BMW Drivetrain Parts

JXB Driveshaft Center Support Bearing Carrier Upgrade - BMW E36 E46 Z...

T#:4988548

Part#: BMW04A0

In Stock

Starting at $ 299.99 USD

Add to Wish List

Starting at $ 299.99 USD

Add to Wish List

The stock center support bearing carrier is designed to reduce NVH to the cabin by loosely holding the center bearing with a flimsy rubber bushing. During launches and shifts, the driveshaft is allowed to travel off-center, decreasing throttle response and causing oscillations through the drivetrain. As they age, the carrier rubber sags and dry rots, ruining the driveshaft alignment. Fix or prevent this common issue with JXB Performance's Driveshaft Center Support Bearing Upgrade! JXB utilizes a simple but extremely effective 2-piece design which allows you to install this upgrade and replace bushings with ease. The stock center support carrier is simply cut away, allowing the JXB bushings to "clamp" down on the driveshaft bearing and hold the driveshaft securely in place, maintaining driveshaft alignment at all times.

Show More Show Less

BMW Clutch Stop - Bavarian Autosport

T#:1777897

Part#: B2300001KT

In Stock

Sale - Save 20% $ 26.99

This product was last offered at the strikethrough price on
05-03-2026

$ 21.59 USD

Add to Wish List

Qty

Sale - Save 20%

$ 26.99

This product was last offered at the strikethrough price on
05-03-2026

$ 21.59 USD

Add to Wish List

BMW Clutch Stop

Improve your shifting experience with the BMW Clutch Stop. This adjustable clutch stop is designed to install beneath the clutch pedal, allowing you to set the precise stopping point just after the clutch disengages. Once adjusted, you can achieve consistent, smooth, and efficient shifts every time, saving valuable time and effort.

Benefits:

Enhances shifting precision and consistency
Saves time with smooth and fast shifts
Adjustable design allows for personalized settings

Upgrade your BMW's shifting performance with the BMW Clutch Stop for a more enjoyable driving experience.

Show More Show Less

JXB Driveshaft Center Support Bearing Carrier - Street Bushings - BMW...

T#:4744858

Part#: BMW01A0-S

In Stock

$ 299.99 USD

Add to Wish List

Qty

$ 299.99 USD

Add to Wish List

The stock center support bearing carrier is engineered to minimize noise, vibration, and harshness (NVH) in the cabin by loosely securing the center bearing with a soft rubber bushing. However, this design allows the driveshaft to move off-center during launches and shifts, reducing throttle response and causing drivetrain oscillations. Over time, the rubber bushing can sag or dry rot, leading to misalignment of the driveshaft.

Prevent or fix this common problem with JXB Performance's Driveshaft Center Support Bearing Upgrade! This upgrade features a simple yet highly effective 2-piece design that makes installation and bushing replacement effortless. The stock carrier is cut away, and the JXB bushings securely "clamp" the driveshaft bearing in place, ensuring constant driveshaft alignment.

The Street bushing option from JXB is the most popular choice, offering a significant improvement over the stock design while keeping NVH levels minimal.

Note: Some light NVH, such as a soft hum, may occur at certain speeds. However, with a modified exhaust or open windows, it’s unlikely to be noticeable.

Installation is straightforward and doesn’t require removing the driveshaft. The 2-piece design clamps directly onto the OEM bearing, though removing the old carrier will require a cutting tool.

Need replacement or additional bushings? See T#4799658 for replacement street bushings.

Show More Show Less

JXB Driveshaft Center Support Bearing Carrier Upgrade - BMW E70/71 F1...

T#:6076533

Part#: BMW12A0

In Stock

Starting at $ 299.99 USD

Add to Wish List

Starting at $ 299.99 USD

Add to Wish List

The stock center support bearing carrier is designed to reduce NVH to the cabin by loosely holding the center bearing with a flimsy rubber bushing. During launches and shifts, the driveshaft is allowed to travel off-center, decreasing throttle response and causing oscillations through the drivetrain. As they age, the carrier rubber sags and dry rots, ruining the driveshaft alignment. Fix or prevent this common issue with JXB Performance's Driveshaft Center Support Bearing Upgrade! JXB utilizes a simple but extremely effective 2-piece design which allows you to install this upgrade and replace bushings with ease. The stock center support carrier is simply cut away, allowing the JXB bushings to "clamp" down on the driveshaft bearing and hold the driveshaft securely in place, maintaining driveshaft alignment at all times. Two bushing options are available for this kit, Street and Track, both of which are many times better than the stock bushings: The street bushings absorb most of the NVH from the drivetrain. Some light NVH is possible at some speeds in the form of a soft hum. (With a modified exhaust or windows down, you’ll probably never hear it) The track bushings are for those who want no-compromise drivetrain performance. These may create a substantial amount of cabin noise. Not sure which is for you? Try them both, they’re interchangeable! Installation does not require the removal of the driveshaft. The 2-part design clamps around the OEM bearing. The old carrier must be removed, so a cutting tool is required. Looking for replacement or additional bushings? See T#4799658 for replacement street bushings and T#4799659 for replacement track bushings.

Show More Show Less

JXB Driveshaft Center Support Bearing Carrier Upgrade - BMW E81/82/88...

T#:4744864

Part#: BMW01A0

In Stock

Starting at $ 299.99 USD

Add to Wish List

Starting at $ 299.99 USD

Add to Wish List

The stock center support bearing carrier is designed to reduce NVH to the cabin by loosely holding the center bearing with a flimsy rubber bushing. During launches and shifts, the driveshaft is allowed to travel off-center, decreasing throttle response and causing oscillations through the drivetrain. As they age, the carrier rubber sags and dry rots, ruining the driveshaft alignment. Fix or prevent this common issue with JXB Performance's Driveshaft Center Support Bearing Upgrade! JXB utilizes a simple but extremely effective 2-piece design which allows you to install this upgrade and replace bushings with ease. The stock center support carrier is simply cut away, allowing the JXB bushings to "clamp" down on the driveshaft bearing and hold the driveshaft securely in place, maintaining driveshaft alignment at all times.

Show More Show Less

Bav Auto Universal Flex Disc - Multiple BMW Applications

T#:639802

Part#: 26117511454

In Stock

Sale - Save 15% $ 49.99

This product was last offered at the strikethrough price on
05-03-2026

$ 42.49 USD

Add to Wish List

Qty

Sale - Save 15%

$ 49.99

This product was last offered at the strikethrough price on
05-03-2026

$ 42.49 USD

Add to Wish List

This replacement flex disc (aka: the guibo) is a vibration dampener mounted on the back of the transmission which connects to the driveshaft. When it has worn, it produces a terrible vibration throughout the car. It's especially noticeable at low speeds and when starting from a standstill. Oil leaking from the back of the transmission will significantly reduce its life. From 1974 to 2019, Bavarian Autosport was one of the premier vendors for BMW and MINI auto parts. We are happy to preserve the Bav Auto legacy by continuing to carry their high-quality products into the future. All Bav Auto parts will remain unchanged in design and sourced from the same OEM suppliers to ensure long-lasting reliability. We trust these parts, accessories, and upgrades so confidently that we back every Bavarian Autosport branded component with a 2-year warranty.

Show More Show Less

Bav Auto Automatic Transmission Filter Kit - E82/88 128, E9X 328, E83...

T#:639806

Part#: 24117593565

In Stock

Sale - Save 20% $ 39.99

This product was last offered at the strikethrough price on
05-03-2026

$ 31.99 USD

Add to Wish List

Qty

Sale - Save 20%

$ 39.99

This product was last offered at the strikethrough price on
05-03-2026

$ 31.99 USD

Add to Wish List

Remember to service your transmission at the recommended intervals to increase your transmission's life span and reliability! From 1974 to 2019, Bavarian Autosport was one of the premier vendors for BMW and MINI auto parts. We are happy to preserve the Bav Auto legacy by continuing to carry their high-quality products into the future. All Bav Auto parts will remain unchanged in design and sourced from the same OEM suppliers to ensure long-lasting reliability. We trust these parts, accessories, and upgrades so confidently that we back every Bavarian Autosport branded component with a 2-year warranty.

Show More Show Less

Bremmen Automatic Transmission Pan With Transmission Filter - F22 F30...

For GA8HP70, GA8HP76, GA8HP75, GA8HP51, GA8HP50, or GA8HP45Z automatic transmissions - Does not fit GA8P Hybrid Transmissions

T#:579886

Part#: 55182

In Stock

Sale - Save 17% $ 138.99

This product was last offered at the strikethrough price on
05-03-2026

$ 115.99 USD

Add to Wish List

Qty

Sale - Save 17%

$ 138.99

This product was last offered at the strikethrough price on
05-03-2026

$ 115.99 USD

Add to Wish List

GA8HP 8 speed automatic transmission. Automatic transmissions are reliable, shift smoothly, and can last without issue so long as they are properly maintained. Over time, the transmission fluid becomes thick and the filter becomes contaminated with small metal particles. This can cause excess wear, high transmission operating temperatures, and eventual failure. To prevent this we recommend changing your filter, fluid, and seals to ensure your transmission continues to operate flawlessly. We recommend filter and fluid changes every 50,000 miles. This item fits the following BMWs: E71,E89 Z4,F06,F10,F12,F13,F15,F16,F22,F25 X3,F26 X4,F30,F31,F32,F33,F34,F36

Show More Show Less

JXB Driveshaft Center Support Bearing Carrier Upgrade - G20 3-Series,...

T#:6076534

Part#: BMW13A0

In Stock

Starting at $ 299.99 USD

Add to Wish List

Starting at $ 299.99 USD

Add to Wish List

The stock center support bearing carrier is designed to reduce NVH to the cabin by loosely holding the center bearing with a flimsy rubber bushing. During launches and shifts, the driveshaft is allowed to travel off-center, decreasing throttle response and causing oscillations through the drivetrain. As they age, the carrier rubber sags and dry rots, ruining the driveshaft alignment. Fix or prevent this common issue with JXB Performance's Driveshaft Center Support Bearing Upgrade! JXB utilizes a simple but extremely effective 2-piece design which allows you to install this upgrade and replace bushings with ease. The stock center support carrier is simply cut away, allowing the JXB bushings to "clamp" down on the driveshaft bearing and hold the driveshaft securely in place, maintaining driveshaft alignment at all times. Two bushing options are available for this kit, Street and Track, both of which are many times better than the stock bushings: The street bushings absorb most of the NVH from the drivetrain. Some light NVH is possible at some speeds in the form of a soft hum. (With a modified exhaust or windows down, you’ll probably never hear it) The track bushings are for those who want no-compromise drivetrain performance. These may create a substantial amount of cabin noise. Not sure which is for you? Try them both, they’re interchangeable! Installation does not require the removal of the driveshaft. The 2-part design clamps around the OEM bearing. The old carrier must be removed, so a cutting tool is required. Looking for replacement or additional bushings? See T#4799658 for replacement street bushings and T#4799659 for replacement track bushings.

Show More Show Less

Aftermarket Automatic Transmission Oil Pan Gasket

T#:341304

Part#: 24117572618

Ships in 1 Business Day

$ 27.99 USD

Add to Wish List

Qty

$ 27.99 USD

Add to Wish List

E36 M3, MZ3 JB Racing Lightweight Aluminum Flywheel

T#:3771

Part#: 520-010-240

Ships in 9 Business Days

$ 602.00 USD

Add to Wish List

Qty

$ 602.00 USD

Add to Wish List

Aluminum flywheels are much lighter than the stock steel flywheel and that produces better throttle response and more available horsepower to the wheels for faster acceleration. The JB Racing aluminum flywheels are a direct replacement for the stock flywheel and work with stock clutch components for an easy upgrade with very little downside.

Modern flywheels are built with additional components and features that are designed to dampen and minimize vibrations from the engine and transmission. As a result they have become bloated in weight and that means more energy is used up just making the flywheel spin. The weight difference between an aluminum and steel flywheel is huge - sometimes more than 50% less. Without the additional mass, more energy can be diverted to where it counts most - moving the car. The flywheel and clutch is one of the first areas that engine builders address when making the rotating assembly lighter for race engines. The dampening effect is just not needed on cars that are focused on performance.

In addition to releasing more power to the wheels, the lighter flywheel allows the engine to spin more freely, which improves throttle response. Again, the difference is huge as you watch the revs build faster than before. With the engine spinning easier the power band comes up much sooner. The stock steel flywheel feels lazy in comparison. There is a driving adjustment required to get used to how much faster the engine revs but that's not really a downside.

The JB lightweight flywheel is designed to be used with a factory organic clutch - the same clutch kit that you would get from any BMW dealer. This makes replacement clutch components easy to source and inexpensive when compared to specialized racing clutches. By using the factory BMW clutch, JB has also made the whole assembly easy to live with when used on the street. The clutch behaves the same as it originally did - just with better throttle response and more power! The JB flywheel can also be rebuilt with a new clutch contact surface - you don't have to buy a new flywheel.

Aluminum flywheels are considered 'single-mass' flywheels because they do not have the same dampening designs as an original 'dual-mass' flywheel. With a single-mass design more noise and vibration may be noticeable. There are steps you can take to minimize the noise - heavier weight transmission oil and clutch discs with anti-rattle springs (sprung-hub clutch). In addition to the standard replacement clutches, we also sell Sachs Performance sprung hub clutches that also work with the JB flywheels.

Stock Flywheel Weight = 25.5lbs
JB Flywheel Weight = 10.0lbs

This item fits the following BMWs:
1995-1999 E36 BMW M3
1998-2002 Z3 BMW Z3 M Roadster M Coupe

Show More Show Less

E30 318i/is, E36 318i, Z3 1.9 JB Racing Lightweight Aluminum Flywheel...

T#:3769

Part#: 520-040-215

Back Ordered

11% off MSRP $ 765.00

MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.

$ 679.00 USD

Add to Wish List

Qty

11% off MSRP

$ 765.00

MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.

$ 679.00 USD

Add to Wish List

Aluminum flywheels are much lighter than the stock steel flywheel and that produces better throttle response and more available horsepower to the wheels for faster acceleration. The JB Racing aluminum flywheels are a direct replacement for the stock flywheel and work with stock clutch components for an easy upgrade with very little downside.

Modern flywheels are built with additional components and features that are designed to dampen and minimize vibrations from the engine and transmission. As a result they have become bloated in weight and that means more energy is used up just making the flywheel spin. The weight difference between an aluminum and steel flywheel is huge - sometimes more than 50% less. Without the additional mass, more energy can be diverted to where it counts most - moving the car. The flywheel and clutch is one of the first areas that engine builders address when making the rotating assembly lighter for race engines. The dampening effect is just not needed on cars that are focused on performance.

In addition to releasing more power to the wheels, the lighter flywheel allows the engine to spin more freely, which improves throttle response. Again, the difference is huge as you watch the revs build faster than before. With the engine spinning easier the power band comes up much sooner. The stock steel flywheel feels lazy in comparison. There is a driving adjustment required to get used to how much faster the engine revs but that's not really a downside.

The JB lightweight flywheel is designed to be used with a factory organic clutch - the same clutch kit that you would get from any BMW dealer. This makes replacement clutch components easy to source and inexpensive when compared to specialized racing clutches. By using the factory BMW clutch, JB has also made the whole assembly easy to live with when used on the street. The clutch behaves the same as it originally did - just with better throttle response and more power! The JB flywheel can also be rebuilt with a new clutch contact surface - you don't have to buy a new flywheel.

Aluminum flywheels are considered 'single-mass' flywheels because they do not have the same dampening designs as an original 'dual-mass' flywheel. With a single-mass design more noise and vibration may be noticeable. There are steps you can take to minimize the noise - heavier weight transmission oil and clutch discs with anti-rattle springs (sprung-hub clutch).

Stock Flywheel Weight = 27.0lbs
JB Flywheel Weight = 9.0lbs

This item fits the following BMWs:
1989-1992 E30 BMW 318i 318is 318ic
1992-1997 E36 BMW 318i 318is 318ti 318ic
1996-1997 Z3 BMW Z3 1.9

Show More Show Less

E60, E82, E85, E9X, E89 (N52 Engine) JB Racing Lightweight Aluminum F...

T#:2801

Part#: 520-200-240

In Stock

$ 714.00 USD

Add to Wish List

Qty

$ 714.00 USD

Add to Wish List

Aluminum flywheels are much lighter than the stock steel flywheel and that produces better throttle response and more available horsepower to the wheels for faster acceleration. The JB Racing aluminum flywheels are a direct replacement for the stock flywheel and work with stock clutch components for an easy upgrade with very little downside.

Modern flywheels are built with additional components and features that are designed to dampen and minimize vibrations from the engine and transmission. As a result they have become bloated in weight and that means more energy is used up just making the flywheel spin. The weight difference between an aluminum and steel flywheel is huge - sometimes more than 50% less. Without the additional mass, more energy can be diverted to where it counts most - moving the car. The flywheel and clutch is one of the first areas that engine builders address when making the rotating assembly lighter for race engines. The dampening effect is just not needed on cars that are focused on performance.

In addition to releasing more power to the wheels, the lighter flywheel allows the engine to spin more freely, which improves throttle response. Again, the difference is huge as you watch the revs build faster than before. With the engine spinning easier the power band comes up much sooner. The stock steel flywheel feels lazy in comparison. There is a driving adjustment required to get used to how much faster the engine revs but that's not really a downside.

The JB lightweight flywheel is designed to be used with a factory organic clutch - the same clutch kit that you would get from any BMW dealer. This makes replacement clutch components easy to source and inexpensive when compared to specialized racing clutches. By using the factory BMW clutch, JB has also made the whole assembly easy to live with when used on the street. The clutch behaves the same as it originally did - just with better throttle response and more power! The JB flywheel can also be rebuilt with a new clutch contact surface - you don't have to buy a new flywheel.

Aluminum flywheels are considered 'single-mass' flywheels because they do not have the same dampening designs as an original 'dual-mass' flywheel. With a single-mass design more noise and vibration may be noticeable. There are steps you can take to minimize the noise - heavier weight transmission oil and clutch discs with anti-rattle springs (sprung-hub clutch).

This JB flywheel replaces the stock flywheel and can be used with either the stock 228mm or stock 240mm clutch discs. Depending on the model you may have either clutch size in your car but this flywheel is compatible with both. You can install a 240mm clutch as a mild upgrade.

Stock Flywheel Weight = 24-31.0lbs
JB Flywheel Weight = 12.0lbs

This item fits the following BMWs:
2006-2010 E60 BMW - 525i, 528i, 530i
2006-2013 E90, E91, E92, E93 BMW - 325i, 328i, 330i
2007-2013 E82 BMW - 125i, 128i
2006-2008 E85, E86 BMW - Z4 3.0i, Z4 3.0si
2009-later E89 BMW - Z4 3.0i

Show More Show Less

Driveshaft Carrier Spare Bushing Set - Track

Spare bushings only - does not include new carrier assembly

T#:4799659

Part#: BSH04A1

In Stock

$ 29.99 USD

Add to Wish List

Qty

$ 29.99 USD

Add to Wish List

Refresh all bushings in your driveshaft carrier kit. Please note that the bushings you receive will depend on your specific model of carrier and may not match the picture.

Driveshaft Carrier Spare Bushing Set - Street

Spare bushings only - does not include new carrier assembly

T#:4799658

Part#: BSH04A0

Ships in 4 Business Days

$ 29.99 USD

Add to Wish List

Qty

$ 29.99 USD

Add to Wish List

Refresh all bushings in your driveshaft carrier kit. Please note that the bushings you receive will depend on your specific model of carrier and may not match the picture.

Bav Auto Universal Flex Disc "Guibo" - E36 E46 E34 Z3 Z4 M Models ...

T#:1135777

Part#: 26112226527

In Stock

Sale - Save 10% $ 73.99

This product was last offered at the strikethrough price on
05-03-2026

$ 66.59 USD

Add to Wish List

Qty

Sale - Save 10%

$ 73.99

This product was last offered at the strikethrough price on
05-03-2026

$ 66.59 USD

Add to Wish List

This Bav Auto replacement flex disc (aka: the guibo) is a vibration dampener mounted on the back of the transmission which connects to the driveshaft. When it has worn, it can produce knocking sounds and a terrible vibration throughout the car. It's especially noticeable at low speeds and when starting from a standstill. Oil leaking from the back of the transmission will significantly reduce its life. This can also be used as an upgrade on the E30 M3. It has much more rubber in between the bolt holes which makes it last longer. This is 5mm thicker than the stock E30 flex disc so adjustment of the 2-piece driveshaft may be required. The original flex disc bolts can be re-used.

Show More Show Less

E46 M3 6MT JB Racing Lightweight Aluminum Flywheel

T#:302739

Part#: 520-180-240

Ships in 8 Business Days

$ 602.00 USD

Add to Wish List

Qty

$ 602.00 USD

Add to Wish List

Aluminum flywheels are much lighter than the stock steel flywheel and that produces better throttle response and more available horsepower to the wheels for faster acceleration. The JB Racing aluminum flywheels are a direct replacement for the stock flywheel and work with stock clutch components for an easy upgrade with very little downside.

Modern flywheels are built with additional components and features that are designed to dampen and minimize vibrations from the engine and transmission. As a result they have become bloated in weight and that means more energy is used up just making the flywheel spin. The weight difference between an aluminum and steel flywheel is huge - sometimes more than 50% less. Without the additional mass, more energy can be diverted to where it counts most - moving the car. The flywheel and clutch is one of the first areas that engine builders address when making the rotating assembly lighter for race engines. The dampening effect is just not needed on cars that are focused on performance.

In addition to releasing more power to the wheels, the lighter flywheel allows the engine to spin more freely, which improves throttle response. Again, the difference is huge as you watch the revs build faster than before. With the engine spinning easier the power band comes up much sooner. The stock steel flywheel feels lazy in comparison. There is a driving adjustment required to get used to how much faster the engine revs but that's not really a downside.

The JB lightweight flywheel is designed to be used with a factory organic clutch - the same clutch kit that you would get from any BMW dealer. This makes replacement clutch components easy to source and inexpensive when compared to specialized racing clutches. By using the factory BMW clutch, JB has also made the whole assembly easy to live with when used on the street. The clutch behaves the same as it originally did - just with better throttle response and more power! The JB flywheel can also be rebuilt with a new clutch contact surface - you don't have to buy a new flywheel.

Aluminum flywheels are considered 'single-mass' flywheels because they do not have the same dampening designs as an original 'dual-mass' flywheel. With a single-mass design more noise and vibration may be noticeable. There are steps you can take to minimize the noise - heavier weight transmission oil and clutch discs with anti-rattle springs (sprung-hub clutch). In addition to the standard replacement clutches, we also sell Sachs Performance sprung hub clutches that also work with the JB flywheels.

Stock Flywheel Weight = 25.0lbs
JB Flywheel Weight = 10.0lbs

This item fits the following BMWs:
2001-2006 E46 BMW M3 (6-speed manual only, not for SMG)

Show More Show Less

E46 323/325/328/330 5-speed, Z3 2.3/2.8/3.0 JB Racing Lightweight Alu...

T#:4227

Part#: 520-140-240

In Stock

$ 602.00 USD

Add to Wish List

Qty

$ 602.00 USD

Add to Wish List

Aluminum flywheels are much lighter than the stock steel flywheel and that produces better throttle response and more available horsepower to the wheels for faster acceleration. The JB Racing aluminum flywheels are a direct replacement for the stock flywheel and work with stock clutch components for an easy upgrade with very little downside.

Modern flywheels are built with additional components and features that are designed to dampen and minimize vibrations from the engine and transmission. As a result they have become bloated in weight and that means more energy is used up just making the flywheel spin. The weight difference between an aluminum and steel flywheel is huge - sometimes more than 50% less. Without the additional mass, more energy can be diverted to where it counts most - moving the car. The flywheel and clutch is one of the first areas that engine builders address when making the rotating assembly lighter for race engines. The dampening effect is just not needed on cars that are focused on performance.

In addition to releasing more power to the wheels, the lighter flywheel allows the engine to spin more freely, which improves throttle response. Again, the difference is huge as you watch the revs build faster than before. With the engine spinning easier the power band comes up much sooner. The stock steel flywheel feels lazy in comparison. There is a driving adjustment required to get used to how much faster the engine revs but that's not really a downside.

The JB lightweight flywheel is designed to be used with a factory organic clutch - the same clutch kit that you would get from any BMW dealer. This makes replacement clutch components easy to source and inexpensive when compared to specialized racing clutches. By using the factory BMW clutch, JB has also made the whole assembly easy to live with when used on the street. The clutch behaves the same as it originally did - just with better throttle response and more power! The JB flywheel can also be rebuilt with a new clutch contact surface - you don't have to buy a new flywheel.

Aluminum flywheels are considered 'single-mass' flywheels because they do not have the same dampening designs as an original 'dual-mass' flywheel. With a single-mass design more noise and vibration may be noticeable. There are steps you can take to minimize the noise - heavier weight transmission oil and clutch discs with anti-rattle springs (sprung-hub clutch). In addition to the standard replacement clutches, we also sell Sachs Performance sprung hub clutches that also work with the JB flywheels.

Stock Flywheel Weight = 25.0lbs
JB Flywheel Weight = 10.0lbs

This item fits the following BMWs:
1999-2002 E46 BMW 323i 323ci 325i 325ci 328i 328ci 330i 330ci (with 5-speed manual transmission)
2001-2005 E46 BMW 325xi 330xi
1997-2002 Z3 BMW Z3 2.3 Z3 2.5i Z3 2.8 Z3 3.0i

Show More Show Less

JXB Driveshaft Center Support Bearing Carrier Upgrade - BMW E39 540i ...

T#:6061694

Part#: BMW06A0

Ships in 1 Business Day

Starting at $ 299.99 USD

Add to Wish List

Starting at $ 299.99 USD

Add to Wish List

The stock center support bearing carrier is designed to reduce NVH to the cabin by loosely holding the center bearing with a flimsy rubber bushing. During launches and shifts, the driveshaft is allowed to travel off-center, decreasing throttle response and causing oscillations through the drivetrain. As they age, the carrier rubber sags and dry rots, ruining the driveshaft alignment. Fix or prevent this common issue with JXB Performance's Driveshaft Center Support Bearing Upgrade! JXB utilizes a simple but extremely effective 2-piece design which allows you to install this upgrade and replace bushings with ease. The stock center support carrier is simply cut away, allowing the JXB bushings to "clamp" down on the driveshaft bearing and hold the driveshaft securely in place, maintaining driveshaft alignment at all times. Two bushing options are available for this kit, Street and Track, both of which are many times better than the stock bushings: The street bushings absorb most of the NVH from the drivetrain. Some light NVH is possible at some speeds in the form of a soft hum. (With a modified exhaust or windows down, you’ll probably never hear it) The track bushings are for those who want no-compromise drivetrain performance. These may create a substantial amount of cabin noise. Not sure which is for you? Try them both, they’re interchangeable! Installation does not require the removal of the driveshaft. The 2-part design clamps around the OEM bearing. The old carrier must be removed, so a cutting tool is required. Looking for replacement or additional bushings? See T#4799658 for replacement street bushings and T#4799659 for replacement track bushings.

Show More Show Less

E30 M3 JB Racing Lightweight Aluminum Flywheel

T#:3768

Part#: 520-050-228

Ships in 4 Business Days

$ 630.00 USD

Add to Wish List

Qty

$ 630.00 USD

Add to Wish List

Aluminum flywheels are much lighter than the stock steel flywheel and that produces better throttle response and more available horsepower to the wheels for faster acceleration. The JB Racing aluminum flywheels are a direct replacement for the stock flywheel and work with stock clutch components for an easy upgrade with very little downside.

Modern flywheels are built with additional components and features that are designed to dampen and minimize vibrations from the engine and transmission. As a result they have become bloated in weight and that means more energy is used up just making the flywheel spin. The weight difference between an aluminum and steel flywheel is huge - sometimes more than 50% less. Without the additional mass, more energy can be diverted to where it counts most - moving the car. The flywheel and clutch is one of the first areas that engine builders address when making the rotating assembly lighter for race engines. The dampening effect is just not needed on cars that are focused on performance.

In addition to releasing more power to the wheels, the lighter flywheel allows the engine to spin more freely, which improves throttle response. Again, the difference is huge as you watch the revs build faster than before. With the engine spinning easier the power band comes up much sooner. The stock steel flywheel feels lazy in comparison. There is a driving adjustment required to get used to how much faster the engine revs but that's not really a downside.

The JB lightweight flywheel is designed to be used with a factory organic clutch - the same clutch kit that you would get from any BMW dealer. This makes replacement clutch components easy to source and inexpensive when compared to specialized racing clutches. By using the factory BMW clutch, JB has also made the whole assembly easy to live with when used on the street. The clutch behaves the same as it originally did - just with better throttle response and more power! The JB flywheel can also be rebuilt with a new clutch contact surface - you don't have to buy a new flywheel.

Aluminum flywheels are considered 'single-mass' flywheels because they do not have the same dampening designs as an original 'dual-mass' flywheel. With a single-mass design more noise and vibration may be noticeable. There are steps you can take to minimize the noise - heavier weight transmission oil and clutch discs with anti-rattle springs (sprung-hub clutch).

The JB flywheel includes ignition trigger wheel.

Stock Flywheel Weight = 19.5lbs
JB Flywheel Weight = 8.0lbs

This item fits the following BMWs:
1987-1991 E30 BMW M3

Show More Show Less

JB Racing Single Mass Lightweight Aluminum Flywheel - 6-speed - E46 3...

T#:3474

Part#: 520-190-240

Ships in 2 Business Days

$ 672.00 USD

Add to Wish List

Qty

$ 672.00 USD

Add to Wish List

This is a performance replacement for BMW Part # 21207533868 Aluminum flywheels are much lighter than the stock steel flywheel and that produces better throttle response and more available horsepower to the wheels for faster acceleration. The JB Racing aluminum flywheels are a direct replacement for the stock flywheel and work with stock clutch components for an easy upgrade with very little downside.

Modern flywheels are built with additional components and features that are designed to dampen and minimize vibrations from the engine and transmission. As a result they have become bloated in weight and that means more energy is used up just making the flywheel spin. The weight difference between an aluminum and steel flywheel is huge - sometimes more than 50% less. Without the additional mass, more energy can be diverted to where it counts most - moving the car. The flywheel and clutch is one of the first areas that engine builders address when making the rotating assembly lighter for race engines. The dampening effect is just not needed on cars that are focused on performance.

In addition to releasing more power to the wheels, the lighter flywheel allows the engine to spin more freely, which improves throttle response. Again, the difference is huge as you watch the revs build faster than before. With the engine spinning easier the power band comes up much sooner. The stock steel flywheel feels lazy in comparison. There is a driving adjustment required to get used to how much faster the engine revs but that's not really a downside.

The JB lightweight flywheel is designed to be used with a factory organic clutch - the same clutch kit that you would get from any BMW dealer. This makes replacement clutch components easy to source and inexpensive when compared to specialized racing clutches. By using the factory BMW clutch, JB has also made the whole assembly easy to live with when used on the street. The clutch behaves the same as it originally did - just with better throttle response and more power! The JB flywheel can also be rebuilt with a new clutch contact surface - you don't have to buy a new flywheel.

Aluminum flywheels are considered 'single-mass' flywheels because they do not have the same dampening designs as an original 'dual-mass' flywheel. With a single-mass design more noise and vibration may be noticeable. There are steps you can take to minimize the noise - heavier weight transmission oil and clutch discs with anti-rattle springs (sprung-hub clutch).

The JB Flywheel includes the pilot bearing mounted in the flywheel hub, just like the factory configuration.

Stock Flywheel Weight = 25.0lbs
JB Flywheel Weight = 10.5lbs

This item fits the following BMWs:
2002-2005 E46 BMW 325i 330i (with 6-speed manual transmission)

Show More Show Less

E30 325i, E34 525i (M20) JB Racing Lightweight Aluminum Flywheel (Rep...

T#:385699

Part#: 520-060-228

Ships on Aug 28, 2026

$ 581.00 USD

Add to Wish List

Qty

$ 581.00 USD

Add to Wish List

Aluminum flywheels are much lighter than the stock steel flywheel and that produces better throttle response and more available horsepower to the wheels for faster acceleration. The JB Racing aluminum flywheels are a direct replacement for the stock flywheel and work with stock clutch components for an easy upgrade with very little downside.

Modern flywheels are built with additional components and features that are designed to dampen and minimize vibrations from the engine and transmission. As a result they have become bloated in weight and that means more energy is used up just making the flywheel spin. The weight difference between an aluminum and steel flywheel is huge - sometimes more than 50% less. Without the additional mass, more energy can be diverted to where it counts most - moving the car. The flywheel and clutch is one of the first areas that engine builders address when making the rotating assembly lighter for race engines. The dampening effect is just not needed on cars that are focused on performance.

In addition to releasing more power to the wheels, the lighter flywheel allows the engine to spin more freely, which improves throttle response. Again, the difference is huge as you watch the revs build faster than before. With the engine spinning easier the power band comes up much sooner. The stock steel flywheel feels lazy in comparison. There is a driving adjustment required to get used to how much faster the engine revs but that's not really a downside.

The JB lightweight flywheel is designed to be used with a factory organic clutch - the same clutch kit that you would get from any BMW dealer. This makes replacement clutch components easy to source and inexpensive when compared to specialized racing clutches. By using the factory BMW clutch, JB has also made the whole assembly easy to live with when used on the street. The clutch behaves the same as it originally did - just with better throttle response and more power! The JB flywheel can also be rebuilt with a new clutch contact surface - you don't have to buy a new flywheel.

Aluminum flywheels are considered 'single-mass' flywheels because they do not have the same dampening designs as an original 'dual-mass' flywheel. With a single-mass design more noise and vibration may be noticeable. There are steps you can take to minimize the noise - heavier weight transmission oil and clutch discs with anti-rattle springs (sprung-hub clutch).

This flywheel replaces the stock original single-mass flywheel and should only be used with the corresponding 'single-mass' clutch kit. According to BMW the single mass flywheel was installed in all 325i up to 12/86 production date but we have seen some later cars with a single-mass flywheel. The age of the car almost guarantees one or more clutch replacements and possibly a change to the original flywheel as well. You may not know which flywheel is currently installed until the flywheel cover or the transmission is removed.

Stock Flywheel Weight = 18.0lbs
JB Flywheel Weight = 8.0lbs

This item fits the following BMWs:
1984-1991 E30 BMW 325i 325ic 325is (with single-mass flywheel)
1989-1990 E34 BMW 525i (with single-mass flywheel)

Show More Show Less

JXB Driveshaft Center Support Bearing Carrier Upgrade - BMW E60/61 E6...

T#:22394036

Part#: 4744865TCKTS6J5G

In Stock

$ 299.99 USD

Add to Wish List

Qty

$ 299.99 USD

Add to Wish List

JXB Driveshaft Center Support Bearing Carrier Upgrade - BMW E30 RWD (...

T#:6061687

Part#: BMW03A0

In Stock

Starting at $ 299.99 USD

Add to Wish List

Starting at $ 299.99 USD

Add to Wish List

The stock center support bearing carrier is designed to reduce NVH to the cabin by loosely holding the center bearing with a flimsy rubber bushing. During launches and shifts, the driveshaft is allowed to travel off-center, decreasing throttle response and causing oscillations through the drivetrain. As they age, the carrier rubber sags and dry rots, ruining the driveshaft alignment. Fix or prevent this common issue with JXB Performance's Driveshaft Center Support Bearing Upgrade! JXB utilizes a simple but extremely effective 2-piece design which allows you to install this upgrade and replace bushings with ease. The stock center support carrier is simply cut away, allowing the JXB bushings to "clamp" down on the driveshaft bearing and hold the driveshaft securely in place, maintaining driveshaft alignment at all times. Two bushing options are available for this kit, Street and Track, both of which are many times better than the stock bushings: The street bushings absorb most of the NVH from the drivetrain. Some light NVH is possible at some speeds in the form of a soft hum. (With a modified exhaust or windows down, you’ll probably never hear it) The track bushings are for those who want no-compromise drivetrain performance. These may create a substantial amount of cabin noise. Not sure which is for you? Try them both, they’re interchangeable! Installation does not require the removal of the driveshaft. The 2-part design clamps around the OEM bearing. The old carrier must be removed, so a cutting tool is required. Looking for replacement or additional bushings? See T#4799658 for replacement street bushings and T#4799659 for replacement track bushings.

Show More Show Less

E34 M5 JB Racing Lightweight Aluminum Flywheel

T#:3772

Part#: 520-090-240

Ships in 9 Business Days

$ 581.00 USD

Add to Wish List

Qty

$ 581.00 USD

Add to Wish List

Aluminum flywheels are much lighter than the stock steel flywheel and that produces better throttle response and more available horsepower to the wheels for faster acceleration. The JB Racing aluminum flywheels are a direct replacement for the stock flywheel and work with stock clutch components for an easy upgrade with very little downside.

Modern flywheels are built with additional components and features that are designed to dampen and minimize vibrations from the engine and transmission. As a result they have become bloated in weight and that means more energy is used up just making the flywheel spin. The weight difference between an aluminum and steel flywheel is huge - sometimes more than 50% less. Without the additional mass, more energy can be diverted to where it counts most - moving the car. The flywheel and clutch is one of the first areas that engine builders address when making the rotating assembly lighter for race engines. The dampening effect is just not needed on cars that are focused on performance.

In addition to releasing more power to the wheels, the lighter flywheel allows the engine to spin more freely, which improves throttle response. Again, the difference is huge as you watch the revs build faster than before. With the engine spinning easier the power band comes up much sooner. The stock steel flywheel feels lazy in comparison. There is a driving adjustment required to get used to how much faster the engine revs but that's not really a downside.

The JB lightweight flywheel is designed to be used with a factory organic clutch - the same clutch kit that you would get from any BMW dealer. This makes replacement clutch components easy to source and inexpensive when compared to specialized racing clutches. By using the factory BMW clutch, JB has also made the whole assembly easy to live with when used on the street. The clutch behaves the same as it originally did - just with better throttle response and more power! The JB flywheel can also be rebuilt with a new clutch contact surface - you don't have to buy a new flywheel.

Aluminum flywheels are considered 'single-mass' flywheels because they do not have the same dampening designs as an original 'dual-mass' flywheel. With a single-mass design more noise and vibration may be noticeable.

Stock Flywheel Weight = 16.0lbs
JB Flywheel Weight = 8.0lbs

This item fits the following BMWs:
1991-1995 E34 BMW M5

Show More Show Less

Transmission Filter Kit

T#:587717

Part#: 24117533699S1

In Stock at Vendor

$ 47.99 USD

Add to Wish List

Qty

$ 47.99 USD

Add to Wish List

2002, E21 320i, E30 318i (M10) JB Racing Lightweight Aluminum Flywhee...

T#:3647

Part#: 520-110-215

Ships in 2 Business Days

$ 581.00 USD

Add to Wish List

Qty

$ 581.00 USD

Add to Wish List

Aluminum flywheels are much lighter than the stock steel flywheel and that produces better throttle response and more available horsepower to the wheels for faster acceleration. The JB Racing aluminum flywheels are a direct replacement for the stock flywheel and work with stock clutch components for an easy upgrade with very little downside.

Modern flywheels are built with additional components and features that are designed to dampen and minimize vibrations from the engine and transmission. As a result they have become bloated in weight and that means more energy is used up just making the flywheel spin. The weight difference between an aluminum and steel flywheel is huge - sometimes more than 50% less. Without the additional mass, more energy can be diverted to where it counts most - moving the car. The flywheel and clutch is one of the first areas that engine builders address when making the rotating assembly lighter for race engines. The dampening effect is just not needed on cars that are focused on performance.

In addition to releasing more power to the wheels, the lighter flywheel allows the engine to spin more freely, which improves throttle response. Again, the difference is huge as you watch the revs build faster than before. With the engine spinning easier the power band comes up much sooner. The stock steel flywheel feels lazy in comparison. There is a driving adjustment required to get used to how much faster the engine revs but that's not really a downside.

The JB lightweight flywheel is designed to be used with a factory organic clutch - the same clutch kit that you would get from any BMW dealer. This makes replacement clutch components easy to source and inexpensive when compared to specialized racing clutches. By using the factory BMW clutch, JB has also made the whole assembly easy to live with when used on the street. The clutch behaves the same as it originally did - just with better throttle response and more power! The JB flywheel can be rebuilt too with a new clutch contact surface.

Aluminum flywheels are considered 'single-mass' flywheels because they do not have the same dampening designs as an original 'dual-mass' flywheel. With a single-mass design more noise and vibration may be noticeable. There are steps you can take to minimize the noise - heavier weight transmission oil and clutch discs with anti-rattle springs (sprung-hub clutch).

Stock Flywheel Weight = 16.5lbs
JB Flywheel Weight = 8lbs

This item fits the following BMWs:
1974-1976 2002 BMW 2002
1977-1983 E21 BMW 320i
1984-1985 E30 BMW 318i

Show More Show Less

JXB Driveshaft Center Support Bearing Carrier Upgrade - BMW E60/61 E6...

T#:4744865

Part#: BMW02A0

Ships in 1 Business Day

Starting at $ 299.99 USD

Add to Wish List

Starting at $ 299.99 USD

Add to Wish List

The stock center support bearing carrier is designed to reduce NVH to the cabin by loosely holding the center bearing with a flimsy rubber bushing. During launches and shifts, the driveshaft is allowed to travel off-center, decreasing throttle response and causing oscillations through the drivetrain. As they age, the carrier rubber sags and dry rots, ruining the driveshaft alignment. Fix or prevent this common issue with JXB Performance's Driveshaft Center Support Bearing Upgrade! JXB utilizes a simple but extremely effective 2-piece design which allows you to install this upgrade and replace bushings with ease. The stock center support carrier is simply cut away, allowing the JXB bushings to "clamp" down on the driveshaft bearing and hold the driveshaft securely in place, maintaining driveshaft alignment at all times.

Show More Show Less

Shaft Seal

2X Entries For Our G87 M2 Sweepstakes! We Price Match - Give Us A Call or Chat!

T#:591509

Part#: 11117568263

In Stock

$ 22.99 USD

Add to Wish List

Qty

$ 22.99 USD

Add to Wish List

Ideal for engine repairs or addressing leaks into the transmission bell housing, this shaft seal is designed to be mounted on the engine block's upper and lower halves, facing towards the transmission housing.

Show More Show Less

E39 540i 97-03 JB Racing Lightweight Aluminum Flywheel

T#:1339

Part#: 520-150-240

In Stock

$ 903.00 USD

Add to Wish List

Qty

$ 903.00 USD

Add to Wish List

Aluminum flywheels are much lighter than the stock steel flywheel and that produces better throttle response and more available horsepower to the wheels for faster acceleration. The JB Racing aluminum flywheels are a direct replacement for the stock flywheel and work with stock clutch components for an easy upgrade with very little downside.

Modern flywheels are built with additional components and features that are designed to dampen and minimize vibrations from the engine and transmission. As a result they have become bloated in weight and that means more energy is used up just making the flywheel spin. The weight difference between an aluminum and steel flywheel is huge - sometimes more than 50% less. Without the additional mass, more energy can be diverted to where it counts most - moving the car. The flywheel and clutch is one of the first areas that engine builders address when making the rotating assembly lighter for race engines. The dampening effect is just not needed on cars that are focused on performance.

In addition to releasing more power to the wheels, the lighter flywheel allows the engine to spin more freely, which improves throttle response. Again, the difference is huge as you watch the revs build faster than before. With the engine spinning easier the power band comes up much sooner. The stock steel flywheel feels lazy in comparison. There is a driving adjustment required to get used to how much faster the engine revs but that's not really a downside.

The JB lightweight flywheel is designed to be used with a factory organic clutch - the same clutch kit that you would get from any BMW dealer. This makes replacement clutch components easy to source and inexpensive when compared to specialized racing clutches. By using the factory BMW clutch, JB has also made the whole assembly easy to live with when used on the street. The clutch behaves the same as it originally did - just with better throttle response and more power! The JB flywheel can also be rebuilt with a new clutch contact surface - you don't have to buy a new flywheel.

Aluminum flywheels are considered 'single-mass' flywheels because they do not have the same dampening designs as an original 'dual-mass' flywheel. With a single-mass design more noise and vibration may be noticeable. There are steps you can take to minimize the noise - heavier weight transmission oil and clutch discs with anti-rattle springs (sprung-hub clutch).

Stock Flywheel Weight = 33.0lbs
JB Flywheel Weight = 13.0lbs

This item fits the following BMWs:
1997-2003 E39 BMW 540i

Show More Show Less

JXB Driveshaft Center Support Bearing Carrier Upgrade - BMW F01/02 7-...

T#:6076536

Part#: BMW14A0

In Stock

Starting at $ 299.99 USD

Add to Wish List

Starting at $ 299.99 USD

Add to Wish List

The stock center support bearing carrier is designed to reduce NVH to the cabin by loosely holding the center bearing with a flimsy rubber bushing. During launches and shifts, the driveshaft is allowed to travel off-center, decreasing throttle response and causing oscillations through the drivetrain. As they age, the carrier rubber sags and dry rots, ruining the driveshaft alignment. Fix or prevent this common issue with JXB Performance's Driveshaft Center Support Bearing Upgrade! JXB utilizes a simple but extremely effective 2-piece design which allows you to install this upgrade and replace bushings with ease. The stock center support carrier is simply cut away, allowing the JXB bushings to "clamp" down on the driveshaft bearing and hold the driveshaft securely in place, maintaining driveshaft alignment at all times. Two bushing options are available for this kit, Street and Track, both of which are many times better than the stock bushings: The street bushings absorb most of the NVH from the drivetrain. Some light NVH is possible at some speeds in the form of a soft hum. (With a modified exhaust or windows down, you’ll probably never hear it) The track bushings are for those who want no-compromise drivetrain performance. These may create a substantial amount of cabin noise. Not sure which is for you? Try them both, they’re interchangeable! Installation does not require the removal of the driveshaft. The 2-part design clamps around the OEM bearing. The old carrier must be removed, so a cutting tool is required. Looking for replacement or additional bushings? See T#4799658 for replacement street bushings and T#4799659 for replacement track bushings.

Show More Show Less

JXB Driveshaft Center Support Bearing Carrier Upgrade - BMW E85/E86 Z...

T#:18070238

Part#: 7687533TCKHMEMIR

In Stock at Vendor

$ 299.99 USD

Add to Wish List

Qty

$ 299.99 USD

Add to Wish List

E24 633/635CSi/M6, E28 535i/M5 JB Racing Lightweight Aluminum Flywhee...

T#:3770

Part#: 520-080-240

Ships in 8 Business Days

$ 630.00 USD

Add to Wish List

Qty

$ 630.00 USD

Add to Wish List

Aluminum flywheels are much lighter than the stock steel flywheel and that produces better throttle response and more available horsepower to the wheels for faster acceleration. The JB Racing aluminum flywheels are a direct replacement for the stock flywheel and work with stock clutch components for an easy upgrade with very little downside.

Modern flywheels are built with additional components and features that are designed to dampen and minimize vibrations from the engine and transmission. As a result they have become bloated in weight and that means more energy is used up just making the flywheel spin. The weight difference between an aluminum and steel flywheel is huge - sometimes more than 50% less. Without the additional mass, more energy can be diverted to where it counts most - moving the car. The flywheel and clutch is one of the first areas that engine builders address when making the rotating assembly lighter for race engines. The dampening effect is just not needed on cars that are focused on performance.

In addition to releasing more power to the wheels, the lighter flywheel allows the engine to spin more freely, which improves throttle response. Again, the difference is huge as you watch the revs build faster than before. With the engine spinning easier the power band comes up much sooner. The stock steel flywheel feels lazy in comparison. There is a driving adjustment required to get used to how much faster the engine revs but that's not really a downside.

The JB lightweight flywheel is designed to be used with a factory organic clutch - the same clutch kit that you would get from any BMW dealer. This makes replacement clutch components easy to source and inexpensive when compared to specialized racing clutches. By using the factory BMW clutch, JB has also made the whole assembly easy to live with when used on the street. The clutch behaves the same as it originally did - just with better throttle response and more power! The JB flywheel can also be rebuilt with a new clutch contact surface - you don't have to buy a new flywheel.

Aluminum flywheels are considered 'single-mass' flywheels because they do not have the same dampening designs as an original 'dual-mass' flywheel. With a single-mass design more noise and vibration may be noticeable. There are steps you can take to minimize the noise - heavier weight transmission oil and clutch discs with anti-rattle springs (sprung-hub clutch).

Stock Flywheel Weight = 22.0lbs
JB Flywheel Weight = 8.5lbs

This flywheel includes the ignition trigger wheel.

This item fits the following BMWs:
1982-1987 E23 BMW 733i 735i
1982-1989 E24 BMW 633csi 635csi M6
1985-1988 E28 BMW 535i 535is M5

Show More Show Less

JXB Driveshaft Center Support Bearing Carrier Upgrade

T#:25772541

Part#: 4507854PDKNGJY2Q

Ships in 4 Business Days

$ 299.99 USD

Add to Wish List

Qty

$ 299.99 USD

Add to Wish List

JXB Driveshaft Center Support Bearing Carrier Upgrade - BMW E85/E86 E...

T#:7687533

Part#: BMW15A0

In Stock at Vendor

Starting at $ 299.99 USD

Add to Wish List

Starting at $ 299.99 USD

Add to Wish List

The stock center support bearing carrier is designed to reduce NVH to the cabin by loosely holding the center bearing with a flimsy rubber bushing. During launches and shifts, the driveshaft is allowed to travel off-center, decreasing throttle response and causing oscillations through the drivetrain. As they age, the carrier rubber sags and dry rots, ruining the driveshaft alignment. Fix or prevent this common issue with JXB Performance's Driveshaft Center Support Bearing Upgrade! JXB utilizes a simple but extremely effective 2-piece design which allows you to install this upgrade and replace bushings with ease. The stock center support carrier is simply cut away, allowing the JXB bushings to "clamp" down on the driveshaft bearing and hold the driveshaft securely in place, maintaining driveshaft alignment at all times. Two bushing options are available for this kit, Street and Track, both of which are many times better than the stock bushings: The street bushings absorb most of the NVH from the drivetrain. Some light NVH is possible at some speeds in the form of a soft hum. (With a modified exhaust or windows down, you’ll probably never hear it) The track bushings are for those who want no-compromise drivetrain performance. These may create a substantial amount of cabin noise. Not sure which is for you? Try them both, they’re interchangeable! Installation does not require the removal of the driveshaft. The 2-part design clamps around the OEM bearing. The old carrier must be removed, so a cutting tool is required. Looking for replacement or additional bushings? See T#4799658 for replacement street bushings and T#4799659 for replacement track bushings.

Show More Show Less

Driveshaft Center Support Bearing Carrier - Track Bushings

T#:6151348

Part#: BMW13A0-T

Ships in 4 Business Days

$ 299.99 USD

Add to Wish List

Qty

$ 299.99 USD

Add to Wish List

The stock center support bearing carrier utilizes an extremely thin layer of rubber to secure the driveshaft, allowing for minimal movement to effectively insulate the cabin from noise, vibration, and harshness (NVH). However, this design is less effective at maintaining proper bearing alignment under heavy loads. Over time, it allows the bearing to gradually sag, disrupting the driveshaft alignment and introducing play in the driveline during gear shifts and throttle application. The original equipment manufacturer (OEM) rubber bushing has a tendency to sag, become brittle, and eventually deteriorate, resulting in dry rot and cracking. Even in well-maintained vehicles, the stock bushing can develop cracks in as little as 5-10 years. When the bushing loses its integrity, it can lead to pronounced vibrations, clunking noises, and increased stress on the bearing. Adding to the challenge, the stock carrier is permanently molded onto the center support bearing, making replacement a difficult task that typically necessitates specialized tools.

Show More Show Less

JB Racing Lightweight Aluminum Flywheel - E39 M5

T#:16606

Part#: 520-160-240

Ships in 8 Business Days

$ 903.00 USD

Add to Wish List

Qty

$ 903.00 USD

Add to Wish List

Aluminum flywheels are much lighter than the stock steel flywheel and that produces better throttle response and more available horsepower to the wheels for faster acceleration. The JB Racing aluminum flywheels are a direct replacement for the stock flywheel and work with stock clutch components for an easy upgrade with very little downside.

Modern flywheels are built with additional components and features that are designed to dampen and minimize vibrations from the engine and transmission. As a result they have become bloated in weight and that means more energy is used up just making the flywheel spin. The weight difference between an aluminum and steel flywheel is huge - sometimes more than 50% less. Without the additional mass, more energy can be diverted to where it counts most - moving the car. The flywheel and clutch is one of the first areas that engine builders address when making the rotating assembly lighter for race engines. The dampening effect is just not needed on cars that are focused on performance.

In addition to releasing more power to the wheels, the lighter flywheel allows the engine to spin more freely, which improves throttle response. Again, the difference is huge as you watch the revs build faster than before. With the engine spinning easier the power band comes up much sooner. The stock steel flywheel feels lazy in comparison. There is a driving adjustment required to get used to how much faster the engine revs but that's not really a downside.

The JB lightweight flywheel is designed to be used with a factory organic clutch - the same clutch kit that you would get from any BMW dealer. This makes replacement clutch components easy to source and inexpensive when compared to specialized racing clutches. By using the factory BMW clutch, JB has also made the whole assembly easy to live with when used on the street. The clutch behaves the same as it originally did - just with better throttle response and more power! The JB flywheel can also be rebuilt with a new clutch contact surface - you don't have to buy a new flywheel.

Aluminum flywheels are considered 'single-mass' flywheels because they do not have the same dampening designs as an original 'dual-mass' flywheel. With a single-mass design more noise and vibration may be noticeable. There are steps you can take to minimize the noise - heavier weight transmission oil and clutch discs with anti-rattle springs (sprung-hub clutch).

Stock Flywheel Weight = 40.0lbs
JB Flywheel Weight = 13.0lbs

This item fits the following BMWs:
1999-2003 E39 BMW M5

Show More Show Less

Meistersatz Automatic Transmission Pan Gasket - E34, E36, E39, Z3 ...

T#:19878

Part#: 24111421599

Back Ordered

$ 24.99 USD

Add to Wish List

Qty

$ 24.99 USD

Add to Wish List

GASKET ASBESTOS FREE 24111421599 Manufactured by CRP

JXB Driveshaft Center Support Bearing Carrier Upgrade - BMW E30 3-Ser...

T#:6061699

Part#: BMW09A0

In Stock

Starting at $ 299.99 USD

Add to Wish List

Starting at $ 299.99 USD

Add to Wish List

The stock center support bearing carrier is designed to reduce NVH to the cabin by loosely holding the center bearing with a flimsy rubber bushing. During launches and shifts, the driveshaft is allowed to travel off-center, decreasing throttle response and causing oscillations through the drivetrain. As they age, the carrier rubber sags and dry rots, ruining the driveshaft alignment. Fix or prevent this common issue with JXB Performance's Driveshaft Center Support Bearing Upgrade! JXB utilizes a simple but extremely effective 2-piece design which allows you to install this upgrade and replace bushings with ease. The stock center support carrier is simply cut away, allowing the JXB bushings to "clamp" down on the driveshaft bearing and hold the driveshaft securely in place, maintaining driveshaft alignment at all times. Two bushing options are available for this kit, Street and Track, both of which are many times better than the stock bushings: The street bushings absorb most of the NVH from the drivetrain. Some light NVH is possible at some speeds in the form of a soft hum. (With a modified exhaust or windows down, you’ll probably never hear it) The track bushings are for those who want no-compromise drivetrain performance. These may create a substantial amount of cabin noise. Not sure which is for you? Try them both, they’re interchangeable! Installation does not require the removal of the driveshaft. The 2-part design clamps around the OEM bearing. The old carrier must be removed, so a cutting tool is required. Looking for replacement or additional bushings? See T#4799658 for replacement street bushings and T#4799659 for replacement track bushings.

Show More Show Less

Fall-Line Motorsports - Aluminum DCT Hydraulics Cover - Multiple BMW ...

T#:5498480

Part#: FLM-DCT-HC

In Stock

$ 899.99

This product was last offered at the strikethrough price on
06-01-2026

$ 845.99 USD

Limited Qty Sale

Add to Wish List

Qty

$ 899.99

This product was last offered at the strikethrough price on
06-01-2026

$ 845.99 USD

Limited Qty Sale

Add to Wish List

Like the DCT oil pan, the plastic OEM hydraulics cover is prone to fatiguing from heat cycling; not ideal considering the important parts that reside behind it. And also like it's oil pan sibling, the Fall-Line hydraulics cover uses a bespoke Viton O-Ring that resides within a clever internal channel. Viton O-Rings, due to their exceptional resistance to temperature extremes (-20°F to 400°F operating temp) and low gas permeability, have incredible aging characteristics and therefore eliminate the need for regular replacement.

Show More Show Less

2002, 2002Tii JB Racing Lightweight Aluminum Flywheel 228mm

T#:3762

Part#: 520-100-228

In Stock

$ 581.00 USD

Add to Wish List

Qty

$ 581.00 USD

Add to Wish List

Aluminum flywheels are much lighter than the stock steel flywheel and that produces better throttle response and more available horsepower to the wheels for faster acceleration. The JB Racing aluminum flywheels are a direct replacement for the stock flywheel and work with stock clutch components for an easy upgrade with very little downside.

Modern flywheels are built with additional components and features that are designed to dampen and minimize vibrations from the engine and transmission. As a result they have become bloated in weight and that means more energy is used up just making the flywheel spin. The weight difference between an aluminum and steel flywheel is huge - sometimes more than 50% less. Without the additional mass, more energy can be diverted to where it counts most - moving the car. The flywheel and clutch is one of the first areas that engine builders address when making the rotating assembly lighter for race engines. The dampening effect is just not needed on cars that are focused on performance.

In addition to releasing more power to the wheels, the lighter flywheel allows the engine to spin more freely, which improves throttle response. Again, the difference is huge as you watch the revs build faster than before. With the engine spinning easier the power band comes up much sooner. The stock steel flywheel feels lazy in comparison. There is a driving adjustment required to get used to how much faster the engine revs but that's not really a downside.

The JB lightweight flywheel is designed to be used with a factory organic clutch - the same clutch kit that you would get from any BMW dealer. This makes replacement clutch components easy to source and inexpensive when compared to specialized racing clutches. By using the factory BMW clutch, JB has also made the whole assembly easy to live with when used on the street. The clutch behaves the same as it originally did - just with better throttle response and more power! The JB flywheel can be rebuilt too with a new clutch contact surface.

Aluminum flywheels are considered 'single-mass' flywheels because they do not have the same dampening designs as an original 'dual-mass' flywheel. With a single-mass design more noise and vibration may be noticeable. There are steps you can take to minimize the noise - heavier weight transmission oil and clutch discs with anti-rattle springs (sprung-hub clutch).

Stock Flywheel Weight = 16.5
JB Flywheel Weight = 8lbs

This item fits the following BMWs:
1968-1973 2002 BMW 2002 2002tii

Show More Show Less

BMW E36 328i, Z3 2.8 JB Racing Lightweight Aluminum Flywheel ...

T#:3774

Part#: 520-030-240

In Stock

$ 714.00

This product was last offered at the strikethrough price on
06-08-2026

$ 652.99 USD

Limited Qty Sale

Add to Wish List

Qty

$ 714.00

This product was last offered at the strikethrough price on
06-08-2026

$ 652.99 USD

Limited Qty Sale

Add to Wish List

BMW E36 328i, Z3 2.8 JB Racing Lightweight Aluminum Flywheel offers a significant performance upgrade by replacing the heavy stock steel flywheel with a much lighter aluminum version. This JB Racing flywheel is designed to deliver faster acceleration, improved throttle response, and enhanced overall performance for your BMW.

The modern stock flywheels are burdened with additional components meant to dampen vibrations, which unfortunately adds unnecessary weight. The JB Racing aluminum flywheel, weighing just 10.0 lbs compared to the stock 25.0 lbs, eliminates this excess mass, allowing more power to reach the wheels and reducing the energy wasted on spinning the flywheel. Engine builders prioritize lightweight flywheels when optimizing race engines for maximum efficiency, and the difference is especially noticeable in how quickly the engine revs and reaches its power band.

This JB Racing lightweight flywheel is a direct replacement for the stock flywheel and is compatible with the factory BMW organic clutch. This compatibility ensures that you can use standard replacement clutches, making maintenance simple and cost-effective. The flywheel can also be resurfaced for a fresh contact surface, so there’s no need to buy a new one when it’s time to replace the clutch.

While single-mass aluminum flywheels like this one may result in slightly more noise and vibration compared to dual-mass designs, this can be managed with heavier transmission oil and sprung hub clutches, such as the Sachs Performance clutch available through Turner Motorsport.

Faster acceleration: Reduces the rotational mass for quicker engine response.
Improved throttle response: Engine revs more freely and builds RPM faster.
Enhanced performance: More power delivered to the wheels for better driving dynamics.
Cost-effective maintenance: Compatible with factory BMW organic clutches and can be resurfaced.
Direct replacement: Easy upgrade with no modifications required.

Vehicle Compatibility:

1996-1999 E36 BMW 328i, 328is, 328ic
1997-1998 Z3 BMW Z3 2.8

Show More Show Less

JXB Driveshaft Center Support Bearing Carrier Upgrade

T#:25540331

Part#: 4488208PDKVXXZYU

In Stock

$ 299.99 USD

Add to Wish List

Qty

$ 299.99 USD

Add to Wish List

JXB Driveshaft Center Support Bearing Carrier Upgrade - BMW F10 M5, F...

T#:6061697

Part#: BMW08A0

In Stock

Sale - Save 19% $ 299.99

This product was last offered at the strikethrough price on
05-15-2026

Starting at $ 242.84 USD

Add to Wish List

Sale - Save 19%

$ 299.99

This product was last offered at the strikethrough price on
05-15-2026

Starting at $ 242.84 USD

Add to Wish List

The stock center support bearing carrier is designed to reduce NVH to the cabin by loosely holding the center bearing with a flimsy rubber bushing. During launches and shifts, the driveshaft is allowed to travel off-center, decreasing throttle response and causing oscillations through the drivetrain. As they age, the carrier rubber sags and dry rots, ruining the driveshaft alignment. Fix or prevent this common issue with JXB Performance's Driveshaft Center Support Bearing Upgrade! JXB utilizes a simple but extremely effective 2-piece design which allows you to install this upgrade and replace bushings with ease. The stock center support carrier is simply cut away, allowing the JXB bushings to "clamp" down on the driveshaft bearing and hold the driveshaft securely in place, maintaining driveshaft alignment at all times. Two bushing options are available for this kit, Street and Track, both of which are many times better than the stock bushings: The street bushings absorb most of the NVH from the drivetrain. Some light NVH is possible at some speeds in the form of a soft hum. (With a modified exhaust or windows down, you’ll probably never hear it) The track bushings are for those who want no-compromise drivetrain performance. These may create a substantial amount of cabin noise. Not sure which is for you? Try them both, they’re interchangeable! Installation does not require the removal of the driveshaft. The 2-part design clamps around the OEM bearing. The old carrier must be removed, so a cutting tool is required. Looking for replacement or additional bushings? See T#4799658 for replacement street bushings and T#4799659 for replacement track bushings.

Show More Show Less

E30 325e JB Racing Lightweight Aluminum Flywheel (Replaces Single-Mas...

T#:3763

Part#: 520-070-228

Ships in 5 Business Days

$ 630.00 USD

Add to Wish List

Qty

$ 630.00 USD

Add to Wish List

Aluminum flywheels are much lighter than the stock steel flywheel and that produces better throttle response and more available horsepower to the wheels for faster acceleration. The JB Racing aluminum flywheels are a direct replacement for the stock flywheel and work with stock clutch components for an easy upgrade with very little downside.

Modern flywheels are built with additional components and features that are designed to dampen and minimize vibrations from the engine and transmission. As a result they have become bloated in weight and that means more energy is used up just making the flywheel spin. The weight difference between an aluminum and steel flywheel is huge - sometimes more than 50% less. Without the additional mass, more energy can be diverted to where it counts most - moving the car. The flywheel and clutch is one of the first areas that engine builders address when making the rotating assembly lighter for race engines. The dampening effect is just not needed on cars that are focused on performance.

In addition to releasing more power to the wheels, the lighter flywheel allows the engine to spin more freely, which improves throttle response. Again, the difference is huge as you watch the revs build faster than before. With the engine spinning easier the power band comes up much sooner. The stock steel flywheel feels lazy in comparison. There is a driving adjustment required to get used to how much faster the engine revs but that's not really a downside.

The JB lightweight flywheel is designed to be used with a factory organic clutch - the same clutch kit that you would get from any BMW dealer. This makes replacement clutch components easy to source and inexpensive when compared to specialized racing clutches. By using the factory BMW clutch, JB has also made the whole assembly easy to live with when used on the street. The clutch behaves the same as it originally did - just with better throttle response and more power! The JB flywheel can also be rebuilt with a new clutch contact surface - you don't have to buy a new flywheel.

Aluminum flywheels are considered 'single-mass' flywheels because they do not have the same dampening designs as an original 'dual-mass' flywheel. With a single-mass design more noise and vibration may be noticeable. There are steps you can take to minimize the noise - heavier weight transmission oil and clutch discs with anti-rattle springs (sprung-hub clutch).

The JB flywheel includes ignition trigger wheel.

This flywheel replaces the stock original single-mass flywheel and should only be used with the corresponding 'single-mass' clutch kit. According to BMW the single mass flywheel was installed in all 325e up to 5/86 production date but we have seen some later cars with a single-mass flywheel. The age of the car almost guarantees one or more clutch replacements and possibly a change to the original flywheel as well. You may not know which flywheel is currently installed until the flywheel cover or the transmission is removed.

Stock Flywheel Weight = 24.0lbs
JB Flywheel Weight = 8.5lbs

This item fits the following BMWs:
1984-1988 E30 BMW 325e 325es (with single mass flywheel)

Show More Show Less

Automatic Transmission Oil Pan With Transmission Filter

T#:639811

Part#: 24152333907

Ships in 3 Business Days

$ 155.99 USD

Add to Wish List

Qty

$ 155.99 USD

Add to Wish List

Automatic Transmission Filter & Oil Pan

T#:379609

Part#: 24152333903

Ships in 3 Business Days

$ 139.99 USD

Add to Wish List

Qty

$ 139.99 USD

Add to Wish List

E36, E46 JB Racing Ultra-Light Racing Clutch/Flywheel Assembly ...

T#:340509

Part#: WCCLUTCH

Ships in 5 Business Days

Starting at $ 1,999.00 USD

Add to Wish List

Starting at $ 1,999.00 USD

Add to Wish List

The ultimate in a racing flywheel and clutch! This was developed for use in our E36 and E46 World Challenge Touring Cars. The combined weight of the clutch and flywheel is only 11lbs!!!

This multi-disc (2 or 3 disc setups) offer a minimal flywheel mass (enough to include a factory ring gear for the starter) and a small 5.5" clutch assembly rated to 500hp. By saving as much weight as possible less energy is used in simply spinning the flywheel/clutch assembly and that means a lot more power and torque is available at the drive wheels. The flywheel and clutch is one of the first areas that engine builders address when making the rotating assembly lighter for race engines and this is among the most advanced and lightest racing clutch kits available for your BMW race car.

The JB Ultra-Light Performance racing clutch is available in 2-disc or 3-disc setups. We used the 5.5"/140mm size in our Touring Cars but larger sizes are available too. This is a turn-key racing clutch and flywheel kit that you don't have to engineer or spec yourself. This is the same clutch setup we used when winning the 2003 and 2004 Touring Car Championships - the quality and performance is unquestionable. That series also employed standing starts at each race and this clutch setup performed flawlessly with nearly a full season of racing on them before needing a change.

JB Ultra-Light flywheels include:

precision CNC machined aluminum flywheel

zero-balanced up to 10,000 RPM

replaceable hardened steel clutch friction surface

Helicoil threaded inserts

high-strength grade 10.9 hardware

multi-disc racing clutch with Performance racing pressure plate

JB Racing throw-out bearing with custom bobbin
This is a true racing clutch and will not function as a street-able clutch at all. It behaves as an on/off switch with no slippage allowed. Extreme care must be used when driving on to trailers and around the paddock. But when driven correctly the life span of this clutch is amazing - we could get a full season of racing a 300hp M54 from this clutch setup including standing starts at every race! Replacement clutch components and flywheel rebuilding are available.

A properly adjusted clutch stop is required for use with this clutch kit.

Stock Flywheel + Clutch Weight = 45+lbs
JB Ultra-Light Flywheel & Clutch Weight = 11lbs

This item fits the following BMWs:
1992-1999 E36 BMW 325i 325is 328i 328is M3
1999-2006 E46 BMW 323i 323ci 325i 325ci 328i 328ci 330i 330ci (5-speed)
1997-2002 Z3 BMW Z3 2.3 Z3 2.5i Z3 2.8 Z3 3.0i M Roadster M Coupe
2003-2005 E85 BMW Z4 2.5i (5-speed)

Show More Show Less

E30 325e JB Racing Lightweight Aluminum Flywheel (Replaces Dual-Mass ...

T#:3749

Part#: 520-120-228

In Stock

$ 854.00 USD

Add to Wish List

Qty

$ 854.00 USD

Add to Wish List

Aluminum flywheels are much lighter than the stock steel flywheel and that produces better throttle response and more available horsepower to the wheels for faster acceleration. The JB Racing aluminum flywheels are a direct replacement for the stock flywheel and work with stock clutch components for an easy upgrade with very little downside.

Modern flywheels are built with additional components and features that are designed to dampen and minimize vibrations from the engine and transmission. As a result they have become bloated in weight and that means more energy is used up just making the flywheel spin. The weight difference between an aluminum and steel flywheel is huge - sometimes more than 50% less. Without the additional mass, more energy can be diverted to where it counts most - moving the car. The flywheel and clutch is one of the first areas that engine builders address when making the rotating assembly lighter for race engines. The dampening effect is just not needed on cars that are focused on performance.

In addition to releasing more power to the wheels, the lighter flywheel allows the engine to spin more freely, which improves throttle response. Again, the difference is huge as you watch the revs build faster than before. With the engine spinning easier the power band comes up much sooner. The stock steel flywheel feels lazy in comparison. There is a driving adjustment required to get used to how much faster the engine revs but that's not really a downside.

The JB lightweight flywheel is designed to be used with a factory organic clutch - the same clutch kit that you would get from any BMW dealer. This makes replacement clutch components easy to source and inexpensive when compared to specialized racing clutches. By using the factory BMW clutch, JB has also made the whole assembly easy to live with when used on the street. The clutch behaves the same as it originally did - just with better throttle response and more power! The JB flywheel can also be rebuilt with a new clutch contact surface - you don't have to buy a new flywheel.

Aluminum flywheels are considered 'single-mass' flywheels because they do not have the same dampening designs as an original 'dual-mass' flywheel. With a single-mass design more noise and vibration may be noticeable. There are steps you can take to minimize the noise - heavier weight transmission oil and clutch discs with anti-rattle springs (sprung-hub clutch).

The JB flywheel includes ignition trigger wheel.

This flywheel replaces the stock original dual-mass flywheel and should only be used with the corresponding 'dual-mass' clutch kit. According to BMW the dual mass flywheel was installed in all 325/325e from 5/86 on but we have seen some later cars with a single-mass flywheel. The age of the car almost guarantees one or more clutch replacements and possibly a change to the original flywheel as well. You may not know which flywheel is currently installed until the flywheel cover or the transmission is removed.

Stock Flywheel Weight = 27.5lbs
JB Flywheel Weight = 10.0lbs

This item fits the following BMWs:
1984-1988 E30 BMW 325e 325es (with dual mass flywheel)

Show More Show Less

Z4 M HD Clutch and Flywheel Kit

T#:878

Part#: 520-010S-S873G

Ships in 9 Business Days

$ 1,488.61 USD

Add to Wish List

Qty

$ 1,488.61 USD

Add to Wish List

This lightweight aluminum flywheel w/ Heavy Duty "sprung-hub" clutch package is the best-engineered solution for E46 325 and 330 models with the 6-speed transmission, Z4 2.5/3.0, and Z4 M Roadster and M Coupe. Instead of picking a clutch from another car that may or may not work at all, the engineers at JB Racing have taken all of the guess work out of this upgrade and incorporated a Sachs sport sprung-hub clutch with the correct pressure plate and combined it with their most-popular aluminum lightweight flywheel. The Sachs HD clutch disc has a sprung hub to minimize noise and vibration and organic linings to give the feel and engagement of a stock clutch. Mixing and matching of the incorrect clutch, pressure plate, and flywheel components can lead to inconsistent engagement and feel -- why make your clutch feel worse?

In addition, the Sachs HD pressure plate will clamp with greater force -- allowing approximately 350 ft-lbs of torque, which makes it an obvious upgrade from the stock clutch kit. And with the aluminum flywheel weight savings is substantial over the stock dual-mass flywheel - which allows your motor to spool up faster and transmit more HP to the ground.

Because Sachs is an OE supplier to most German cars, replacement parts are just a phone call away. This kit uses the stock throw-out bearing (included in the price).

Z4 M Sport Clutch and Flywheel Applications:
2006-2008 E85 Z4, E86 Z4 Z4 M Roadster, Z4 M Coupe

Show More Show Less

Project Cars

SELECT YOUR BMW

Sub-Categories

BMW Clutch Stop

Benefits:

Select Vehicle

Purpose

Category

Brand

Price

Special Offers

Shipping

Narrow Results