BMW Suspension Parts

KMAC Stage 1 Street Front Adjustable Camber/Caster Plates - E36, E39 ...

T#:389645

Part#: 192416-1J

In Stock

$ 380.00 USD

Add to Wish List

Qty

$ 380.00 USD

Add to Wish List

Location: Front
Type: Street, Stage 1
Bearing: captive-ball fully encased in polyurethane

These front adjustable camber/caster plates will replace your stock front upper strut bearing. The KMAC plates are a 'floating' design so camber and caster are adjusted together. This design allows maximum range of adjustment since no other hardware interferes with the adjustments. Since these replace your stock strut bearings they are designed to work with a stock-type spring only. And when installed correctly will not significantly alter ride height. Adjustment is easily done by loosening the three nuts on top of the tower and sliding the camber plate into the position you want, then re-tighten the nuts. These mounts can be installed two ways - for camber correction or swapped side-side for increasing negative camber. Detailed instructions included.

Note: suspensions vary from manufacturer to manufacturer. Turner Motorsport cannot be responsible for fitment issues caused by non-stock or specialized coil-over suspensions. As with any race-derived component, additonal fabrication may be required.

This item fits the following BMWs:
2008-2012 E82 BMW 128i 135i
6/1992-1999 E36 BMW 318i 318is 318ti 318ic 323is 323ic 325i 325is 325ic 328i 328is 328ic M3
1999-2005 E46 BMW 323i 323ci 325i 325ci 325xi 328i 328ci 330i 330ci 330xi
2006-2011 E90 BMW 325i 328i 330i 335d 335i - Sedan
2006-2012 E91 BMW 328i - Wagon
2007-2013 E92 BMW 328i 335i 335is - Coupe
2007-2013 E93 BMW 328i 335i - Convertible
1997-2003 E39 BMW 525i 528i 530i 540i (not for cars with EDC)
2004-2010 E60 BMW 525i 530i 528i 535i 545i 550i
2004-2011 E63 E64 BMW 645ci 650i
1997-2002 Z3 BMW Z3 1.9 Z3 2.3 Z3 2.5i Z3 2.8 Z3 3.0i M Roadster M Coupe
2003-2008 E85 BMW Z4 2.5i Z4 3.0i Z4 3.0si
2009+ Z4 BMW Z4 sDrive28i Z4 sDrive30i Z4 sDrive35i Z4 sDrive35is
2000-2003 E52 BMW Z8 Roadster (without EDC)

Show More Show Less

Revshift Billet Aluminum Rear Trailing Arms - BMW E9X E8X (including ...

T#:1105927

Part#: BTA-E9X

Ships in 3 Business Days

$ 249.99 USD

Add to Wish List

Qty

$ 249.99 USD

Add to Wish List

These billet aluminum rear trailing arms fit the BMW E9x and E8x including the M models. They are CNC machined from 6061-T6 aluminum and are protected by a black anodized hardcoat. These trailing arms replace the flimsy stamped oem part, stiffen the rear suspension, and improve the vehicle's handling. Revshift Performance Engineering is a high-performance parts manufacturer with a focus on quality, reliability, and performance. Utilizing high-precision machining technologies and their very own Polyurethane Manufacturing Department, every Revshift product is designed, manufactured, and tested in-house at their Detroit, Michigan facility.

Show More Show Less

Macht Schnell EDC Emulation Module

T#:5351

Part#: TMS5351

Ships on Sep 3, 2026

$ 249.99

This product was last offered at the strikethrough price on
05-29-2026

$ 249.00 USD

Add to Wish List

Qty

$ 249.00 USD

Add to Wish List

For those wanting to move away from EDC for aftermarket suspension systems or coilover setups, the EDC monitoring can be a bit obtrusive as this type of monitoring is no longer required – resulting in numerous error messages thinking the system has malfunctioned. This EDC Emulation Module installs in less than 15 minutes and will fully emulate a fully active EDC environment when activated. Module can be activated/deactivated by via the integrated mini USB port within the module housing.

The Macht Schnell EDC Emulation Module is possible of the following features:

The ability to run aftermarket racing suspension/coilover setups in which EDC monitoring is not required

Compatible with iDrive and non-iDrive systems

Easy 15-minute installation process with no wire cutting

Proper emulation of the EDC monitoring system

No dealer visits or coding required after installation

Completely removable at any time

Note: The Macht Schnell EDC Emulation Module will disable the EDC monitoring system supplied by BMW. Once disabled the behavior of the car will change and the driver will need to adjust his/her skill and technique. For this reason, this module is not intended for street vehicles and its use may result in injury or even death if proper conditions and procedures are not followed.
Will not work on vehicles equiped with BMW's Dynamic Drive system.

This item fits the following BMWs:
2008-2011 E90 BMW M3 Sedan
2008-2013 E92 BMW M3 Coupe
2008-2013 E93 BMW M3 Convertible
2006-2010 E60 BMW M5
2006-2011 E63 BMW M6
2007-2013 E70 BMW X5 3.0si X5 4.8i X5 xDrive30i X5 xDrive35d X5 xDrive35i X5 xDrive48i
2008+ E71 BMW X6 xDrive35i X6 xDrive50i

Show More Show Less

Revshift Subframe Bushing & Reinforcement Combo Kit - Street ...

T#:27405530

Part#: SBRC-E46-80A

Ships in 6 Business Days

$ 249.99 USD

Add to Wish List

Qty

$ 249.99 USD

Add to Wish List

Upgrade your E46's rear subframe with the Revshift Combo Kit, featuring 80A durometer polyurethane rear subframe bushings and a comprehensive weld-in reinforcement plate kit. Designed to address the notorious cracking and ripping of rear subframe mounting points over time, this kit provides a robust solution to prevent costly damage to your vehicle.

Key Features:

Complete Solution: Includes 80A durometer polyurethane rear subframe bushings and precision laser-cut 14-gauge steel reinforcement plates for comprehensive subframe reinforcement. Prevents Damage: Weld-in reinforcement plates protect against cracks and damage to the chassis, ensuring long-term durability and stability. Enhanced Handling: Revshift polyurethane rear subframe bushings replace OEM rubber bushings, stiffening mounting points to improve handling and performance. Durable Construction: Polyurethane bushings are designed to last and do not wear out like rubber OEM bushings, providing consistent performance over time. Proper Dampening: Polyurethane bushings properly dampen the rear subframe, enhancing overall vehicle stability and control. Benefits:

Improved handling capabilities Long-lasting durability compared to OEM rubber bushings Protection against bending or cracking of subframe mounts The comprehensive kit includes all necessary components for installation Upgrade your E46's rear subframe with the Revshift Combo Kit for superior handling, durability, and protection against chassis damage. Boost your driving experience with enhanced performance and stability.

Show More Show Less

Revshift Subframe Bushing & Reinforcement Combo Kit - Track

T#:27405529

Part#: SBRC-E46-95A

Ships in 6 Business Days

$ 249.99 USD

Add to Wish List

Qty

$ 249.99 USD

Add to Wish List

Upgrade your E46's rear subframe with the Revshift Combo Kit, featuring 80A durometer polyurethane rear subframe bushings and a comprehensive weld-in reinforcement plate kit. Designed to address the notorious cracking and ripping of rear subframe mounting points over time, this kit provides a robust solution to prevent costly damage to your vehicle.

Key Features:

Complete Solution: Includes 95A durometer polyurethane rear subframe bushings and precision laser-cut 14-gauge steel reinforcement plates for comprehensive subframe reinforcement. Prevents Damage: Weld-in reinforcement plates protect against cracks and damage to the chassis, ensuring long-term durability and stability. Enhanced Handling: Revshift polyurethane rear subframe bushings replace OEM rubber bushings, stiffening mounting points to improve handling and performance. Durable Construction: Polyurethane bushings are designed to last and do not wear out like rubber OEM bushings, providing consistent performance over time. Proper Dampening: Polyurethane bushings properly dampen the rear subframe, enhancing overall vehicle stability and control. Benefits:

Improved handling capabilities Long-lasting durability compared to OEM rubber bushings Protection against bending or cracking of subframe mounts The comprehensive kit includes all necessary components for installation Upgrade your E46's rear subframe with the Revshift Combo Kit for superior handling, durability, and protection against chassis damage. Boost your driving experience with enhanced performance and stability.

Show More Show Less

Polyurethane Rear Trailing Arm Bushings - E36/E46

T#:582005

Part#: PTABE6GREEN

Ships in 1 Business Day

$ 79.99 USD

Add to Wish List

Qty

$ 79.99 USD

Add to Wish List

Utilizing high-precision machining technologies and their very own Polyurethane Manufacturing Department, every Revshift product is designed, manufactured, and tested in-house at their Detroit, Michigan facility.

Show More Show Less

Revshift Rear Shock Mount Kit - 80A - BMW E30 E36 E46 Z3

For shocks with a standard 10mm pin diameter

T#:1105924

Part#: RSM-E6-10MM

In Stock

$ 99.99 USD

Add to Wish List

Qty

$ 99.99 USD

Add to Wish List

Revshift rear shock mounts are CNC machined from 6061 billet aluminum and hard anodized black for protection. They are fitted with our highest quality 80A polyurethane bushings and chromoly sleeves. The class 10.9 hardware is zinc plated for corrosion resistance. These rear shock mounts can be rebuilt with one of our refresh kits sold separately. Fitment: BMW E30, E36, E46, Z3, and Z4. All OEM and aftermarket rear shocks with 10mm threads.

Show More Show Less

Polyurethane Rear Subframe Bushings - E36

T#:582007

Part#: PSBE36GREEN

Ships in 3 Business Days

$ 159.99 USD

Add to Wish List

Qty

$ 159.99 USD

Add to Wish List

Utilizing high-precision machining technologies and their very own Polyurethane Manufacturing Department, every Revshift product is designed, manufactured, and tested in-house at their Detroit, Michigan facility.

Show More Show Less

Polyurethane Rear Trailing Arm Bushings - Revshift-95A (Street/Track ...

T#:582006

Part#: PTABE30GREEN

In Stock

$ 79.99

This product was last offered at the strikethrough price on
08-12-2026

$ 72.99 USD

Limited Qty Sale

Add to Wish List

Qty

$ 79.99

This product was last offered at the strikethrough price on
08-12-2026

$ 72.99 USD

Limited Qty Sale

Add to Wish List

Utilizing high-precision machining technologies and their very own Polyurethane Manufacturing Department, every Revshift product is designed, manufactured, and tested in-house at their Detroit, Michigan facility.

Show More Show Less

Burger Motorsports Billet Strut Cross Braces - Blue - G20 M340i 330i,...

T#:637422

Part#: BMSG20BSCB-BLUE

Ships on Sep 1, 2026

$ 199.00 USD

Add to Wish List

Qty

$ 199.00 USD

Add to Wish List

Constructed from lightweight billet aluminum with the BMS logo engraved on the top middle. These strut braces are a solid one-piece design. These give an exclusive look under the hood and extra stabilization to the chassis.

Show More Show Less

Control Arm Bushings - Revshift-80A (OEM - Black)

T#:582015

Part#: PCABE30BLACK

Ships in 1 Business Day

$ 49.99 USD

Add to Wish List

Qty

$ 49.99 USD

Add to Wish List

Utilizing high-precision machining technologies and their very own Polyurethane Manufacturing Department, every Revshift product is designed, manufactured, and tested in-house at their Detroit, Michigan facility.

Show More Show Less

Burger Motorsports Billet Strut Cross Braces - Red - G20 M340i 330i, ...

T#:637421

Part#: BMSG20BSCB-RED

Ships on Sep 1, 2026

$ 199.00 USD

Add to Wish List

Qty

$ 199.00 USD

Add to Wish List

Constructed from lightweight billet aluminum with the BMS logo engraved on the top middle. These strut braces are a solid one-piece design. These give an exclusive look under the hood and extra stabilization to the chassis.

Show More Show Less

Polyurethane Rear Subframe Bushings - E36

T#:582008

Part#: PSBE36BLACK

Ships in 2 Business Days

$ 159.99 USD

Add to Wish List

Qty

$ 159.99 USD

Add to Wish List

Utilizing high-precision machining technologies and their very own Polyurethane Manufacturing Department, every Revshift product is designed, manufactured, and tested in-house at their Detroit, Michigan facility.

Show More Show Less

BMS Billet Strut Cross Braces - Anodized Blue - BMW G01 X3, G02 X4, F...

T#:39126850

Part#: BMSBILSCB-BLU

In Stock

$ 249.00 USD

Add to Wish List

Qty

$ 249.00 USD

Add to Wish List

Burger Motorsports' Billet Strut Cross Braces are designed and made in the USA from billet aluminum in a solid one-piece design. These braces connect from the strut towers to the front radiator support, helping to reinforce your entire front end while also giving your BMW an exclusive under-hood appearance.

Show More Show Less

KMAC Adjustable Rear Camber And Toe Bushings Set - E82, E89, E9X non-...

T#:389667

Part#: 193926K

In Stock

13% off MSRP $ 480.00

MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.

$ 417.00 USD

Limited Qty Sale

Add to Wish List

Qty

13% off MSRP

$ 480.00

MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.

$ 417.00 USD

Limited Qty Sale

Add to Wish List

Rear adjustable camber and toe bushings for the E82/E9X non-M 3-series. These bushings allow you to adjust camber and toe beyond factory specs to either restore camber or add more. If you lowered your car and have too much camber these bushings can get you back to stock specs. On the flip side if you need more camber for the track or autocross, you can fine tune it with these too. These bushings press in and replace the existing rubber bushings. They are made from peformance urethane which will give more feedback and response to the driver. Sold as a set with a bushing extraction tool included.

Fits the following BMWs:
E82/88 BMW 2 Series
E89 BMW Z4
E9X BMW Non-M

Show More Show Less

KMAC Stage 1 Street Front Adjustable Camber/Caster Plates - E39 540/M...

T#:389661

Part#: 193616-1J

Ships on Sep 11, 2026

$ 380.00 USD

Add to Wish List

Qty

$ 380.00 USD

Add to Wish List

Location: Front
Type: Street, Stage 1
Bearing: captive-ball fully encased in polyurethane

These front adjustable camber/caster plates will replace your stock front upper strut bearing. The KMAC plates are a 'floating' design so camber and caster are adjusted together. This design allows maximum range of adjustment since no other hardware interferes with the adjustments. Since these replace your stock strut bearings they are designed to work with a stock-type spring only. And when installed correctly will not significantly alter ride height. Adjustment is easily done by loosening the three nuts on top of the tower and sliding the camber plate into the position you want, then re-tighten the nuts. These mounts can be installed two ways - for camber correction or swapped side-side for increasing negative camber. Detailed instructions included.

Note: suspensions vary from manufacturer to manufacturer. Turner Motorsport cannot be responsible for fitment issues caused by non-stock or specialized coil-over suspensions. As with any race-derived component, additonal fabrication may be required.

This item fits the following BMWs:
1997-2003 E39 BMW 525i 528i 530i 540i (for cars with EDC)
1999-2003 E39 BMW M5
1995-2001 E38 BMW 740i 740il 750il (for cars with EDC)

Show More Show Less

Revshift Rear Shock Mount Kit - 80A - BMW E30 E36 E46 Z3

For shocks with a larger 12mm pin diameter

T#:1105925

Part#: RSM-E6-12MM

Ships in 2 Business Days

$ 99.99 USD

Add to Wish List

Qty

$ 99.99 USD

Add to Wish List

Revshift rear shock mounts are CNC machined from 6061 billet aluminum and hard anodized black for protection. They are fitted with our highest quality 80A polyurethane bushings and chromoly sleeves. The class 10.9 hardware is zinc plated for corrosion resistance. These rear shock mounts can be rebuilt with one of our refresh kits sold separately. Fitment: BMW E30, E36, E46, Z3, and Z4. All OEM and aftermarket rear shocks with 12mm threads.

Show More Show Less

Polyurethane Rear Subframe Bushings - E30

T#:1105916

Part#: PSB-E3095A

Ships in 7 Business Days

$ 89.99 USD

Add to Wish List

Qty

$ 89.99 USD

Add to Wish List

Utilizing high-precision machining technologies and their very own Polyurethane Manufacturing Department, every Revshift product is designed, manufactured, and tested in-house at their Detroit, Michigan facility.

Show More Show Less

Burger Motorsports Billet Strut Cross Braces - Black - G20 M340i 330i...

T#:637424

Part#: BMSG20BSCB-BLK

Ships in 7 Business Days

$ 199.00 USD

Add to Wish List

Qty

$ 199.00 USD

Add to Wish List

Constructed from lightweight billet aluminum with the BMS logo engraved on the top middle. These strut braces are a solid one-piece design. These give an exclusive look under the hood and extra stabilization to the chassis.

Show More Show Less

Rear Polyurethane Bushing Kit - E30

T#:1105909

Part#: RBK-E3095A

Ships in 5 Business Days

$ 199.99 USD

Add to Wish List

Qty

$ 199.99 USD

Add to Wish List

Utilizing high-precision machining technologies and their very own Polyurethane Manufacturing Department, every Revshift product is designed, manufactured, and tested in-house at their Detroit, Michigan facility.

Show More Show Less

Full Polyurethane Bushing Kit - E36

T#:1105899

Part#: FBK-E36C95A

Ships in 5 Business Days

$ 379.99 USD

Add to Wish List

Qty

$ 379.99 USD

Add to Wish List

Utilizing high-precision machining technologies and their very own Polyurethane Manufacturing Department, every Revshift product is designed, manufactured, and tested in-house at their Detroit, Michigan facility.

Show More Show Less

Adjustable Rear Upper/Inner Camber Bushings

T#:600206

Part#: 193926-3H

Ships on Sep 11, 2026

$ 320.00 USD

Add to Wish List

Qty

$ 320.00 USD

Add to Wish List

Nearly every car manufactured in the modern era carries a dark secret – fully-adjustable suspension has been all but eliminated in the name of cost-cutting and assembly-line efficiency. What this means for you is increased tire wear and more frequent replacement, as a “full alignment” consists only of rudimentary toe-angle adjustment. For over forty years, K-MAC has been hard at work developing a solution to this problem with patented innovations in camber/caster plates and bushing kits, allowing easy adjustment and a true “full four-wheel alignment” to be performed by any competent shop. These bushings make camber adjustments possible for the first time, and improve the ability to complete toe angle adjustments. When used in conjunction with the K-MAC Camber and Toe kit and Rear Adjustable Trailing Arms allows full adjustability of the 5 multi-link rear arms and positive location. Bolt-on installation – insertion/extraction tube included! Easily adjusted on the car with basic hand tools Unique failsafe locking hardware – set & forget! High quality elastomer compound resists binding Hardened & nickel-chrome plated centers for maximum bushing life 2x the load area of stock bushings Spiral grease grooves

Show More Show Less

K-MAC Stage 1 Street - Front Adjustable Camber/Caster Plates ...

T#:388807

Part#: 195116-1J

Ships on Sep 11, 2026

$ 380.00 USD

Add to Wish List

Qty

$ 380.00 USD

Add to Wish List

Location: Front
Type: Street, Stage 1
Bearing: captive-ball fully encased in polyurethane

These front adjustable camber/caster plates will replace your stock front upper strut bearing. The KMAC plates are a 'floating' design so camber and caster are adjusted together. This design allows maximum range of adjustment since no other hardware interferes with the adjustments. Since these replace your stock strut bearings they are designed to work with a stock-type spring only. And when installed correctly will not significantly alter ride height. Adjustment is easily done by loosening the three nuts on top of the tower and sliding the camber plate into the position you want, then re-tighten the nuts. These mounts can be installed two ways - for camber correction or swapped side-side for increasing negative camber. Detailed instructions included.

Note: suspensions vary from manufacturer to manufacturer. Turner Motorsport cannot be responsible for fitment issues caused by non-stock or specialized coil-over suspensions. As with any race-derived component, additonal fabrication may be required.

This item fits the following BMWs:
3/2002-2006 R50 MINI MINI Cooper
2005-2008 R52 MINI MINI Cooper Convertible, MINI Cooper S Convertible.
3/2002-2006 R53 MINI MINI Cooper S

Show More Show Less

BMW Motorsport Rear Sway Bar Bushing - 14-15mm - E90 E92 E82 ...

T#:3213

Part#: 33558300883

Ships on Sep 17, 2026

$ 31.99 USD

Add to Wish List

Qty

$ 31.99 USD

Add to Wish List

This is the factory BMW Motorsport Group N high performance rear sway bar / swaybar bushing for cars with a 14/15mm sway bar. This heavy duty rubber bushing is stiffer than the stock bushing to improve handling. They are great for track use - and Grand Am Cup legal! - yet can also be used on a street driven car - please note these will not be as compliant as the stock rubber bushing.

Sold Individually

This item fits the following BMWs:
2008+ E82 BMW 128i 135i
2006+ E90 BMW 325i 328i 330i 335i
2007+ E92 BMW 328i 335i 335is
2007+ E93 BMW 328i 335i

Show More Show Less

Rear Subframe Bushings/Mounts - Set - Group N Race Rubber - E82, E9X ...

T#:12076

Part#: E9X-GPN-SUBFRAME

In Stock

$ 800.00 USD

Add to Wish List

Qty

$ 800.00 USD

Add to Wish List

The E82 and E90/E92 subframes have an inherent weakness in the rear subframe - the mounts are too soft for the power and torque these cars are capable of. The subframe is the heart of a BMW's rear suspension. As torque is transmitted through the differential and axles and as the tires grip the road, the subframe mounts are working to keeping everything in line. That's a tough task to hold when torque is increased with bigger boost (335i) or even mild tweaks (M3). While the M3 subframe mounts are a great upgrade for the non-M chassis these factory BMW Motorsport subframe mounts go one step further.

These Motorsport/Group N rear subframe bushings are a direct replacement upgrade over the stock mounts. They are rubber to conform to the rules of the Group N racing class - so they are still acceptable for street use as long as extra ride harshness can be tolerated. The rear subframe has to come down from the car for these mounts to be pressed in. So now is the perfect time to do other work as well - check out our other Motorsport Race bushings or M3 upgrades.

Price is for the set of 4 mounts.

This item fits the following BMWs:
2008-2012 E82 BMW 128i 135i 1M Coupe
2006-2011 E90 BMW 325i 325xi 328i 328xi 328i xDrive 330i 330xi 335d 335i 335xi 335i xDrive M3 - Sedan
2006-2012 E91 BMW 325xi 328i 328xi 328i xDrive - Wagon
2007-2013 E92 BMW 328i 328xi 328i xDrive 335i 335is 335xi 335i xDrive M3 - Coupe
2007-2013 E93 BMW 328i 335i M3 - Convertible

Show More Show Less

KMAC Stage 1 Street Front Adjustable Camber/Caster Plates - E24, E28,...

T#:389654

Part#: 193316-1J

Special Order: No Guaranteed ETA

$ 379.99 USD

Add to Wish List

Qty

$ 379.99 USD

Add to Wish List

Location: Front
Type: Street, Stage 1
Bearing: captive-ball fully encased in polyurethane

These front adjustable camber/caster plates will replace your stock front upper strut bearing. The KMAC plates are a 'floating' design so camber and caster are adjusted together. This design allows maximum range of adjustment since no other hardware interferes with the adjustments. Since these replace your stock strut bearings they are designed to work with a stock-type spring only. And when installed correctly will not significantly alter ride height. Adjustment is easily done by loosening the three nuts on top of the tower and sliding the camber plate into the position you want, then re-tighten the nuts. These mounts can be installed two ways - for camber correction or swapped side-side for increasing negative camber. Detailed instructions included.

Note: suspensions vary from manufacturer to manufacturer. Turner Motorsport cannot be responsible for fitment issues caused by non-stock or specialized coil-over suspensions. As with any race-derived component, additonal fabrication may be required.

This item fits the following BMWs:
1984-1991 E30 BMW 318i 318is 318ic 325e 325es 325i 325ic 325is M3
1982-1988 E28 BMW 528e 533i 535i 535is M5
1993-1995 E34 BMW 525i
1982-1989 E24 BMW 633csi 635csi M6

Show More Show Less

Rear Upper Adjustable Lateral Straight Links

T#:22525950

Part#: WAS-422

In Stock

Sale - Save 21% $ 579.00

This product was last offered at the strikethrough price on
05-03-2026

$ 457.11 USD

Add to Wish List

Qty

Sale - Save 21%

$ 579.00

This product was last offered at the strikethrough price on
05-03-2026

$ 457.11 USD

Add to Wish List

Verkline is excited to introduce their Rear Upper Adjustable Lateral Straight Links, the culmination of an extensive development and testing process. These cutting-edge components have undergone a meticulous journey, including 3D laser scanning, CAD wishbone development, FEA (Finite Element Analysis) testing, and rigorous road trials. Now, enthusiasts have the opportunity to elevate their driving experience with these high-performance parts. Notable Advantages: Bump Steer and Anti-Squat Adjustability: Users can fine-tune their vehicle's bump steer and anti-squat characteristics for enhanced handling precision. Extended Camber Adjustment Range: These links provide a broader camber adjustment range, offering greater flexibility for alignment customization. Enhanced Strength and Rigidity: Verkline's design boasts increased strength and rigidity, resulting in an overall improvement in handling performance. Consistent Geometry: With no rubber components to flex, these links maintain consistent geometry during alignment adjustments, ensuring accuracy. Efficient Weight Design: Despite the additional functionality, these links maintain a weight profile similar to OEM components. Key Features: Bolt-In Kit: Installation is seamless, requiring no modifications for a hassle-free setup. Pre-Assembled Wishbone: The wishbone arrives pre-assembled with a predefined length, simplifying installation. High-Quality T45 Tubing: Verkline employs T45 tubing, directly sourced from the steel mill, to ensure durability and lightweight performance. Premium Motorsport Uniballs: These components feature high-quality motorsport uniballs for reliable and high-performance articulation. Uniball Rubber Boots: Protect against dust and water, extending the lifespan of the components. Comprehensive Mounting Kit: Everything needed for installation is included, making setup efficient and straightforward. OEM Knuckle and Subframe Compatibility: The design effortlessly integrates with existing setups. Included Components: Four T45 lightweight steel arms (two pairs) Thin locking nuts High-quality motorsport uniballs Spacer sleeves for assembling the arm with the subframe and upright Rubber uniball boots for dust protection Printed installation instructions Compatible with the following vehicles: BMW 3 Series G20 BMW 3 Series G21 BMW Z4 G29 Toyota Supra A90 Toyota Supra A91 Replaces the following part numbers: 33326878631 / 33326878632

Show More Show Less

AAF Skid Plate - E30

T#:7593092

Part#: 11629

Ships in 3 Business Days

$ 299.00 USD

Add to Wish List

Qty

$ 299.00 USD

Add to Wish List

Since 2010, Advanced Auto Fabrication has been producing and developing both parts and full fledged race cars. Their knowledge base covers a wide range of vehicles both domestic and imported. In the specific case of BMW, the team at AAF has a particular affinity for building and designing components for BMW race cars. E30 race engines can be expensive, so protect your investment! AAF's skid plates have proven their durability on the track. Made from precision cut steel plate, welded in house at AAF, and Powder coated for the most robust surface finish. The AAF E30 Skid Plate is a MUST-HAVE for all PRO3 and E30 Race cars. This skid plate does not use steering rack bolts, so the skid plate can be taken on and off without removing critical bolts or changing wheel alignment like other skid plates. Made specifically for an M20, (with a dimpled relief for the oil drain port, and strong gussets on both sides of the oil pan) but can be used on any E30. Includes a nut plate for ease of installation. Comes with all required hardware. Some drilling required.

Show More Show Less

Rear Sway Bar End Links - G20 / G29 / A90 / A91

T#:22525948

Part#: WAS-427

In Stock

$ 245.00

This product was last offered at the strikethrough price on
05-03-2026

$ 230.99 USD

Limited Qty Sale

Add to Wish List

Qty

$ 245.00

This product was last offered at the strikethrough price on
05-03-2026

$ 230.99 USD

Limited Qty Sale

Add to Wish List

Verkline is dedicated to delivering top-tier quality to enhance your driving experience. Their rear sway bar end links are the result of meticulous engineering, starting with a comprehensive 3D laser scan of your vehicle and CAD development of the wishbone. What sets their product apart is the extensive testing it undergoes, including Finite Element Analysis (FEA) and real-world road trials, ensuring you get a premium, high-performance solution. Key Advantages: User-Friendly Adjustability: Achieve precise corner weights without sway bar preload, maintaining consistent suspension heights for improved handling. Enhanced Strength and Rigidity: Enjoy a substantial increase in strength, which translates to superior handling performance. Replaceable High-Quality Uniballs: Say goodbye to the inconvenience of replacing the entire link due to ball joint wear. Our easily obtainable, high-quality uniballs make maintenance hassle-free. Outstanding Features: Bolt-In Installation: No need for vehicle modifications; our kit is designed for straightforward installation. Pre-Assembled Links: Ready to install out of the box, saving you time and effort. Robust High-Strength Pins: Precision-machined from high-strength steel for long-lasting durability. CNC Machined Turnbuckles: Crafted from 6082 T6 aluminum, ensuring top-notch quality and resilience. High-Quality Spherical Bearings and Uniballs: Offering exceptional articulation to prevent bending in any suspension setup. Uniball Rubber Boots: Provide protection against dust and water, extending the lifespan of your end links. Comprehensive Mounting Kit: Everything you need for a seamless installation is included. OEM Sway Bar and Upright Compatibility: Seamlessly integrates with your existing setup. What's Included: A pair of CNC billet 6082 aluminum front sway bar links turnbuckles (two pieces) Four CNC machined Cr-Mo uniball pins Thin locking nuts High-quality motorsport uniballs Rubber uniball boots for dust protection Printed installation instructions Compatible with: BMW 3 Series G20 BMW 3 Series G21 BMW Z4 G29 Toyota Supra A90 Toyota Supra A91 Replaces OEM Part Numbers: 33506785607 / 33506785608 48830-WAA01

Show More Show Less

Rear Upper Adjustable Lateral Bent Links - G20 / G29 / A90 / A91 ...

T#:22525951

Part#: WAS-423

Ships in 10 Business Days

$ 849.00 USD

Add to Wish List

Qty

$ 849.00 USD

Add to Wish List

Verkline proudly introduces their Rear Upper Adjustable Lateral Bent Links, the result of a comprehensive development and testing program. These cutting-edge components have undergone a meticulous journey, including 3D laser scanning, CAD wishbone development, Finite Element Analysis (FEA) testing, and rigorous road trials. Now, automotive enthusiasts can elevate their driving experience with these high-performance parts. Key Advantages: User-Friendly Camber Adjustability: Enthusiasts can effortlessly fine-tune their vehicle's camber settings, enabling precise alignment adjustments for improved handling. Enhanced Strength and Rigidity: Verkline's design ensures increased strength and rigidity, resulting in superior handling performance. Consistent Geometry: With no rubber components to flex, these links maintain unaltered geometry during alignment adjustments, ensuring precision. Efficient Weight Design: Despite the added functionality, these links maintain a weight profile similar to OEM components. Notable Features: Bolt-In Kit: Installation is straightforward, requiring no modifications, ensuring a hassle-free setup. Pre-Assembled Wishbone: The wishbone comes pre-assembled with a predefined length, simplifying the installation process. CNC Machined Arm: Expertly crafted from 6082 T6 aluminum, these arms offer superior strength and durability. High-Quality Motorsport Uniballs and Spherical Bearings: These components feature top-tier uniballs and spherical bearings, ensuring reliable and high-performance articulation. Uniball Rubber Boots: Provide protection against dust and water, extending the lifespan of the components. Comprehensive Mounting Kit: Everything required for installation is included, streamlining the setup. OEM Knuckle and Subframe Compatibility: The design seamlessly integrates with existing setups. Included Components: Two pairs of CNC billet 6082 aluminum wishbones (camber arms) Two pairs of CNC machined high-strength steel adjustment turnbuckles Thin locking nuts High-quality motorsport uniballs and spherical bearings Lightweight aluminum spacer sleeves for easy assembly of the arm with the subframe and upright Rubber uniball boots for dust protection Printed installation instructions Compatible with: BMW 3 Series G20 BMW 3 Series G21 BMW Z4 G29 Toyota Supra A90 Toyota Supra A91 Replaces OEM Part Numbers: 33326881199

Show More Show Less

Revshift Billet Aluminum Subframe Bushing Kit - BMW E9X E82

T#:1105926

Part#: ASB-E9X

Ships in 5 Business Days

$ 299.99 USD

Add to Wish List

Qty

$ 299.99 USD

Add to Wish List

Revshift billet aluminum subframe bushings completely replace the oem rubber bushings on the BMW E82, E90, E91, E92, and E93 including the M3, 1M, and XI models. These bushings solid mount the rear subframe reducing wheel hop and improving the vehicles handling capabilities. The two piece bushing design sandwiches the subframe locking it in place. It will not shift on the bushings while driving like the one piece designs allow. They are CNC machined at Revshift in the USA from 6061-T6 billet aluminum.

Show More Show Less

Control Arm Bushings - Revshift-95A (Street/Track - Green)

T#:582014

Part#: PCABE30GREEN

Ships in 7 Business Days

$ 49.99 USD

Add to Wish List

Qty

$ 49.99 USD

Add to Wish List

Utilizing high-precision machining technologies and their very own Polyurethane Manufacturing Department, every Revshift product is designed, manufactured, and tested in-house at their Detroit, Michigan facility.

Show More Show Less

Polyurethane Rear Subframe Bushings - E34

T#:1105932

Part#: PSB-E3480A

Ships in 1 Business Day

$ 119.99 USD

Add to Wish List

Qty

$ 119.99 USD

Add to Wish List

Utilizing high-precision machining technologies and their very own Polyurethane Manufacturing Department, every Revshift product is designed, manufactured, and tested in-house at their Detroit, Michigan facility.

Show More Show Less

Full Polyurethane Bushing Kit - E36 - 95A - Green - Offset Bushings ...

T#:1980634

Part#: FBKOFFSET

Ships in 7 Business Days

$ 379.99 USD

Add to Wish List

Qty

$ 379.99 USD

Add to Wish List

Stiffen your suspension and improve your handling with these Revshift upgraded suspension bushings. Improves handing Will not wear out like oem bushings Properly dampens suspension components

Burger Motorsports Billet Strut Cross Braces - Silver - G20 M340i 330...

T#:637423

Part#: BMSG20BSCB-SIL

Ships on Sep 1, 2026

$ 255.99 USD

Add to Wish List

Qty

$ 255.99 USD

Add to Wish List

Constructed from lightweight billet aluminum with the BMS logo engraved on the top middle. These strut braces are a solid one-piece design. These give an exclusive look under the hood and extra stabilization to the chassis.

Show More Show Less

T#:1105922

Part#: PSB-318TI95A

In Stock

$ 89.99

This product was last offered at the strikethrough price on
07-30-2026

$ 81.99 USD

Limited Qty Sale

Add to Wish List

Qty

$ 89.99

This product was last offered at the strikethrough price on
07-30-2026

$ 81.99 USD

Limited Qty Sale

Add to Wish List

Utilizing high-precision machining technologies and their very own Polyurethane Manufacturing Department, every Revshift product is designed, manufactured, and tested in-house at their Detroit, Michigan facility.

Show More Show Less

Burger Motorsports Billet Strut Cross Braces - Red - BMW G22/G23/G26 ...

T#:46924996

Part#: G22BSCB-RED

Ships on Sep 1, 2026

$ 199.00 USD

Add to Wish List

Qty

$ 199.00 USD

Add to Wish List

Burger Motorsports' strut braces are CNC machined from thick, lightweight billet aluminum with the BMS logo engraved on the top middle. These strut braces are a thick, solid one-piece design and give an exclusive look under the hood and extra stabilization to the chassis.

Show More Show Less

Rear Polyurethane Bushing Kit - E30 12MM Offset

T#:1105914

Part#: RBK-E3095A12MM

Ships in 7 Business Days

$ 224.99 USD

Add to Wish List

Qty

$ 224.99 USD

Add to Wish List

Utilizing high-precision machining technologies and their very own Polyurethane Manufacturing Department, every Revshift product is designed, manufactured, and tested in-house at their Detroit, Michigan facility.

Show More Show Less

Rear Spring Wishbone Bushings With Lockout Kit - G20 / G29 / A90 / A9...

T#:22492999

Part#: WAS-425

Special Order: No Guaranteed ETA

$ 199.00 USD

Add to Wish List

Qty

$ 199.00 USD

Add to Wish List

Unlock the full potential of your BMW G20, G29, and Supra A90/A91 with Verkline's rear spring wishbone bushings. This product is the culmination of extensive development and testing, featuring 3D laser scanning, CAD design, FEA analysis, and rigorous road trials. Experience a range of benefits, including: Enhanced strength and rigidity for superior handling performance Eliminate rubber deformations, preserving precise alignment during maintenance Key Features: A user-friendly bolt-in kit that requires no vehicle modifications Pre-assembled inserts for straightforward installation Included tool to prevent wishbone bending during insert replacement Precision CNC machining from durable 6082 T6 aluminum Equipped with high-quality motorsport spherical bearings Comprehensive kit with all necessary components for seamless mounting Compatible with OEM wishbone and subframe components Please note that if you use lockout plates to block wishbone movement on the subframe, it's essential to correct the camber setting within the adjustable upper bent link. What's Included: Two pairs of Verkline's CNC-machined 6082 aluminum spherical bearing housings High-quality motorsport spherical bearings Lightweight aluminum spacer sleeves for arm assembly with the subframe A tool to prevent wishbone bending during insert replacement Printed installation instructions Fits these BMW models: BMW G20 330i, M340i BMW G29 Z4 M40i, 30i Toyota Supra A90 / A91

Show More Show Less

Front Bump Steer Adjustable Tie Rod Ends - Toyota Supra A90 / A91 ...

T#:22525957

Part#: WAS-412

Ships in 10 Business Days

$ 499.00 USD

Add to Wish List

Qty

$ 499.00 USD

Add to Wish List

Verkline is proud to unveil their Front Bump Steer Adjustable Tie Rod Ends, the culmination of extensive development and rigorous testing. These cutting-edge components have undergone a meticulous journey, which includes 3D laser scanning, CAD wishbone development, Finite Element Analysis (FEA) testing, and rigorous road trials. Now, automotive enthusiasts have the opportunity to elevate their driving experience with these high-performance tie rod ends. Key Advantages: User-Friendly Length Adjustability: Enthusiasts can easily fine-tune the tie rod end's length to achieve optimal corner weights without sway bar preload, ensuring even suspension heights. Enhanced Strength and Rigidity: Verkline's design guarantees increased strength and rigidity, resulting in improved handling performance. Replaceable High-Quality Uniballs: In case of ball joint wear, there's no need to replace the entire tie rod end. Verkline utilizes easily obtainable, high-quality uniballs for convenience. Noteworthy Features: Bolt-In Kit: Installation is straightforward, requiring no modifications for a hassle-free setup. Pre-Assembled Links: The tie rod ends arrive pre-assembled, simplifying the installation process. Robust Full-Length Pins: Precision-machined from high-strength steel, these pins ensure durability and reliability. CNC Machined Turnbuckles: Crafted from 6082 T6 aluminum, these turnbuckles offer superior strength and performance. High-Quality Spherical Bearings and Uniballs: These components feature top-tier spherical bearings and uniballs, ensuring reliable and high-performance articulation. Uniball Rubber Boots: Provide protection against dust and water, extending the lifespan of the components. Complete Mounting Kit: Everything required for installation is included, streamlining the setup. OEM Sway Bar and Coil-Over Compatibility: The design seamlessly integrates with existing setups. Included Components: Two pairs of CNC billet 6082 aluminum front tie rod ends Two pairs of CNC machined Cr-Mo upright pins Thin locking nuts High-quality motorsport spherical bearings Set of pin spacers for bump steer adjustment Printed installation instructions Automotive enthusiasts can now experience the precision and performance of Verkline's Front Bump Steer Adjustable Tie Rod Ends, allowing them to enhance their vehicle's handling and alignment for a more controlled and responsive driving experience. These components are designed to be compatible with OEM sway bars and coil-over setups, providing versatility for various vehicle configurations. Compatible with the following vehicles: Toyota Supra A90 Toyota Supra A91

Show More Show Less

Polyurethane Rear Subframe Bushings - E30 325iX

T#:1105918

Part#: PSB-E30IX95A

Ships in 7 Business Days

$ 89.99 USD

Add to Wish List

Qty

$ 89.99 USD

Add to Wish List

Utilizing high-precision machining technologies and their very own Polyurethane Manufacturing Department, every Revshift product is designed, manufactured, and tested in-house at their Detroit, Michigan facility.

Show More Show Less

Polyurethane Rear Subframe Bushings - E30 12MM Offset

T#:1105917

Part#: PSB-E3012MM95A

Ships in 7 Business Days

$ 119.99 USD

Add to Wish List

Qty

$ 119.99 USD

Add to Wish List

Utilizing high-precision machining technologies and their very own Polyurethane Manufacturing Department, every Revshift product is designed, manufactured, and tested in-house at their Detroit, Michigan facility.

Show More Show Less

Revshift Polyurethane Subframe Bushings - 95A (Track - Green) - BMW E...

T#:47199273

Part#: PSB-E9X-95A

Ships in 1 Business Day

$ 249.99 USD

Add to Wish List

Qty

$ 249.99 USD

Add to Wish List

Revshift polyurethane subframe bushings completely replace the OEM rubber bushings on the BMW E82, E81, E87, E88, E90, E91, E92, and E93, including the M3, 1M, and XI models. These bushings securely mount the rear subframe, reducing wheel hop and improving the vehicle's handling capabilities. The two-piece bushing design sandwiches the subframe, locking it in place. It will not shift on the bushings while driving, like the one-piece designs allow. They are entirely made at Revshift in the USA from our proprietary polyurethane formula and CNC-machined billet aluminum cores.

Show More Show Less

Project Cars

SELECT YOUR BMW

Sub-Categories

Select Vehicle

Purpose

Category

Brand

Price

Special Offers

Shipping

Narrow Results