BMW Drivetrain Parts

E36 M3, MZ3 JB Racing Lightweight Aluminum Flywheel

T#:3771

Part#: 520-010-240

Ships in 9 Business Days

$ 602.00 USD

Add to Wish List

Qty

$ 602.00 USD

Add to Wish List

Aluminum flywheels are much lighter than the stock steel flywheel and that produces better throttle response and more available horsepower to the wheels for faster acceleration. The JB Racing aluminum flywheels are a direct replacement for the stock flywheel and work with stock clutch components for an easy upgrade with very little downside.

Modern flywheels are built with additional components and features that are designed to dampen and minimize vibrations from the engine and transmission. As a result they have become bloated in weight and that means more energy is used up just making the flywheel spin. The weight difference between an aluminum and steel flywheel is huge - sometimes more than 50% less. Without the additional mass, more energy can be diverted to where it counts most - moving the car. The flywheel and clutch is one of the first areas that engine builders address when making the rotating assembly lighter for race engines. The dampening effect is just not needed on cars that are focused on performance.

In addition to releasing more power to the wheels, the lighter flywheel allows the engine to spin more freely, which improves throttle response. Again, the difference is huge as you watch the revs build faster than before. With the engine spinning easier the power band comes up much sooner. The stock steel flywheel feels lazy in comparison. There is a driving adjustment required to get used to how much faster the engine revs but that's not really a downside.

The JB lightweight flywheel is designed to be used with a factory organic clutch - the same clutch kit that you would get from any BMW dealer. This makes replacement clutch components easy to source and inexpensive when compared to specialized racing clutches. By using the factory BMW clutch, JB has also made the whole assembly easy to live with when used on the street. The clutch behaves the same as it originally did - just with better throttle response and more power! The JB flywheel can also be rebuilt with a new clutch contact surface - you don't have to buy a new flywheel.

Aluminum flywheels are considered 'single-mass' flywheels because they do not have the same dampening designs as an original 'dual-mass' flywheel. With a single-mass design more noise and vibration may be noticeable. There are steps you can take to minimize the noise - heavier weight transmission oil and clutch discs with anti-rattle springs (sprung-hub clutch). In addition to the standard replacement clutches, we also sell Sachs Performance sprung hub clutches that also work with the JB flywheels.

Stock Flywheel Weight = 25.5lbs
JB Flywheel Weight = 10.0lbs

This item fits the following BMWs:
1995-1999 E36 BMW M3
1998-2002 Z3 BMW Z3 M Roadster M Coupe

Show More Show Less

VTT F9X X3/4M Rear Bushing Insert Kit

T#:26404885

Part#: VTT-X3M-REAR-IN1

Ships in 1-2 days

$ 139.99 USD

Add to Wish List

Qty

$ 139.99 USD

Add to Wish List

N54/N55 BMW Automatic Transmission Cooler - E9X 335

T#:1347205

Part#: N54N55TRANSCOOL

In Stock

$ 444.99

This product was last offered at the strikethrough price on
06-16-2026

$ 399.00 USD

Add to Wish List

Qty

$ 399.00 USD

Add to Wish List

Everyone knows that heat is the enemy of your automatic transmission. And everyone knows that higher power levels generate more transmission fluid heat. Now you can extend the life of your automatic transmission by installing the new Burger Motorsports High Capacity Trans Cooler kit. This unique plug-and-play kit replaces your factory coolant to trans fluid heat exchanger with a high-capacity fender-mounted air-to-trans fluid radiator. Includes all mounting hardware, lines, and coolant caps required for installation. Installs inside the driverside fender providing ample airflow over the large cooling core via existing openings. The result is dramatically reduced transmission temperature and extended transmission life. This kit is strongly suggested for any BMW E chassis automatic running larger than factory turbos. FEATURES AND BENEFITS Dissipates excess transmission fluid heat Reduces transmission fluid temperature Increases transmission life when racing Increases transmission oil capacity Fitment: 2006-2011 E90 Sedan 335i/335ix 2006-2013 E90 E91 Sedan/Touring 335d (M57 diesel) 2006-2011 E91 Touring 335i/335ix 2011-2013 E92 Coupe 335is 2007-2013 E92 Coupe 335i/335ix 2006-2013 E93 Convertible 335i/335ix Compatible with both RHD and LHD vehicles. Not compatible with manual transmissions.

Show More Show Less

Condor Speed Shop G260 Transmission Brace for 24v Swaps - E30 BMW ...

T#:577863

Part#: G260TBRACE

Ships in 1 Business Day

$ 75.00 USD

Add to Wish List

Qty

$ 75.00 USD

Add to Wish List

Ultra-light aluminum G260 transmission brace for 24V engine swaps. This brace must be used if swapping a 24v motor into an e30, with the original G260 transmission. *Please note you will need to bend/twist the selector rod to get your shift lever in the correct orientation.

Show More Show Less

E30 318i/is, E36 318i, Z3 1.9 JB Racing Lightweight Aluminum Flywheel...

T#:3769

Part#: 520-040-215

Back Ordered

11% off MSRP $ 765.00

MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.

$ 679.00 USD

Add to Wish List

Qty

11% off MSRP

$ 765.00

MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.

$ 679.00 USD

Add to Wish List

Aluminum flywheels are much lighter than the stock steel flywheel and that produces better throttle response and more available horsepower to the wheels for faster acceleration. The JB Racing aluminum flywheels are a direct replacement for the stock flywheel and work with stock clutch components for an easy upgrade with very little downside.

Modern flywheels are built with additional components and features that are designed to dampen and minimize vibrations from the engine and transmission. As a result they have become bloated in weight and that means more energy is used up just making the flywheel spin. The weight difference between an aluminum and steel flywheel is huge - sometimes more than 50% less. Without the additional mass, more energy can be diverted to where it counts most - moving the car. The flywheel and clutch is one of the first areas that engine builders address when making the rotating assembly lighter for race engines. The dampening effect is just not needed on cars that are focused on performance.

In addition to releasing more power to the wheels, the lighter flywheel allows the engine to spin more freely, which improves throttle response. Again, the difference is huge as you watch the revs build faster than before. With the engine spinning easier the power band comes up much sooner. The stock steel flywheel feels lazy in comparison. There is a driving adjustment required to get used to how much faster the engine revs but that's not really a downside.

The JB lightweight flywheel is designed to be used with a factory organic clutch - the same clutch kit that you would get from any BMW dealer. This makes replacement clutch components easy to source and inexpensive when compared to specialized racing clutches. By using the factory BMW clutch, JB has also made the whole assembly easy to live with when used on the street. The clutch behaves the same as it originally did - just with better throttle response and more power! The JB flywheel can also be rebuilt with a new clutch contact surface - you don't have to buy a new flywheel.

Aluminum flywheels are considered 'single-mass' flywheels because they do not have the same dampening designs as an original 'dual-mass' flywheel. With a single-mass design more noise and vibration may be noticeable. There are steps you can take to minimize the noise - heavier weight transmission oil and clutch discs with anti-rattle springs (sprung-hub clutch).

Stock Flywheel Weight = 27.0lbs
JB Flywheel Weight = 9.0lbs

This item fits the following BMWs:
1989-1992 E30 BMW 318i 318is 318ic
1992-1997 E36 BMW 318i 318is 318ti 318ic
1996-1997 Z3 BMW Z3 1.9

Show More Show Less

E60, E82, E85, E9X, E89 (N52 Engine) JB Racing Lightweight Aluminum F...

T#:2801

Part#: 520-200-240

In Stock

$ 714.00 USD

Add to Wish List

Qty

$ 714.00 USD

Add to Wish List

Aluminum flywheels are much lighter than the stock steel flywheel and that produces better throttle response and more available horsepower to the wheels for faster acceleration. The JB Racing aluminum flywheels are a direct replacement for the stock flywheel and work with stock clutch components for an easy upgrade with very little downside.

Modern flywheels are built with additional components and features that are designed to dampen and minimize vibrations from the engine and transmission. As a result they have become bloated in weight and that means more energy is used up just making the flywheel spin. The weight difference between an aluminum and steel flywheel is huge - sometimes more than 50% less. Without the additional mass, more energy can be diverted to where it counts most - moving the car. The flywheel and clutch is one of the first areas that engine builders address when making the rotating assembly lighter for race engines. The dampening effect is just not needed on cars that are focused on performance.

In addition to releasing more power to the wheels, the lighter flywheel allows the engine to spin more freely, which improves throttle response. Again, the difference is huge as you watch the revs build faster than before. With the engine spinning easier the power band comes up much sooner. The stock steel flywheel feels lazy in comparison. There is a driving adjustment required to get used to how much faster the engine revs but that's not really a downside.

The JB lightweight flywheel is designed to be used with a factory organic clutch - the same clutch kit that you would get from any BMW dealer. This makes replacement clutch components easy to source and inexpensive when compared to specialized racing clutches. By using the factory BMW clutch, JB has also made the whole assembly easy to live with when used on the street. The clutch behaves the same as it originally did - just with better throttle response and more power! The JB flywheel can also be rebuilt with a new clutch contact surface - you don't have to buy a new flywheel.

Aluminum flywheels are considered 'single-mass' flywheels because they do not have the same dampening designs as an original 'dual-mass' flywheel. With a single-mass design more noise and vibration may be noticeable. There are steps you can take to minimize the noise - heavier weight transmission oil and clutch discs with anti-rattle springs (sprung-hub clutch).

This JB flywheel replaces the stock flywheel and can be used with either the stock 228mm or stock 240mm clutch discs. Depending on the model you may have either clutch size in your car but this flywheel is compatible with both. You can install a 240mm clutch as a mild upgrade.

Stock Flywheel Weight = 24-31.0lbs
JB Flywheel Weight = 12.0lbs

This item fits the following BMWs:
2006-2010 E60 BMW - 525i, 528i, 530i
2006-2013 E90, E91, E92, E93 BMW - 325i, 328i, 330i
2007-2013 E82 BMW - 125i, 128i
2006-2008 E85, E86 BMW - Z4 3.0i, Z4 3.0si
2009-later E89 BMW - Z4 3.0i

Show More Show Less

E46 M3 6MT JB Racing Lightweight Aluminum Flywheel

T#:302739

Part#: 520-180-240

Ships in 8 Business Days

$ 602.00 USD

Add to Wish List

Qty

$ 602.00 USD

Add to Wish List

Aluminum flywheels are much lighter than the stock steel flywheel and that produces better throttle response and more available horsepower to the wheels for faster acceleration. The JB Racing aluminum flywheels are a direct replacement for the stock flywheel and work with stock clutch components for an easy upgrade with very little downside.

Modern flywheels are built with additional components and features that are designed to dampen and minimize vibrations from the engine and transmission. As a result they have become bloated in weight and that means more energy is used up just making the flywheel spin. The weight difference between an aluminum and steel flywheel is huge - sometimes more than 50% less. Without the additional mass, more energy can be diverted to where it counts most - moving the car. The flywheel and clutch is one of the first areas that engine builders address when making the rotating assembly lighter for race engines. The dampening effect is just not needed on cars that are focused on performance.

In addition to releasing more power to the wheels, the lighter flywheel allows the engine to spin more freely, which improves throttle response. Again, the difference is huge as you watch the revs build faster than before. With the engine spinning easier the power band comes up much sooner. The stock steel flywheel feels lazy in comparison. There is a driving adjustment required to get used to how much faster the engine revs but that's not really a downside.

The JB lightweight flywheel is designed to be used with a factory organic clutch - the same clutch kit that you would get from any BMW dealer. This makes replacement clutch components easy to source and inexpensive when compared to specialized racing clutches. By using the factory BMW clutch, JB has also made the whole assembly easy to live with when used on the street. The clutch behaves the same as it originally did - just with better throttle response and more power! The JB flywheel can also be rebuilt with a new clutch contact surface - you don't have to buy a new flywheel.

Aluminum flywheels are considered 'single-mass' flywheels because they do not have the same dampening designs as an original 'dual-mass' flywheel. With a single-mass design more noise and vibration may be noticeable. There are steps you can take to minimize the noise - heavier weight transmission oil and clutch discs with anti-rattle springs (sprung-hub clutch). In addition to the standard replacement clutches, we also sell Sachs Performance sprung hub clutches that also work with the JB flywheels.

Stock Flywheel Weight = 25.0lbs
JB Flywheel Weight = 10.0lbs

This item fits the following BMWs:
2001-2006 E46 BMW M3 (6-speed manual only, not for SMG)

Show More Show Less

Burger Motorsports Differential Support Bracket Brace - F-Chassis BMW...

T#:637547

Part#: BMS-DSBB-F

Back Ordered

Starting at $ 129.00 USD

Add to Wish List

Starting at $ 129.00 USD

Add to Wish List

The BMS differential brace attaches the rear differential to the subframe allowing better launches, less wheel hop, and a more stable feeling rear chassis. Their unique one-piece construction eliminates welding weak points common on similar units. No logos or markings are visible for a stealth OEM appearance.

Show More Show Less

E46 323/325/328/330 5-speed, Z3 2.3/2.8/3.0 JB Racing Lightweight Alu...

T#:4227

Part#: 520-140-240

In Stock

$ 602.00 USD

Add to Wish List

Qty

$ 602.00 USD

Add to Wish List

Aluminum flywheels are much lighter than the stock steel flywheel and that produces better throttle response and more available horsepower to the wheels for faster acceleration. The JB Racing aluminum flywheels are a direct replacement for the stock flywheel and work with stock clutch components for an easy upgrade with very little downside.

Modern flywheels are built with additional components and features that are designed to dampen and minimize vibrations from the engine and transmission. As a result they have become bloated in weight and that means more energy is used up just making the flywheel spin. The weight difference between an aluminum and steel flywheel is huge - sometimes more than 50% less. Without the additional mass, more energy can be diverted to where it counts most - moving the car. The flywheel and clutch is one of the first areas that engine builders address when making the rotating assembly lighter for race engines. The dampening effect is just not needed on cars that are focused on performance.

In addition to releasing more power to the wheels, the lighter flywheel allows the engine to spin more freely, which improves throttle response. Again, the difference is huge as you watch the revs build faster than before. With the engine spinning easier the power band comes up much sooner. The stock steel flywheel feels lazy in comparison. There is a driving adjustment required to get used to how much faster the engine revs but that's not really a downside.

The JB lightweight flywheel is designed to be used with a factory organic clutch - the same clutch kit that you would get from any BMW dealer. This makes replacement clutch components easy to source and inexpensive when compared to specialized racing clutches. By using the factory BMW clutch, JB has also made the whole assembly easy to live with when used on the street. The clutch behaves the same as it originally did - just with better throttle response and more power! The JB flywheel can also be rebuilt with a new clutch contact surface - you don't have to buy a new flywheel.

Aluminum flywheels are considered 'single-mass' flywheels because they do not have the same dampening designs as an original 'dual-mass' flywheel. With a single-mass design more noise and vibration may be noticeable. There are steps you can take to minimize the noise - heavier weight transmission oil and clutch discs with anti-rattle springs (sprung-hub clutch). In addition to the standard replacement clutches, we also sell Sachs Performance sprung hub clutches that also work with the JB flywheels.

Stock Flywheel Weight = 25.0lbs
JB Flywheel Weight = 10.0lbs

This item fits the following BMWs:
1999-2002 E46 BMW 323i 323ci 325i 325ci 328i 328ci 330i 330ci (with 5-speed manual transmission)
2001-2005 E46 BMW 325xi 330xi
1997-2002 Z3 BMW Z3 2.3 Z3 2.5i Z3 2.8 Z3 3.0i

Show More Show Less

JB Racing Single Mass Lightweight Aluminum Flywheel - 6-speed - E46 3...

T#:3474

Part#: 520-190-240

Ships in 2 Business Days

$ 672.00 USD

Add to Wish List

Qty

$ 672.00 USD

Add to Wish List

This is a performance replacement for BMW Part # 21207533868 Aluminum flywheels are much lighter than the stock steel flywheel and that produces better throttle response and more available horsepower to the wheels for faster acceleration. The JB Racing aluminum flywheels are a direct replacement for the stock flywheel and work with stock clutch components for an easy upgrade with very little downside.

Modern flywheels are built with additional components and features that are designed to dampen and minimize vibrations from the engine and transmission. As a result they have become bloated in weight and that means more energy is used up just making the flywheel spin. The weight difference between an aluminum and steel flywheel is huge - sometimes more than 50% less. Without the additional mass, more energy can be diverted to where it counts most - moving the car. The flywheel and clutch is one of the first areas that engine builders address when making the rotating assembly lighter for race engines. The dampening effect is just not needed on cars that are focused on performance.

In addition to releasing more power to the wheels, the lighter flywheel allows the engine to spin more freely, which improves throttle response. Again, the difference is huge as you watch the revs build faster than before. With the engine spinning easier the power band comes up much sooner. The stock steel flywheel feels lazy in comparison. There is a driving adjustment required to get used to how much faster the engine revs but that's not really a downside.

The JB lightweight flywheel is designed to be used with a factory organic clutch - the same clutch kit that you would get from any BMW dealer. This makes replacement clutch components easy to source and inexpensive when compared to specialized racing clutches. By using the factory BMW clutch, JB has also made the whole assembly easy to live with when used on the street. The clutch behaves the same as it originally did - just with better throttle response and more power! The JB flywheel can also be rebuilt with a new clutch contact surface - you don't have to buy a new flywheel.

Aluminum flywheels are considered 'single-mass' flywheels because they do not have the same dampening designs as an original 'dual-mass' flywheel. With a single-mass design more noise and vibration may be noticeable. There are steps you can take to minimize the noise - heavier weight transmission oil and clutch discs with anti-rattle springs (sprung-hub clutch).

The JB Flywheel includes the pilot bearing mounted in the flywheel hub, just like the factory configuration.

Stock Flywheel Weight = 25.0lbs
JB Flywheel Weight = 10.5lbs

This item fits the following BMWs:
2002-2005 E46 BMW 325i 330i (with 6-speed manual transmission)

Show More Show Less

E30 M3 JB Racing Lightweight Aluminum Flywheel

T#:3768

Part#: 520-050-228

Ships in 4 Business Days

$ 630.00 USD

Add to Wish List

Qty

$ 630.00 USD

Add to Wish List

Aluminum flywheels are much lighter than the stock steel flywheel and that produces better throttle response and more available horsepower to the wheels for faster acceleration. The JB Racing aluminum flywheels are a direct replacement for the stock flywheel and work with stock clutch components for an easy upgrade with very little downside.

Modern flywheels are built with additional components and features that are designed to dampen and minimize vibrations from the engine and transmission. As a result they have become bloated in weight and that means more energy is used up just making the flywheel spin. The weight difference between an aluminum and steel flywheel is huge - sometimes more than 50% less. Without the additional mass, more energy can be diverted to where it counts most - moving the car. The flywheel and clutch is one of the first areas that engine builders address when making the rotating assembly lighter for race engines. The dampening effect is just not needed on cars that are focused on performance.

In addition to releasing more power to the wheels, the lighter flywheel allows the engine to spin more freely, which improves throttle response. Again, the difference is huge as you watch the revs build faster than before. With the engine spinning easier the power band comes up much sooner. The stock steel flywheel feels lazy in comparison. There is a driving adjustment required to get used to how much faster the engine revs but that's not really a downside.

The JB lightweight flywheel is designed to be used with a factory organic clutch - the same clutch kit that you would get from any BMW dealer. This makes replacement clutch components easy to source and inexpensive when compared to specialized racing clutches. By using the factory BMW clutch, JB has also made the whole assembly easy to live with when used on the street. The clutch behaves the same as it originally did - just with better throttle response and more power! The JB flywheel can also be rebuilt with a new clutch contact surface - you don't have to buy a new flywheel.

Aluminum flywheels are considered 'single-mass' flywheels because they do not have the same dampening designs as an original 'dual-mass' flywheel. With a single-mass design more noise and vibration may be noticeable. There are steps you can take to minimize the noise - heavier weight transmission oil and clutch discs with anti-rattle springs (sprung-hub clutch).

The JB flywheel includes ignition trigger wheel.

Stock Flywheel Weight = 19.5lbs
JB Flywheel Weight = 8.0lbs

This item fits the following BMWs:
1987-1991 E30 BMW M3

Show More Show Less

E30 325i, E34 525i (M20) JB Racing Lightweight Aluminum Flywheel (Rep...

T#:385699

Part#: 520-060-228

Ships on Sep 1, 2026

$ 581.00 USD

Add to Wish List

Qty

$ 581.00 USD

Add to Wish List

Aluminum flywheels are much lighter than the stock steel flywheel and that produces better throttle response and more available horsepower to the wheels for faster acceleration. The JB Racing aluminum flywheels are a direct replacement for the stock flywheel and work with stock clutch components for an easy upgrade with very little downside.

Modern flywheels are built with additional components and features that are designed to dampen and minimize vibrations from the engine and transmission. As a result they have become bloated in weight and that means more energy is used up just making the flywheel spin. The weight difference between an aluminum and steel flywheel is huge - sometimes more than 50% less. Without the additional mass, more energy can be diverted to where it counts most - moving the car. The flywheel and clutch is one of the first areas that engine builders address when making the rotating assembly lighter for race engines. The dampening effect is just not needed on cars that are focused on performance.

In addition to releasing more power to the wheels, the lighter flywheel allows the engine to spin more freely, which improves throttle response. Again, the difference is huge as you watch the revs build faster than before. With the engine spinning easier the power band comes up much sooner. The stock steel flywheel feels lazy in comparison. There is a driving adjustment required to get used to how much faster the engine revs but that's not really a downside.

The JB lightweight flywheel is designed to be used with a factory organic clutch - the same clutch kit that you would get from any BMW dealer. This makes replacement clutch components easy to source and inexpensive when compared to specialized racing clutches. By using the factory BMW clutch, JB has also made the whole assembly easy to live with when used on the street. The clutch behaves the same as it originally did - just with better throttle response and more power! The JB flywheel can also be rebuilt with a new clutch contact surface - you don't have to buy a new flywheel.

Aluminum flywheels are considered 'single-mass' flywheels because they do not have the same dampening designs as an original 'dual-mass' flywheel. With a single-mass design more noise and vibration may be noticeable. There are steps you can take to minimize the noise - heavier weight transmission oil and clutch discs with anti-rattle springs (sprung-hub clutch).

This flywheel replaces the stock original single-mass flywheel and should only be used with the corresponding 'single-mass' clutch kit. According to BMW the single mass flywheel was installed in all 325i up to 12/86 production date but we have seen some later cars with a single-mass flywheel. The age of the car almost guarantees one or more clutch replacements and possibly a change to the original flywheel as well. You may not know which flywheel is currently installed until the flywheel cover or the transmission is removed.

Stock Flywheel Weight = 18.0lbs
JB Flywheel Weight = 8.0lbs

This item fits the following BMWs:
1984-1991 E30 BMW 325i 325ic 325is (with single-mass flywheel)
1989-1990 E34 BMW 525i (with single-mass flywheel)

Show More Show Less

Genuine MINI Clutch Release Bearing

T#:49039

Part#: 21517570228

In Stock

8% off MSRP $ 73.99

MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.

$ 67.99 USD

Add to Wish List

Qty

8% off MSRP

$ 73.99

MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.

$ 67.99 USD

Add to Wish List

Genuine MINI CLUTCH RELEASE BEARING

E34 M5 JB Racing Lightweight Aluminum Flywheel

T#:3772

Part#: 520-090-240

Ships in 7 Business Days

$ 581.00 USD

Add to Wish List

Qty

$ 581.00 USD

Add to Wish List

Aluminum flywheels are much lighter than the stock steel flywheel and that produces better throttle response and more available horsepower to the wheels for faster acceleration. The JB Racing aluminum flywheels are a direct replacement for the stock flywheel and work with stock clutch components for an easy upgrade with very little downside.

Modern flywheels are built with additional components and features that are designed to dampen and minimize vibrations from the engine and transmission. As a result they have become bloated in weight and that means more energy is used up just making the flywheel spin. The weight difference between an aluminum and steel flywheel is huge - sometimes more than 50% less. Without the additional mass, more energy can be diverted to where it counts most - moving the car. The flywheel and clutch is one of the first areas that engine builders address when making the rotating assembly lighter for race engines. The dampening effect is just not needed on cars that are focused on performance.

In addition to releasing more power to the wheels, the lighter flywheel allows the engine to spin more freely, which improves throttle response. Again, the difference is huge as you watch the revs build faster than before. With the engine spinning easier the power band comes up much sooner. The stock steel flywheel feels lazy in comparison. There is a driving adjustment required to get used to how much faster the engine revs but that's not really a downside.

The JB lightweight flywheel is designed to be used with a factory organic clutch - the same clutch kit that you would get from any BMW dealer. This makes replacement clutch components easy to source and inexpensive when compared to specialized racing clutches. By using the factory BMW clutch, JB has also made the whole assembly easy to live with when used on the street. The clutch behaves the same as it originally did - just with better throttle response and more power! The JB flywheel can also be rebuilt with a new clutch contact surface - you don't have to buy a new flywheel.

Aluminum flywheels are considered 'single-mass' flywheels because they do not have the same dampening designs as an original 'dual-mass' flywheel. With a single-mass design more noise and vibration may be noticeable.

Stock Flywheel Weight = 16.0lbs
JB Flywheel Weight = 8.0lbs

This item fits the following BMWs:
1991-1995 E34 BMW M5

Show More Show Less

BMW E9X 335i BMS Differential Support Bracket Brace - Small Case ...

T#:1316770

Part#: E9XDIFFBRACE-SM

Back Ordered

$ 99.00 USD

Add to Wish List

Qty

$ 99.00 USD

Add to Wish List

BMW E9X 335i BMS Differential Support Bracket Brace - Small Case

The BMW E9X 335i BMS Differential Support Bracket Brace - Small Case is a high-performance upgrade designed to enhance the stability and durability of the differential mount. Turner Motorsport offers this precision-engineered brace to reduce flex and movement of the differential, ensuring improved power transfer and handling. Ideal for high-performance driving or track use, this brace helps maintain proper alignment and extends the lifespan of your differential components.

Benefits:

Enhances differential stability by reducing flex and movement
Improves power transfer and handling performance
Precision-engineered for a perfect fit and reliable performance
Ideal for high-performance driving and track use
Extends the lifespan of differential components
Made from high-quality materials for durability and strength

Show More Show Less

2002, E21 320i, E30 318i (M10) JB Racing Lightweight Aluminum Flywhee...

T#:3647

Part#: 520-110-215

Ships in 2 Business Days

$ 581.00 USD

Add to Wish List

Qty

$ 581.00 USD

Add to Wish List

Aluminum flywheels are much lighter than the stock steel flywheel and that produces better throttle response and more available horsepower to the wheels for faster acceleration. The JB Racing aluminum flywheels are a direct replacement for the stock flywheel and work with stock clutch components for an easy upgrade with very little downside.

Modern flywheels are built with additional components and features that are designed to dampen and minimize vibrations from the engine and transmission. As a result they have become bloated in weight and that means more energy is used up just making the flywheel spin. The weight difference between an aluminum and steel flywheel is huge - sometimes more than 50% less. Without the additional mass, more energy can be diverted to where it counts most - moving the car. The flywheel and clutch is one of the first areas that engine builders address when making the rotating assembly lighter for race engines. The dampening effect is just not needed on cars that are focused on performance.

In addition to releasing more power to the wheels, the lighter flywheel allows the engine to spin more freely, which improves throttle response. Again, the difference is huge as you watch the revs build faster than before. With the engine spinning easier the power band comes up much sooner. The stock steel flywheel feels lazy in comparison. There is a driving adjustment required to get used to how much faster the engine revs but that's not really a downside.

The JB lightweight flywheel is designed to be used with a factory organic clutch - the same clutch kit that you would get from any BMW dealer. This makes replacement clutch components easy to source and inexpensive when compared to specialized racing clutches. By using the factory BMW clutch, JB has also made the whole assembly easy to live with when used on the street. The clutch behaves the same as it originally did - just with better throttle response and more power! The JB flywheel can be rebuilt too with a new clutch contact surface.

Aluminum flywheels are considered 'single-mass' flywheels because they do not have the same dampening designs as an original 'dual-mass' flywheel. With a single-mass design more noise and vibration may be noticeable. There are steps you can take to minimize the noise - heavier weight transmission oil and clutch discs with anti-rattle springs (sprung-hub clutch).

Stock Flywheel Weight = 16.5lbs
JB Flywheel Weight = 8lbs

This item fits the following BMWs:
1974-1976 2002 BMW 2002
1977-1983 E21 BMW 320i
1984-1985 E30 BMW 318i

Show More Show Less

BMS Differential Support Bracket Brace - BMW 135i / E9x 335i - Large ...

T#:1316771

Part#: E9XDIFFBRACE-LG

Ships in 1 Business Day

$ 99.00 USD

Add to Wish List

Qty

$ 99.00 USD

Add to Wish List

VTT Billet BMW Transfer Case Bushing Inserts - Version A

T#:26404870

Part#: VTT-XFER-CASE-BU

Ships in 10 Business Days

$ 137.99 USD

Add to Wish List

Qty

$ 137.99 USD

Add to Wish List

Soft bushings are the enemy of launching hard, and keeping your drivetrain together. The BMW Transfer Case bushings are notoriously soft, and that is the opposite of what you want when launching a car hard. You can replace the bushing with a solid one, but this is time-consuming usually requires lowering or removing the transfer case, and results in a lot of added NVH. The best path is simply to reduce the amount of flex of the factory bushing so you keep the nice manners when cruising around town, and at idle, but when its time to the launch the transfer case cannot move as it could without the insert. These come as a set of two with 2 bolts to keep them in place. Install time once you get to them is about 2-3 minutes. Could not be easier. Put some lube on them, push them in, and tighten the screws. These are a MUST for high-power G8X, and F9X X3/X4M Builds. All platforms they fit are below. Features: 6061- T6 aluminum construction Easy to install Fully reversible Do not add NVH

Show More Show Less

E39 540i 97-03 JB Racing Lightweight Aluminum Flywheel

T#:1339

Part#: 520-150-240

In Stock

$ 903.00 USD

Add to Wish List

Qty

$ 903.00 USD

Add to Wish List

Aluminum flywheels are much lighter than the stock steel flywheel and that produces better throttle response and more available horsepower to the wheels for faster acceleration. The JB Racing aluminum flywheels are a direct replacement for the stock flywheel and work with stock clutch components for an easy upgrade with very little downside.

Modern flywheels are built with additional components and features that are designed to dampen and minimize vibrations from the engine and transmission. As a result they have become bloated in weight and that means more energy is used up just making the flywheel spin. The weight difference between an aluminum and steel flywheel is huge - sometimes more than 50% less. Without the additional mass, more energy can be diverted to where it counts most - moving the car. The flywheel and clutch is one of the first areas that engine builders address when making the rotating assembly lighter for race engines. The dampening effect is just not needed on cars that are focused on performance.

In addition to releasing more power to the wheels, the lighter flywheel allows the engine to spin more freely, which improves throttle response. Again, the difference is huge as you watch the revs build faster than before. With the engine spinning easier the power band comes up much sooner. The stock steel flywheel feels lazy in comparison. There is a driving adjustment required to get used to how much faster the engine revs but that's not really a downside.

The JB lightweight flywheel is designed to be used with a factory organic clutch - the same clutch kit that you would get from any BMW dealer. This makes replacement clutch components easy to source and inexpensive when compared to specialized racing clutches. By using the factory BMW clutch, JB has also made the whole assembly easy to live with when used on the street. The clutch behaves the same as it originally did - just with better throttle response and more power! The JB flywheel can also be rebuilt with a new clutch contact surface - you don't have to buy a new flywheel.

Aluminum flywheels are considered 'single-mass' flywheels because they do not have the same dampening designs as an original 'dual-mass' flywheel. With a single-mass design more noise and vibration may be noticeable. There are steps you can take to minimize the noise - heavier weight transmission oil and clutch discs with anti-rattle springs (sprung-hub clutch).

Stock Flywheel Weight = 33.0lbs
JB Flywheel Weight = 13.0lbs

This item fits the following BMWs:
1997-2003 E39 BMW 540i

Show More Show Less

VTT F9X X3/4M Front Bushing Inserts

T#:26404887

Part#: VTT-X3M-FR-INS

Back Ordered

$ 104.99 USD

Add to Wish List

Qty

$ 104.99 USD

Add to Wish List

Looking to fix the diff bolt issue on your F9X X3/4M? VTT has taken a 3 pronged approach by offering a triple solution, one part of the solution is the front diff bushing inserts. These are pressed into the factory bushing, and fill the voids in the bushing. This keeps the stock bushing ride compliance but removes any unwanted movement. These are sold as a set Kit includes: Two Billet Bushing inserts Two 46mm Hardened Steel Washers

Show More Show Less

Condor Speed Shop Solid UHMW M20 Motor Mount Set & Transmission Mount...

T#:577859

Part#: M20M_TRANS

Ships in 3 Business Days

$ 79.00 USD

Add to Wish List

Qty

$ 79.00 USD

Add to Wish List

Under hard braking the stock mounts allow the m20 to pitch forward and to the side. These solid UHMW replacement mounts stiffen the engine and drivetrain, dramatically changing the responsiveness of your BMW E30. These solid UHMW motor mounts are a direct replacement for your original 1984-1991 E30 BMW 323, 325e 325es 325i 325ic 325is' OEM rubber motor mounts. UHMW is an excellent general-purpose plastic with a unique combination of wear and corrosion resistance, low friction surface and impact strength. It is resistant to chemical attack and moisture absorption and retains key physical properties to -30 C. Includes solid transmission mounts as well!

Show More Show Less

E24 633/635CSi/M6, E28 535i/M5 JB Racing Lightweight Aluminum Flywhee...

T#:3770

Part#: 520-080-240

Ships in 8 Business Days

$ 630.00 USD

Add to Wish List

Qty

$ 630.00 USD

Add to Wish List

Aluminum flywheels are much lighter than the stock steel flywheel and that produces better throttle response and more available horsepower to the wheels for faster acceleration. The JB Racing aluminum flywheels are a direct replacement for the stock flywheel and work with stock clutch components for an easy upgrade with very little downside.

Modern flywheels are built with additional components and features that are designed to dampen and minimize vibrations from the engine and transmission. As a result they have become bloated in weight and that means more energy is used up just making the flywheel spin. The weight difference between an aluminum and steel flywheel is huge - sometimes more than 50% less. Without the additional mass, more energy can be diverted to where it counts most - moving the car. The flywheel and clutch is one of the first areas that engine builders address when making the rotating assembly lighter for race engines. The dampening effect is just not needed on cars that are focused on performance.

In addition to releasing more power to the wheels, the lighter flywheel allows the engine to spin more freely, which improves throttle response. Again, the difference is huge as you watch the revs build faster than before. With the engine spinning easier the power band comes up much sooner. The stock steel flywheel feels lazy in comparison. There is a driving adjustment required to get used to how much faster the engine revs but that's not really a downside.

The JB lightweight flywheel is designed to be used with a factory organic clutch - the same clutch kit that you would get from any BMW dealer. This makes replacement clutch components easy to source and inexpensive when compared to specialized racing clutches. By using the factory BMW clutch, JB has also made the whole assembly easy to live with when used on the street. The clutch behaves the same as it originally did - just with better throttle response and more power! The JB flywheel can also be rebuilt with a new clutch contact surface - you don't have to buy a new flywheel.

Aluminum flywheels are considered 'single-mass' flywheels because they do not have the same dampening designs as an original 'dual-mass' flywheel. With a single-mass design more noise and vibration may be noticeable. There are steps you can take to minimize the noise - heavier weight transmission oil and clutch discs with anti-rattle springs (sprung-hub clutch).

Stock Flywheel Weight = 22.0lbs
JB Flywheel Weight = 8.5lbs

This flywheel includes the ignition trigger wheel.

This item fits the following BMWs:
1982-1987 E23 BMW 733i 735i
1982-1989 E24 BMW 633csi 635csi M6
1985-1988 E28 BMW 535i 535is M5

Show More Show Less

Condor Speed Shop M20+20 Engine Riser Motor Mount & Solid Transmissio...

T#:577564

Part#: S14M+T

Ships in 3 Business Days

$ 80.00 USD

Add to Wish List

Qty

$ 80.00 USD

Add to Wish List

These specific mounts are designed for those with clearance issues on extremely low E30s. They are 20mm taller than OEM mounts to add necessary clearance to ensure the oil pan sits above the stock subframe. Under hard braking the OEM rubber mounts allow the m20 to lean forward. Not only do these solid UHMW replacement mounts stiffen the engine and drivetrain, but they also raise the engine by 20mm, dramatically changing the responsiveness and raising the oil pan height of your E30. UHMW is an excellent general-purpose plastic with a unique combination of wear and corrosion resistance, low friction surface and impact strength. It is resistant to chemical attack and moisture absorption and retains key physical properties to -30 C. This kit includes Solid Transmission Mounts as well for fully solid powertrain mounting!

Show More Show Less

Genuine Mini Wheel Hub With Bearing - 33409813210

T#:207354

Part#: 33409813210

Ships in 1-2 days

18% off MSRP $ 342.57

MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.

$ 281.99 USD

Add to Wish List

Qty

18% off MSRP

$ 342.57

MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.

$ 281.99 USD

Add to Wish List

Genuine Mini Wheel Hub With Bearing - 33409813210

JB Racing Lightweight Aluminum Flywheel - E39 M5

T#:16606

Part#: 520-160-240

Ships in 8 Business Days

$ 903.00 USD

Add to Wish List

Qty

$ 903.00 USD

Add to Wish List

Aluminum flywheels are much lighter than the stock steel flywheel and that produces better throttle response and more available horsepower to the wheels for faster acceleration. The JB Racing aluminum flywheels are a direct replacement for the stock flywheel and work with stock clutch components for an easy upgrade with very little downside.

Modern flywheels are built with additional components and features that are designed to dampen and minimize vibrations from the engine and transmission. As a result they have become bloated in weight and that means more energy is used up just making the flywheel spin. The weight difference between an aluminum and steel flywheel is huge - sometimes more than 50% less. Without the additional mass, more energy can be diverted to where it counts most - moving the car. The flywheel and clutch is one of the first areas that engine builders address when making the rotating assembly lighter for race engines. The dampening effect is just not needed on cars that are focused on performance.

In addition to releasing more power to the wheels, the lighter flywheel allows the engine to spin more freely, which improves throttle response. Again, the difference is huge as you watch the revs build faster than before. With the engine spinning easier the power band comes up much sooner. The stock steel flywheel feels lazy in comparison. There is a driving adjustment required to get used to how much faster the engine revs but that's not really a downside.

The JB lightweight flywheel is designed to be used with a factory organic clutch - the same clutch kit that you would get from any BMW dealer. This makes replacement clutch components easy to source and inexpensive when compared to specialized racing clutches. By using the factory BMW clutch, JB has also made the whole assembly easy to live with when used on the street. The clutch behaves the same as it originally did - just with better throttle response and more power! The JB flywheel can also be rebuilt with a new clutch contact surface - you don't have to buy a new flywheel.

Aluminum flywheels are considered 'single-mass' flywheels because they do not have the same dampening designs as an original 'dual-mass' flywheel. With a single-mass design more noise and vibration may be noticeable. There are steps you can take to minimize the noise - heavier weight transmission oil and clutch discs with anti-rattle springs (sprung-hub clutch).

Stock Flywheel Weight = 40.0lbs
JB Flywheel Weight = 13.0lbs

This item fits the following BMWs:
1999-2003 E39 BMW M5

Show More Show Less

Stage 3 Performance Twin Disc Clutch Kit - Single Mass Flywheel - E8X...

T#:640069

Part#: MS-006-076

Ships on Jan 11, 2027

$ 1,299.99 USD

Add to Wish List

Qty

$ 1,299.99 USD

Add to Wish List

Working in collaboration with Competition Clutch, the up and coming German automotive performance company DKM has released a new line of high quality clutches made to satisfy your stock and modified performance needs! If you're having problems keeping power to the wheels, DKM has the solution. Their design, using high-grade materials, gives you increased strength and heat tolerance preventing wear and fade, ensuring increased torque capacity, quicker shifts, and a longer clutch life. Tracking your vehicle is all fun and games until your start burning through clutches as fast as you can afford to replace them. To end this cycle, the MS Twin Disc Clutch Kit is designed to hold up to 100 to 200% more torque capacity and provide you with a much improved clutch life span. The two organic disc setup provides additional contact surface areas to more evenly distribute pressure and heat for both a boost in performance and wear prevention. Kit Contents: Pressure Plate Two Organic Discs Steel Single Mass Flywheel Pilot Bearing/Bushing and Throw-out Bearing (when applicable) Alignment Tool **Due to the nature of lightened single mass flywheels added "NVH" or "chatter" will or may occur during operation. Accompanying modifications can also increase or decrease the amount of "NVH" or "chatter" in the drivetrain. Please contact our sales team with any questions.**

Show More Show Less

Genuine MINI Transmission Support Bracket / Mount

T#:49462

Part#: 22316754422

In Stock

7% off MSRP $ 287.99

MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.

$ 268.99 USD

Add to Wish List

Qty

7% off MSRP

$ 287.99

MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.

$ 268.99 USD

Add to Wish List

Genuine MINI SPPRT BRACKET,TRANSM.,WITH R

Genuine MINI Wiring Harness - Temperature Sensor

T#:51972

Part#: 24367551110

In Stock

6% off MSRP $ 186.99

MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.

$ 174.99 USD

Limited Qty Sale

Add to Wish List

Qty

6% off MSRP

$ 186.99

MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.

$ 174.99 USD

Limited Qty Sale

Add to Wish List

Genuine MINI WIRING HARNESS WITH TEMPERAT

Upper Engine Mount / Rubber

T#:5189123

Part#: 22118835572

In Stock

13% off MSRP $ 224.69

MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.

$ 194.99 USD

Add to Wish List

Qty

13% off MSRP

$ 224.69

MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.

$ 194.99 USD

Add to Wish List

Genuine MINI Clutch Kit Set

T#:178310

Part#: 21208607915

In Stock

27% off MSRP $ 481.02

MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.

$ 352.68 USD

Add to Wish List

Qty

27% off MSRP

$ 481.02

MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.

$ 352.68 USD

Add to Wish List

Genuine MINI SET CLUTCH PARTS

Genuine MINI Lower Engine Mount/Rubber

T#:22673

Part#: 22116783094

In Stock

$ 98.99 USD

Add to Wish List

Qty

$ 98.99 USD

Add to Wish List

Genuine MINI HOLDER WITH RUBBER MOUNTING

Automatic Transmission Filter Kit 314 137 0007/S

We Price Match - Give Us A Call or Chat!

T#:592322

Part#: 24347551087

Ships on Sep 15, 2026

$ 66.99 USD

Add to Wish List

Qty

$ 66.99 USD

Add to Wish List

Engine Mount

T#:641903

Part#: 22118835574

Ships in 1-2 days

6% off MSRP $ 224.69

MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.

$ 211.99 USD

Add to Wish List

Qty

6% off MSRP

$ 224.69

MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.

$ 211.99 USD

Add to Wish List

BMW E36 328i, Z3 2.8 JB Racing Lightweight Aluminum Flywheel ...

T#:3774

Part#: 520-030-240

In Stock

$ 714.00

This product was last offered at the strikethrough price on
06-08-2026

$ 652.99 USD

Limited Qty Sale

Add to Wish List

Qty

$ 714.00

This product was last offered at the strikethrough price on
06-08-2026

$ 652.99 USD

Limited Qty Sale

Add to Wish List

BMW E36 328i, Z3 2.8 JB Racing Lightweight Aluminum Flywheel offers a significant performance upgrade by replacing the heavy stock steel flywheel with a much lighter aluminum version. This JB Racing flywheel is designed to deliver faster acceleration, improved throttle response, and enhanced overall performance for your BMW.

The modern stock flywheels are burdened with additional components meant to dampen vibrations, which unfortunately adds unnecessary weight. The JB Racing aluminum flywheel, weighing just 10.0 lbs compared to the stock 25.0 lbs, eliminates this excess mass, allowing more power to reach the wheels and reducing the energy wasted on spinning the flywheel. Engine builders prioritize lightweight flywheels when optimizing race engines for maximum efficiency, and the difference is especially noticeable in how quickly the engine revs and reaches its power band.

This JB Racing lightweight flywheel is a direct replacement for the stock flywheel and is compatible with the factory BMW organic clutch. This compatibility ensures that you can use standard replacement clutches, making maintenance simple and cost-effective. The flywheel can also be resurfaced for a fresh contact surface, so there’s no need to buy a new one when it’s time to replace the clutch.

While single-mass aluminum flywheels like this one may result in slightly more noise and vibration compared to dual-mass designs, this can be managed with heavier transmission oil and sprung hub clutches, such as the Sachs Performance clutch available through Turner Motorsport.

Faster acceleration: Reduces the rotational mass for quicker engine response.
Improved throttle response: Engine revs more freely and builds RPM faster.
Enhanced performance: More power delivered to the wheels for better driving dynamics.
Cost-effective maintenance: Compatible with factory BMW organic clutches and can be resurfaced.
Direct replacement: Easy upgrade with no modifications required.

Vehicle Compatibility:

1996-1999 E36 BMW 328i, 328is, 328ic
1997-1998 Z3 BMW Z3 2.8

Show More Show Less

Genuine MINI Shifting Cable Selector Shaft - Mass Absorber

T#:52946

Part#: 25117594646

Ships in 2 Business Days

7% off MSRP $ 177.74

MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.

$ 165.99 USD

Add to Wish List

Qty

7% off MSRP

$ 177.74

MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.

$ 165.99 USD

Add to Wish List

Genuine MINI ELECTOR ROD SELECT. CABLE/M

Genuine MINI Clutch Release Fork Lever

T#:193303

Part#: 23117515839

Ships in 2 Business Days

9% off MSRP $ 152.22

MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.

$ 138.99 USD

Add to Wish List

Qty

9% off MSRP

$ 152.22

MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.

$ 138.99 USD

Add to Wish List

Genuine Mini Clutch Rel.Fork Lever

ENGINE MOUNT B46 2.0L

T#:4251507

Part#: 22118835566

In Stock

$ 204.99 USD

Add to Wish List

Qty

$ 204.99 USD

Add to Wish List

Enhance the stability and performance of your BMW's B46 2.0L engine with the durable Engine Mount. This high-quality rubber mount, equipped with sturdy metal brackets, ensures optimal support and reduces vibrations, contributing to a smoother and more efficient driving experience.

Stability Improvement: The Engine Mount enhances overall stability for improved driving control.
Vibration Reduction: Designed to minimize engine vibrations, resulting in a smoother ride.
Durable Construction: High-quality rubber and metal brackets ensure long-lasting performance.
Engine Support: Provides crucial support to the B46 2.0L engine, optimizing its functionality.

Upgrade your BMW's driving experience with the B46 2.0L Engine Mount, a reliable component designed for stability and performance.

Show More Show Less

2002, 2002Tii JB Racing Lightweight Aluminum Flywheel 228mm

T#:3762

Part#: 520-100-228

In Stock

$ 581.00 USD

Add to Wish List

Qty

$ 581.00 USD

Add to Wish List

Aluminum flywheels are much lighter than the stock steel flywheel and that produces better throttle response and more available horsepower to the wheels for faster acceleration. The JB Racing aluminum flywheels are a direct replacement for the stock flywheel and work with stock clutch components for an easy upgrade with very little downside.

Modern flywheels are built with additional components and features that are designed to dampen and minimize vibrations from the engine and transmission. As a result they have become bloated in weight and that means more energy is used up just making the flywheel spin. The weight difference between an aluminum and steel flywheel is huge - sometimes more than 50% less. Without the additional mass, more energy can be diverted to where it counts most - moving the car. The flywheel and clutch is one of the first areas that engine builders address when making the rotating assembly lighter for race engines. The dampening effect is just not needed on cars that are focused on performance.

In addition to releasing more power to the wheels, the lighter flywheel allows the engine to spin more freely, which improves throttle response. Again, the difference is huge as you watch the revs build faster than before. With the engine spinning easier the power band comes up much sooner. The stock steel flywheel feels lazy in comparison. There is a driving adjustment required to get used to how much faster the engine revs but that's not really a downside.

The JB lightweight flywheel is designed to be used with a factory organic clutch - the same clutch kit that you would get from any BMW dealer. This makes replacement clutch components easy to source and inexpensive when compared to specialized racing clutches. By using the factory BMW clutch, JB has also made the whole assembly easy to live with when used on the street. The clutch behaves the same as it originally did - just with better throttle response and more power! The JB flywheel can be rebuilt too with a new clutch contact surface.

Aluminum flywheels are considered 'single-mass' flywheels because they do not have the same dampening designs as an original 'dual-mass' flywheel. With a single-mass design more noise and vibration may be noticeable. There are steps you can take to minimize the noise - heavier weight transmission oil and clutch discs with anti-rattle springs (sprung-hub clutch).

Stock Flywheel Weight = 16.5
JB Flywheel Weight = 8lbs

This item fits the following BMWs:
1968-1973 2002 BMW 2002 2002tii

Show More Show Less

VTT - Carbon Fiber Driveshaft - G87 M2

T#:35998387

Part#: VTT-BMW-CF-G87

Ships in 10 Business Days

$ 2,136.99 USD

Add to Wish List

Qty

$ 2,136.99 USD

Add to Wish List

The Vargas Turbo Technologies Carbon Fiber Driveshaft for the G87 M2 is a game-changer for BMW G87 M2 enthusiasts who demand top-tier performance and reliability. Engineered with precision and crafted from advanced carbon fiber, this driveshaft delivers a perfect balance of strength, lightweight construction, and improved drivability. Ideal for spirited street driving or aggressive track days, it sets a new standard in drivetrain performance.

Key Features and Benefits Lightweight carbon fiber reduces rotational mass for faster acceleration and improved handling Exceptional strength and durability to withstand high-torque applications Enhanced drivetrain efficiency with minimized power loss during transmission Precision-engineered for the BMW G87 M2 to ensure seamless installation Vibration-damping properties provide a smoother and quieter ride Available at Turner Motorsport, a trusted name in BMW performance upgrades The Vargas Turbo Technologies carbon fiber driveshaft is the ultimate upgrade for your BMW G87 M2, enhancing performance, efficiency, and driving enjoyment.

Show More Show Less

VTT- Rear Differential Bushing Insert Kit- F97/F98 X3M X4M

T#:25739329

Part#: VTT-F9X-RBIK

Ships in 10 Business Days

$ 135.99 USD

Add to Wish List

Qty

$ 135.99 USD

Add to Wish List

Billet Transfer Case Bushing Inserts

T#:25739322

Part#: VTT-BTCBI

Ships in 10 Business Days

$ 136.99 USD

Add to Wish List

Qty

$ 136.99 USD

Add to Wish List

E36, E46 JB Racing Ultra-Light Racing Clutch/Flywheel Assembly ...

T#:340509

Part#: WCCLUTCH

Ships in 5 Business Days

Starting at $ 1,999.00 USD

Add to Wish List

Starting at $ 1,999.00 USD

Add to Wish List

The ultimate in a racing flywheel and clutch! This was developed for use in our E36 and E46 World Challenge Touring Cars. The combined weight of the clutch and flywheel is only 11lbs!!!

This multi-disc (2 or 3 disc setups) offer a minimal flywheel mass (enough to include a factory ring gear for the starter) and a small 5.5" clutch assembly rated to 500hp. By saving as much weight as possible less energy is used in simply spinning the flywheel/clutch assembly and that means a lot more power and torque is available at the drive wheels. The flywheel and clutch is one of the first areas that engine builders address when making the rotating assembly lighter for race engines and this is among the most advanced and lightest racing clutch kits available for your BMW race car.

The JB Ultra-Light Performance racing clutch is available in 2-disc or 3-disc setups. We used the 5.5"/140mm size in our Touring Cars but larger sizes are available too. This is a turn-key racing clutch and flywheel kit that you don't have to engineer or spec yourself. This is the same clutch setup we used when winning the 2003 and 2004 Touring Car Championships - the quality and performance is unquestionable. That series also employed standing starts at each race and this clutch setup performed flawlessly with nearly a full season of racing on them before needing a change.

JB Ultra-Light flywheels include:

precision CNC machined aluminum flywheel

zero-balanced up to 10,000 RPM

replaceable hardened steel clutch friction surface

Helicoil threaded inserts

high-strength grade 10.9 hardware

multi-disc racing clutch with Performance racing pressure plate

JB Racing throw-out bearing with custom bobbin
This is a true racing clutch and will not function as a street-able clutch at all. It behaves as an on/off switch with no slippage allowed. Extreme care must be used when driving on to trailers and around the paddock. But when driven correctly the life span of this clutch is amazing - we could get a full season of racing a 300hp M54 from this clutch setup including standing starts at every race! Replacement clutch components and flywheel rebuilding are available.

A properly adjusted clutch stop is required for use with this clutch kit.

Stock Flywheel + Clutch Weight = 45+lbs
JB Ultra-Light Flywheel & Clutch Weight = 11lbs

This item fits the following BMWs:
1992-1999 E36 BMW 325i 325is 328i 328is M3
1999-2006 E46 BMW 323i 323ci 325i 325ci 328i 328ci 330i 330ci (5-speed)
1997-2002 Z3 BMW Z3 2.3 Z3 2.5i Z3 2.8 Z3 3.0i M Roadster M Coupe
2003-2005 E85 BMW Z4 2.5i (5-speed)

Show More Show Less

E30 325e JB Racing Lightweight Aluminum Flywheel (Replaces Dual-Mass ...

T#:3749

Part#: 520-120-228

In Stock

$ 854.00 USD

Add to Wish List

Qty

$ 854.00 USD

Add to Wish List

Aluminum flywheels are much lighter than the stock steel flywheel and that produces better throttle response and more available horsepower to the wheels for faster acceleration. The JB Racing aluminum flywheels are a direct replacement for the stock flywheel and work with stock clutch components for an easy upgrade with very little downside.

Modern flywheels are built with additional components and features that are designed to dampen and minimize vibrations from the engine and transmission. As a result they have become bloated in weight and that means more energy is used up just making the flywheel spin. The weight difference between an aluminum and steel flywheel is huge - sometimes more than 50% less. Without the additional mass, more energy can be diverted to where it counts most - moving the car. The flywheel and clutch is one of the first areas that engine builders address when making the rotating assembly lighter for race engines. The dampening effect is just not needed on cars that are focused on performance.

In addition to releasing more power to the wheels, the lighter flywheel allows the engine to spin more freely, which improves throttle response. Again, the difference is huge as you watch the revs build faster than before. With the engine spinning easier the power band comes up much sooner. The stock steel flywheel feels lazy in comparison. There is a driving adjustment required to get used to how much faster the engine revs but that's not really a downside.

The JB lightweight flywheel is designed to be used with a factory organic clutch - the same clutch kit that you would get from any BMW dealer. This makes replacement clutch components easy to source and inexpensive when compared to specialized racing clutches. By using the factory BMW clutch, JB has also made the whole assembly easy to live with when used on the street. The clutch behaves the same as it originally did - just with better throttle response and more power! The JB flywheel can also be rebuilt with a new clutch contact surface - you don't have to buy a new flywheel.

Aluminum flywheels are considered 'single-mass' flywheels because they do not have the same dampening designs as an original 'dual-mass' flywheel. With a single-mass design more noise and vibration may be noticeable. There are steps you can take to minimize the noise - heavier weight transmission oil and clutch discs with anti-rattle springs (sprung-hub clutch).

The JB flywheel includes ignition trigger wheel.

This flywheel replaces the stock original dual-mass flywheel and should only be used with the corresponding 'dual-mass' clutch kit. According to BMW the dual mass flywheel was installed in all 325/325e from 5/86 on but we have seen some later cars with a single-mass flywheel. The age of the car almost guarantees one or more clutch replacements and possibly a change to the original flywheel as well. You may not know which flywheel is currently installed until the flywheel cover or the transmission is removed.

Stock Flywheel Weight = 27.5lbs
JB Flywheel Weight = 10.0lbs

This item fits the following BMWs:
1984-1988 E30 BMW 325e 325es (with dual mass flywheel)

Show More Show Less

E30 325e JB Racing Lightweight Aluminum Flywheel (Replaces Single-Mas...

T#:3763

Part#: 520-070-228

Ships in 5 Business Days

$ 630.00 USD

Add to Wish List

Qty

$ 630.00 USD

Add to Wish List

Aluminum flywheels are much lighter than the stock steel flywheel and that produces better throttle response and more available horsepower to the wheels for faster acceleration. The JB Racing aluminum flywheels are a direct replacement for the stock flywheel and work with stock clutch components for an easy upgrade with very little downside.

Modern flywheels are built with additional components and features that are designed to dampen and minimize vibrations from the engine and transmission. As a result they have become bloated in weight and that means more energy is used up just making the flywheel spin. The weight difference between an aluminum and steel flywheel is huge - sometimes more than 50% less. Without the additional mass, more energy can be diverted to where it counts most - moving the car. The flywheel and clutch is one of the first areas that engine builders address when making the rotating assembly lighter for race engines. The dampening effect is just not needed on cars that are focused on performance.

In addition to releasing more power to the wheels, the lighter flywheel allows the engine to spin more freely, which improves throttle response. Again, the difference is huge as you watch the revs build faster than before. With the engine spinning easier the power band comes up much sooner. The stock steel flywheel feels lazy in comparison. There is a driving adjustment required to get used to how much faster the engine revs but that's not really a downside.

The JB lightweight flywheel is designed to be used with a factory organic clutch - the same clutch kit that you would get from any BMW dealer. This makes replacement clutch components easy to source and inexpensive when compared to specialized racing clutches. By using the factory BMW clutch, JB has also made the whole assembly easy to live with when used on the street. The clutch behaves the same as it originally did - just with better throttle response and more power! The JB flywheel can also be rebuilt with a new clutch contact surface - you don't have to buy a new flywheel.

Aluminum flywheels are considered 'single-mass' flywheels because they do not have the same dampening designs as an original 'dual-mass' flywheel. With a single-mass design more noise and vibration may be noticeable. There are steps you can take to minimize the noise - heavier weight transmission oil and clutch discs with anti-rattle springs (sprung-hub clutch).

The JB flywheel includes ignition trigger wheel.

This flywheel replaces the stock original single-mass flywheel and should only be used with the corresponding 'single-mass' clutch kit. According to BMW the single mass flywheel was installed in all 325e up to 5/86 production date but we have seen some later cars with a single-mass flywheel. The age of the car almost guarantees one or more clutch replacements and possibly a change to the original flywheel as well. You may not know which flywheel is currently installed until the flywheel cover or the transmission is removed.

Stock Flywheel Weight = 24.0lbs
JB Flywheel Weight = 8.5lbs

This item fits the following BMWs:
1984-1988 E30 BMW 325e 325es (with single mass flywheel)

Show More Show Less

S55 Billet Motor Mount Inserts

T#:597677

Part#: VTT-INSERT-2

Ships in 10 Business Days

$ 178.99 USD

Add to Wish List

Qty

$ 178.99 USD

Add to Wish List

Instead of completely replacing the mount, simply make a billet aluminum insert for them. This leaves the feel of the factory mount in place but stiffens them up quite a bit removing unwanted engine movement without rattling your teeth out or emptying your wallet.

Show More Show Less

E34 535i JB Racing Lightweight Aluminum Flywheel

T#:647

Part#: 520-170-240

Ships in 1 Business Day

$ 714.00 USD

Add to Wish List

Qty

$ 714.00 USD

Add to Wish List

Aluminum flywheels are much lighter than the stock steel flywheel and that produces better throttle response and more available horsepower to the wheels for faster acceleration. The JB Racing aluminum flywheels are a direct replacement for the stock flywheel and work with stock clutch components for an easy upgrade with very little downside.

Modern flywheels are built with additional components and features that are designed to dampen and minimize vibrations from the engine and transmission. As a result they have become bloated in weight and that means more energy is used up just making the flywheel spin. The weight difference between an aluminum and steel flywheel is huge - sometimes more than 50% less. Without the additional mass, more energy can be diverted to where it counts most - moving the car. The flywheel and clutch is one of the first areas that engine builders address when making the rotating assembly lighter for race engines. The dampening effect is just not needed on cars that are focused on performance.

In addition to releasing more power to the wheels, the lighter flywheel allows the engine to spin more freely, which improves throttle response. Again, the difference is huge as you watch the revs build faster than before. With the engine spinning easier the power band comes up much sooner. The stock steel flywheel feels lazy in comparison. There is a driving adjustment required to get used to how much faster the engine revs but that's not really a downside.

The JB lightweight flywheel is designed to be used with a factory organic clutch - the same clutch kit that you would get from any BMW dealer. This makes replacement clutch components easy to source and inexpensive when compared to specialized racing clutches. By using the factory BMW clutch, JB has also made the whole assembly easy to live with when used on the street. The clutch behaves the same as it originally did - just with better throttle response and more power! The JB flywheel can also be rebuilt with a new clutch contact surface - you don't have to buy a new flywheel.

Show More Show Less

Condor Speed Shop Solid Motor & Transmission Mount Set - E34 535i w/ ...

T#:577962

Part#: E34M30_TRANS

Ships in 2 Business Days

$ 139.99 USD

Add to Wish List

Qty

$ 139.99 USD

Add to Wish List

Solid UHMW 535i engine mounts for your m30 powered E34. Under hard braking the stock mounts allow the engine to pitch forward and to the side. These solid UHMW replacement mounts stiffen the engine and drivetrain, dramatically changing the responsiveness of your E34. These solid UHMW mounts are a direct replacement for your original E34 535i BMW OEM rubber motor mounts. UHMW is an excellent general-purpose plastic with a unique combination of wear and corrosion resistance, low friction surface and impact strength. It is resistant to chemical attack and moisture absorption and retains key physical properties to -30 C.

Show More Show Less

Z4 M HD Clutch and Flywheel Kit

T#:878

Part#: 520-010S-S873G

Ships in 9 Business Days

$ 1,488.61 USD

Add to Wish List

Qty

$ 1,488.61 USD

Add to Wish List

This lightweight aluminum flywheel w/ Heavy Duty "sprung-hub" clutch package is the best-engineered solution for E46 325 and 330 models with the 6-speed transmission, Z4 2.5/3.0, and Z4 M Roadster and M Coupe. Instead of picking a clutch from another car that may or may not work at all, the engineers at JB Racing have taken all of the guess work out of this upgrade and incorporated a Sachs sport sprung-hub clutch with the correct pressure plate and combined it with their most-popular aluminum lightweight flywheel. The Sachs HD clutch disc has a sprung hub to minimize noise and vibration and organic linings to give the feel and engagement of a stock clutch. Mixing and matching of the incorrect clutch, pressure plate, and flywheel components can lead to inconsistent engagement and feel -- why make your clutch feel worse?

In addition, the Sachs HD pressure plate will clamp with greater force -- allowing approximately 350 ft-lbs of torque, which makes it an obvious upgrade from the stock clutch kit. And with the aluminum flywheel weight savings is substantial over the stock dual-mass flywheel - which allows your motor to spool up faster and transmit more HP to the ground.

Because Sachs is an OE supplier to most German cars, replacement parts are just a phone call away. This kit uses the stock throw-out bearing (included in the price).

Z4 M Sport Clutch and Flywheel Applications:
2006-2008 E85 Z4, E86 Z4 Z4 M Roadster, Z4 M Coupe

Show More Show Less

Condor Speed Shop Solid Motor & Transmission Mount Set - E30 w/ M10 ...

T#:577966

Part#: E30_M10M_TRANS

In Stock at Vendor

$ 115.00 USD

Add to Wish List

Qty

$ 115.00 USD

Add to Wish List

These solid UHMW motor mounts are made specifically for M10 powered e30s. Under hard braking the stock mounts allow the M10 to lean forward. These solid UHMW replacement mounts stiffen the engine and drivetrain, dramatically changing the responsiveness of your 318. These solid UHMW motor mounts are a direct replacement for OEM rubber motor mounts. UHMW is an excellent general-purpose plastic with a unique combination of wear and corrosion resistance, low friction surface and impact strength. It is resistant to chemical attack and moisture absorption and retains key physical properties to -30 C. Includes solid transmission mounts as well.

Show More Show Less

Condor Speed Shop Solid Engine & Transmission Mount Set - E34 525i ...

For Vehicles With Manual Transmission

T#:577960

Part#: E34M_TRANS

Ships in 1 Business Day

$ 139.00 USD

Add to Wish List

Qty

$ 139.00 USD

Add to Wish List

Solid UHMW 525i engine mounts for your M50tu powered E34. Under hard braking the stock mounts allow the motor to pitch forward and to the side. These solid UHMW replacement mounts stiffen the engine and drivetrain, dramatically changing the responsiveness of your BMW E34. These solid UHMW motor mounts are a direct replacement for your original E34 525i BMW OEM rubber motor mounts. UHMW is an excellent general-purpose plastic with a unique combination of wear and corrosion resistance, low friction surface and impact strength. It is resistant to chemical attack and moisture absorption and retains key physical properties to -30 C. Includes transmission mounts.

Show More Show Less

Project Cars

SELECT YOUR BMW

Sub-Categories

BMW E9X 335i BMS Differential Support Bracket Brace - Small Case

Benefits:

Select Vehicle

Purpose

Category

Brand

Price

Special Offers

Shipping

Narrow Results