This braided stainless steel line replaces the stock hydraulic hose connecting your clutch slave cylinder to the clutch master cylinder. There are several deficiences with rubber, especially as it ages - when new the rubber expands and swells under pressure and the pedal can feel spongy. As rubber ages and is exposed to extreme temperatures the rubber can harden and even shrink (common on brake hoses), which results in a stiff pedal. Rubber clutch lines do not stand up to the stresses of hard use. ECS Exact-Fit stainless reinforced clutch lines provide more confident and dependable shifting by maintaining consistent line pressure, long lasting corrosion resistance, and increased protection from failure. These lines are reinforced with braided stainless steel mesh, affording superior expansion resistance. This resistance to expansion creates a firmer pedal, and a more direct clutch pedal feel. The signature red polymer coating provides additional protection from the elements and abrasion.

This particular stainless steel clutch line fits the following BMWs:
1999-2005 E46 3 Series (all) including 323i, 323Ci, 325i, 325xi, 325Ci, 328i, 328Ci, 330i, 330xi, 330Ci
2001-2006 E46 M3 (manual transmission only, no SMG)
2004-2009 X3 SAV including X3 2.5, X3 3.0

Some modifications to your vehicle may not produce power to create gains in the overall performance of your driving. When you add a "Po' Boy" clutch stop to your BMW the performance gain is directly felt in the driving experience.

The ECS clutch stop allows the driver to fine tune the position of the clutch pedal to closely match the engagement point for precise, quicker shifting. The adjustment range found in this product can be set to the stock engagement point or can be adjusted to follow the wear of the clutch.  Meaning your new experience will never change all the way to the end of the clutch life and can be reset to enjoy the next clutch.

Note: This modification might require some slight modification to the clutch switch mounting bracket, which can be bent slightly by hand.

Eliminate the factory clutch delay valve and enjoy faster, more precise clutch engagement with the ECS Clutch Delay Valve (CDV) Removal Tool Kit. Designed for F and G-Chassis manual BMWs, this kit makes removing the hydraulic restrictor safe, simple, and reliable, no slave cylinder removal required.

Most modern BMWs come from the factory with a plastic slave cylinder featuring a CDV, intended to smooth engagement and reduce driveline shock for less experienced drivers. In practice, this restrictor can dull pedal feedback, slow shifts, and increase clutch wear. Removing it restores the sharp, direct clutch feel that BMW enthusiasts expect.

Key Benefits:

Faster, more predictable clutch engagement
Sharper pedal response and connected driving feel
No need to remove the slave cylinder
Tool Design:

Machined from durable 304 stainless steel
Includes precision removal and insertion tools
Knurled grip for easy handling
Built-in depth and angle control protects internal surfaces and ensures proper grommet alignment
Removal and Installation:

Disconnect the Clutch Line
Remove the clutch line from the slave cylinder to access the factory clutch delay valve.
Remove the Restrictor Plate
Thread the removal tool into the center of the small grommet. Once engaged, carefully pull the tool to remove the grommet and restrictor plate. The small rubber sealing O-ring will come out along with the plate.
Reinstall the O-Ring
Place the rubber O-ring onto the installation tool. Insert the tool into the slave cylinder to properly seat the O-ring in its original position.
Reconnect and Bleed the Clutch
Reattach the clutch line, add fluid, and bleed the system according to your manufacturer’s instructions.
Enjoy Enhanced Clutch Feel
With the delay valve removed, your clutch now engages faster and more predictably, giving your manual transmission the sharp, connected feel it was designed for.

Looking to eliminate your dual-mass flywheel? Overwhelmed with all the options, but hearing complaints about so many of them with rattling or chatter from them? Problem solved. Introducing the all-new Lightweight Performance Flywheel from ECS Tuning. Engineered in-house with the enthusiast daily driver in mind, this is the perfect option for those wanting a lightweight flywheel without the annoying chatter heard from so many other options on the market. Designed to accommodate all conditions: from Sunday drives through the country, to the abuse of the track. No matter your driving style or ability, this is the flywheel and clutch kit for you.

Key Features:

Eliminates factory dual-mass flywheel for:
Crisper shifts
Improved throttle response
Improved acceleration (We measured a .4s decrease in 0-60 times on an otherwise-stock E36 328i!)
Lower replacement cost
Hardened 4140 Chromoly Steel for excellent engagement feel and wear resistance; zinc plated for corrosion resistance
Designed for use with any E34 M5 pressure plate and clutch for OE-type clutch feel
Sprung-hub clutch disc to eliminate chatter at idle and reduce driveline shock loading
Weighs in at just 16.5lbs!
SFI tested and certified to ensure safe operation under all conditions
Includes ECS performance flywheel, clutch kit with throwout bearing, pilot bearing and all flywheel and pressure plate hardware
Why is SFI testing and certification important?

The SFI Foundation, Inc. (SFI) is a non-profit organization established to issue and administer standards for the quality assurance of specialty performance and racing equipment. SFI certification indicates a flywheel has been certified using industry-standard SFI Spec 1.1 standards by an independent testing body to ensure quality of both design and materials for flywheels utilized in competitive motorsports.

Having successfully passed SFI certification, this flywheel has an individual SFI serial number found in a laser etching, and on an affixed sticker. This certification means the ECS-engineered flywheel is safe and reliable during the rigors of competitive racing; it's also safe and reliable for years and years of street use.

BMW E39 M5 South Bend Stage 2 Daily Clutch Kit provides a powerful, durable upgrade for the E39 M5, combining exceptional torque capacity with daily drivability. Turner Motorsport offers this clutch kit, designed to handle high horsepower modifications with ease. Featuring a heavy-duty pressure plate and high metal-content organic disc, this clutch system delivers double the friction of a stock lining and a burst strength up to 12,000 RPM.

Ideal for both daily use and moderate race conditions, this Stage 2 clutch kit is rated to manage up to 440 lbs/ft of torque. The solid-hub center section is optimized for compatibility with the OE dual-mass flywheel, ensuring a smooth, reliable driving experience while maintaining a nearly stock pedal feel.

• Heavy-Duty Pressure Plate: Increased clamp load for superior torque handling with minimal change in pedal pressure
• High Metal-Content Organic Disc: Provides double the friction coefficient and enhances rotational strength, rated up to 12,000 RPM
• Smooth Daily Drivability: Near-stock pedal feel, perfect for street driving and moderate racing
• Solid-Hub Center Design: Seamlessly integrates with the OE dual-mass flywheel for optimal performance
• Torque Capacity: Rated to manage up to 440 lbs/ft, ensuring dependable strength for modified power levels

Recommended for daily, street, and moderate race applications.

Pair with T#363031 or any flywheel designed to be used with the E34 M5 clutch.

Upgraded clutch kit to be used with E34 M5 architecture flywheels. Designed for factory and upgraded street car applications to handle up to 375 Ft/lbs at the crank.

Whether you're replacing a worn-out clutch or upgrading for increased power handling, this E34 M5 clutch kit offers a reliable solution for enhanced pedal feel, power capacity, and overall driving satisfaction.

Paired with a modified geometry flywheel, the E34 M5 style clutch is ideally suited for most E36, E46, and others using the same powertrain. It checks all the boxes for essential clutch replacement features. While some aftermarket options may address slipping issues and worn-out clutches, they often sacrifice pedal feel, providing little to no resistance. A soft clutch not only kills the driving experience of your BMW but also reduces confidence when pushing the car to its limits.

On the contrary, you might be in the market for an upgraded clutch to handle your modified engine/forced induction builds. You go from an OE or aftermarket clutch option that has a lackluster and soft pedal feel to the complete opposite side of the spectrum, a very stiff clutch that grabs like an on-and-off switch making the clutch a pain almost undrivable on the street resulting in your favorite car turning into your least favorite car to drive.

The E34 M5 clutch kit balances performance with practicality, ensuring a satisfying driving experience whether you're maintaining your BMW or preparing it for increased power demands.

Kit Contents:

Performance Clutch Disc and Pressure plate
Throw-out Bearing
Clutch Alignment Tool
Pilot Bearing
Clutch features:

Torque Capacity (Crankshaft):
375 Ft / Lbs
Clutch Disc:
240mm Full face, performance organic friction material with integrated copper for enhanced heat dissipation and a long component life
OE-like friction backing plate design for smooth engagement with dual-stage damping springs to reduce gear noise and driveline chatter, and for smooth engagement
Pressure Plate:
Increased clamp force over OEM, rated at 1,729lbs of pressure
Throw-out Bearing:
OE spec for ease of installation and reliable operation
Clutch Alignment Tool:
BMW small 10 spline design, made for perfect fitment into the crank bore
Perfect clutch disc spline and size, easy removal with pull tab
​Not all aftermarket clutch kits include this proper alignment tool! We ensured you received the proper tool for trouble-free installation!
Fitment:
1992-1999 E36 BMW 323is 323ic 325i 325is 325ic 328i 328is 328ic M3
1999-2002 E46 BMW 323i 323ci 325i 325ci 328i 328ci 330i 330ci (5-speed)
1997-2002 Z3 BMW Z3 2.3 Z3 2.5i Z3 2.8 Z3 3.0i M Roadster M Coupe
2003-2005 E85 BMW Z4 2.5i Z4 3.0i (5-speed)
1977-1989 E24 BMW M6
1982-1988 E28 BMW M5
1987-1995 E34 BMW M5

BMW E46 M3 Stage 2 Daily Clutch Kit is designed to deliver impressive power handling and daily drivability for modified E46 M3s. Turner Motorsport offers this high-performance clutch kit, engineered to withstand increased horsepower and torque while maintaining a near-stock pedal feel. Featuring a heavy-duty pressure plate and high metal-content organic disc, this Stage 2 clutch kit is ideal for street driving, moderate racing, and daily performance needs.

With an enhanced clamp load that doesn’t compromise pedal pressure, this clutch kit is conservatively rated to handle up to 340 lbs/ft of torque. Its solid-hub center design ensures smooth compatibility with the OE dual-mass flywheel, making it a reliable choice for E46 M3 enthusiasts looking to upgrade their clutch system for increased durability and strength.

• Heavy-Duty Pressure Plate: Increased clamp load for enhanced torque capacity with minimal change in pedal pressure
• High Metal-Content Organic Disc: Boosts friction coefficient and rotational strength, rated for up to 12,000 RPM burst point
• Daily Drivability: Maintains a near-stock feel, perfect for street and moderate race applications
• Solid-Hub Center Design: Works seamlessly with the OE dual-mass flywheel for reliable performance
• Torque Handling: Conservatively rated to manage up to 340 lbs/ft of torque for added performance

Recommended for daily, street, and moderate race use.

BMW E46 E39 Stage 2 Daily Clutch Kit delivers a powerful yet smooth upgrade for drivers seeking enhanced performance without sacrificing daily comfort. Turner Motorsport presents this high-quality clutch kit, designed for BMW E46 and E39 models, with a heavy-duty pressure plate to handle high horsepower modifications. The organic disc material, enriched with metal content, provides double the friction coefficient of a standard clutch, ensuring maximum rotational strength up to 12,000 RPM.

This clutch kit is conservatively rated to handle up to 385 lbs/ft of torque, making it suitable for daily, street, and moderate race applications. Its solid-hub center section is perfectly compatible with the OE dual-mass flywheel, delivering a blend of strength, durability, and near-stock pedal feel.

• Heavy-Duty Pressure Plate: Enhanced clamp load for added torque capacity with minimal change in pedal pressure
• High Metal-Content Organic Disc: Increases friction coefficient and rotational strength, rated for up to 12,000 RPM
• Daily Drivability: Provides near-stock pedal feel, ideal for street driving and moderate racing
• Solid-Hub Center Design: Ensures smooth integration with the OE dual-mass flywheel
• Torque Capacity: Conservatively rated for 385 lbs/ft of torque, handling modified power levels with ease

Recommended for daily, street, and moderate race applications.

MINI R56 Stage 2 Endurance Clutch Kit is engineered for high-performance driving and racing environments. Designed to withstand the rigors of rally and endurance racing, this clutch kit delivers enhanced durability and performance while maintaining smooth operation.

• Precision Engineering: The pressure plate is precision-balanced to eliminate vibrations at high RPMs, ensuring stable performance.
• Improved Disengagement: Features an altered fulcrum for positive disengagement and quicker shifts.
• Dual Damped Disc: The disc’s Dual Damped design provides precise control during acceleration, particularly through corners.
• Hybrid Friction Material: Utilizes a Feramic (Sintered Iron) lining on the flywheel side and a high metal content Organic lining on the pressure plate side for positive engagement with a buffered feel.
• Compatibility: Designed to work with the stock dual mass flywheel. It is recommended to pair it with a new stock dual mass flywheel.
• Versatile Performance: Ideal for daily driving, street use, and excels in rally and endurance racing scenarios.

This Stage 2 Endurance Clutch Kit combines robust performance with reliable operation, making it a great choice for MINI enthusiasts who demand high performance under demanding conditions.

The factory dual-mass flywheel in W11-powered MINI Coopers was designed with comfort in mind—minimizing drivetrain vibration and delivering smoother shifts. However, this focus on refinement comes at a performance cost. The hefty 27 lbs. of rotational mass dulls throttle response, slows acceleration, and makes rev-matching more difficult. Dual-mass flywheels are also known to be less reliable in tuned or modified setups and can be expensive to replace when they fail.

ECS Tuning developed their Lightweight Single-Mass Flywheel to address these issues with a performance-focused alternative. Weighing in at just 17 lbs., this flywheel sheds nearly 10 lbs. of rotating mass compared to the OEM unit—transforming throttle response, acceleration, and clutch feel for a more engaging and dynamic driving experience.

Key Features:

Manufactured from 4140 Chromoly Steel
Heat-treated and tempered for exceptional strength, wear resistance, and thermal stability.
Optimized Hardness (HRC 28–32)
Ensures consistent performance and durability under extreme conditions.
Precision-Balanced to G16 Standard (175 g-mm)
Exceeds OEM balance requirements for smooth, high-RPM operation.
Black Oxide Finish
Provides effective corrosion resistance and a sleek appearance.
SFI 1.1 Certified
Validated for safe use in high-performance and racing environments.
Direct Fit
Engineered to work seamlessly with OE-style clutch kits designed for the W11 engine architecture.
Performance Benefits:

OEM Flywheel Weight: 27 lbs
ECS Lightweight Flywheel Weight: 17 lbs
This significant weight reduction results in:

Sharper throttle response
Faster engine revs and acceleration
Improved clutch engagement and feel
Increased performance potential for modified vehicles
OEM & Aftermarket Compatibility:

Replaces OE Flywheel #: 21207532057
Compatible Clutch Kits:
MINI OE: 21207551384
Spec: SB001, SB003
Clutch Masters: 03050HD00R
Recommended Hardware:

Flywheel Bolts: 11227560579 (Qty 8)
Pressure Plate Bolts: 21207520449 (Qty 6)