not fit convertible chassis"
Fits the following BMW chassis:
E30 BMW All Submodels
Looking to upgrade your front suspension to increase the strength and your steering angle for the track? IRP has you covered with their BMW Lock Kit. This kit includes new control arms that are stronger than stock and have monoball ball joints, new tie rod ends that feature steel monoball ball joints as well, new offset control arm bushings, fully adjustable camber plates, roll center/bump steer correction plates, and all new hardware. This enables this kit to be fully plug and play, giving you a much more adjustable front suspension, and increases the total amount of steering angle up to 65 degrees.
This kit is perfect for those looking to build a drift car and ensure their suspension is ready to take on the challenge.
Kit features:
Fits the following BMWs:
1999-2006 E46 BMW All Non-M RWD Submodels
Looking to upgrade your front suspension to increase the strength and your steering angle for the track? IRP has you covered with their BMW Lock Kit. This kit includes new control arms that are stronger than stock and have monoball ball joints, new tie rod ends that feature steel monoball ball joints as well, new offset control arm bushings, fully adjustable camber plates, roll center/bump steer correction plates, and all new hardware. This enables this kit to be fully plug and play, giving you a much more adjustable front suspension, and increases the total amount of steering angle up to 65 degrees.
This kit is perfect for those looking to build a drift car and ensure their suspension is ready to take on the challenge.
Kit features:
Fits the following BMWs:
1999-2006 E46 BMW M3
Rogue Engineering E82/E9X Adjustable Rear Camber Link Set V2.0 is the ultimate upgrade for BMW enthusiasts seeking enhanced handling, improved tire wear, and precise suspension tuning. This high-performance solution is engineered to fit BMW E82 1-Series and E9X 3-Series models, offering superior adjustability and durability over OEM components. Ideal for street and track use, this camber link set is crafted from premium materials to ensure strength and long-lasting performance.
Key Features:
These replace the wishbone and guide arm links in the factory suspension which have rubber bushings and limited adjustment. Enhanced suspension adjustability for optimized alignment Improves handling and reduces uneven tire wear Compatible with BMW E82 1-Series and E9X 3-Series models Constructed from high-strength materials for durability and reliability Perfect for both street performance and track applications Turner Motorsport proudly offers the Rogue Engineering E82/E9X Adjustable Rear Camber Link Set V2.0, providing BMW drivers with unmatched performance and precision.
Looking to upgrade your front suspension to increase the strength and your steering angle for the track? IRP has you covered with their BMW Lock Kit. This kit includes new control arms that are stronger than stock and have monoball ball joints, new tie rod ends that feature steel monoball ball joints as well, new offset control arm bushings, fully adjustable camber plates, roll center/bump steer correction plates, and all new hardware. This enables this kit to be fully plug and play, giving you a much more adjustable front suspension, and increases the total amount of steering angle up to 65 degrees.
This kit is perfect for those looking to build a drift car and ensure their suspension is ready to take on the challenge.
Kit features:
Fits the following BMWs:
1982-1991 E30 BMW All RWD Submodels
