BMW Suspension Parts

Enhance your BMW's performance and appearance with CTS Turbo's high-quality lowering springs. Manufactured using durable SAE 9254/DIN 54SiCr6 Spring Steel Wire, these springs guarantee safety, strength, and resistance to fatigue over time.

• Designed for street use, focusing on handling, braking, and responsiveness without compromising ride comfort
• Engineered in-house and extensively tested to ensure no detrimental effects on the OEM strut over long-term use
• Lowers the car for an aggressive appearance, reducing wheel gap while maintaining daily drivability
• DCC compatible, seamlessly working with dynamic damper control for consistent ride characteristics across different modes

Lowering Specs:

• Front: Approximately 1.6" lowering
• Rear: Approximately 1.5" lowering

Benefits:

• Improved handling and ride quality
• Sportier aesthetic appeal with reduced fender gap
• Precision-tuned spring rates for optimal performance

Note: CTS suspension components should be installed by a qualified licensed mechanic experienced in suspension installations. Final ride height settles after a few days of driving.

When an E9X is lowered beyond the limits of just lowering springs, the rear wheels toe-in excessively. This excessive rear toe leads to premature wear, that many people attribute to an increase in negative camber. It has become a common belief that an extremely low vehicle will wear the tires wrong as a matter of consequence. It has become standard practice to go as low as you can and proceed to replace your tires every five to ten thousand miles. Whats more is that when the vehicle reaches a certain ride height, the factory arms become maxed out and there is no way to compensate and dial in the proper toe. You're left with an improperly aligned vehicle that is in effect worse off than it was with the stock suspension installed.

This is not only uneconomical but improper and unsafe. ECS Tuning is proud to offer a solution for this problem in the form of Rogue Engineering E9X adjustable rear toe arms. These arms allow for greater toe adjustment on vehicles that have been lowered with a coilover suspension. With the toe set properly the tires can contact the road properly this maximizes grip and minimizes wear. 

Features:

• 100% machined and anodized, 6061-T6 lightweight aluminum arms
• High-strength, 3-piece, rod end (with carbon fiber reinforced, PTFE race) offers longer life for street compared to standard rod ends
• SEALS-IT Rod end seals keep dirt, water, and other contaminants out
• Rod ends feature grease fittings, to allow for rod end serviceability.
• Lighter than stock!  (Stock is 875g, RE arms are 640g)
• Extremely easy installation and adjustment (your alignment shop will LOVE you!)

The MMX Performance adjustable drop links are a great choice for any lowered or hard-driven BMW to zero the pre-load on your anti-roll bar geometry. Plus, by replacing the stock rubber joints with motorsport-spec ball joint ends, you'll add valuable stiffness and precision to handling and steering dynamics.

The sway bar end link attaches the front anti-roll bar ends to the front damper. The OEM links were made the length they are for a reason, to complement the standard ride height.

When your ride height is altered, your vehicle's anti-roll bar ends are pulled up. With around 40mm of adjustable length, plus left and right threaded ends for easy length adjustment, the MMX adjustable sway bar end links allow you to adjust back to zero preload on your anti-roll bar - allowing it to operate exactly as it should once again.

Motorsport-spec ball joint ends using high-strength Teflon-lined steel means a much more direct response when turning into corners. By replacing the soft rubber bushing in the factory links with these motorsport-spec ball joints, cornering and steering responses are immediately sharpened. Importantly, rubber dust boots are fitted to protect the joints from road dirt and salt accumulation.

The lightweight CNC-machined T6-6061 aluminum bodies are anodized in our beautiful MMX gloss black coating to look good and stay looking good.

Features:

Manufactured in the UK from Aircraft grade T6-6061 aluminum billet.

Complete OE replacements

Anodized in signature MMX Gloss black.

Heavy-duty ball joints to ensure a long life span.

325-365mm adjustment range.

Direct replacement – can be used with either factory or Aftermarket rear anti-roll bar, and returned to standard at any time.

Designed with one aim in mind: to help achieve optimum suspension performance and geometric accuracy, and thus increase the effectiveness of your rear anti-roll bar.

Each heavy-duty, high-articulation rear end link attaches the rear anti-roll bar ends to the lower suspension arm. Replacing the failure-prone, weak plastic OEM links with our rigid billet aluminum links greatly reduces flex and allows a sharp, uncompromised transfer of suspension movement through to the sway bar.

As well as the link itself, extra stiffness and precision comes from replacing the flex-prone stock plastic ball joint with motorsport-spec ball joints. An especially valuable upgrade on older, higher mileage car.

Features:

Manufactured from Aircraft grade T6-6061 aluminum billet.

Complete OE replacements.

Our single-threaded ends make for easy length adjustment in-situ without having to detach and re-attach.

Each heavy-duty, high-articulation rear drop link.

Anodized in signature MMX Gloss black.

Heavy-duty ball joints to ensure a long life span.

Kit complete with everything you need.

Can be used with either factory or Aftermarket rear anti-roll bar, and returned to standard at any time.

Rubber boots for longevity and durability.