BMW Gaskets, Gasket Sets, Seals, & O-Rings

OE BMW replacement valve cover gasket for your leaking N54 engine.
When doing any sort of repair or maintenance there is no replacement for genuine factory parts. Turner Motorsport carries the Genuine BMW brand with pride and has the parts you need to complete your next project with confidence.

Genuine BMW Profile-Gasket
This item fits the following BMW Chassis:
E82 1M Coupe,E71 X6,E82,E89 Z4,E90,E92,E93,F01,F02

Fits BMW Engines including:
N54,N54T

Not only will this kit stop most E90 oil leaks, it's the perfect addition for ignition coil or spark plug replacement! Oil leaks - and the damage they can cause - seem to be the worst annoyances on these cars. The biggest source of an oil leak is from the valve cover, followed by the oil filter housing, Valvetronic seal, camshaft seals, and the eccentric shaft sensor seal. Once the oil leaks, and if ignored for an extended time, the oil will contaminate vital electrical sensors. This is especially the case with ignition coils and also the eccentric shaft sensor on the Valvetronic shaft at the top of the cylinder head. During any ignition coil and spark plug replacement take a close look inside for any oil pooling at the bottom. We have been seeing valve cover oil leaks as soon as 40,000 miles. We look for oil leaks on every E90 that comes into our shop.

We have put together this package of valve cover gaskets and other related gaskets and seals for you to fully overhaul the N52 valve cover and put a stop to those pesky oil leaks. This package has the replacement parts for N52 engines built up to 10/2006 and includes:
 

• 11127581215 - N52 valve cover gasket set
• 11120409288 - N52 aluminum valve cover bolts (1-time use only, not re-usable)
• 11377516302 - N52 Valvetronic gasket
• 11127528242 - N52 eccentric shaft sensor seal

These are all Genuien BMW parts. Replacement of these gaskets and seals is straight-forward but a long process. BMW dealers typically charge for over eight hours of labor. If you have replaced spark plugs before you should be capable of this repair. In addition, there are several other parts to replace while you're in the vicinity: camshaft sensor o-rings, oil filter housing profile gasket, VAN0S solenoids, and the eccentric shaft sensor. These other parts, except the eccentric shaft sensor (see below), are replaceable without removing the valve cover but are more easily accessed during the valve cover work.

Eccentric Shaft Sensor: This is the position sensor that relays the eccentric shaft's position back to the DME. It's located at the front of the engine and is only accessible with the valve cover off. Over time the seal around the sensor comes loose and oil is allowed to blow out of the cam cover and it eventually finds its way into the sensor (which will eventually fail). Without a functioning sensor your E90 can experience poor running, hesitation, poor performance, jerky shifts, and sluggish response. It's easy to check and see if oil has accumulated inside the sensor: unbolt the engine trim cover (the outer cover with the BMW roundel), unplug the sensor, and look inside. If oil is present inside or even around the sensor itself, plan on replacing this sensor during your next ignition coil, spark plug, and/or valve cover gasket work.

This valve cover kit fits the following BMWs:
2006 E90 BMW 325i 325xi 330i 330xi - Sedan
2006 E91 BMW 325xi - Wagon
2006 E60 BMW 525i 525xi 530i 530xi
2006-10/2006 E85 BMW Z4 3.0i Z4 3.0si

When doing any sort of repair or maintenance there is no replacement for genuine factory parts. Turner Motorsport carries the Genuine BMW brand with pride and has the parts you need to complete your next project with confidence.

Genuine BMW Cylinder Head Gasket Asbestos-Free - 1,20Mm
This item fits the following BMW Chassis:
E71,E82,E90,E92,E93,F06,F10,F12,F13,F15,F16,F22,F25 X3,F26 X4,F30,F32,F33,F34,F36

Fits BMW Engines including:
N55

A  leaking N52 oil filter housing gasket can cause a myriad of problems. The most prominent of which is getting oil on your serpentine belt, causing it to shred, get sucked into the engine, and cause catastrophic engine failure. This kit includes everything you need to replace on the car - gasket and bolts, since the bolts are torque to yield (1 time use).

This kit includes:
1 Oil Filter Housing Gasket (11428637821)
1 M8x28 bolt (11427540759)
1 M8x43 bolt (11427540763)
1 M8x78 bolt (11427540758)

Having done quite a few of these jobs, we recommend this E10 1/4" Drive Swivel socket to help get the job done without removing your intake manifold.

This kit is for all N52 engines.

The oil pan gasket is often a failure point in N52 and N54 engines around the 80k mile mark. We recommend replacing your oil pan gasket with a Genuine BMW gasket, so you don't have to drop your subframe more than once.

Turner Motorsport's Oil Pan Gasket Replacement Kit includes everything you need to repair your leaky oil pan:

• 7L Genuine BMW 5w-30 Oil (83212365946)
• Genuine BMW Oil Filter Kit (11427953129)
• Genuine BMW Replacement 1-time use bolt set (11132210959)
• Genuine BMW Oil Pan Gasket (11137548031)