BMW Drivetrain Parts

Turner Motorsport Lightweight N54 Flywheel & Upgraded Clutch Kit

Unlock the full potential of your N54-powered BMW with our performance-driven clutch and flywheel kit. Designed to enhance daily drivability while delivering increased power handling and improved throttle response, this kit is the ultimate upgrade for enthusiasts seeking more from their vehicle.

Why Choose This Kit?
This setup features the Turner Lightweight N54 Flywheel, precision-engineered for quicker acceleration, faster rev-matching, and a more responsive driving experience. Paired with an upgraded OE clutch from the high-performance 335is and F10 550i(V8 Bi-Turbo), this combo is capable of handling over 500 ft-lbs of torque while maintaining smooth, factory-like engagement and durability.

The factory dual-mass flywheel may prioritize smoothness and efficiency, but it comes at the cost of responsiveness and is prone to failure in high-performance applications. The Turner Lightweight Flywheel solves these issues with a single-mass design that strikes the perfect balance between comfort, performance, and reliability making it ideal for both daily driving and spirited track use.

Kit Contents:

Turner Lightweight N54 Single-Mass Flywheel (18.6 lbs, 10 lbs lighter than stock)
Upgraded OE Clutch – Supports 500 ft-lbs+
OE Clutch Fork - P# 21517564027
OE Throwout Bearing
Clutch Alignment Tool - P# 056212LA01A
Brass Clutch Fork Pivot Pin - P# 21511223328
OE Flywheel Bolts - P# 11227520706
OE Pressure Plate Screws - P# 21207548052
Pivot Pin Retaining Spring - P# 21517570284
Transmission Mating Dowels - P# 11117524470
Flywheel Features:

Precision-machined 4140 HT heat-treated chromoly steel for durability
Black oxide coating to resist corrosion
8620 steel pilot bearing pin for maximum wear resistance
Precision balanced to exceed OEM standards
Optimized step height for longer clutch life and consistent performance
Clutch:

Upgrade for 135i/335i/535i models from the 335is! Featuring a heavy-duty clutch with more holding power and a stock-like pedal feel. Excellent solution for If your clutch is slipping, or the engagement isn't what it used to be, it's time for a replacement. Slipping clutches won't allow your BMW to accelerate properly and can pose problems under a load such as going up large inclines. Also, a worn clutch can cause less precise and engaging shifts. By replacing your clutch you will restore performance and driving pleasure.

This clutch is an excellent upgrade for non 335is/550i/650i models. It features a more heavy-duty clutch disc and more holding power with stock-like pedal effort.

Transform your driving experience with this Turner Motorsport clutch and flywheel kit - engineered for power, performance, and everyday reliability.

Differential Fluid Extraction Adapter is an essential tool for efficiently draining and refilling differential fluid, ensuring your vehicle's differential system remains in optimal condition. Designed to work with most extraction pumps, this adapter simplifies maintenance tasks, making it easier to service your differential without the mess or hassle of traditional methods.

• Efficient fluid extraction: Allows for quick and clean draining of differential fluid.
• Versatile compatibility: Works with most extraction pumps, offering flexibility for various vehicle makes and models.
• Hassle-free maintenance: Simplifies the process of refilling and draining differential fluid, reducing time and effort.
• Durable construction: Built from high-quality materials to withstand frequent use and harsh conditions.
• Easy installation: Designed for a secure fit and easy attachment to extraction pumps.

This Differential Fluid Extraction Adapter is a must-have for any vehicle owner looking to maintain the longevity and performance of their differential system.

Since established in 2004, GSP North America has positioned itself as a leading supplier of New Axles in North America.GSP’s new axle program consistently offers the best application coverage, most SKU count, and more new numbers than any other competitors. GSP’s hub assembly program was introduced to North America market in 2010 and has grown into one the most trustable programs in US market.

This item fits the following BMWs: 

E36 BMW M3

Bushings tends to wear over time and split or even break free from the internal sleeve, causing excessive movement and sloppy control feel. OEM Lemförder bushings are the perfect option to restore suspension back to day 1 quality.

OEM Lemförder is an engineering company that focuses on high-quality, precision manufacturing of critical suspension and steering components. Providing exceptionally high quality parts directly to BMW, as well as 50+ other big name automotive companies, such as Mercedes and Audi, their history of reliability and variety of offered parts makes them one of the biggest names for a go-to OEM parts provider. Lemförder parts place an important emphasis on design, production, and assembly, ensuring maximum reliability. They even coat all parts possible with corrosion protection for extended longevity.

As a leading source of high performance BMW parts and accessories since 1993, we at Turner Motorsport are honored to be the go-to supplier for tens of thousands of enthusiasts the world over. With over two decades of parts, service, and racing experience under our belt, we provide only quality performance and replacement parts.  All of our performance parts are those we would (and do!) install and run on our own cars, as well as replacement parts that are Genuine BMW or from OEM manufacturers. We only offer parts we know you can trust to perform!

All new hardware for installing your G260 on an M20 motor, including new dowels and 10mm bolt that goes from the engine side into the transmission.

Whether your refreshing the transmission, doing the clutch and flywheel or doing a manual swap get a new set of hardware for piece of mind and many more service intervals.

Kit Contents:

M12x45 Torx bolt - 23001222890 (QTY2)
M12x75 Torx bolt - 23001222893 (QTY2)
Washer - 07119906063 (QTY 4)
Dowel - 11117524470 (QTY2)
M8x50 ASA Bolt - 23001222887 (QTY 4)
Wave Washer - 07119904115 (QTY 4)
M6x16 Hex Bolt - 07119913015 (QTY 1)
M10x65 Torx Bolt - 07129904681 (QTY2)
Wave Washer - 07119904463 (QTY2)
Hex Nut - 07129904865 (QTY2)

BMW E36 E46 E30 Universal Flex Disc is an essential component located between the driveshaft and the transmission, designed to absorb hard vibrations and shocks during gear shifts. Over time, the rubber in the flex disc can degrade, leading to increased vibrations and clunking noises. Replacing this disc ensures your BMW drives smoothly and maintains optimal performance. Turner Motorsport offers this high-quality replacement part, manufactured by URO Parts, a leading provider of direct replacement components. URO Parts adheres to ISO 9000 certification standards, guaranteeing long-lasting durability and reliable performance.

• Absorbs vibrations and shocks from gear shifts
• Reduces clunking noises and enhances driving comfort
• Ensures smooth and optimal vehicle performance
• High-quality construction by URO Parts
• ISO 9000 certified for durability and reliability

Since established in 2004, GSP North America has positioned itself as a leading supplier of New Axles in North America.GSP’s new axle program consistently offers the best application coverage, most SKU count, and more new numbers than any other competitors. GSP’s hub assembly program was introduced to North America market in 2010 and has grown into one the most trustable programs in US market.

This item fits the following BMWs: 

E24 BMW 633CSi M6

E28 BMW 524td 528e 533i 535i 535is M5

E34 BMW 530i 535i 540i M5

Since established in 2004, GSP North America has positioned itself as a leading supplier of New Axles in North America.GSP’s new axle program consistently offers the best application coverage, most SKU count, and more new numbers than any other competitors. GSP’s hub assembly program was introduced to North America market in 2010 and has grown into one the most trustable programs in US market.

This item fits the following BMWs: 

E34 BMW 525i 525iT 530i 535i

Since established in 2004, GSP North America has positioned itself as a leading supplier of New Axles in North America.GSP’s new axle program consistently offers the best application coverage, most SKU count, and more new numbers than any other competitors. GSP’s hub assembly program was introduced to North America market in 2010 and has grown into one the most trustable programs in US market.

This item fits the following BMWs: 

E46 BMW 325xi 330xi

Since established in 2004, GSP North America has positioned itself as a leading supplier of New Axles in North America.GSP’s new axle program consistently offers the best application coverage, most SKU count, and more new numbers than any other competitors. GSP’s hub assembly program was introduced to North America market in 2010 and has grown into one the most trustable programs in US market.

This item fits the following BMWs: 

E46 BMW 325xi 330xi

Don't neglect your motor mounts! Most stock BMW motor mounts are fluid filled and the stiffness of the mount depends on this fluid. But over time the fluid leaks out and the strength of the mount is greatly reduced. A worn motor mount allows the engine to twist and shift around. The harder you're driving the more shift will occur. As the engine is moving around it can contact other parts in the engine bay - usually cooling related. The mechanical fan can hit the radiator; the A/C compressor can hit a radiator hose, the exhaust will flex and may break. Twisting of the engine can also lead to shifting problems as the transmission twists with it. There are countless issues related to worn or compressed motor mounts so don't overlook these as a regular replacement item (every 50,000 miles).

Lemförder is an engineering company that focuses on high-quality, precision manufacturing of critical suspension and steering components. Providing exceptionally high quality parts directly to BMW, as well as 50+ other big-name automotive companies, such as Mercedes and Audi, their history of reliability and variety of offered parts makes them one of the biggest names for a go-to OEM parts provider.

Fits the following chassis:
E39 w/ M54 M52