BMW Drivetrain Parts

OEM INA wheel bearing to replace BMW part # 33411090505 and 33411137685. When wheel bearing begin to fail you normally will here a squeaking or grinding noise or sometimes feel a slight amount of vibration in the steering wheel. Be sure to replace these asap to prevent possible damage to the hub or steering issues.

OEM Schaeffler (INA, LuK, & FAG) is an engineering company that focuses on high-performance, precision manufacturing. With their individual brands INA, Luk, and FAG providing exceptionally high quality parts directly to BMW, as well as countless other automotive companies, their history of reliability and variety of offered parts makes Schaeffler a go-to replacement parts provider for all of us here at Turner Motorsport.

As a leading source of high performance BMW parts and accessories since 1993, we at Turner Motorsport are honored to be the go-to supplier for tens of thousands of enthusiasts the world over. With over two decades of parts, service, and racing experience under our belt, we provide only quality performance and replacement parts.  All of our performance parts are those we would (and do!) install and run on our own cars, as well as replacement parts that are Genuine BMW or from OEM manufacturers. We only offer parts we know you can trust to perform!

This is a replacement rear wheel bearing for all:
1992-1998 E36 BMW M3
1999-2005 E46 BMW 325xi 330i 330ci 330xi M3
1995-2001 E38 BMW 740i 740il 750il
2004-2010 E83 BMW X3 2.5i X3 3.0i X3 3.0si
1997-2002 Z3 BMW M Roadster M Coupe
2003-2008 E85 BMW Z4 M Roadster M Coupe
2000-2003 E52 BMW Z8 Roadster


Rear wheel bearings are sold individually, and 2 are required per car.

When wheel bearing begin to fail you normally will here a squeaking or grinding noise or sometimes feel a slight amount of vibration in the steering wheel. Be sure to replace these asap to prevent possible damage to the hub or steering issues.

OEM Schaeffler (INA, LuK, & FAG) is an engineering company that focuses on high-performance, precision manufacturing. With their individual brands INA, Luk, and FAG providing exceptionally high quality parts directly to BMW, as well as countless other automotive companies, their history of reliability and variety of offered parts makes Schaeffler a go-to replacement parts provider for all of us here at Turner Motorsport.

As a leading source of high performance BMW parts and accessories since 1993, we at Turner Motorsport are honored to be the go-to supplier for tens of thousands of enthusiasts the world over. With over two decades of parts, service, and racing experience under our belt, we provide only quality performance and replacement parts. �All of our performance parts are those we would (and do!) install and run on our own cars, as well as replacement parts that are Genuine BMW or from OEM manufacturers. We only offer parts we know you can trust to perform!

E46 M3, Z4 M Front Wheel Hub Assembly with Bearing. This is an OEM Wheel Bearing Hub Assembly made by FAG and meets all of the OE specifications for fitment and life. FAG is an OE supplier to BMW as well as several other German marques. (SKF does not have a front bearing assembly for the E46 M3).

When wheel bearing begin to fail you normally will here a squeaking or grinding noise or sometimes feel a slight amount of vibration in the steering wheel. Be sure to replace these asap to prevent possible damage to the hub or steering issues.

OEM Schaeffler (INA, LuK, & FAG) is an engineering company that focuses on high-performance, precision manufacturing. With their individual brands INA, Luk, and FAG providing exceptionally high quality parts directly to BMW, as well as countless other automotive companies, their history of reliability and variety of offered parts makes Schaeffler a go-to replacement parts provider for all of us here at Turner Motorsport.

As a leading source of high performance BMW parts and accessories since 1993, we at Turner Motorsport are honored to be the go-to supplier for tens of thousands of enthusiasts the world over. With over two decades of parts, service, and racing experience under our belt, we provide only quality performance and replacement parts.  All of our performance parts are those we would (and do!) install and run on our own cars, as well as replacement parts that are Genuine BMW or from OEM manufacturers. We only offer parts we know you can trust to perform!

BMW E36 E46 E30 Universal Flex Disc is an essential component located between the driveshaft and the transmission, designed to absorb hard vibrations and shocks during gear shifts. Over time, the rubber in the flex disc can degrade, leading to increased vibrations and clunking noises. Replacing this disc ensures your BMW drives smoothly and maintains optimal performance. Turner Motorsport offers this high-quality replacement part, manufactured by URO Parts, a leading provider of direct replacement components. URO Parts adheres to ISO 9000 certification standards, guaranteeing long-lasting durability and reliable performance.

• Absorbs vibrations and shocks from gear shifts
• Reduces clunking noises and enhances driving comfort
• Ensures smooth and optimal vehicle performance
• High-quality construction by URO Parts
• ISO 9000 certified for durability and reliability

YCW Engineering introduces their 100% dry carbon fiber driveshafts for BMW, setting a new standard in performance drivetrain solutions. Constructed entirely of dry carbon fiber with forged 6061 aluminum ends, these driveshafts are significantly lighter than the OEM steel, weighing in at only 11 lbs. This reduction in weight allows for smoother power transfer to the rear differential, enhancing the driving experience.

With over 15 years of experience in the performance driveline field, YCW Engineering has quickly emerged as a leading manufacturer. Their commitment to quality and customer satisfaction is evident in every product, from carbon driveshafts to coilovers and sport axles.

• Lightweight Construction: Made from 100% dry carbon fiber, reducing weight to just 11 lbs.
• Enhanced Power Transfer: Smoother power transfer to the rear differential for improved driving feel.
• Precision Engineering: Balanced to 12,000 RPM and machined to within 0.02mm of OEM tolerances.
• High Torque Capacity: Stress tested to withstand over 4000 lb-ft of torque.
• Quality Assurance: Crafted with over 15 years of performance driveline experience.

Upgrade your BMW with YCW Engineering's dry carbon fiber driveshafts for superior performance and reliability.

Working in collaboration with Competition Clutch, the up and coming German automotive performance company DKM has released a new line of high quality clutches made to satisfy your stock and modified performance needs! If you're having problems keeping power to the wheels, DKM has the solution. Their design, using high-grade materials, gives you increased strength and heat tolerance preventing wear and fade, ensuring increased torque capacity, quicker shifts, and longer clutch life.

Tracking your vehicle is all fun and games until you start burning through clutches as fast as you can afford to replace them. To end this cycle, the MS Twin Disc Clutch Kit is designed to hold up to 100 to 200% more torque capacity and provide you with a much-improved clutch life span. The two organic disc setup provides additional contact surface areas to more evenly distribute pressure and heat for both a boost in performance and wear prevention.

Kit Contents:
Pressure Plate
Two Organic Discs
Steel Single Mass Flywheel
Pilot Bearing/Bushing and Throw-out Bearing (when applicable)
Alignment Tool

One of the most satisfying upgrades you can make to your BMW is to its factory shifter mechanism. By reducing the shifter's throw, you can give your manual transmission BMW a sportier, more precise feel. However, with so many different "short shift kits" out there, how can you be sure you're making the right decision? With the introduction of the Rogue Engineering OCTANE short shift kit, the choice is now crystal clear!

Rogue Engineering refuses to compromise with "lever substitution" as a method of short shift kit development. Rather than using actual test vehicles for their products, some companies actually dig through OEM factory parts diagrams to determine which factory levers can be substituted with others. This "lever substitution" method of introducing product is unacceptable. These shift kits have been developed and perfected through years of experience in proven short shifter technology, by Co-Founder, Ben Liaw. As longtime BMW enthusiasts know, Ben was single-handedly responsible for introducing and developing the idea of affordable, BMW factory-like, short shift kits for late model BMWs (BL/SS for those young enough to remember!). 

Rogue Engineering idea of a short shift kit is not substituting levers in place of factory ones just because "they fit". Throughout the 80s until recently, BMW was notorious for using only a few specific shifter levers for their manual transmission vehicles. For other companies, making just a few "replacement levers" and offering them in place of those factory part numbers was an easy way of calling it a short shift kit. Unfortunately, for those companies, BMW started using many different part numbers making it more difficult to just "swap in a lever".

Rogue Engineering only develops it's short shift kit with test vehicles in their facility, testing numerous prototypes, offering others to test it before settling on its final design. They feel that this old school, real world testing is the best way when modifying OEM ergonomic, sensory-based controls.

Experience unmatched performance with YCW Engineering's 100% dry carbon fiber driveshafts for your BMW. Crafted with precision from dry carbon fiber and forged 6061 aluminum ends, these driveshafts are remarkably lightweight at just 11lbs, significantly lighter than OEM steel. Enjoy smoother power transfer to the rear differential, enhancing your driving experience.

Key Benefits:

• Lightweight construction improves power transfer
• Precision-balanced design ensures smooth operation
• Machined with precision flanges/joints for optimal fit
• Stress-tested to withstand extreme torque levels

YCW Engineering, a leading manufacturer in performance drivetrain solutions, offers a range of racing drivetrain applications, including bespoke development. With over 15 years of experience in performance driveline products, YCW Engineering prides itself on quality and customer satisfaction. Whether you need carbon driveshafts, coilovers, or sport axles, YCW Engineering has the products to complete your BMW build.

Replacement flex disc (guibo). 135mm diameter. 12mm bolt. Application and transmission specific! See below.

Applications:
2008+ E82 BMW 128i
5/1986-1991 E30 BMW 325e 325es M3 - Manual Transmission 
1987-1991 E30 BMW 325ix - Between Transmission & Transfer Case
1996-1998 E36 BMW 328i 328is 328ic - Manual Transmission only 
1999-2005 E46 BMW 323i 323ci 325i 325ci - Automatic & SMG Transmissions only 
1999-2005 E46 BMW 328i 328ci 330i 330ci - Manual, Auto, and SMG
2006+ E90 BMW 325i 328i 330i - Manual or Automatic Transmission 
2006+ E91 BMW 328i - Manual or Automatic Transmission 
2007+ E92 BMW 328i - Manual or Automatic Transmission 
2007+ E93 BMW 328 - Manual or Automatic Transmission 
1982-1983 E28 BMW 528e - Manual Transmission
5/1986-1988 E28 BMW 528e - Manual Transmission
1982-1988 E28 BMW 533i 535i 535is M5 - Manual Transmission 
1991-1995 E34 BMW 525i - Automatic Transmission
1989-6/1992 E34 BMW 525i - Manual Transmission
1993-1995 E34 BMW 530i - Manual or Automatic Transmission
1989-1993 E34 BMW 535i - Manual Transmission
2001-2003 E39 BMW 525i - Automatic Transmission
1997-2003 E39 BMW 528i 530i - Manual or Automatic Transmission 
1980-1989 E24 BMW 633csi 635csi M6 - Manual Transmission
2000-2006 E53 BMW X5 3.0i - for Rear Driveshaft
2000-2003 E53 BMW X5 4.4i X5 4.6is - for Rear Driveshaft
2007-2013 E70 BMW X5 3.0si X5 4.8i X5 xDrive30i X5 xDrive48i - for Rear Driveshaft 
1997-2002 Z3 BMW Z3 2.3 Z3 2.5i - Automatic Transmission 
1997-2002 Z3 BMW Z3 2.8 Z3 3.0i - Manual or Automatic Transmission 
2003-2008 Z4 BMW Z4 2.5i - Automatic or SMG Transmission
2003-2008 Z4 BMW Z4 3.0i Z4 3.0si 

Replacement Front Wheel Bearing for E90 E92 E60 E53 X5 with All wheel Drive models. You will need to replace the locking nut as it cannot be re-used. Typically, the circlip can be re-used but we offer it in case you would like to replace it. When wheel bearing begin to fail you normally will here a squeaking or grinding noise or sometimes feel a slight amount of vibration in the steering wheel. Be sure to replace these asap to prevent possible damage to the hub or steering issues.

OEM Schaeffler (INA, LuK, & FAG) is an engineering company that focuses on high-performance, precision manufacturing. With their individual brands INA, Luk, and FAG providing exceptionally high quality parts directly to BMW, as well as countless other automotive companies, their history of reliability and variety of offered parts makes Schaeffler a go-to replacement parts provider for all of us here at Turner Motorsport.

As a leading source of high performance BMW parts and accessories since 1993, we at Turner Motorsport are honored to be the go-to supplier for tens of thousands of enthusiasts the world over. With over two decades of parts, service, and racing experience under our belt, we provide only quality performance and replacement parts.  All of our performance parts are those we would (and do!) install and run on our own cars, as well as replacement parts that are Genuine BMW or from OEM manufacturers. We only offer parts we know you can trust to perform!

This item fits the following BMWs:
2006+ E90 BMW 325xi 328xi 328i xDrive 330xi 335xi 335i xDrive
2007+ E92 BMW 328xi 328i xDrive 335xi 335i xDrive
2004-2010 E60 BMW 525xi 530xi 528xi 528i xDrive 535xi 535i xDrive
2000-2006 E53 BMW X5 3.0i X5 4.4i X5 4.6is X5 4.8is