This product was last offered at the strikethrough price on
05-07-2026
This product was last offered at the strikethrough price on
07-14-2026
This product was last offered at the strikethrough price on
05-07-2026
This product was last offered at the strikethrough price on
08-13-2026
This product was last offered at the strikethrough price on
03-05-2026
This product was last offered at the strikethrough price on
06-29-2026
This product was last offered at the strikethrough price on
06-29-2026
This product was last offered at the strikethrough price on
06-29-2026
This product was last offered at the strikethrough price on
06-29-2026
When an E9X is lowered beyond the limits of just lowering springs, the rear wheels toe-in excessively. This excessive rear toe leads to premature wear, that many people attribute to an increase in negative camber. It has become a common belief that an extremely low vehicle will wear the tires wrong as a matter of consequence. It has become standard practice to go as low as you can and proceed to replace your tires every five to ten thousand miles. Whats more is that when the vehicle reaches a certain ride height, the factory arms become maxed out and there is no way to compensate and dial in the proper toe. You're left with an improperly aligned vehicle that is in effect worse off than it was with the stock suspension installed.
This is not only uneconomical but improper and unsafe. ECS Tuning is proud to offer a solution for this problem in the form of Rogue Engineering E9X adjustable rear toe arms. These arms allow for greater toe adjustment on vehicles that have been lowered with a coilover suspension. With the toe set properly the tires can contact the road properly this maximizes grip and minimizes wear.
Features:
Over the years, the road takes a serious toll on your suspension. Pot holes, speed bumps, and road hazards all contribute to a sloppy, weak suspension. To give a better feel to your driving experience, change components as they wear to improve safety and ride comfort.
One item to replace is the control arm. After years of service, the non-serviceable ball joints and other components can begin to wear out. Because some components cannot be replaced, the only solution is replacement of the entire arm.
If replacing any part of your front or rear suspension, it is best to either do it in pairs (both left and right sides), or examine parts that are prone to failure. This will provide the most service life out of replacement parts and assure they are all performing properly.
Referred to as a wishbone by BMW.
Updated design! Now shipping!
When an E9X is lowered beyond the limits of just lowering springs, the rear wheels toe-in excessively. This excessive rear toe leads to premature wear, that many people attribute to an increase in negative camber. It has become a common belief that an extremely low vehicle will wear the tires wrong as a matter of consequence. It has become standard practice to go as low as you can and proceed to replace your tires every five to ten thousand miles. Whats more is that when the vehicle reaches a certain ride height, the factory arms become maxed out and there is no way to compensate and dial in the proper toe. You're left with an improperly aligned vehicle that is in effect worse off than it was with the stock suspension installed.
This is not only uneconomical but improper and unsafe. ECS Tuning is proud to offer a solution for this problem in the form of Rogue Engineering E9X adjustable rear toe arms. These arms allow for greater toe adjustment on vehicles that have been lowered with a coilover suspension. With the toe set properly the tires can contact the road properly this maximizes grip and minimizes wear.
Features:
100% machined and anodized, 6061-T6 lightweight aluminum arms (and collars).
Stainless hardware and spacers are perfect for the tough Northeast climate!
New! Easy adjustment with 22mm open ended wrench and 5mm allen key! It only requires 15 ft. lbs. on the clamp to secure the clamp!
New! Included lock-out kit, replaces factory eccentric hardware.
Updated 3-piece rod ends features 4130 chromoly steel bodies, heat-treated, alloy steel races, and Teflon liners
Extremely easy installation and adjustment (your alignment shop will LOVE you!)
