BMW Drivetrain Parts

OEM ZF Automatic Transmission Service Kit - BMW 8HP F & G-Chassis ...

2X Entries For Our G87 M2 Sweepstakes! "For 8HP45Z, 8HP50Z, 8HP70Z, or 8HP75Z automatic transmissions"

T#:31191923

Part#: ZF8HPATSKT

In Stock

$ 287.99

This product was last offered at the strikethrough price on
04-03-2026

$ 256.99 USD

Add to Wish List

Qty

$ 256.99 USD

Add to Wish List

Over the life of a vehicle, the transmission can often be overlooked when performing routine maintenance. If left unserviced, the automatic transmission fluid will break down, causing the valve body and filter to become contaminated with deposits and sludge. This will lead to poor shifting, slipping, and ultimately, transmission failure. Kit Includes: OEM ZF Automatic transmission filter OEM ZF Oil Pan Gasket & Installation Hardware OEM ZF Drain plug with sealing washer OEM ZF Fill plug with sealing washer 7 Liters of ZF Lifeguard 8 Fluid NOTE: Depending on the model, an additional liter of fluid may be necessary if you are draining your oil cooler or removing the valve body. As per ZF's recommendations, Turner Motorspot suggests performing a full service on your 8HP automatic transmission every 50,000 miles. If your vehicle is modified and makes more power than stock or if your vehicle is regularly track-driven, we recommend shorter 30,000-mile service intervals. This will ensure your transmission's fluid is free from contamination which will help extend the life of internal transmission components like clutch packs and solenoids.

Show More Show Less

Revshift Polurethane Transmission Mount Set - 95A (Track - Green) - E...

T#:600155

Part#: PTM-BT

In Stock

$ 59.99 USD

Add to Wish List

Qty

$ 59.99 USD

Add to Wish List

95A Track (Green): Significantly stiffer and stronger than OEM rubber. Noticeable increase in NVH. Excellent for enthusiastically driven street and track cars.

ZF Automatic Transmission Oil Pan With Transmission Filter - F22 F30 ...

2X Entries For Our G87 M2 Sweepstakes! For 8HP45Z, 8HP50Z, 8HP70Z, or 8HP75Z automatic transmissions

T#:403431

Part#: 24118612901

In Stock

$ 130.99

This product was last offered at the strikethrough price on
04-12-2026

$ 123.99 USD

Add to Wish List

Qty

$ 123.99 USD

Add to Wish List

GA8HP 8 speed automatic transmission. Automatic transmissions are reliable, shift smoothly, and can last without issue so long as they are properly maintained. Over time, the transmission fluid becomes thick and the filter becomes contaminated with small metal particles. This can cause excess wear, high transmission operating temperatures, and eventual failure. To prevent this we recommend changing your filter, fluid, and seals to ensure your transmission continues to operate flawlessly. We recommend filter and fluid changes every 50,000 miles. This item fits the following BMWs: E71,E89 Z4,F06,F10,F12,F13,F15,F16,F22,F25 X3,F26 X4,F30,F31,F32,F33,F34,F36

Show More Show Less

Revshift Polyurethane Motor Mounts - 95A - BMW E36 E46 E9X

T#:1120843

Part#: PMM-R36

Ships on Sep 3, 2026

$ 149.99 USD

Add to Wish List

Qty

$ 149.99 USD

Add to Wish List

These mounts are designed for the BMW E36 and E46 including the M3, Z3, and Z4 as well as the E90/E92 M3. Excluding the E46 XI. Revshift polyurethane motor mounts are made in the U.S.A. from high-grade polyurethane. Revshift mounts are the most durable and reliable mounts on the market. CNC machined billet aluminum flanged ends are embedded deep in the urethane which prevents the isolated ends from separating under extreme loads. Utilizing class 14.9 alloy steel removable screws these mounts will hold your engine in place for a lifetime. To further ensure the strength of these mounts we form the threads with a forming tap which creates denser and stronger threads in the billet aluminum end pieces. These mounts have removable screws for ease of installation. We recommend using Loctite on the threads during installation. Revshift Performance Engineering is a high-performance parts manufacturer with a focus on quality, reliability, and performance. Utilizing high-precision machining technologies and their very own Polyurethane Manufacturing Department, every Revshift product is designed, manufactured, and tested in-house at their Detroit, Michigan facility.

Show More Show Less

ZF 320 5-sp Manual Transmission Shaft Seal Set

2X Entries For Our G87 M2 Sweepstakes!

T#:16707419

Part#: ZFS5D320SEALKIT

In Stock

$ 59.99 USD

Add to Wish List

Qty

$ 59.99 USD

Add to Wish List

OEM ZF Automatic Transmission Filter Kit - GA6HP19Z - E82 E90 E92 E93...

2X Entries For Our G87 M2 Sweepstakes!

T#:596310

Part#: 24152333907

In Stock

$ 121.99 USD

Add to Wish List

Qty

$ 121.99 USD

Add to Wish List

For GA6HP19Z Automatic Transmissions

Automatic transmissions are reliable, shift smoothly, and can last without issue so long as they are properly maintained. Over time, the transmission fluid becomes thick and the filter becomes contaminated with small metal particles. This can cause excess wear, high transmission operating temperatures, and eventual failure. To prevent this we recommend changing your filter, fluid, and seals to ensure your transmission continues to operate flawlessly. We recommend filter and fluid changes every 50,000 miles.

NOTE: This filter fits GA6HP19Z automatic transmissions. This will NOT fit the GA6L45R transmission. Please check your transmission to ensure it is the correct type.

This kit contains:

(1) Oil Pan with Filter

(1) Oil Pan Gasket

(1) Filter O-Ring

(1) Drain Plug

Show More Show Less

Revshift Polurethane Transmission Mount Set - 80A (Street - Black) - ...

T#:47885235

Part#: PTM-BT-80A

Back Ordered

$ 59.99 USD

Add to Wish List

Qty

$ 59.99 USD

Add to Wish List

80A Street (Black) Bushings: Stiffer and stronger than OEM rubber. Minimal increase in NVH. Great choice as an upgrade over stock mounts (OEM+).

BMW E9X M3/E6X M5/M6 Polyurethane Transmission Mounts

T#:1105943

Part#: PTM-E9XM395A

Back Ordered

$ 119.99 USD

Add to Wish List

Qty

$ 119.99 USD

Add to Wish List

BMW E9X M3/E6X M5/M6 Polyurethane Transmission Mounts offer superior performance for both street and track use with their 95A durometer rating. These mounts are engineered by Revshift to provide maximum durability and reliability.

High-Performance Material: Made from high-grade polyurethane in the U.S.A., ensuring longevity and resilience.
Durable Construction: CNC machined 6061-T6 billet aluminum flanged ends are embedded deep into the polyurethane to prevent separation under extreme loads.
Easy Installation: Features removable class 14.9 threaded studs with a hex wrench for simple and convenient installation.
Versatile Use: Ideal for street driving and track applications, combining performance with comfort.
Precision Engineering: Manufactured and tested in-house at Revshift’s Detroit facility, utilizing advanced machining technologies and quality control processes.

Revshift Performance Engineering is renowned for its commitment to quality and performance, making these transmission mounts a reliable choice for enhancing vehicle handling.

Show More Show Less

Revshift Polyurethane Rear Differential Bushing Set - Street - 80A Du...

T#:27405455

Part#: PDB-F8X-80A

Ships in 2 Business Days

$ 249.99 USD

Add to Wish List

Qty

$ 249.99 USD

Add to Wish List

Upgrade your vehicle's rear differential with the Revshift Polyurethane Rear Differential Bushing Set, delivering superior performance and stability. Engineered with precision and premium materials, this set is perfect for street applications, offering enhanced handling and reduced drivetrain movement without compromising on noise, vibration, or harshness levels. This kit is ideal for any enthusiast looking to improve vehicle dynamics without sacrificing overall comfort.

Key Features:

Easy Installation: Two-piece design enables straightforward installation using the included Revshift bushing lube, making upgrading hassle-free. Street Performance: Designed for street use, striking a balance between comfort and performance for everyday driving. Enhanced Stability: Minimize rear differential movement for improved stability and traction during acceleration, cornering, and braking. Durable Polyurethane Construction: Crafted from high-quality polyurethane, ensuring durability and long-lasting performance under daily driving conditions. Reduced Noise and Vibration: Soft and pliable 80A durometer construction significantly reduces NVH compared to higher-durometer or solid alternatives. Upgrade your vehicle's rear differential with the Revshift Polyurethane Rear Differential Bushing Set to experience a noticeable improvement in handling, stability, and overall driving dynamics. Elevate your street performance with confidence and precision.

Show More Show Less

Front Differential Bushing - Priced Each

We Price Match - Give Us A Call or Chat!

T#:362591

Part#: 33171090389

In Stock

$ 28.99

This product was last offered at the strikethrough price on
05-07-2026

$ 23.99 USD

Add to Wish List

Qty

$ 23.99 USD

Add to Wish List

Meyle Front Wheel Hub/Bearing Assembly - E30

We Price Match - Give Us A Call or Chat!

T#:370509

Part#: 31211131297

In Stock

$ 86.99 USD

Add to Wish List

Qty

$ 86.99 USD

Add to Wish List

Includes wheel bearing

Revshift Dual Mount Differential Bushing Kit - 80A (Street - Black) -...

T#:23449724

Part#: DBK-F8X-80ABL

Ships on Sep 4, 2026

$ 599.99 USD

Add to Wish List

Qty

$ 599.99 USD

Add to Wish List

Revshift polyurethane differential bushings completely replace the OEM rubber bushings on the BMW F8X M4 / M3 / M2. This kit includes a second rear bushing and a dual mount bracket that adds a mounting point to the subframe. These bushings securely mount the differential, eliminating wheel hop and improving the vehicle's handling capabilities. The two-piece bushing design sandwiches the subframe, locking everything in place. The bushings will not shift while driving, as other one-piece designs allow. The dual mount bracket was carefully designed for strength and a precise fit. This kit is entirely made at Revshift in the USA from our proprietary polyurethane formula and CNC-machined 6061-T6 billet aluminum.

Show More Show Less

Engine Mount - Priced Each

T#:594933

Part#: 11811132323

Ships in 1-2 days

$ 43.56

This product was last offered at the strikethrough price on
06-01-2026

$ 25.99 USD

Add to Wish List

Qty

$ 25.99 USD

Add to Wish List

Excessive driveline vibration is caused by one of a few things, but more than likely, it is the mounts in your vehicle. They keep your engine and transmission secure for more positive shifting and driveline triangulation as well as absorbing vibration. If any of these are occuring in your BMW, it's time to examine your mounts.

Show More Show Less

Corteco Engine Mount - Left - E38, E39

T#:362312

Part#: 22111092895

In Stock

$ 120.82

This product was last offered at the strikethrough price on
05-13-2026

$ 81.99 USD

Add to Wish List

Qty

$ 81.99 USD

Add to Wish List

Secures engine to subframe for a vibration-free connection

E36 M3, MZ3 JB Racing Lightweight Aluminum Flywheel

T#:3771

Part#: 520-010-240

Ships in 9 Business Days

$ 602.00 USD

Add to Wish List

Qty

$ 602.00 USD

Add to Wish List

Aluminum flywheels are much lighter than the stock steel flywheel and that produces better throttle response and more available horsepower to the wheels for faster acceleration. The JB Racing aluminum flywheels are a direct replacement for the stock flywheel and work with stock clutch components for an easy upgrade with very little downside.

Modern flywheels are built with additional components and features that are designed to dampen and minimize vibrations from the engine and transmission. As a result they have become bloated in weight and that means more energy is used up just making the flywheel spin. The weight difference between an aluminum and steel flywheel is huge - sometimes more than 50% less. Without the additional mass, more energy can be diverted to where it counts most - moving the car. The flywheel and clutch is one of the first areas that engine builders address when making the rotating assembly lighter for race engines. The dampening effect is just not needed on cars that are focused on performance.

In addition to releasing more power to the wheels, the lighter flywheel allows the engine to spin more freely, which improves throttle response. Again, the difference is huge as you watch the revs build faster than before. With the engine spinning easier the power band comes up much sooner. The stock steel flywheel feels lazy in comparison. There is a driving adjustment required to get used to how much faster the engine revs but that's not really a downside.

The JB lightweight flywheel is designed to be used with a factory organic clutch - the same clutch kit that you would get from any BMW dealer. This makes replacement clutch components easy to source and inexpensive when compared to specialized racing clutches. By using the factory BMW clutch, JB has also made the whole assembly easy to live with when used on the street. The clutch behaves the same as it originally did - just with better throttle response and more power! The JB flywheel can also be rebuilt with a new clutch contact surface - you don't have to buy a new flywheel.

Aluminum flywheels are considered 'single-mass' flywheels because they do not have the same dampening designs as an original 'dual-mass' flywheel. With a single-mass design more noise and vibration may be noticeable. There are steps you can take to minimize the noise - heavier weight transmission oil and clutch discs with anti-rattle springs (sprung-hub clutch). In addition to the standard replacement clutches, we also sell Sachs Performance sprung hub clutches that also work with the JB flywheels.

Stock Flywheel Weight = 25.5lbs
JB Flywheel Weight = 10.0lbs

This item fits the following BMWs:
1995-1999 E36 BMW M3
1998-2002 Z3 BMW Z3 M Roadster M Coupe

Show More Show Less

Corteco Engine Mount - Right - E38, E39

T#:362315

Part#: 22111092896

In Stock

$ 153.05

This product was last offered at the strikethrough price on
06-18-2026

$ 149.99 USD

Add to Wish List

Qty

$ 149.99 USD

Add to Wish List

Secures engine to subframe for a vibration-free connection

Meyle Rear Differential Mount - E24, E28

We Price Match - Give Us A Call or Chat!

T#:392737

Part#: 33171129784

In Stock

$ 61.99 USD

Add to Wish List

Qty

$ 61.99 USD

Add to Wish List

Replace damaged bushings to restore handling and performance to your vehicle

Automatic Transmission Service Kit - Lifeguard 6 Fluid

2X Entries For Our G87 M2 Sweepstakes!

T#:13332225

Part#: 24152333907KT

In Stock

$ 302.99

This product was last offered at the strikethrough price on
03-31-2026

$ 259.99 USD

Add to Wish List

Qty

$ 259.99 USD

Add to Wish List

Everything you need for a complete, hassle free transmission service straight from ZF.

ZF Transmission Sealing Sleeve

2X Entries For Our G87 M2 Sweepstakes!

T#:376243

Part#: 24347588725

In Stock

$ 32.27 USD

Add to Wish List

Qty

$ 32.27 USD

Add to Wish List

Connects Mechatronik control assembly to transmission

Revshift Dual Mount Differential Bushing Kit - 95A (Track - Green) - ...

T#:13957880

Part#: DBK-F8X

Ships in 6 Business Days

$ 599.99 USD

Add to Wish List

Qty

$ 599.99 USD

Add to Wish List

Revshift polyurethane differential bushings completely replace the OEM rubber bushings on the BMW F8X M4 / M3 / M2. This kit includes a second rear bushing and a dual mount bracket that adds a mounting point to the subframe. These bushings securely mount the differential, eliminating wheel hop and improving the vehicle's handling capabilities. The two-piece bushing design sandwiches the subframe, locking everything in place. The bushings will not shift while driving, as other one-piece designs allow. The dual mount bracket was carefully designed for strength and a precise fit. This kit is entirely made at Revshift in the USA from our proprietary polyurethane formula and CNC-machined 6061-T6 billet aluminum.

Show More Show Less

RevShift Differential Bushing Set - BMW E9X / E8X - 80A Street ...

For Non-M Models Only

T#:39363088

Part#: DBS-E9X80A-REV

Ships in 2 Business Days

$ 129.99 USD

Add to Wish List

Qty

$ 129.99 USD

Add to Wish List

Differential Bushing Set - BMW E9X / E8X (Non-M) Enhance your driveline performance with this premium differential bushing set, designed specifically for E9X and E8X Non-M models. Factory rubber bushings degrade over time, leading to excessive drivetrain movement, clunking, and inefficient power transfer. These high-quality replacement bushings provide firm, reliable differential support, minimizing deflection for sharper throttle response and improved drivetrain stability. Whether you're replacing worn-out components or upgrading for spirited driving, this set delivers a more connected and controlled feel on the road. Precision-engineered for a direct OE-style fit, these bushings install seamlessly without modifications. Restore crisp, precise performance to your BMW today! ✅ Direct-fit replacement for aging factory bushings ✅ Reduces drivetrain flex and enhances power delivery ✅ Perfect for daily drivers and performance applications 📦 Includes: Full set of differential bushings for a complete refresh.

Show More Show Less

E30 318i/is, E36 318i, Z3 1.9 JB Racing Lightweight Aluminum Flywheel...

T#:3769

Part#: 520-040-215

Back Ordered

11% off MSRP $ 765.00

MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.

$ 679.00 USD

Add to Wish List

Qty

11% off MSRP

$ 765.00

MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.

$ 679.00 USD

Add to Wish List

Aluminum flywheels are much lighter than the stock steel flywheel and that produces better throttle response and more available horsepower to the wheels for faster acceleration. The JB Racing aluminum flywheels are a direct replacement for the stock flywheel and work with stock clutch components for an easy upgrade with very little downside.

Modern flywheels are built with additional components and features that are designed to dampen and minimize vibrations from the engine and transmission. As a result they have become bloated in weight and that means more energy is used up just making the flywheel spin. The weight difference between an aluminum and steel flywheel is huge - sometimes more than 50% less. Without the additional mass, more energy can be diverted to where it counts most - moving the car. The flywheel and clutch is one of the first areas that engine builders address when making the rotating assembly lighter for race engines. The dampening effect is just not needed on cars that are focused on performance.

In addition to releasing more power to the wheels, the lighter flywheel allows the engine to spin more freely, which improves throttle response. Again, the difference is huge as you watch the revs build faster than before. With the engine spinning easier the power band comes up much sooner. The stock steel flywheel feels lazy in comparison. There is a driving adjustment required to get used to how much faster the engine revs but that's not really a downside.

The JB lightweight flywheel is designed to be used with a factory organic clutch - the same clutch kit that you would get from any BMW dealer. This makes replacement clutch components easy to source and inexpensive when compared to specialized racing clutches. By using the factory BMW clutch, JB has also made the whole assembly easy to live with when used on the street. The clutch behaves the same as it originally did - just with better throttle response and more power! The JB flywheel can also be rebuilt with a new clutch contact surface - you don't have to buy a new flywheel.

Aluminum flywheels are considered 'single-mass' flywheels because they do not have the same dampening designs as an original 'dual-mass' flywheel. With a single-mass design more noise and vibration may be noticeable. There are steps you can take to minimize the noise - heavier weight transmission oil and clutch discs with anti-rattle springs (sprung-hub clutch).

Stock Flywheel Weight = 27.0lbs
JB Flywheel Weight = 9.0lbs

This item fits the following BMWs:
1989-1992 E30 BMW 318i 318is 318ic
1992-1997 E36 BMW 318i 318is 318ti 318ic
1996-1997 Z3 BMW Z3 1.9

Show More Show Less

Revshift Polyurethane Differential Bushings - Street / Black (80A) - ...

T#:41728752

Part#: PDB-E46M-80A

Ships in 4 Business Days

$ 109.99 USD

Add to Wish List

Qty

$ 109.99 USD

Add to Wish List

Revshift polyurethane differential bushings completely replace the OEM rubber bushings on the E46 M3 and Z4M. These bushings stiffen the differential, improving the vehicle's handling capabilities and eliminating drive-line slop.

Show More Show Less

Revshift Polyurethane Differential Bushings - Track / Green (95A) - E...

T#:582011

Part#: PDBE46MGREEN

Ships in 2 Business Days

$ 109.99 USD

Add to Wish List

Qty

$ 109.99 USD

Add to Wish List

Revshift polyurethane differential bushings completely replace the OEM rubber bushings on the E46 M3 and Z4M. These bushings stiffen the differential, improving the vehicle's handling capabilities and eliminating drive-line slop.

Show More Show Less

Sealing Sleeve

2X Entries For Our G87 M2 Sweepstakes!

T#:594175

Part#: 24107536340

In Stock

$ 24.39 USD

Add to Wish List

Qty

$ 24.39 USD

Add to Wish List

Found in the transmission housing

E60, E82, E85, E9X, E89 (N52 Engine) JB Racing Lightweight Aluminum F...

T#:2801

Part#: 520-200-240

In Stock

$ 714.00 USD

Add to Wish List

Qty

$ 714.00 USD

Add to Wish List

Aluminum flywheels are much lighter than the stock steel flywheel and that produces better throttle response and more available horsepower to the wheels for faster acceleration. The JB Racing aluminum flywheels are a direct replacement for the stock flywheel and work with stock clutch components for an easy upgrade with very little downside.

Modern flywheels are built with additional components and features that are designed to dampen and minimize vibrations from the engine and transmission. As a result they have become bloated in weight and that means more energy is used up just making the flywheel spin. The weight difference between an aluminum and steel flywheel is huge - sometimes more than 50% less. Without the additional mass, more energy can be diverted to where it counts most - moving the car. The flywheel and clutch is one of the first areas that engine builders address when making the rotating assembly lighter for race engines. The dampening effect is just not needed on cars that are focused on performance.

In addition to releasing more power to the wheels, the lighter flywheel allows the engine to spin more freely, which improves throttle response. Again, the difference is huge as you watch the revs build faster than before. With the engine spinning easier the power band comes up much sooner. The stock steel flywheel feels lazy in comparison. There is a driving adjustment required to get used to how much faster the engine revs but that's not really a downside.

The JB lightweight flywheel is designed to be used with a factory organic clutch - the same clutch kit that you would get from any BMW dealer. This makes replacement clutch components easy to source and inexpensive when compared to specialized racing clutches. By using the factory BMW clutch, JB has also made the whole assembly easy to live with when used on the street. The clutch behaves the same as it originally did - just with better throttle response and more power! The JB flywheel can also be rebuilt with a new clutch contact surface - you don't have to buy a new flywheel.

Aluminum flywheels are considered 'single-mass' flywheels because they do not have the same dampening designs as an original 'dual-mass' flywheel. With a single-mass design more noise and vibration may be noticeable. There are steps you can take to minimize the noise - heavier weight transmission oil and clutch discs with anti-rattle springs (sprung-hub clutch).

This JB flywheel replaces the stock flywheel and can be used with either the stock 228mm or stock 240mm clutch discs. Depending on the model you may have either clutch size in your car but this flywheel is compatible with both. You can install a 240mm clutch as a mild upgrade.

Stock Flywheel Weight = 24-31.0lbs
JB Flywheel Weight = 12.0lbs

This item fits the following BMWs:
2006-2010 E60 BMW - 525i, 528i, 530i
2006-2013 E90, E91, E92, E93 BMW - 325i, 328i, 330i
2007-2013 E82 BMW - 125i, 128i
2006-2008 E85, E86 BMW - Z4 3.0i, Z4 3.0si
2009-later E89 BMW - Z4 3.0i

Show More Show Less

E46 M3 6MT JB Racing Lightweight Aluminum Flywheel

T#:302739

Part#: 520-180-240

Ships in 8 Business Days

$ 602.00 USD

Add to Wish List

Qty

$ 602.00 USD

Add to Wish List

Aluminum flywheels are much lighter than the stock steel flywheel and that produces better throttle response and more available horsepower to the wheels for faster acceleration. The JB Racing aluminum flywheels are a direct replacement for the stock flywheel and work with stock clutch components for an easy upgrade with very little downside.

Modern flywheels are built with additional components and features that are designed to dampen and minimize vibrations from the engine and transmission. As a result they have become bloated in weight and that means more energy is used up just making the flywheel spin. The weight difference between an aluminum and steel flywheel is huge - sometimes more than 50% less. Without the additional mass, more energy can be diverted to where it counts most - moving the car. The flywheel and clutch is one of the first areas that engine builders address when making the rotating assembly lighter for race engines. The dampening effect is just not needed on cars that are focused on performance.

In addition to releasing more power to the wheels, the lighter flywheel allows the engine to spin more freely, which improves throttle response. Again, the difference is huge as you watch the revs build faster than before. With the engine spinning easier the power band comes up much sooner. The stock steel flywheel feels lazy in comparison. There is a driving adjustment required to get used to how much faster the engine revs but that's not really a downside.

The JB lightweight flywheel is designed to be used with a factory organic clutch - the same clutch kit that you would get from any BMW dealer. This makes replacement clutch components easy to source and inexpensive when compared to specialized racing clutches. By using the factory BMW clutch, JB has also made the whole assembly easy to live with when used on the street. The clutch behaves the same as it originally did - just with better throttle response and more power! The JB flywheel can also be rebuilt with a new clutch contact surface - you don't have to buy a new flywheel.

Aluminum flywheels are considered 'single-mass' flywheels because they do not have the same dampening designs as an original 'dual-mass' flywheel. With a single-mass design more noise and vibration may be noticeable. There are steps you can take to minimize the noise - heavier weight transmission oil and clutch discs with anti-rattle springs (sprung-hub clutch). In addition to the standard replacement clutches, we also sell Sachs Performance sprung hub clutches that also work with the JB flywheels.

Stock Flywheel Weight = 25.0lbs
JB Flywheel Weight = 10.0lbs

This item fits the following BMWs:
2001-2006 E46 BMW M3 (6-speed manual only, not for SMG)

Show More Show Less

OEM ZF Automatic Transmission Filter Kit - GA8HP75 GAHP76 - BMW F85/8...

2X Entries For Our G87 M2 Sweepstakes!

T#:31125616

Part#: 24007855263

Back Ordered

$ 149.99 USD

Add to Wish List

Qty

$ 149.99 USD

Add to Wish List

This is a brand new automatic transmission filter service kit directly from ZF for the GAHP75 and GAHP76 transmissions found in many of the newer BMW M cars, including the G8X M2, M3, & M4, F90 M5, F91/92/93 M8, F97 X3M, F98 X4M, F85 X5M, and F86 X6M. This kit includes all of the basic components needed to service your transmission, other than the transmission fluid. Included: Oil Pan Gasket Oil Filter Drain & Fill Plugs Oil Pan Mounting Screws (Qty 13) As per ZF's recommendations, we suggest replacing your filter and changing your fluid every 50,000 miles. If your vehicle is modified and makes more power than stock, or if your vehicle is regularly track-driven, we recommend shorter 30,000-mile service intervals. This will ensure your transmission's fluid is free from contamination which will help extend the life of internal transmission components like clutch packs and solenoids.

Show More Show Less

E46 323/325/328/330 5-speed, Z3 2.3/2.8/3.0 JB Racing Lightweight Alu...

T#:4227

Part#: 520-140-240

In Stock

$ 602.00 USD

Add to Wish List

Qty

$ 602.00 USD

Add to Wish List

Aluminum flywheels are much lighter than the stock steel flywheel and that produces better throttle response and more available horsepower to the wheels for faster acceleration. The JB Racing aluminum flywheels are a direct replacement for the stock flywheel and work with stock clutch components for an easy upgrade with very little downside.

Modern flywheels are built with additional components and features that are designed to dampen and minimize vibrations from the engine and transmission. As a result they have become bloated in weight and that means more energy is used up just making the flywheel spin. The weight difference between an aluminum and steel flywheel is huge - sometimes more than 50% less. Without the additional mass, more energy can be diverted to where it counts most - moving the car. The flywheel and clutch is one of the first areas that engine builders address when making the rotating assembly lighter for race engines. The dampening effect is just not needed on cars that are focused on performance.

In addition to releasing more power to the wheels, the lighter flywheel allows the engine to spin more freely, which improves throttle response. Again, the difference is huge as you watch the revs build faster than before. With the engine spinning easier the power band comes up much sooner. The stock steel flywheel feels lazy in comparison. There is a driving adjustment required to get used to how much faster the engine revs but that's not really a downside.

The JB lightweight flywheel is designed to be used with a factory organic clutch - the same clutch kit that you would get from any BMW dealer. This makes replacement clutch components easy to source and inexpensive when compared to specialized racing clutches. By using the factory BMW clutch, JB has also made the whole assembly easy to live with when used on the street. The clutch behaves the same as it originally did - just with better throttle response and more power! The JB flywheel can also be rebuilt with a new clutch contact surface - you don't have to buy a new flywheel.

Aluminum flywheels are considered 'single-mass' flywheels because they do not have the same dampening designs as an original 'dual-mass' flywheel. With a single-mass design more noise and vibration may be noticeable. There are steps you can take to minimize the noise - heavier weight transmission oil and clutch discs with anti-rattle springs (sprung-hub clutch). In addition to the standard replacement clutches, we also sell Sachs Performance sprung hub clutches that also work with the JB flywheels.

Stock Flywheel Weight = 25.0lbs
JB Flywheel Weight = 10.0lbs

This item fits the following BMWs:
1999-2002 E46 BMW 323i 323ci 325i 325ci 328i 328ci 330i 330ci (with 5-speed manual transmission)
2001-2005 E46 BMW 325xi 330xi
1997-2002 Z3 BMW Z3 2.3 Z3 2.5i Z3 2.8 Z3 3.0i

Show More Show Less

JB Racing Single Mass Lightweight Aluminum Flywheel - 6-speed - E46 3...

T#:3474

Part#: 520-190-240

Ships in 4 Business Days

$ 672.00 USD

Add to Wish List

Qty

$ 672.00 USD

Add to Wish List

This is a performance replacement for BMW Part # 21207533868 Aluminum flywheels are much lighter than the stock steel flywheel and that produces better throttle response and more available horsepower to the wheels for faster acceleration. The JB Racing aluminum flywheels are a direct replacement for the stock flywheel and work with stock clutch components for an easy upgrade with very little downside.

Modern flywheels are built with additional components and features that are designed to dampen and minimize vibrations from the engine and transmission. As a result they have become bloated in weight and that means more energy is used up just making the flywheel spin. The weight difference between an aluminum and steel flywheel is huge - sometimes more than 50% less. Without the additional mass, more energy can be diverted to where it counts most - moving the car. The flywheel and clutch is one of the first areas that engine builders address when making the rotating assembly lighter for race engines. The dampening effect is just not needed on cars that are focused on performance.

In addition to releasing more power to the wheels, the lighter flywheel allows the engine to spin more freely, which improves throttle response. Again, the difference is huge as you watch the revs build faster than before. With the engine spinning easier the power band comes up much sooner. The stock steel flywheel feels lazy in comparison. There is a driving adjustment required to get used to how much faster the engine revs but that's not really a downside.

The JB lightweight flywheel is designed to be used with a factory organic clutch - the same clutch kit that you would get from any BMW dealer. This makes replacement clutch components easy to source and inexpensive when compared to specialized racing clutches. By using the factory BMW clutch, JB has also made the whole assembly easy to live with when used on the street. The clutch behaves the same as it originally did - just with better throttle response and more power! The JB flywheel can also be rebuilt with a new clutch contact surface - you don't have to buy a new flywheel.

Aluminum flywheels are considered 'single-mass' flywheels because they do not have the same dampening designs as an original 'dual-mass' flywheel. With a single-mass design more noise and vibration may be noticeable. There are steps you can take to minimize the noise - heavier weight transmission oil and clutch discs with anti-rattle springs (sprung-hub clutch).

The JB Flywheel includes the pilot bearing mounted in the flywheel hub, just like the factory configuration.

Stock Flywheel Weight = 25.0lbs
JB Flywheel Weight = 10.5lbs

This item fits the following BMWs:
2002-2005 E46 BMW 325i 330i (with 6-speed manual transmission)

Show More Show Less

Rear Differential Mount - Front Position

We Price Match - Give Us A Call or Chat!

T#:594515

Part#: 33316792873

Ships in 2 Business Days

$ 41.99

This product was last offered at the strikethrough price on
05-07-2026

$ 40.99 USD

Add to Wish List

Qty

$ 40.99 USD

Add to Wish List

Over time bushings deteriorate and become ineffective. Replace them to reduce noise and harshness. Priced Each. Two required for complete service.

E9X M3 Polyurethane Transmission Mounts 80A Black - Street

T#:46959255

Part#: 37791428772017

Ships in 5 Business Days

$ 119.99 USD

Add to Wish List

Qty

$ 119.99 USD

Add to Wish List

Differential Input Shaft Seal - Priced Each

T#:44021076

Part#: 33121213949

Ships in 2 Business Days

$ 27.99

This product was last offered at the strikethrough price on
05-07-2026

$ 26.99 USD

Add to Wish List

Qty

$ 26.99 USD

Add to Wish List

Meyle CV Boot Repair Kit - Inner - E36

We Price Match - Give Us A Call or Chat!

T#:592404

Part#: 33219067819

Ships in 1-2 days

$ 70.43 USD

Add to Wish List

Qty

$ 70.43 USD

Add to Wish List

Replace torn CV boots and save CV joints

E30 325i, E34 525i (M20) JB Racing Lightweight Aluminum Flywheel (Rep...

T#:385699

Part#: 520-060-228

Ships on Sep 1, 2026

$ 581.00 USD

Add to Wish List

Qty

$ 581.00 USD

Add to Wish List

Aluminum flywheels are much lighter than the stock steel flywheel and that produces better throttle response and more available horsepower to the wheels for faster acceleration. The JB Racing aluminum flywheels are a direct replacement for the stock flywheel and work with stock clutch components for an easy upgrade with very little downside.

Modern flywheels are built with additional components and features that are designed to dampen and minimize vibrations from the engine and transmission. As a result they have become bloated in weight and that means more energy is used up just making the flywheel spin. The weight difference between an aluminum and steel flywheel is huge - sometimes more than 50% less. Without the additional mass, more energy can be diverted to where it counts most - moving the car. The flywheel and clutch is one of the first areas that engine builders address when making the rotating assembly lighter for race engines. The dampening effect is just not needed on cars that are focused on performance.

In addition to releasing more power to the wheels, the lighter flywheel allows the engine to spin more freely, which improves throttle response. Again, the difference is huge as you watch the revs build faster than before. With the engine spinning easier the power band comes up much sooner. The stock steel flywheel feels lazy in comparison. There is a driving adjustment required to get used to how much faster the engine revs but that's not really a downside.

The JB lightweight flywheel is designed to be used with a factory organic clutch - the same clutch kit that you would get from any BMW dealer. This makes replacement clutch components easy to source and inexpensive when compared to specialized racing clutches. By using the factory BMW clutch, JB has also made the whole assembly easy to live with when used on the street. The clutch behaves the same as it originally did - just with better throttle response and more power! The JB flywheel can also be rebuilt with a new clutch contact surface - you don't have to buy a new flywheel.

Aluminum flywheels are considered 'single-mass' flywheels because they do not have the same dampening designs as an original 'dual-mass' flywheel. With a single-mass design more noise and vibration may be noticeable. There are steps you can take to minimize the noise - heavier weight transmission oil and clutch discs with anti-rattle springs (sprung-hub clutch).

This flywheel replaces the stock original single-mass flywheel and should only be used with the corresponding 'single-mass' clutch kit. According to BMW the single mass flywheel was installed in all 325i up to 12/86 production date but we have seen some later cars with a single-mass flywheel. The age of the car almost guarantees one or more clutch replacements and possibly a change to the original flywheel as well. You may not know which flywheel is currently installed until the flywheel cover or the transmission is removed.

Stock Flywheel Weight = 18.0lbs
JB Flywheel Weight = 8.0lbs

This item fits the following BMWs:
1984-1991 E30 BMW 325i 325ic 325is (with single-mass flywheel)
1989-1990 E34 BMW 525i (with single-mass flywheel)

Show More Show Less

DCT Transmission Filter & Gasket - GS7D36SG - E82/88 135i, E9X M3 335...

We Price Match - Give Us A Call or Chat!

T#:29234322

Part#: 3001360302

Ships on Oct 29, 2026

$ 57.99 USD

Add to Wish List

Qty

$ 57.99 USD

Add to Wish List

BMW claims their transmission fluid to be a "lifetime" fluid, however is recommended to be changed every 60,000 miles to ensure a longer transmission life. Though not exposed to the same level of heat and contamination as engine oil, transmission oil still breaks down over time due to heat and becomes contaminated as your transmission wears. Old contaminated oil can lead to excessive wear and tear on sensitive transmission components which could lead to slow shifting, slips, and even complete failure. This is also true for the transmission filter. The filter removes metal particles from the transmission fluid and eventually begins to clog, preventing fluid from passing through the filter easily. This leads to excessive wear and a reduced transmission lifespan if not changed. Not sure if this kit is right for your BMW? Contact our sales staff with your VIN to confirm the exact part you need.

Show More Show Less

Meyle Driveshaft Center Support - E36, E39, Z3

We Price Match - Give Us A Call or Chat!

T#:359503

Part#: 26121226731

Back Ordered

$ 34.99 USD

Add to Wish List

Qty

$ 34.99 USD

Add to Wish List

Replacement center support bearing for the driveshaft from Meyle. Often the cause of annoying vibrations and clunking noises during take-offs.

This item fits the following BMWs:
Manual Transmission
1992-1998 E36 BMW 318i 318is 318ic 323is 323ic 325is 325ic 328i 328is 328ic
12/94-1995 E36 BMW 325i Sedan
1997-2003 E39 BMW 525i 530i

Automatic Transmission
1992-1998 E36 BMW 318ti 323is 323ic 328i 328is 328ic
1998-2003 E39 BMW 525i 528i 530i
1999-2002 Z3 BMW Z3 2.5i Z3 3.0i

Show More Show Less

BMW Automatic Transmission Service Kit - Level 2 - Lifeguard 6 ATF ...

2X Entries For Our G87 M2 Sweepstakes! GA6HP26Z Service Kit

T#:13102202

Part#: 24152333903KT4

In Stock

$ 326.99

This product was last offered at the strikethrough price on
03-31-2026

$ 277.99 USD

Add to Wish List

Qty

$ 277.99 USD

Add to Wish List

BMW Automatic Transmission Service Kit - Level 2 - Lifeguard 6 is a comprehensive service solution that includes everything needed to effectively maintain and service your BMW's transmission using high-quality ZF components and fluid. While BMW suggests that the ZF transmission utilizes a lifetime fluid, it’s important to understand that “lifetime” refers to the warranty, not the transmission's operational lifespan. Over time, the fluid degrades, becoming less effective at transferring heat and lubricating internal components. This degradation can lead to premature wear, resulting in louder operation, harder shifts, and potentially severe internal damage.

ZF recommends service intervals of 50,000 miles or 8 years—whichever comes first—for 6HP transmissions. By using OEM ZF components in this kit, BMW owners can ensure that only the highest quality factory parts and fluids are used, keeping the transmission running smoothly for years to come.

Benefits:

Comprehensive Kit: Contains all necessary components for a complete transmission service, ensuring an efficient and thorough maintenance process.
High-Quality OEM Parts: Includes ZF components, guaranteeing compatibility and superior performance.
Prevents Premature Wear: Regular service helps avoid costly repairs by maintaining fluid integrity and component lubrication.
Improves Performance: Enhanced fluid conditions contribute to smoother shifting and quieter operation.
Recommended Service Intervals: Follows ZF’s guidelines for optimal maintenance, promoting longevity in your BMW’s transmission.

Show More Show Less

E34 M5 JB Racing Lightweight Aluminum Flywheel

T#:3772

Part#: 520-090-240

Ships in 7 Business Days

$ 581.00 USD

Add to Wish List

Qty

$ 581.00 USD

Add to Wish List

Aluminum flywheels are much lighter than the stock steel flywheel and that produces better throttle response and more available horsepower to the wheels for faster acceleration. The JB Racing aluminum flywheels are a direct replacement for the stock flywheel and work with stock clutch components for an easy upgrade with very little downside.

Modern flywheels are built with additional components and features that are designed to dampen and minimize vibrations from the engine and transmission. As a result they have become bloated in weight and that means more energy is used up just making the flywheel spin. The weight difference between an aluminum and steel flywheel is huge - sometimes more than 50% less. Without the additional mass, more energy can be diverted to where it counts most - moving the car. The flywheel and clutch is one of the first areas that engine builders address when making the rotating assembly lighter for race engines. The dampening effect is just not needed on cars that are focused on performance.

In addition to releasing more power to the wheels, the lighter flywheel allows the engine to spin more freely, which improves throttle response. Again, the difference is huge as you watch the revs build faster than before. With the engine spinning easier the power band comes up much sooner. The stock steel flywheel feels lazy in comparison. There is a driving adjustment required to get used to how much faster the engine revs but that's not really a downside.

The JB lightweight flywheel is designed to be used with a factory organic clutch - the same clutch kit that you would get from any BMW dealer. This makes replacement clutch components easy to source and inexpensive when compared to specialized racing clutches. By using the factory BMW clutch, JB has also made the whole assembly easy to live with when used on the street. The clutch behaves the same as it originally did - just with better throttle response and more power! The JB flywheel can also be rebuilt with a new clutch contact surface - you don't have to buy a new flywheel.

Aluminum flywheels are considered 'single-mass' flywheels because they do not have the same dampening designs as an original 'dual-mass' flywheel. With a single-mass design more noise and vibration may be noticeable.

Stock Flywheel Weight = 16.0lbs
JB Flywheel Weight = 8.0lbs

This item fits the following BMWs:
1991-1995 E34 BMW M5

Show More Show Less

2002, E21 320i, E30 318i (M10) JB Racing Lightweight Aluminum Flywhee...

T#:3647

Part#: 520-110-215

Ships in 2 Business Days

$ 581.00 USD

Add to Wish List

Qty

$ 581.00 USD

Add to Wish List

Aluminum flywheels are much lighter than the stock steel flywheel and that produces better throttle response and more available horsepower to the wheels for faster acceleration. The JB Racing aluminum flywheels are a direct replacement for the stock flywheel and work with stock clutch components for an easy upgrade with very little downside.

Modern flywheels are built with additional components and features that are designed to dampen and minimize vibrations from the engine and transmission. As a result they have become bloated in weight and that means more energy is used up just making the flywheel spin. The weight difference between an aluminum and steel flywheel is huge - sometimes more than 50% less. Without the additional mass, more energy can be diverted to where it counts most - moving the car. The flywheel and clutch is one of the first areas that engine builders address when making the rotating assembly lighter for race engines. The dampening effect is just not needed on cars that are focused on performance.

In addition to releasing more power to the wheels, the lighter flywheel allows the engine to spin more freely, which improves throttle response. Again, the difference is huge as you watch the revs build faster than before. With the engine spinning easier the power band comes up much sooner. The stock steel flywheel feels lazy in comparison. There is a driving adjustment required to get used to how much faster the engine revs but that's not really a downside.

The JB lightweight flywheel is designed to be used with a factory organic clutch - the same clutch kit that you would get from any BMW dealer. This makes replacement clutch components easy to source and inexpensive when compared to specialized racing clutches. By using the factory BMW clutch, JB has also made the whole assembly easy to live with when used on the street. The clutch behaves the same as it originally did - just with better throttle response and more power! The JB flywheel can be rebuilt too with a new clutch contact surface.

Aluminum flywheels are considered 'single-mass' flywheels because they do not have the same dampening designs as an original 'dual-mass' flywheel. With a single-mass design more noise and vibration may be noticeable. There are steps you can take to minimize the noise - heavier weight transmission oil and clutch discs with anti-rattle springs (sprung-hub clutch).

Stock Flywheel Weight = 16.5lbs
JB Flywheel Weight = 8lbs

This item fits the following BMWs:
1974-1976 2002 BMW 2002
1977-1983 E21 BMW 320i
1984-1985 E30 BMW 318i

Show More Show Less

E30 M3 JB Racing Lightweight Aluminum Flywheel

T#:3768

Part#: 520-050-228

Ships in 4 Business Days

$ 630.00 USD

Add to Wish List

Qty

$ 630.00 USD

Add to Wish List

Aluminum flywheels are much lighter than the stock steel flywheel and that produces better throttle response and more available horsepower to the wheels for faster acceleration. The JB Racing aluminum flywheels are a direct replacement for the stock flywheel and work with stock clutch components for an easy upgrade with very little downside.

Modern flywheels are built with additional components and features that are designed to dampen and minimize vibrations from the engine and transmission. As a result they have become bloated in weight and that means more energy is used up just making the flywheel spin. The weight difference between an aluminum and steel flywheel is huge - sometimes more than 50% less. Without the additional mass, more energy can be diverted to where it counts most - moving the car. The flywheel and clutch is one of the first areas that engine builders address when making the rotating assembly lighter for race engines. The dampening effect is just not needed on cars that are focused on performance.

In addition to releasing more power to the wheels, the lighter flywheel allows the engine to spin more freely, which improves throttle response. Again, the difference is huge as you watch the revs build faster than before. With the engine spinning easier the power band comes up much sooner. The stock steel flywheel feels lazy in comparison. There is a driving adjustment required to get used to how much faster the engine revs but that's not really a downside.

The JB lightweight flywheel is designed to be used with a factory organic clutch - the same clutch kit that you would get from any BMW dealer. This makes replacement clutch components easy to source and inexpensive when compared to specialized racing clutches. By using the factory BMW clutch, JB has also made the whole assembly easy to live with when used on the street. The clutch behaves the same as it originally did - just with better throttle response and more power! The JB flywheel can also be rebuilt with a new clutch contact surface - you don't have to buy a new flywheel.

Aluminum flywheels are considered 'single-mass' flywheels because they do not have the same dampening designs as an original 'dual-mass' flywheel. With a single-mass design more noise and vibration may be noticeable. There are steps you can take to minimize the noise - heavier weight transmission oil and clutch discs with anti-rattle springs (sprung-hub clutch).

The JB flywheel includes ignition trigger wheel.

Stock Flywheel Weight = 19.5lbs
JB Flywheel Weight = 8.0lbs

This item fits the following BMWs:
1987-1991 E30 BMW M3

Show More Show Less

Rear Wheel Bearing

We Price Match - Give Us A Call or Chat!

T#:5282919

Part#: 33416792361

In Stock

$ 53.99

This product was last offered at the strikethrough price on
08-10-2026

$ 44.99 USD

Limited Qty Sale

Add to Wish List

Qty

$ 53.99

This product was last offered at the strikethrough price on
08-10-2026

$ 44.99 USD

Limited Qty Sale

Add to Wish List

The Rear Wheel Bearing facilitates smooth wheel rotation by minimizing friction, ensuring quiet operation. It improves stability, handling, and overall driving performance.

Corteco Output Shaft Seal - E10, E21

T#:592386

Part#: 33121205302

In Stock

$ 28.99 USD

Add to Wish List

Qty

$ 28.99 USD

Add to Wish List

Seals the axles into the differential

Automatic Transmission Oil Pan With Transmission Filter - GA8P75HZ - ...

We Price Match - Give Us A Call or Chat! For vehicles with a ZF GA8P75HZ automatic transmission only

T#:29201103

Part#: 3003250010

In Stock

Sale - Save 40% $ 207.99

This product was last offered at the strikethrough price on
05-03-2026

$ 125.00 USD

Add to Wish List

Qty

Sale - Save 40%

$ 207.99

This product was last offered at the strikethrough price on
05-03-2026

$ 125.00 USD

Add to Wish List

BMW claims their transmission fluid to be a "lifetime" fluid, however is recommended to be changed every 60,000 miles to ensure a longer transmission life. Though not exposed to the same level of heat and contamination as engine oil, transmission oil still breaks down over time due to heat and becomes contaminated as your transmission wears. Old contaminated oil can lead to excessive wear and tear on sensitive transmission components which could lead to slow shifting, slips, and even complete failure. This is also true for the transmission filter integrated into the transmission fluid pan. The filter removes metal particles from the transmission fluid and eventually begins to clog, preventing fluid from passing through the filter easily. This leads to excessive wear and a reduced transmission lifespan if not changed. This high-quality Meyle transmission pan includes a new filter and is quintessential for a correct and full service. Not sure if this kit is right for your BMW? Contact our sales staff with your VIN to confirm the exact part you need.

Show More Show Less

Corteco Transmission Mount - E60

T#:592084

Part#: 22316771741

In Stock

$ 41.99

This product was last offered at the strikethrough price on
04-06-2026

$ 21.99 USD

Add to Wish List

Qty

$ 21.99 USD

Add to Wish List

Replace your worn transmission mounts

E39 540i 97-03 JB Racing Lightweight Aluminum Flywheel

T#:1339

Part#: 520-150-240

In Stock

$ 903.00 USD

Add to Wish List

Qty

$ 903.00 USD

Add to Wish List

Aluminum flywheels are much lighter than the stock steel flywheel and that produces better throttle response and more available horsepower to the wheels for faster acceleration. The JB Racing aluminum flywheels are a direct replacement for the stock flywheel and work with stock clutch components for an easy upgrade with very little downside.

Modern flywheels are built with additional components and features that are designed to dampen and minimize vibrations from the engine and transmission. As a result they have become bloated in weight and that means more energy is used up just making the flywheel spin. The weight difference between an aluminum and steel flywheel is huge - sometimes more than 50% less. Without the additional mass, more energy can be diverted to where it counts most - moving the car. The flywheel and clutch is one of the first areas that engine builders address when making the rotating assembly lighter for race engines. The dampening effect is just not needed on cars that are focused on performance.

In addition to releasing more power to the wheels, the lighter flywheel allows the engine to spin more freely, which improves throttle response. Again, the difference is huge as you watch the revs build faster than before. With the engine spinning easier the power band comes up much sooner. The stock steel flywheel feels lazy in comparison. There is a driving adjustment required to get used to how much faster the engine revs but that's not really a downside.

The JB lightweight flywheel is designed to be used with a factory organic clutch - the same clutch kit that you would get from any BMW dealer. This makes replacement clutch components easy to source and inexpensive when compared to specialized racing clutches. By using the factory BMW clutch, JB has also made the whole assembly easy to live with when used on the street. The clutch behaves the same as it originally did - just with better throttle response and more power! The JB flywheel can also be rebuilt with a new clutch contact surface - you don't have to buy a new flywheel.

Aluminum flywheels are considered 'single-mass' flywheels because they do not have the same dampening designs as an original 'dual-mass' flywheel. With a single-mass design more noise and vibration may be noticeable. There are steps you can take to minimize the noise - heavier weight transmission oil and clutch discs with anti-rattle springs (sprung-hub clutch).

Stock Flywheel Weight = 33.0lbs
JB Flywheel Weight = 13.0lbs

This item fits the following BMWs:
1997-2003 E39 BMW 540i

Show More Show Less

Corteco Transmission Mount - E32, E34, E39

T#:371825

Part#: 22316771221

Ships in 1 Business Day

$ 23.99 USD

Add to Wish List

Qty

$ 23.99 USD

Add to Wish List

Stop driveline vibration

U-Joint - E28 E30

We Price Match - Give Us A Call or Chat!

T#:367325

Part#: 26111105398MY

In Stock

$ 30.98

This product was last offered at the strikethrough price on
03-31-2026

$ 24.99 USD

Add to Wish List

Qty

$ 24.99 USD

Add to Wish List

Part Number: 26111105398

This U-Joint fits on the front and rear of your driveshaft - a worn U-Joint can cause problems with your drivetrain. Prevent further drivetrain damage by replacing your U-Joints.

Show More Show Less

Meyle Universal Flex Disc - E21

We Price Match - Give Us A Call or Chat!

T#:7656

Part#: 26111106113

Ships in 3 Business Days

$ 50.22

This product was last offered at the strikethrough price on
07-07-2026

$ 48.82 USD

Add to Wish List

Qty

$ 48.82 USD

Add to Wish List

BMW DRIVESHAFT UNIVERSAL JOINT 26111106113.--

This item fits the following BMWs:
BMW 1600, 2002, 2002tii
BMW 3 Series - 320i, 323i

--.

Transmission Mount - Priced Each

T#:593698

Part#: 22316771130

In Stock at Vendor

$ 64.04

This product was last offered at the strikethrough price on
04-06-2026

$ 21.58 USD

Add to Wish List

Qty

$ 21.58 USD

Add to Wish List

With bad transmission mounts, excessive vibration and noise is transferred to the cabin. The rubber in the mounts wear out over time and cause too much movement in the drivetrain. Replace them when wear is detected to keep everything tight.

Show More Show Less

Project Cars

SELECT YOUR BMW

Sub-Categories

Benefits:

Select Vehicle

Purpose

Category

Brand

Price

Special Offers

Shipping

Narrow Results