BMW Suspension Parts

If you are concerned about strut tower mushrooming and looking for improved handling, the M7 Strut Tower Brace (STB) is the solution. This is the ONLY strut tower brace on the market that features anti-mushrooming technology.

Repeatedly, we've heard the same complaint: strut towers mushroom after heavy impacts from shocks and low aspect ratio tires. Initially, the shock towers take on a barely visible convex shape, but if compared to the original sheet metal, you'll find the horizontal plane has moved as much as 3/8" upwards, making alignment nearly impossible.

This issue often shows up as a slight pull to the left or right, depending on which strut tower is affected. The M7 Strut Tower Brace's end mounting plates solve this problem by sandwiching the sheet metal and shock top plate, creating a reinforced surface that won't bend, even during hard impacts.

The M7 STB features 1/2" (13mm) thick end plates that add extra strength to the strut towers, preventing mushrooming and potentially costly repairs. The cross brace significantly improves handling by adding torsional stiffness to the front body structure, helping keep your tires planted and pointed in the direction you want to go, especially during hard turns. Machined from billet aluminum and matte black powder coated, the M7 Strut Tower Brace boasts a durable black finish that looks great and won't chip or oxidize.

We have customers who won't drive their new MINI off the lot without one and dealers that sell every new MINI with either the M7 Strut Reinforcement Plates or the M7 Strut Tower Brace.

Concerned about clearance? No worries. The M7 STB profile is designed to clear both stock and aftermarket cold air intakes and ECUs. Its modular design allows easy access to the oil filter or any other accessories that might normally be blocked and require removal of the entire brace.

Installation is a snap (often taking less than 20 minutes)! No need for new nuts—the brace uses the three stock nuts on each side. Installation instructions are available online by clicking the "INSTALLATION" link on this page.

The M7 Strut Reinforcement Plates and the M7 Strut Tower Brace are two separate products that address strut tower mushrooming (you only need one or the other).

If your MINI is mainly a daily driver, the M7 Strut Reinforcement Plates are sufficient. If you have performance driving in mind, the M7 Strut Tower Brace is what you're looking for!

Please note:

• You cannot buy the SRPs and attach the cross-bar at a later time.
• The brace does not directly fit on the R50 and R52 Non-"S" Cooper due to limited hood clearance of the non-supercharged cars. It will fit but may push up on the hood slightly, requiring molding or cutting of the hood insulation after installation.
• Trimming of the underhood insulation material may be required to fully clear this brace. This is a very tight space.

Strut mounts can begin to wear and fail over time, causing a knock in the suspension to occur. Replace yours with a high-quality Meyle replacement to ensure a tight, noise-free ride.

As a leading source of high-performance BMW parts and accessories since 1993, we at Turner Motorsport are honored to be the go-to supplier for tens of thousands of enthusiasts the world over. With over two decades of parts, service, and racing experience under our belt, we provide only quality performance and replacement parts. All of our performance parts are those we would (and do!) install and run on our own cars, as well as replacement parts that are Genuine BMW or from OEM manufacturers. We only offer parts we know you can trust to perform!

The front control arm bushings is the Achilles heel on the E39 models. The original factory bushings are fluid filled and rely on the fluid to absorb vibration and resist deflection. When the fluid is gone the rubber left over cannot match the original bushing's strength. The left over rubber is not stiff enough to resist the movements from the suspension. The result is a lot of vibration and reduced feedback and response from the steering.

Meyle has addressed this issue with bushings that are not fluid-filled. The bushing is made of solid rubber that will last longer than the original bushing and is a bit stiffer than new originals for better response and feel. The lack of play from the solid rubber design will mean sharper steering, restoring much of the car's precision and 'connected' feel.

This is a package of Meyle HD control arms with the HD bushings already pressed in. This makes for an easy swap out-swap in install. These arms replace the existing stock upper control arms - otherwise known as a tension strut or strut support arm. It's the arm with the twist. The BMW part numbers for these arms are 31 12 1 141 717 and 31 12 1 141 718.

Meyle is a German brand in business since 1958 and all of their products are TUV approved and meet or exceed ISO standards. All Meyle HD parts come with a 4-year, unlimited mileage warranty.

Features:

• 4 Year Warranty

• All metal ball joints are more reliable and longer lasting than stock

• Bushings are solid rubber rather than fluid filled, providing longevity and handling feel improvements

This item fits the following BMWs:
1997-2003 E39 5 Series BMW 525i, 525iT, 528i, 528iT, 530i sedans and touring wagons
2000-2003 E52 Z8 Z8 - Z8 Alpina