BMW Drivetrain Parts

OEM ZF Automatic Transmission Service Kit - BMW 8HP F & G-Chassis ...

2X Entries For Our G87 M2 Sweepstakes! "For 8HP45Z, 8HP50Z, 8HP70Z, or 8HP75Z automatic transmissions"

T#:31191923

Part#: ZF8HPATSKT

In Stock

$ 287.99

This product was last offered at the strikethrough price on
04-03-2026

$ 256.99 USD

Add to Wish List

Qty

$ 256.99 USD

Add to Wish List

Over the life of a vehicle, the transmission can often be overlooked when performing routine maintenance. If left unserviced, the automatic transmission fluid will break down, causing the valve body and filter to become contaminated with deposits and sludge. This will lead to poor shifting, slipping, and ultimately, transmission failure. Kit Includes: OEM ZF Automatic transmission filter OEM ZF Oil Pan Gasket & Installation Hardware OEM ZF Drain plug with sealing washer OEM ZF Fill plug with sealing washer 7 Liters of ZF Lifeguard 8 Fluid NOTE: Depending on the model, an additional liter of fluid may be necessary if you are draining your oil cooler or removing the valve body. As per ZF's recommendations, Turner Motorspot suggests performing a full service on your 8HP automatic transmission every 50,000 miles. If your vehicle is modified and makes more power than stock or if your vehicle is regularly track-driven, we recommend shorter 30,000-mile service intervals. This will ensure your transmission's fluid is free from contamination which will help extend the life of internal transmission components like clutch packs and solenoids.

Show More Show Less

ZF Automatic Transmission Oil Pan With Transmission Filter - F22 F30 ...

2X Entries For Our G87 M2 Sweepstakes! For 8HP45Z, 8HP50Z, 8HP70Z, or 8HP75Z automatic transmissions

T#:403431

Part#: 24118612901

In Stock

$ 130.99

This product was last offered at the strikethrough price on
04-12-2026

$ 123.99 USD

Add to Wish List

Qty

$ 123.99 USD

Add to Wish List

GA8HP 8 speed automatic transmission. Automatic transmissions are reliable, shift smoothly, and can last without issue so long as they are properly maintained. Over time, the transmission fluid becomes thick and the filter becomes contaminated with small metal particles. This can cause excess wear, high transmission operating temperatures, and eventual failure. To prevent this we recommend changing your filter, fluid, and seals to ensure your transmission continues to operate flawlessly. We recommend filter and fluid changes every 50,000 miles. This item fits the following BMWs: E71,E89 Z4,F06,F10,F12,F13,F15,F16,F22,F25 X3,F26 X4,F30,F31,F32,F33,F34,F36

Show More Show Less

BMS Billet Clutch Delay Valve (CDV) Delete - E8X/E9X

T#:2513299

Part#: BMWCLUTCHVAVLE

Ships in 1 Business Day

$ 29.99 USD

Add to Wish List

Qty

$ 29.99 USD

Add to Wish List

Enhance the performance of your stick shift BMW with the BMS clutch valve, a must-have upgrade for serious BMW enthusiasts. This high-performance replacement replaces the factory clutch delay valve, resulting in quicker shifts, longer clutch life, and improved 0-60 times. Designed with CNC machined precision, it installs quickly using factory-like connections with no modifications required. Made in the USA, this clutch valve is essential for maximizing the driving experience of your BMW.

Benefits:

Replaces factory clutch delay valve for improved performance
Quicker shifts and improved 0-60 times
Longer clutch life
Easy installation with factory-like connections
Made in the USA

Show More Show Less

ZF 320 5-sp Manual Transmission Shaft Seal Set

2X Entries For Our G87 M2 Sweepstakes!

T#:16707419

Part#: ZFS5D320SEALKIT

In Stock

$ 59.99 USD

Add to Wish List

Qty

$ 59.99 USD

Add to Wish List

OEM ZF Automatic Transmission Filter Kit - GA6HP19Z - E82 E90 E92 E93...

2X Entries For Our G87 M2 Sweepstakes!

T#:596310

Part#: 24152333907

In Stock

$ 121.99 USD

Add to Wish List

Qty

$ 121.99 USD

Add to Wish List

For GA6HP19Z Automatic Transmissions

Automatic transmissions are reliable, shift smoothly, and can last without issue so long as they are properly maintained. Over time, the transmission fluid becomes thick and the filter becomes contaminated with small metal particles. This can cause excess wear, high transmission operating temperatures, and eventual failure. To prevent this we recommend changing your filter, fluid, and seals to ensure your transmission continues to operate flawlessly. We recommend filter and fluid changes every 50,000 miles.

NOTE: This filter fits GA6HP19Z automatic transmissions. This will NOT fit the GA6L45R transmission. Please check your transmission to ensure it is the correct type.

This kit contains:

(1) Oil Pan with Filter

(1) Oil Pan Gasket

(1) Filter O-Ring

(1) Drain Plug

Show More Show Less

Front Differential Bushing - Priced Each

We Price Match - Give Us A Call or Chat!

T#:362591

Part#: 33171090389

In Stock

$ 28.99

This product was last offered at the strikethrough price on
05-07-2026

$ 23.99 USD

Add to Wish List

Qty

$ 23.99 USD

Add to Wish List

Meyle Front Wheel Hub/Bearing Assembly - E30

We Price Match - Give Us A Call or Chat!

T#:370509

Part#: 31211131297

In Stock

$ 86.99 USD

Add to Wish List

Qty

$ 86.99 USD

Add to Wish List

Includes wheel bearing

Engine Mount - Priced Each

T#:594933

Part#: 11811132323

Ships in 1-2 days

$ 43.56

This product was last offered at the strikethrough price on
06-01-2026

$ 25.99 USD

Add to Wish List

Qty

$ 25.99 USD

Add to Wish List

Excessive driveline vibration is caused by one of a few things, but more than likely, it is the mounts in your vehicle. They keep your engine and transmission secure for more positive shifting and driveline triangulation as well as absorbing vibration. If any of these are occuring in your BMW, it's time to examine your mounts.

Show More Show Less

Corteco Engine Mount - Left - E38, E39

T#:362312

Part#: 22111092895

In Stock

$ 120.82

This product was last offered at the strikethrough price on
05-13-2026

$ 81.99 USD

Add to Wish List

Qty

$ 81.99 USD

Add to Wish List

Secures engine to subframe for a vibration-free connection

E36 M3, MZ3 JB Racing Lightweight Aluminum Flywheel

T#:3771

Part#: 520-010-240

Ships in 9 Business Days

$ 602.00 USD

Add to Wish List

Qty

$ 602.00 USD

Add to Wish List

Aluminum flywheels are much lighter than the stock steel flywheel and that produces better throttle response and more available horsepower to the wheels for faster acceleration. The JB Racing aluminum flywheels are a direct replacement for the stock flywheel and work with stock clutch components for an easy upgrade with very little downside.

Modern flywheels are built with additional components and features that are designed to dampen and minimize vibrations from the engine and transmission. As a result they have become bloated in weight and that means more energy is used up just making the flywheel spin. The weight difference between an aluminum and steel flywheel is huge - sometimes more than 50% less. Without the additional mass, more energy can be diverted to where it counts most - moving the car. The flywheel and clutch is one of the first areas that engine builders address when making the rotating assembly lighter for race engines. The dampening effect is just not needed on cars that are focused on performance.

In addition to releasing more power to the wheels, the lighter flywheel allows the engine to spin more freely, which improves throttle response. Again, the difference is huge as you watch the revs build faster than before. With the engine spinning easier the power band comes up much sooner. The stock steel flywheel feels lazy in comparison. There is a driving adjustment required to get used to how much faster the engine revs but that's not really a downside.

The JB lightweight flywheel is designed to be used with a factory organic clutch - the same clutch kit that you would get from any BMW dealer. This makes replacement clutch components easy to source and inexpensive when compared to specialized racing clutches. By using the factory BMW clutch, JB has also made the whole assembly easy to live with when used on the street. The clutch behaves the same as it originally did - just with better throttle response and more power! The JB flywheel can also be rebuilt with a new clutch contact surface - you don't have to buy a new flywheel.

Aluminum flywheels are considered 'single-mass' flywheels because they do not have the same dampening designs as an original 'dual-mass' flywheel. With a single-mass design more noise and vibration may be noticeable. There are steps you can take to minimize the noise - heavier weight transmission oil and clutch discs with anti-rattle springs (sprung-hub clutch). In addition to the standard replacement clutches, we also sell Sachs Performance sprung hub clutches that also work with the JB flywheels.

Stock Flywheel Weight = 25.5lbs
JB Flywheel Weight = 10.0lbs

This item fits the following BMWs:
1995-1999 E36 BMW M3
1998-2002 Z3 BMW Z3 M Roadster M Coupe

Show More Show Less

Corteco Engine Mount - Right - E38, E39

T#:362315

Part#: 22111092896

In Stock

$ 153.05

This product was last offered at the strikethrough price on
06-18-2026

$ 149.99 USD

Add to Wish List

Qty

$ 149.99 USD

Add to Wish List

Secures engine to subframe for a vibration-free connection

Meyle Rear Differential Mount - E24, E28

We Price Match - Give Us A Call or Chat!

T#:392737

Part#: 33171129784

In Stock

$ 61.99 USD

Add to Wish List

Qty

$ 61.99 USD

Add to Wish List

Replace damaged bushings to restore handling and performance to your vehicle

Automatic Transmission Service Kit - Lifeguard 6 Fluid

2X Entries For Our G87 M2 Sweepstakes!

T#:13332225

Part#: 24152333907KT

In Stock

$ 302.99

This product was last offered at the strikethrough price on
03-31-2026

$ 259.99 USD

Add to Wish List

Qty

$ 259.99 USD

Add to Wish List

Everything you need for a complete, hassle free transmission service straight from ZF.

ZF Transmission Sealing Sleeve

2X Entries For Our G87 M2 Sweepstakes!

T#:376243

Part#: 24347588725

In Stock

$ 32.27 USD

Add to Wish List

Qty

$ 32.27 USD

Add to Wish List

Connects Mechatronik control assembly to transmission

N54/N55 BMW Automatic Transmission Cooler - 335 W/Thermostat ...

T#:21045476

Part#: BMS-335-TC-WTH

Back Ordered

$ 573.00 USD

Add to Wish List

Qty

$ 573.00 USD

Add to Wish List

Everyone knows that heat is the enemy of your automatic transmission. And everyone knows that higher power levels generate more transmission fluid heat. Now you can extend the life of your automatic transmission by installing the new Burger Motorsports High Capacity Trans Cooler kit. This unique plug-and-play kit replaces your factory coolant to trans fluid heat exchanger with a high-capacity fender-mounted air-to-trans fluid radiator. Includes all mounting hardware, lines, and coolant caps required for installation. Installs inside the driverside fender providing ample airflow over the large cooling core via existing openings. The result is dramatically reduced transmission temperature and extended transmission life. This kit is strongly suggested for any BMW E chassis automatic running larger than factory turbos. The thermostat maintains the oil exiting the transmission at the rated minimum temperature in most conditions. Without a thermostat, the transmission fluid coolers are likely to over-cool the fluid, delaying transmission warm-up and performing the critical function of bypassing the cooler until the oil has reached its minimum operating temperature. FEATURES AND BENEFITS Dissipates excess transmission fluid heat Reduces transmission fluid temperature Increases transmission life when racing Increases transmission oil capacity Fitment: 2008-2013 E81 E82 E87 Coupe and Hatchback 135i 2008-2013 E88 Convertible 135i Compatible with both RHD and LHD vehicles. Not compatible with manual transmissions.

Show More Show Less

N54/N55 BMW Automatic Transmission Cooler - E9X 335

T#:1347205

Part#: N54N55TRANSCOOL

In Stock

$ 444.99

This product was last offered at the strikethrough price on
06-16-2026

$ 399.00 USD

Add to Wish List

Qty

$ 399.00 USD

Add to Wish List

Everyone knows that heat is the enemy of your automatic transmission. And everyone knows that higher power levels generate more transmission fluid heat. Now you can extend the life of your automatic transmission by installing the new Burger Motorsports High Capacity Trans Cooler kit. This unique plug-and-play kit replaces your factory coolant to trans fluid heat exchanger with a high-capacity fender-mounted air-to-trans fluid radiator. Includes all mounting hardware, lines, and coolant caps required for installation. Installs inside the driverside fender providing ample airflow over the large cooling core via existing openings. The result is dramatically reduced transmission temperature and extended transmission life. This kit is strongly suggested for any BMW E chassis automatic running larger than factory turbos. FEATURES AND BENEFITS Dissipates excess transmission fluid heat Reduces transmission fluid temperature Increases transmission life when racing Increases transmission oil capacity Fitment: 2006-2011 E90 Sedan 335i/335ix 2006-2013 E90 E91 Sedan/Touring 335d (M57 diesel) 2006-2011 E91 Touring 335i/335ix 2011-2013 E92 Coupe 335is 2007-2013 E92 Coupe 335i/335ix 2006-2013 E93 Convertible 335i/335ix Compatible with both RHD and LHD vehicles. Not compatible with manual transmissions.

Show More Show Less

E30 318i/is, E36 318i, Z3 1.9 JB Racing Lightweight Aluminum Flywheel...

T#:3769

Part#: 520-040-215

Back Ordered

11% off MSRP $ 765.00

MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.

$ 679.00 USD

Add to Wish List

Qty

11% off MSRP

$ 765.00

MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.

$ 679.00 USD

Add to Wish List

Aluminum flywheels are much lighter than the stock steel flywheel and that produces better throttle response and more available horsepower to the wheels for faster acceleration. The JB Racing aluminum flywheels are a direct replacement for the stock flywheel and work with stock clutch components for an easy upgrade with very little downside.

Modern flywheels are built with additional components and features that are designed to dampen and minimize vibrations from the engine and transmission. As a result they have become bloated in weight and that means more energy is used up just making the flywheel spin. The weight difference between an aluminum and steel flywheel is huge - sometimes more than 50% less. Without the additional mass, more energy can be diverted to where it counts most - moving the car. The flywheel and clutch is one of the first areas that engine builders address when making the rotating assembly lighter for race engines. The dampening effect is just not needed on cars that are focused on performance.

In addition to releasing more power to the wheels, the lighter flywheel allows the engine to spin more freely, which improves throttle response. Again, the difference is huge as you watch the revs build faster than before. With the engine spinning easier the power band comes up much sooner. The stock steel flywheel feels lazy in comparison. There is a driving adjustment required to get used to how much faster the engine revs but that's not really a downside.

The JB lightweight flywheel is designed to be used with a factory organic clutch - the same clutch kit that you would get from any BMW dealer. This makes replacement clutch components easy to source and inexpensive when compared to specialized racing clutches. By using the factory BMW clutch, JB has also made the whole assembly easy to live with when used on the street. The clutch behaves the same as it originally did - just with better throttle response and more power! The JB flywheel can also be rebuilt with a new clutch contact surface - you don't have to buy a new flywheel.

Aluminum flywheels are considered 'single-mass' flywheels because they do not have the same dampening designs as an original 'dual-mass' flywheel. With a single-mass design more noise and vibration may be noticeable. There are steps you can take to minimize the noise - heavier weight transmission oil and clutch discs with anti-rattle springs (sprung-hub clutch).

Stock Flywheel Weight = 27.0lbs
JB Flywheel Weight = 9.0lbs

This item fits the following BMWs:
1989-1992 E30 BMW 318i 318is 318ic
1992-1997 E36 BMW 318i 318is 318ti 318ic
1996-1997 Z3 BMW Z3 1.9

Show More Show Less

Sealing Sleeve

2X Entries For Our G87 M2 Sweepstakes!

T#:594175

Part#: 24107536340

In Stock

$ 24.39 USD

Add to Wish List

Qty

$ 24.39 USD

Add to Wish List

Found in the transmission housing

E60, E82, E85, E9X, E89 (N52 Engine) JB Racing Lightweight Aluminum F...

T#:2801

Part#: 520-200-240

In Stock

$ 714.00 USD

Add to Wish List

Qty

$ 714.00 USD

Add to Wish List

Aluminum flywheels are much lighter than the stock steel flywheel and that produces better throttle response and more available horsepower to the wheels for faster acceleration. The JB Racing aluminum flywheels are a direct replacement for the stock flywheel and work with stock clutch components for an easy upgrade with very little downside.

Modern flywheels are built with additional components and features that are designed to dampen and minimize vibrations from the engine and transmission. As a result they have become bloated in weight and that means more energy is used up just making the flywheel spin. The weight difference between an aluminum and steel flywheel is huge - sometimes more than 50% less. Without the additional mass, more energy can be diverted to where it counts most - moving the car. The flywheel and clutch is one of the first areas that engine builders address when making the rotating assembly lighter for race engines. The dampening effect is just not needed on cars that are focused on performance.

In addition to releasing more power to the wheels, the lighter flywheel allows the engine to spin more freely, which improves throttle response. Again, the difference is huge as you watch the revs build faster than before. With the engine spinning easier the power band comes up much sooner. The stock steel flywheel feels lazy in comparison. There is a driving adjustment required to get used to how much faster the engine revs but that's not really a downside.

The JB lightweight flywheel is designed to be used with a factory organic clutch - the same clutch kit that you would get from any BMW dealer. This makes replacement clutch components easy to source and inexpensive when compared to specialized racing clutches. By using the factory BMW clutch, JB has also made the whole assembly easy to live with when used on the street. The clutch behaves the same as it originally did - just with better throttle response and more power! The JB flywheel can also be rebuilt with a new clutch contact surface - you don't have to buy a new flywheel.

Aluminum flywheels are considered 'single-mass' flywheels because they do not have the same dampening designs as an original 'dual-mass' flywheel. With a single-mass design more noise and vibration may be noticeable. There are steps you can take to minimize the noise - heavier weight transmission oil and clutch discs with anti-rattle springs (sprung-hub clutch).

This JB flywheel replaces the stock flywheel and can be used with either the stock 228mm or stock 240mm clutch discs. Depending on the model you may have either clutch size in your car but this flywheel is compatible with both. You can install a 240mm clutch as a mild upgrade.

Stock Flywheel Weight = 24-31.0lbs
JB Flywheel Weight = 12.0lbs

This item fits the following BMWs:
2006-2010 E60 BMW - 525i, 528i, 530i
2006-2013 E90, E91, E92, E93 BMW - 325i, 328i, 330i
2007-2013 E82 BMW - 125i, 128i
2006-2008 E85, E86 BMW - Z4 3.0i, Z4 3.0si
2009-later E89 BMW - Z4 3.0i

Show More Show Less

E46 M3 6MT JB Racing Lightweight Aluminum Flywheel

T#:302739

Part#: 520-180-240

Ships in 8 Business Days

$ 602.00 USD

Add to Wish List

Qty

$ 602.00 USD

Add to Wish List

Aluminum flywheels are much lighter than the stock steel flywheel and that produces better throttle response and more available horsepower to the wheels for faster acceleration. The JB Racing aluminum flywheels are a direct replacement for the stock flywheel and work with stock clutch components for an easy upgrade with very little downside.

Modern flywheels are built with additional components and features that are designed to dampen and minimize vibrations from the engine and transmission. As a result they have become bloated in weight and that means more energy is used up just making the flywheel spin. The weight difference between an aluminum and steel flywheel is huge - sometimes more than 50% less. Without the additional mass, more energy can be diverted to where it counts most - moving the car. The flywheel and clutch is one of the first areas that engine builders address when making the rotating assembly lighter for race engines. The dampening effect is just not needed on cars that are focused on performance.

In addition to releasing more power to the wheels, the lighter flywheel allows the engine to spin more freely, which improves throttle response. Again, the difference is huge as you watch the revs build faster than before. With the engine spinning easier the power band comes up much sooner. The stock steel flywheel feels lazy in comparison. There is a driving adjustment required to get used to how much faster the engine revs but that's not really a downside.

The JB lightweight flywheel is designed to be used with a factory organic clutch - the same clutch kit that you would get from any BMW dealer. This makes replacement clutch components easy to source and inexpensive when compared to specialized racing clutches. By using the factory BMW clutch, JB has also made the whole assembly easy to live with when used on the street. The clutch behaves the same as it originally did - just with better throttle response and more power! The JB flywheel can also be rebuilt with a new clutch contact surface - you don't have to buy a new flywheel.

Aluminum flywheels are considered 'single-mass' flywheels because they do not have the same dampening designs as an original 'dual-mass' flywheel. With a single-mass design more noise and vibration may be noticeable. There are steps you can take to minimize the noise - heavier weight transmission oil and clutch discs with anti-rattle springs (sprung-hub clutch). In addition to the standard replacement clutches, we also sell Sachs Performance sprung hub clutches that also work with the JB flywheels.

Stock Flywheel Weight = 25.0lbs
JB Flywheel Weight = 10.0lbs

This item fits the following BMWs:
2001-2006 E46 BMW M3 (6-speed manual only, not for SMG)

Show More Show Less

Burger Motorsports Differential Support Bracket Brace - F-Chassis BMW...

T#:637547

Part#: BMS-DSBB-F

Back Ordered

Starting at $ 129.00 USD

Add to Wish List

Starting at $ 129.00 USD

Add to Wish List

The BMS differential brace attaches the rear differential to the subframe allowing better launches, less wheel hop, and a more stable feeling rear chassis. Their unique one-piece construction eliminates welding weak points common on similar units. No logos or markings are visible for a stealth OEM appearance.

Show More Show Less

OEM ZF Automatic Transmission Filter Kit - GA8HP75 GAHP76 - BMW F85/8...

2X Entries For Our G87 M2 Sweepstakes!

T#:31125616

Part#: 24007855263

Back Ordered

$ 149.99 USD

Add to Wish List

Qty

$ 149.99 USD

Add to Wish List

This is a brand new automatic transmission filter service kit directly from ZF for the GAHP75 and GAHP76 transmissions found in many of the newer BMW M cars, including the G8X M2, M3, & M4, F90 M5, F91/92/93 M8, F97 X3M, F98 X4M, F85 X5M, and F86 X6M. This kit includes all of the basic components needed to service your transmission, other than the transmission fluid. Included: Oil Pan Gasket Oil Filter Drain & Fill Plugs Oil Pan Mounting Screws (Qty 13) As per ZF's recommendations, we suggest replacing your filter and changing your fluid every 50,000 miles. If your vehicle is modified and makes more power than stock, or if your vehicle is regularly track-driven, we recommend shorter 30,000-mile service intervals. This will ensure your transmission's fluid is free from contamination which will help extend the life of internal transmission components like clutch packs and solenoids.

Show More Show Less

E46 323/325/328/330 5-speed, Z3 2.3/2.8/3.0 JB Racing Lightweight Alu...

T#:4227

Part#: 520-140-240

In Stock

$ 602.00 USD

Add to Wish List

Qty

$ 602.00 USD

Add to Wish List

Aluminum flywheels are much lighter than the stock steel flywheel and that produces better throttle response and more available horsepower to the wheels for faster acceleration. The JB Racing aluminum flywheels are a direct replacement for the stock flywheel and work with stock clutch components for an easy upgrade with very little downside.

Modern flywheels are built with additional components and features that are designed to dampen and minimize vibrations from the engine and transmission. As a result they have become bloated in weight and that means more energy is used up just making the flywheel spin. The weight difference between an aluminum and steel flywheel is huge - sometimes more than 50% less. Without the additional mass, more energy can be diverted to where it counts most - moving the car. The flywheel and clutch is one of the first areas that engine builders address when making the rotating assembly lighter for race engines. The dampening effect is just not needed on cars that are focused on performance.

In addition to releasing more power to the wheels, the lighter flywheel allows the engine to spin more freely, which improves throttle response. Again, the difference is huge as you watch the revs build faster than before. With the engine spinning easier the power band comes up much sooner. The stock steel flywheel feels lazy in comparison. There is a driving adjustment required to get used to how much faster the engine revs but that's not really a downside.

The JB lightweight flywheel is designed to be used with a factory organic clutch - the same clutch kit that you would get from any BMW dealer. This makes replacement clutch components easy to source and inexpensive when compared to specialized racing clutches. By using the factory BMW clutch, JB has also made the whole assembly easy to live with when used on the street. The clutch behaves the same as it originally did - just with better throttle response and more power! The JB flywheel can also be rebuilt with a new clutch contact surface - you don't have to buy a new flywheel.

Aluminum flywheels are considered 'single-mass' flywheels because they do not have the same dampening designs as an original 'dual-mass' flywheel. With a single-mass design more noise and vibration may be noticeable. There are steps you can take to minimize the noise - heavier weight transmission oil and clutch discs with anti-rattle springs (sprung-hub clutch). In addition to the standard replacement clutches, we also sell Sachs Performance sprung hub clutches that also work with the JB flywheels.

Stock Flywheel Weight = 25.0lbs
JB Flywheel Weight = 10.0lbs

This item fits the following BMWs:
1999-2002 E46 BMW 323i 323ci 325i 325ci 328i 328ci 330i 330ci (with 5-speed manual transmission)
2001-2005 E46 BMW 325xi 330xi
1997-2002 Z3 BMW Z3 2.3 Z3 2.5i Z3 2.8 Z3 3.0i

Show More Show Less

JB Racing Single Mass Lightweight Aluminum Flywheel - 6-speed - E46 3...

T#:3474

Part#: 520-190-240

Ships in 4 Business Days

$ 672.00 USD

Add to Wish List

Qty

$ 672.00 USD

Add to Wish List

This is a performance replacement for BMW Part # 21207533868 Aluminum flywheels are much lighter than the stock steel flywheel and that produces better throttle response and more available horsepower to the wheels for faster acceleration. The JB Racing aluminum flywheels are a direct replacement for the stock flywheel and work with stock clutch components for an easy upgrade with very little downside.

Modern flywheels are built with additional components and features that are designed to dampen and minimize vibrations from the engine and transmission. As a result they have become bloated in weight and that means more energy is used up just making the flywheel spin. The weight difference between an aluminum and steel flywheel is huge - sometimes more than 50% less. Without the additional mass, more energy can be diverted to where it counts most - moving the car. The flywheel and clutch is one of the first areas that engine builders address when making the rotating assembly lighter for race engines. The dampening effect is just not needed on cars that are focused on performance.

In addition to releasing more power to the wheels, the lighter flywheel allows the engine to spin more freely, which improves throttle response. Again, the difference is huge as you watch the revs build faster than before. With the engine spinning easier the power band comes up much sooner. The stock steel flywheel feels lazy in comparison. There is a driving adjustment required to get used to how much faster the engine revs but that's not really a downside.

The JB lightweight flywheel is designed to be used with a factory organic clutch - the same clutch kit that you would get from any BMW dealer. This makes replacement clutch components easy to source and inexpensive when compared to specialized racing clutches. By using the factory BMW clutch, JB has also made the whole assembly easy to live with when used on the street. The clutch behaves the same as it originally did - just with better throttle response and more power! The JB flywheel can also be rebuilt with a new clutch contact surface - you don't have to buy a new flywheel.

Aluminum flywheels are considered 'single-mass' flywheels because they do not have the same dampening designs as an original 'dual-mass' flywheel. With a single-mass design more noise and vibration may be noticeable. There are steps you can take to minimize the noise - heavier weight transmission oil and clutch discs with anti-rattle springs (sprung-hub clutch).

The JB Flywheel includes the pilot bearing mounted in the flywheel hub, just like the factory configuration.

Stock Flywheel Weight = 25.0lbs
JB Flywheel Weight = 10.5lbs

This item fits the following BMWs:
2002-2005 E46 BMW 325i 330i (with 6-speed manual transmission)

Show More Show Less

Rear Differential Mount - Front Position

We Price Match - Give Us A Call or Chat!

T#:594515

Part#: 33316792873

Ships in 2 Business Days

$ 41.99

This product was last offered at the strikethrough price on
05-07-2026

$ 40.99 USD

Add to Wish List

Qty

$ 40.99 USD

Add to Wish List

Over time bushings deteriorate and become ineffective. Replace them to reduce noise and harshness. Priced Each. Two required for complete service.

Differential Input Shaft Seal - Priced Each

T#:44021076

Part#: 33121213949

Ships in 2 Business Days

$ 27.99

This product was last offered at the strikethrough price on
05-07-2026

$ 26.99 USD

Add to Wish List

Qty

$ 26.99 USD

Add to Wish List

Meyle CV Boot Repair Kit - Inner - E36

We Price Match - Give Us A Call or Chat!

T#:592404

Part#: 33219067819

Ships in 1-2 days

$ 70.43 USD

Add to Wish List

Qty

$ 70.43 USD

Add to Wish List

Replace torn CV boots and save CV joints

E30 325i, E34 525i (M20) JB Racing Lightweight Aluminum Flywheel (Rep...

T#:385699

Part#: 520-060-228

Ships on Sep 1, 2026

$ 581.00 USD

Add to Wish List

Qty

$ 581.00 USD

Add to Wish List

Aluminum flywheels are much lighter than the stock steel flywheel and that produces better throttle response and more available horsepower to the wheels for faster acceleration. The JB Racing aluminum flywheels are a direct replacement for the stock flywheel and work with stock clutch components for an easy upgrade with very little downside.

Modern flywheels are built with additional components and features that are designed to dampen and minimize vibrations from the engine and transmission. As a result they have become bloated in weight and that means more energy is used up just making the flywheel spin. The weight difference between an aluminum and steel flywheel is huge - sometimes more than 50% less. Without the additional mass, more energy can be diverted to where it counts most - moving the car. The flywheel and clutch is one of the first areas that engine builders address when making the rotating assembly lighter for race engines. The dampening effect is just not needed on cars that are focused on performance.

In addition to releasing more power to the wheels, the lighter flywheel allows the engine to spin more freely, which improves throttle response. Again, the difference is huge as you watch the revs build faster than before. With the engine spinning easier the power band comes up much sooner. The stock steel flywheel feels lazy in comparison. There is a driving adjustment required to get used to how much faster the engine revs but that's not really a downside.

The JB lightweight flywheel is designed to be used with a factory organic clutch - the same clutch kit that you would get from any BMW dealer. This makes replacement clutch components easy to source and inexpensive when compared to specialized racing clutches. By using the factory BMW clutch, JB has also made the whole assembly easy to live with when used on the street. The clutch behaves the same as it originally did - just with better throttle response and more power! The JB flywheel can also be rebuilt with a new clutch contact surface - you don't have to buy a new flywheel.

Aluminum flywheels are considered 'single-mass' flywheels because they do not have the same dampening designs as an original 'dual-mass' flywheel. With a single-mass design more noise and vibration may be noticeable. There are steps you can take to minimize the noise - heavier weight transmission oil and clutch discs with anti-rattle springs (sprung-hub clutch).

This flywheel replaces the stock original single-mass flywheel and should only be used with the corresponding 'single-mass' clutch kit. According to BMW the single mass flywheel was installed in all 325i up to 12/86 production date but we have seen some later cars with a single-mass flywheel. The age of the car almost guarantees one or more clutch replacements and possibly a change to the original flywheel as well. You may not know which flywheel is currently installed until the flywheel cover or the transmission is removed.

Stock Flywheel Weight = 18.0lbs
JB Flywheel Weight = 8.0lbs

This item fits the following BMWs:
1984-1991 E30 BMW 325i 325ic 325is (with single-mass flywheel)
1989-1990 E34 BMW 525i (with single-mass flywheel)

Show More Show Less

DCT Transmission Filter & Gasket - GS7D36SG - E82/88 135i, E9X M3 335...

We Price Match - Give Us A Call or Chat!

T#:29234322

Part#: 3001360302

Ships on Oct 29, 2026

$ 57.99 USD

Add to Wish List

Qty

$ 57.99 USD

Add to Wish List

BMW claims their transmission fluid to be a "lifetime" fluid, however is recommended to be changed every 60,000 miles to ensure a longer transmission life. Though not exposed to the same level of heat and contamination as engine oil, transmission oil still breaks down over time due to heat and becomes contaminated as your transmission wears. Old contaminated oil can lead to excessive wear and tear on sensitive transmission components which could lead to slow shifting, slips, and even complete failure. This is also true for the transmission filter. The filter removes metal particles from the transmission fluid and eventually begins to clog, preventing fluid from passing through the filter easily. This leads to excessive wear and a reduced transmission lifespan if not changed. Not sure if this kit is right for your BMW? Contact our sales staff with your VIN to confirm the exact part you need.

Show More Show Less

Meyle Driveshaft Center Support - E36, E39, Z3

We Price Match - Give Us A Call or Chat!

T#:359503

Part#: 26121226731

Back Ordered

$ 34.99 USD

Add to Wish List

Qty

$ 34.99 USD

Add to Wish List

Replacement center support bearing for the driveshaft from Meyle. Often the cause of annoying vibrations and clunking noises during take-offs.

This item fits the following BMWs:
Manual Transmission
1992-1998 E36 BMW 318i 318is 318ic 323is 323ic 325is 325ic 328i 328is 328ic
12/94-1995 E36 BMW 325i Sedan
1997-2003 E39 BMW 525i 530i

Automatic Transmission
1992-1998 E36 BMW 318ti 323is 323ic 328i 328is 328ic
1998-2003 E39 BMW 525i 528i 530i
1999-2002 Z3 BMW Z3 2.5i Z3 3.0i

Show More Show Less

BMW Automatic Transmission Service Kit - Level 2 - Lifeguard 6 ATF ...

2X Entries For Our G87 M2 Sweepstakes! GA6HP26Z Service Kit

T#:13102202

Part#: 24152333903KT4

In Stock

$ 326.99

This product was last offered at the strikethrough price on
03-31-2026

$ 277.99 USD

Add to Wish List

Qty

$ 277.99 USD

Add to Wish List

BMW Automatic Transmission Service Kit - Level 2 - Lifeguard 6 is a comprehensive service solution that includes everything needed to effectively maintain and service your BMW's transmission using high-quality ZF components and fluid. While BMW suggests that the ZF transmission utilizes a lifetime fluid, it’s important to understand that “lifetime” refers to the warranty, not the transmission's operational lifespan. Over time, the fluid degrades, becoming less effective at transferring heat and lubricating internal components. This degradation can lead to premature wear, resulting in louder operation, harder shifts, and potentially severe internal damage.

ZF recommends service intervals of 50,000 miles or 8 years—whichever comes first—for 6HP transmissions. By using OEM ZF components in this kit, BMW owners can ensure that only the highest quality factory parts and fluids are used, keeping the transmission running smoothly for years to come.

Benefits:

Comprehensive Kit: Contains all necessary components for a complete transmission service, ensuring an efficient and thorough maintenance process.
High-Quality OEM Parts: Includes ZF components, guaranteeing compatibility and superior performance.
Prevents Premature Wear: Regular service helps avoid costly repairs by maintaining fluid integrity and component lubrication.
Improves Performance: Enhanced fluid conditions contribute to smoother shifting and quieter operation.
Recommended Service Intervals: Follows ZF’s guidelines for optimal maintenance, promoting longevity in your BMW’s transmission.

Show More Show Less

E34 M5 JB Racing Lightweight Aluminum Flywheel

T#:3772

Part#: 520-090-240

Ships in 7 Business Days

$ 581.00 USD

Add to Wish List

Qty

$ 581.00 USD

Add to Wish List

Aluminum flywheels are much lighter than the stock steel flywheel and that produces better throttle response and more available horsepower to the wheels for faster acceleration. The JB Racing aluminum flywheels are a direct replacement for the stock flywheel and work with stock clutch components for an easy upgrade with very little downside.

Modern flywheels are built with additional components and features that are designed to dampen and minimize vibrations from the engine and transmission. As a result they have become bloated in weight and that means more energy is used up just making the flywheel spin. The weight difference between an aluminum and steel flywheel is huge - sometimes more than 50% less. Without the additional mass, more energy can be diverted to where it counts most - moving the car. The flywheel and clutch is one of the first areas that engine builders address when making the rotating assembly lighter for race engines. The dampening effect is just not needed on cars that are focused on performance.

In addition to releasing more power to the wheels, the lighter flywheel allows the engine to spin more freely, which improves throttle response. Again, the difference is huge as you watch the revs build faster than before. With the engine spinning easier the power band comes up much sooner. The stock steel flywheel feels lazy in comparison. There is a driving adjustment required to get used to how much faster the engine revs but that's not really a downside.

The JB lightweight flywheel is designed to be used with a factory organic clutch - the same clutch kit that you would get from any BMW dealer. This makes replacement clutch components easy to source and inexpensive when compared to specialized racing clutches. By using the factory BMW clutch, JB has also made the whole assembly easy to live with when used on the street. The clutch behaves the same as it originally did - just with better throttle response and more power! The JB flywheel can also be rebuilt with a new clutch contact surface - you don't have to buy a new flywheel.

Aluminum flywheels are considered 'single-mass' flywheels because they do not have the same dampening designs as an original 'dual-mass' flywheel. With a single-mass design more noise and vibration may be noticeable.

Stock Flywheel Weight = 16.0lbs
JB Flywheel Weight = 8.0lbs

This item fits the following BMWs:
1991-1995 E34 BMW M5

Show More Show Less

BMW E9X 335i BMS Differential Support Bracket Brace - Small Case ...

T#:1316770

Part#: E9XDIFFBRACE-SM

Back Ordered

$ 99.00 USD

Add to Wish List

Qty

$ 99.00 USD

Add to Wish List

BMW E9X 335i BMS Differential Support Bracket Brace - Small Case

The BMW E9X 335i BMS Differential Support Bracket Brace - Small Case is a high-performance upgrade designed to enhance the stability and durability of the differential mount. Turner Motorsport offers this precision-engineered brace to reduce flex and movement of the differential, ensuring improved power transfer and handling. Ideal for high-performance driving or track use, this brace helps maintain proper alignment and extends the lifespan of your differential components.

Benefits:

Enhances differential stability by reducing flex and movement
Improves power transfer and handling performance
Precision-engineered for a perfect fit and reliable performance
Ideal for high-performance driving and track use
Extends the lifespan of differential components
Made from high-quality materials for durability and strength

Show More Show Less

BMS Differential Support Bracket Brace For G Chassis BMW/Supra ...

T#:49822560

Part#: BMSDSBBG

Ships on Sep 1, 2026

$ 229.00 USD

Add to Wish List

Qty

$ 229.00 USD

Add to Wish List

For G-Chassis BMW & A90/A91 Toyota Supra High torque loads, hard launches, and aggressive driving expose the factory differential mounting’s built-in compliance. Under power, the differential can shift excessively, resulting in wheel hop, inconsistent traction, and increased stress on drivetrain components—issues that become more pronounced on tuned or track-driven cars. The BMS Differential Support Bracket Brace corrects this weakness by reinforcing the differential mounting point and securely tying it to the subframe. By controlling unwanted movement, the brace improves rear-end stability and ensures power is transferred to the ground more efficiently. Why Upgrade? OEM differential mounts favor NVH reduction over control. As torque output increases, that compliance translates into drivetrain shock and lost traction. This brace stiffens the system where it matters most, reducing flex and improving load management under acceleration. Performance Benefits Improved launch consistency Significant reduction in wheel hop Increased rear-end stability under load More precise and predictable power delivery Engineered for Demanding Use Designed around factory mounting points, the BMS Differential Support Bracket delivers precise OE-level fitment with increased structural rigidity. Its robust construction resists deflection under high torque, while upgraded hardware provides greater clamping force for long-term reliability. Fully bolt-on for straightforward installation on both stock and modified vehicles. Key Features Reinforces rear differential mounting Limits differential movement under load Enhances traction and drivetrain response Heavy-duty construction for high-performance applications Bolt-on installation using factory locations Compatible with G-chassis BMW and A90/A91 Supra A focused drivetrain upgrade for drivers who demand consistency, control, and durability at higher performance levels.

Show More Show Less

2002, E21 320i, E30 318i (M10) JB Racing Lightweight Aluminum Flywhee...

T#:3647

Part#: 520-110-215

Ships in 2 Business Days

$ 581.00 USD

Add to Wish List

Qty

$ 581.00 USD

Add to Wish List

Aluminum flywheels are much lighter than the stock steel flywheel and that produces better throttle response and more available horsepower to the wheels for faster acceleration. The JB Racing aluminum flywheels are a direct replacement for the stock flywheel and work with stock clutch components for an easy upgrade with very little downside.

Modern flywheels are built with additional components and features that are designed to dampen and minimize vibrations from the engine and transmission. As a result they have become bloated in weight and that means more energy is used up just making the flywheel spin. The weight difference between an aluminum and steel flywheel is huge - sometimes more than 50% less. Without the additional mass, more energy can be diverted to where it counts most - moving the car. The flywheel and clutch is one of the first areas that engine builders address when making the rotating assembly lighter for race engines. The dampening effect is just not needed on cars that are focused on performance.

In addition to releasing more power to the wheels, the lighter flywheel allows the engine to spin more freely, which improves throttle response. Again, the difference is huge as you watch the revs build faster than before. With the engine spinning easier the power band comes up much sooner. The stock steel flywheel feels lazy in comparison. There is a driving adjustment required to get used to how much faster the engine revs but that's not really a downside.

The JB lightweight flywheel is designed to be used with a factory organic clutch - the same clutch kit that you would get from any BMW dealer. This makes replacement clutch components easy to source and inexpensive when compared to specialized racing clutches. By using the factory BMW clutch, JB has also made the whole assembly easy to live with when used on the street. The clutch behaves the same as it originally did - just with better throttle response and more power! The JB flywheel can be rebuilt too with a new clutch contact surface.

Aluminum flywheels are considered 'single-mass' flywheels because they do not have the same dampening designs as an original 'dual-mass' flywheel. With a single-mass design more noise and vibration may be noticeable. There are steps you can take to minimize the noise - heavier weight transmission oil and clutch discs with anti-rattle springs (sprung-hub clutch).

Stock Flywheel Weight = 16.5lbs
JB Flywheel Weight = 8lbs

This item fits the following BMWs:
1974-1976 2002 BMW 2002
1977-1983 E21 BMW 320i
1984-1985 E30 BMW 318i

Show More Show Less

BMS Differential Support Bracket Brace - BMW 135i / E9x 335i - Large ...

T#:1316771

Part#: E9XDIFFBRACE-LG

Ships in 1 Business Day

$ 99.00 USD

Add to Wish List

Qty

$ 99.00 USD

Add to Wish List

E30 M3 JB Racing Lightweight Aluminum Flywheel

T#:3768

Part#: 520-050-228

Ships in 4 Business Days

$ 630.00 USD

Add to Wish List

Qty

$ 630.00 USD

Add to Wish List

Aluminum flywheels are much lighter than the stock steel flywheel and that produces better throttle response and more available horsepower to the wheels for faster acceleration. The JB Racing aluminum flywheels are a direct replacement for the stock flywheel and work with stock clutch components for an easy upgrade with very little downside.

Modern flywheels are built with additional components and features that are designed to dampen and minimize vibrations from the engine and transmission. As a result they have become bloated in weight and that means more energy is used up just making the flywheel spin. The weight difference between an aluminum and steel flywheel is huge - sometimes more than 50% less. Without the additional mass, more energy can be diverted to where it counts most - moving the car. The flywheel and clutch is one of the first areas that engine builders address when making the rotating assembly lighter for race engines. The dampening effect is just not needed on cars that are focused on performance.

In addition to releasing more power to the wheels, the lighter flywheel allows the engine to spin more freely, which improves throttle response. Again, the difference is huge as you watch the revs build faster than before. With the engine spinning easier the power band comes up much sooner. The stock steel flywheel feels lazy in comparison. There is a driving adjustment required to get used to how much faster the engine revs but that's not really a downside.

The JB lightweight flywheel is designed to be used with a factory organic clutch - the same clutch kit that you would get from any BMW dealer. This makes replacement clutch components easy to source and inexpensive when compared to specialized racing clutches. By using the factory BMW clutch, JB has also made the whole assembly easy to live with when used on the street. The clutch behaves the same as it originally did - just with better throttle response and more power! The JB flywheel can also be rebuilt with a new clutch contact surface - you don't have to buy a new flywheel.

Aluminum flywheels are considered 'single-mass' flywheels because they do not have the same dampening designs as an original 'dual-mass' flywheel. With a single-mass design more noise and vibration may be noticeable. There are steps you can take to minimize the noise - heavier weight transmission oil and clutch discs with anti-rattle springs (sprung-hub clutch).

The JB flywheel includes ignition trigger wheel.

Stock Flywheel Weight = 19.5lbs
JB Flywheel Weight = 8.0lbs

This item fits the following BMWs:
1987-1991 E30 BMW M3

Show More Show Less

Rear Wheel Bearing

We Price Match - Give Us A Call or Chat!

T#:5282919

Part#: 33416792361

In Stock

$ 53.99

This product was last offered at the strikethrough price on
08-10-2026

$ 44.99 USD

Limited Qty Sale

Add to Wish List

Qty

$ 53.99

This product was last offered at the strikethrough price on
08-10-2026

$ 44.99 USD

Limited Qty Sale

Add to Wish List

The Rear Wheel Bearing facilitates smooth wheel rotation by minimizing friction, ensuring quiet operation. It improves stability, handling, and overall driving performance.

Corteco Output Shaft Seal - E10, E21

T#:592386

Part#: 33121205302

In Stock

$ 28.99 USD

Add to Wish List

Qty

$ 28.99 USD

Add to Wish List

Seals the axles into the differential

Automatic Transmission Oil Pan With Transmission Filter - GA8P75HZ - ...

We Price Match - Give Us A Call or Chat! For vehicles with a ZF GA8P75HZ automatic transmission only

T#:29201103

Part#: 3003250010

In Stock

Sale - Save 40% $ 207.99

This product was last offered at the strikethrough price on
05-03-2026

$ 125.00 USD

Add to Wish List

Qty

Sale - Save 40%

$ 207.99

This product was last offered at the strikethrough price on
05-03-2026

$ 125.00 USD

Add to Wish List

BMW claims their transmission fluid to be a "lifetime" fluid, however is recommended to be changed every 60,000 miles to ensure a longer transmission life. Though not exposed to the same level of heat and contamination as engine oil, transmission oil still breaks down over time due to heat and becomes contaminated as your transmission wears. Old contaminated oil can lead to excessive wear and tear on sensitive transmission components which could lead to slow shifting, slips, and even complete failure. This is also true for the transmission filter integrated into the transmission fluid pan. The filter removes metal particles from the transmission fluid and eventually begins to clog, preventing fluid from passing through the filter easily. This leads to excessive wear and a reduced transmission lifespan if not changed. This high-quality Meyle transmission pan includes a new filter and is quintessential for a correct and full service. Not sure if this kit is right for your BMW? Contact our sales staff with your VIN to confirm the exact part you need.

Show More Show Less

Corteco Transmission Mount - E60

T#:592084

Part#: 22316771741

In Stock

$ 41.99

This product was last offered at the strikethrough price on
04-06-2026

$ 21.99 USD

Add to Wish List

Qty

$ 21.99 USD

Add to Wish List

Replace your worn transmission mounts

E39 540i 97-03 JB Racing Lightweight Aluminum Flywheel

T#:1339

Part#: 520-150-240

In Stock

$ 903.00 USD

Add to Wish List

Qty

$ 903.00 USD

Add to Wish List

Aluminum flywheels are much lighter than the stock steel flywheel and that produces better throttle response and more available horsepower to the wheels for faster acceleration. The JB Racing aluminum flywheels are a direct replacement for the stock flywheel and work with stock clutch components for an easy upgrade with very little downside.

Modern flywheels are built with additional components and features that are designed to dampen and minimize vibrations from the engine and transmission. As a result they have become bloated in weight and that means more energy is used up just making the flywheel spin. The weight difference between an aluminum and steel flywheel is huge - sometimes more than 50% less. Without the additional mass, more energy can be diverted to where it counts most - moving the car. The flywheel and clutch is one of the first areas that engine builders address when making the rotating assembly lighter for race engines. The dampening effect is just not needed on cars that are focused on performance.

In addition to releasing more power to the wheels, the lighter flywheel allows the engine to spin more freely, which improves throttle response. Again, the difference is huge as you watch the revs build faster than before. With the engine spinning easier the power band comes up much sooner. The stock steel flywheel feels lazy in comparison. There is a driving adjustment required to get used to how much faster the engine revs but that's not really a downside.

The JB lightweight flywheel is designed to be used with a factory organic clutch - the same clutch kit that you would get from any BMW dealer. This makes replacement clutch components easy to source and inexpensive when compared to specialized racing clutches. By using the factory BMW clutch, JB has also made the whole assembly easy to live with when used on the street. The clutch behaves the same as it originally did - just with better throttle response and more power! The JB flywheel can also be rebuilt with a new clutch contact surface - you don't have to buy a new flywheel.

Aluminum flywheels are considered 'single-mass' flywheels because they do not have the same dampening designs as an original 'dual-mass' flywheel. With a single-mass design more noise and vibration may be noticeable. There are steps you can take to minimize the noise - heavier weight transmission oil and clutch discs with anti-rattle springs (sprung-hub clutch).

Stock Flywheel Weight = 33.0lbs
JB Flywheel Weight = 13.0lbs

This item fits the following BMWs:
1997-2003 E39 BMW 540i

Show More Show Less

Corteco Transmission Mount - E32, E34, E39

T#:371825

Part#: 22316771221

Ships in 1 Business Day

$ 23.99 USD

Add to Wish List

Qty

$ 23.99 USD

Add to Wish List

Stop driveline vibration

U-Joint - E28 E30

We Price Match - Give Us A Call or Chat!

T#:367325

Part#: 26111105398MY

In Stock

$ 30.98

This product was last offered at the strikethrough price on
03-31-2026

$ 24.99 USD

Add to Wish List

Qty

$ 24.99 USD

Add to Wish List

Part Number: 26111105398

This U-Joint fits on the front and rear of your driveshaft - a worn U-Joint can cause problems with your drivetrain. Prevent further drivetrain damage by replacing your U-Joints.

Show More Show Less

Meyle Universal Flex Disc - E21

We Price Match - Give Us A Call or Chat!

T#:7656

Part#: 26111106113

Ships in 3 Business Days

$ 50.22

This product was last offered at the strikethrough price on
07-07-2026

$ 48.82 USD

Add to Wish List

Qty

$ 48.82 USD

Add to Wish List

BMW DRIVESHAFT UNIVERSAL JOINT 26111106113.--

This item fits the following BMWs:
BMW 1600, 2002, 2002tii
BMW 3 Series - 320i, 323i

--.

Transmission Mount - Priced Each

T#:593698

Part#: 22316771130

In Stock at Vendor

$ 64.04

This product was last offered at the strikethrough price on
04-06-2026

$ 21.58 USD

Add to Wish List

Qty

$ 21.58 USD

Add to Wish List

With bad transmission mounts, excessive vibration and noise is transferred to the cabin. The rubber in the mounts wear out over time and cause too much movement in the drivetrain. Replace them when wear is detected to keep everything tight.

Show More Show Less

E24 633/635CSi/M6, E28 535i/M5 JB Racing Lightweight Aluminum Flywhee...

T#:3770

Part#: 520-080-240

Ships in 8 Business Days

$ 630.00 USD

Add to Wish List

Qty

$ 630.00 USD

Add to Wish List

Aluminum flywheels are much lighter than the stock steel flywheel and that produces better throttle response and more available horsepower to the wheels for faster acceleration. The JB Racing aluminum flywheels are a direct replacement for the stock flywheel and work with stock clutch components for an easy upgrade with very little downside.

Modern flywheels are built with additional components and features that are designed to dampen and minimize vibrations from the engine and transmission. As a result they have become bloated in weight and that means more energy is used up just making the flywheel spin. The weight difference between an aluminum and steel flywheel is huge - sometimes more than 50% less. Without the additional mass, more energy can be diverted to where it counts most - moving the car. The flywheel and clutch is one of the first areas that engine builders address when making the rotating assembly lighter for race engines. The dampening effect is just not needed on cars that are focused on performance.

In addition to releasing more power to the wheels, the lighter flywheel allows the engine to spin more freely, which improves throttle response. Again, the difference is huge as you watch the revs build faster than before. With the engine spinning easier the power band comes up much sooner. The stock steel flywheel feels lazy in comparison. There is a driving adjustment required to get used to how much faster the engine revs but that's not really a downside.

The JB lightweight flywheel is designed to be used with a factory organic clutch - the same clutch kit that you would get from any BMW dealer. This makes replacement clutch components easy to source and inexpensive when compared to specialized racing clutches. By using the factory BMW clutch, JB has also made the whole assembly easy to live with when used on the street. The clutch behaves the same as it originally did - just with better throttle response and more power! The JB flywheel can also be rebuilt with a new clutch contact surface - you don't have to buy a new flywheel.

Aluminum flywheels are considered 'single-mass' flywheels because they do not have the same dampening designs as an original 'dual-mass' flywheel. With a single-mass design more noise and vibration may be noticeable. There are steps you can take to minimize the noise - heavier weight transmission oil and clutch discs with anti-rattle springs (sprung-hub clutch).

Stock Flywheel Weight = 22.0lbs
JB Flywheel Weight = 8.5lbs

This flywheel includes the ignition trigger wheel.

This item fits the following BMWs:
1982-1987 E23 BMW 733i 735i
1982-1989 E24 BMW 633csi 635csi M6
1985-1988 E28 BMW 535i 535is M5

Show More Show Less