BMW Suspension Parts

Worn or broken sway bar end links can significantly impact your vehicle's handling, preventing the sway bar from functioning properly. Restore your suspension performance with a high-quality OE replacement sway bar end link from Bremmen. Upgrading to new end links reduces body roll, improves cornering, and enhances overall driving dynamics—an excellent way to refresh your suspension system.

Common signs of failing sway bar end links include loose handling in corners, knocking noises, and a sloppy feel when driving over bumps. Fortunately, replacing them is straightforward and can be done by any automotive enthusiast.

If you are concerned about strut tower mushrooming and looking for improved handling, the M7 Strut Tower Brace (STB) is the solution. This is the ONLY strut tower brace on the market that features anti-mushrooming technology.

Repeatedly, we've heard the same complaint: strut towers mushroom after heavy impacts from shocks and low aspect ratio tires. Initially, the shock towers take on a barely visible convex shape, but if compared to the original sheet metal, you'll find the horizontal plane has moved as much as 3/8" upwards, making alignment nearly impossible.

This issue often shows up as a slight pull to the left or right, depending on which strut tower is affected. The M7 Strut Tower Brace's end mounting plates solve this problem by sandwiching the sheet metal and shock top plate, creating a reinforced surface that won't bend, even during hard impacts.

The M7 STB features 1/2" (13mm) thick end plates that add extra strength to the strut towers, preventing mushrooming and potentially costly repairs. The cross brace significantly improves handling by adding torsional stiffness to the front body structure, helping keep your tires planted and pointed in the direction you want to go, especially during hard turns. Machined from billet aluminum and matte black powder coated, the M7 Strut Tower Brace boasts a durable black finish that looks great and won't chip or oxidize.

We have customers who won't drive their new MINI off the lot without one and dealers that sell every new MINI with either the M7 Strut Reinforcement Plates or the M7 Strut Tower Brace.

Concerned about clearance? No worries. The M7 STB profile is designed to clear both stock and aftermarket cold air intakes and ECUs. Its modular design allows easy access to the oil filter or any other accessories that might normally be blocked and require removal of the entire brace.

Installation is a snap (often taking less than 20 minutes)! No need for new nuts—the brace uses the three stock nuts on each side. Installation instructions are available online by clicking the "INSTALLATION" link on this page.

The M7 Strut Reinforcement Plates and the M7 Strut Tower Brace are two separate products that address strut tower mushrooming (you only need one or the other).

If your MINI is mainly a daily driver, the M7 Strut Reinforcement Plates are sufficient. If you have performance driving in mind, the M7 Strut Tower Brace is what you're looking for!

Please note:

• You cannot buy the SRPs and attach the cross-bar at a later time.
• The brace does not directly fit on the R50 and R52 Non-"S" Cooper due to limited hood clearance of the non-supercharged cars. It will fit but may push up on the hood slightly, requiring molding or cutting of the hood insulation after installation.
• Trimming of the underhood insulation material may be required to fully clear this brace. This is a very tight space.

Swapping in E46 control arms into your E30 or E36 significantly increases negative camber by widening the track width and also gives you more clearance for more steering angle. Condor's CNC machined control arm brackets are made from solid steel and are fitted with a solid hex-shaped bushing. Designed for the street or the track, they hold the control arm steady and eliminate "shimmy" caused by stock bushings. They sharpen steering and improve overall driving feel. Comparable to the NLA Treehouse E36 & E30 Eyeball Arms.

Easiest install of any aftermarket solution
Allow clearance for E30 M50 Conversion exhaust
Street Approved, marginal increase in NVH
Easy Installation, no need for a press
CNC machined steel construction
Solid design without the maintenance of spherical bearings
Heavy-Duty replaceable UHMW insert. Don't be misinformed, UHMW is the best material for these inserts. Delrin is not self-lubricating and will crack and degrade over time.
Powder coated white for corrosion resistance
Improve caster with M3 offset geometry
Keep proper steering geometry under high loads
Made in the U.S.A.
Fitment:
E30 84-91 3 Series
E36 92-98 3 series & Z3

Note that you will need to use E36 outer tie rods and E90 inner tie rods when installing in an E30 or E36

Be sure to measure your control arms to determine if you need 21mm or 23mm. Meyle makes a standard e46 control arm and a Heavy Duty control arm. Most HD arms have a hex that is larger in size (23mm). Lifetime Warranty