E30 Clutch Master Cylinder - Fits 318i 318is 325e 325i 325iC 325is 32...

We Price Match - Give Us A Call or Chat!

T#:3200

Part#: 21521156000

In Stock

$ 81.99

This product was last offered at the strikethrough price on
07-14-2026

$ 71.99 USD

Add to Wish List

Qty

$ 71.99 USD

Add to Wish List

This Clutch Master Cylinder (input cylinder). If you have noticed your pedal going to the floor or not being able to disengage the clutch the problem could be either this master cylinder or the clutch slave cylinder.

This item fits the following BMWs:
1984-1991 E30 BMW 318i 318is 318ic 325e 325es 325i 325ic 325is 325ix M3

Show More Show Less

Genuine BMW Throwout Bearing Guide Tube

T#:22686

Part#: 23111224845

In Stock

$ 110.99 USD

Add to Wish List

Qty

$ 110.99 USD

Add to Wish List

Replace this tube whenever the bearing or clutch kit is replaced.

Genuine BMW Guide Tube
This item fits the following BMW Chassis:
E36 M3,E34,E36,E39,E46,E53 X5

Show More Show Less

Genuine BMW Clutch Slave Cylinder - Multiple BMWs

T#:49238

Part#: 21526785964

In Stock

3% off MSRP $ 113.92

MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.

$ 109.99 USD

Add to Wish List

Qty

3% off MSRP

$ 113.92

MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.

$ 109.99 USD

Add to Wish List

On vehicles that have hydraulic clutches, the slave cylinder transmits pedal movements to the clutch pack. The hydraulic aspect of this system makes clutch engagement much more comfortable. Like any hydraulic system though, the corrosive brake fluid can wear out seals and cause leaking and failure. If this is the case on your car, the best solution for repair is replacing the defective part.

Show More Show Less

Genuine BMW Clutch Kit 6 Speed Manual Transmission - 21207603248 - E9...

T#:48901

Part#: 21207603248

In Stock

34% off MSRP $ 772.37

MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.

$ 509.99 USD

Add to Wish List

Qty

34% off MSRP

$ 772.37

MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.

$ 509.99 USD

Add to Wish List

This Genuine BMW OE replacement clutch kit from BMW comes stock for the 335is, 550i, and 650i. A lot of our customers install this as an upgrade for the 135i 335i and 535i!

Includes:

Clutch friction disc
Throwout/release bearing
Clutch fork lever
Pressure plate
Pressure plate bolts

Genuine BMW Clutch Kit for your 6 Speed Manual Transmission vehicle -
This item fits the following BMW Chassis:
E92,E93,F10,F12,F13

Show More Show Less

Genuine BMW Clutch Release/Throw-out Bearing

T#:367982

Part#: 21511223582

In Stock

8% off MSRP $ 109.99

MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.

$ 100.99 USD

Add to Wish List

Qty

8% off MSRP

$ 109.99

MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.

$ 100.99 USD

Add to Wish List

Ensure smooth clutch operation in your BMW with the Turner Motorsport Genuine BMW Clutch Release/Throw-out Bearing. This crucial component, situated between the clutch pressure plate and release fork lever, is essential for optimal performance. When renewing your clutch, don't overlook the importance of replacing this genuine BMW bearing.

Key Benefits:

Genuine BMW quality guarantees a perfect fit.
Prevents clutch-related issues for reliable performance.

Upgrade your BMW's clutch system with the Turner Motorsport Genuine BMW Clutch Release/Throw-out Bearing.

Show More Show Less

E36 M3, MZ3 JB Racing Lightweight Aluminum Flywheel

T#:3771

Part#: 520-010-240

Ships in 10 Business Days

$ 602.00 USD

Add to Wish List

Qty

$ 602.00 USD

Add to Wish List

Aluminum flywheels are much lighter than the stock steel flywheel and that produces better throttle response and more available horsepower to the wheels for faster acceleration. The JB Racing aluminum flywheels are a direct replacement for the stock flywheel and work with stock clutch components for an easy upgrade with very little downside.

Modern flywheels are built with additional components and features that are designed to dampen and minimize vibrations from the engine and transmission. As a result they have become bloated in weight and that means more energy is used up just making the flywheel spin. The weight difference between an aluminum and steel flywheel is huge - sometimes more than 50% less. Without the additional mass, more energy can be diverted to where it counts most - moving the car. The flywheel and clutch is one of the first areas that engine builders address when making the rotating assembly lighter for race engines. The dampening effect is just not needed on cars that are focused on performance.

In addition to releasing more power to the wheels, the lighter flywheel allows the engine to spin more freely, which improves throttle response. Again, the difference is huge as you watch the revs build faster than before. With the engine spinning easier the power band comes up much sooner. The stock steel flywheel feels lazy in comparison. There is a driving adjustment required to get used to how much faster the engine revs but that's not really a downside.

The JB lightweight flywheel is designed to be used with a factory organic clutch - the same clutch kit that you would get from any BMW dealer. This makes replacement clutch components easy to source and inexpensive when compared to specialized racing clutches. By using the factory BMW clutch, JB has also made the whole assembly easy to live with when used on the street. The clutch behaves the same as it originally did - just with better throttle response and more power! The JB flywheel can also be rebuilt with a new clutch contact surface - you don't have to buy a new flywheel.

Aluminum flywheels are considered 'single-mass' flywheels because they do not have the same dampening designs as an original 'dual-mass' flywheel. With a single-mass design more noise and vibration may be noticeable. There are steps you can take to minimize the noise - heavier weight transmission oil and clutch discs with anti-rattle springs (sprung-hub clutch). In addition to the standard replacement clutches, we also sell Sachs Performance sprung hub clutches that also work with the JB flywheels.

Stock Flywheel Weight = 25.5lbs
JB Flywheel Weight = 10.0lbs

This item fits the following BMWs:
1995-1999 E36 BMW M3
1998-2002 Z3 BMW Z3 M Roadster M Coupe

Show More Show Less

Clutch Slave Cylinder - E60 M5, E63 M6 w SMG transmission

T#:49734

Part#: 23017838938

In Stock

2% off MSRP $ 603.99

MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.

$ 592.99 USD

Add to Wish List

Qty

2% off MSRP

$ 603.99

MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.

$ 592.99 USD

Add to Wish List

This is a Genuine BMW clutch slave cylinder for E60 M5 and E63 MN6 with the SMG II GS7S47BG transmission. The slave draws fluid from the brake reservoir and applies it to the clutch fork/throw-out bearing. A bad slave cylinder could leave you stranded.

This item fits the following BMWs:
2006-2010 E60 BMW M5
2006-2010 E63 BMW M6

Show More Show Less

E30 318i/is, E36 318i, Z3 1.9 JB Racing Lightweight Aluminum Flywheel...

T#:3769

Part#: 520-040-215

Back Ordered

11% off MSRP $ 765.00

MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.

$ 679.00 USD

Add to Wish List

Qty

11% off MSRP

$ 765.00

MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.

$ 679.00 USD

Add to Wish List

Aluminum flywheels are much lighter than the stock steel flywheel and that produces better throttle response and more available horsepower to the wheels for faster acceleration. The JB Racing aluminum flywheels are a direct replacement for the stock flywheel and work with stock clutch components for an easy upgrade with very little downside.

Modern flywheels are built with additional components and features that are designed to dampen and minimize vibrations from the engine and transmission. As a result they have become bloated in weight and that means more energy is used up just making the flywheel spin. The weight difference between an aluminum and steel flywheel is huge - sometimes more than 50% less. Without the additional mass, more energy can be diverted to where it counts most - moving the car. The flywheel and clutch is one of the first areas that engine builders address when making the rotating assembly lighter for race engines. The dampening effect is just not needed on cars that are focused on performance.

In addition to releasing more power to the wheels, the lighter flywheel allows the engine to spin more freely, which improves throttle response. Again, the difference is huge as you watch the revs build faster than before. With the engine spinning easier the power band comes up much sooner. The stock steel flywheel feels lazy in comparison. There is a driving adjustment required to get used to how much faster the engine revs but that's not really a downside.

The JB lightweight flywheel is designed to be used with a factory organic clutch - the same clutch kit that you would get from any BMW dealer. This makes replacement clutch components easy to source and inexpensive when compared to specialized racing clutches. By using the factory BMW clutch, JB has also made the whole assembly easy to live with when used on the street. The clutch behaves the same as it originally did - just with better throttle response and more power! The JB flywheel can also be rebuilt with a new clutch contact surface - you don't have to buy a new flywheel.

Aluminum flywheels are considered 'single-mass' flywheels because they do not have the same dampening designs as an original 'dual-mass' flywheel. With a single-mass design more noise and vibration may be noticeable. There are steps you can take to minimize the noise - heavier weight transmission oil and clutch discs with anti-rattle springs (sprung-hub clutch).

Stock Flywheel Weight = 27.0lbs
JB Flywheel Weight = 9.0lbs

This item fits the following BMWs:
1989-1992 E30 BMW 318i 318is 318ic
1992-1997 E36 BMW 318i 318is 318ti 318ic
1996-1997 Z3 BMW Z3 1.9

Show More Show Less

E60, E82, E85, E9X, E89 (N52 Engine) JB Racing Lightweight Aluminum F...

T#:2801

Part#: 520-200-240

In Stock

$ 714.00 USD

Add to Wish List

Qty

$ 714.00 USD

Add to Wish List

Aluminum flywheels are much lighter than the stock steel flywheel and that produces better throttle response and more available horsepower to the wheels for faster acceleration. The JB Racing aluminum flywheels are a direct replacement for the stock flywheel and work with stock clutch components for an easy upgrade with very little downside.

Modern flywheels are built with additional components and features that are designed to dampen and minimize vibrations from the engine and transmission. As a result they have become bloated in weight and that means more energy is used up just making the flywheel spin. The weight difference between an aluminum and steel flywheel is huge - sometimes more than 50% less. Without the additional mass, more energy can be diverted to where it counts most - moving the car. The flywheel and clutch is one of the first areas that engine builders address when making the rotating assembly lighter for race engines. The dampening effect is just not needed on cars that are focused on performance.

In addition to releasing more power to the wheels, the lighter flywheel allows the engine to spin more freely, which improves throttle response. Again, the difference is huge as you watch the revs build faster than before. With the engine spinning easier the power band comes up much sooner. The stock steel flywheel feels lazy in comparison. There is a driving adjustment required to get used to how much faster the engine revs but that's not really a downside.

The JB lightweight flywheel is designed to be used with a factory organic clutch - the same clutch kit that you would get from any BMW dealer. This makes replacement clutch components easy to source and inexpensive when compared to specialized racing clutches. By using the factory BMW clutch, JB has also made the whole assembly easy to live with when used on the street. The clutch behaves the same as it originally did - just with better throttle response and more power! The JB flywheel can also be rebuilt with a new clutch contact surface - you don't have to buy a new flywheel.

Aluminum flywheels are considered 'single-mass' flywheels because they do not have the same dampening designs as an original 'dual-mass' flywheel. With a single-mass design more noise and vibration may be noticeable. There are steps you can take to minimize the noise - heavier weight transmission oil and clutch discs with anti-rattle springs (sprung-hub clutch).

This JB flywheel replaces the stock flywheel and can be used with either the stock 228mm or stock 240mm clutch discs. Depending on the model you may have either clutch size in your car but this flywheel is compatible with both. You can install a 240mm clutch as a mild upgrade.

Stock Flywheel Weight = 24-31.0lbs
JB Flywheel Weight = 12.0lbs

This item fits the following BMWs:
2006-2010 E60 BMW - 525i, 528i, 530i
2006-2013 E90, E91, E92, E93 BMW - 325i, 328i, 330i
2007-2013 E82 BMW - 125i, 128i
2006-2008 E85, E86 BMW - Z4 3.0i, Z4 3.0si
2009-later E89 BMW - Z4 3.0i

Show More Show Less

Genuine BMW Module, Clutch Switch - 61319122700 - E39 M5,E46 M3,E85 ...

The popular brown switch is no longer available

T#:16213

Part#: 61319122700

In Stock

$ 99.67 USD

Add to Wish List

Qty

$ 99.67 USD

Add to Wish List

If your clutch switch is bad, it will prevent the car from starting and seem similar to a bad starter, you will turn the key and nothing will happen. Replace yours to start your vehicle again.

Genuine BMW Module, Clutch Switch
This item fits the following BMW Chassis:
E39 M5,E46 M3,E85 Z4M,E39,E46,E85 Z4,E86 Z4

Show More Show Less

E46 M3 6MT JB Racing Lightweight Aluminum Flywheel

T#:302739

Part#: 520-180-240

Ships in 9 Business Days

$ 602.00 USD

Add to Wish List

Qty

$ 602.00 USD

Add to Wish List

Aluminum flywheels are much lighter than the stock steel flywheel and that produces better throttle response and more available horsepower to the wheels for faster acceleration. The JB Racing aluminum flywheels are a direct replacement for the stock flywheel and work with stock clutch components for an easy upgrade with very little downside.

Modern flywheels are built with additional components and features that are designed to dampen and minimize vibrations from the engine and transmission. As a result they have become bloated in weight and that means more energy is used up just making the flywheel spin. The weight difference between an aluminum and steel flywheel is huge - sometimes more than 50% less. Without the additional mass, more energy can be diverted to where it counts most - moving the car. The flywheel and clutch is one of the first areas that engine builders address when making the rotating assembly lighter for race engines. The dampening effect is just not needed on cars that are focused on performance.

In addition to releasing more power to the wheels, the lighter flywheel allows the engine to spin more freely, which improves throttle response. Again, the difference is huge as you watch the revs build faster than before. With the engine spinning easier the power band comes up much sooner. The stock steel flywheel feels lazy in comparison. There is a driving adjustment required to get used to how much faster the engine revs but that's not really a downside.

The JB lightweight flywheel is designed to be used with a factory organic clutch - the same clutch kit that you would get from any BMW dealer. This makes replacement clutch components easy to source and inexpensive when compared to specialized racing clutches. By using the factory BMW clutch, JB has also made the whole assembly easy to live with when used on the street. The clutch behaves the same as it originally did - just with better throttle response and more power! The JB flywheel can also be rebuilt with a new clutch contact surface - you don't have to buy a new flywheel.

Aluminum flywheels are considered 'single-mass' flywheels because they do not have the same dampening designs as an original 'dual-mass' flywheel. With a single-mass design more noise and vibration may be noticeable. There are steps you can take to minimize the noise - heavier weight transmission oil and clutch discs with anti-rattle springs (sprung-hub clutch). In addition to the standard replacement clutches, we also sell Sachs Performance sprung hub clutches that also work with the JB flywheels.

Stock Flywheel Weight = 25.0lbs
JB Flywheel Weight = 10.0lbs

This item fits the following BMWs:
2001-2006 E46 BMW M3 (6-speed manual only, not for SMG)

Show More Show Less

Stage 2+ Performance Clutch Kit (for SPEC single-mass flywheel) ...

T#:211063

Part#: SB533H-2

In Stock

$ 839.00 USD

Add to Wish List

Qty

$ 839.00 USD

Add to Wish List

Tuning your N54/N55 with all of the bolt-on upgrades? Don't allow your clutch or flywheel let you down! The stock clutch is fine for a stock car or just a simple software upgrade. But anything more and it quickly becomes the weak link (especially with drag races or hard launches). The 135i/335i/535i/Z4 35i SPEC Stage 2+ clutch kit is perfect for owners who want a performance clutch that works great with simple bolt-on modifications and will have a minimum of downsides or trade-offs. SPEC has spent considerable time and effort on the 335i models to produce a performance clutch and flywheel package that holds up to track and drag strip demands but is also easy to live with for daily driving. This clutch kit is meant to be used only with a SPEC flywheel. Features: The flywheel has a peak torque rating of 545ft-lbs Limitations of the stock flywheel are eliminated Self-adjusting, like the factory design, and the engagement point can be adjusted Sprung hub clutch to be used with the single-mass flywheel with near-stock levels of noise, vibration, and refinement **Due to the nature of lightened single mass flywheels added "NVH" or "chatter" will or may occur during operation. Accompanying modifications can also increase or decrease the amount of "NVH" or "chatter" in the drivetrain. Please contact our sales team with any questions.**

Show More Show Less

SPEC Clutch Super Twin Performance Clutch Kit - w/ Organic Trim - BMW...

T#:3457425

Part#: SB55SST

Back Ordered

$ 1,899.00 USD

Add to Wish List

Qty

$ 1,899.00 USD

Add to Wish List

SPEC Super Twin multi-disc clutch and flywheel kits are designed for street and track use in vehicles with extreme horsepower and torque (700 to 1500 lbs.-ft.). They offer near-stock drivability, tremendous life expectancy, a no shimming/setup bolt-in installation, and maintenance-free operation. With their all-billet construction, these assemblies are smooth and quiet. Super Twins are constructed with aircraft-grade aluminum and high-carbon billet steel milled to industry-leading .001 in. tolerances for perfect balance and actuation. Friction is provided by dampened, full-faced, carbon-graphite discs. Additional features of SPEC Super Twin multi-disc clutch and flywheel kits: Organic, fiber, and full-metallic versions are also available Flywheel and track-spec hardware are included in each kit *Rebuildable by SPEC or the end-user *Ideal for all types of use, including: street, drag racing, drifting, road racing, time-attack, pulling, and rally

Show More Show Less

SPEC Clutches Twin disc SS-Trim Clutch Kit - E60 M5, E63 E64 M6 SMG ...

T#:341298

Part#: SB60SST

Ships in 4 Business Days

$ 1,799.00 USD

Add to Wish List

Qty

$ 1,799.00 USD

Add to Wish List

When adding performance-enhancing modifications to your vehicle, you need a way to get the power to the wheels. The SPEC clutch kit is perfect for preventing premature wear and slippage during heavy acceleration. This kit is designed to hold up to 710 ft. lbs. For vehicles with SMG transmission only

Show More Show Less

Genuine BMW Clutch Slave Cylinder

T#:49244

Part#: 21526795713

Ships in 3 Business Days

4% off MSRP $ 113.99

MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.

$ 108.99 USD

Add to Wish List

Qty

4% off MSRP

$ 113.99

MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.

$ 108.99 USD

Add to Wish List

Genuine BMW Output Cylinder Clutch - D=22,20Mm
This item fits the following BMW Chassis:
F22,F30,F32,F33,F36,F80 M3,F82 M4,F83

Genuine BMW Clutch Release/Throw-out Bearing - E30 M3, E34 M5, Z3 M C...

T#:19645

Part#: 21512226729

Ships in 3 Business Days

6% off MSRP $ 116.99

MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.

$ 109.99 USD

Add to Wish List

Qty

6% off MSRP

$ 116.99

MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.

$ 109.99 USD

Add to Wish List

Genuine BMW Clutch Release Bearing - H=25mm
This item fits the following BMW Chassis:
E30 M3,E36 M3,E34 M5,E30,E34,E36

SPEC Billet Aluminum Single Mass Flywheel - E9X 335i, E82/88 135i, E6...

T#:387322

Part#: SB53A-2

In Stock

$ 579.00 USD

Add to Wish List

Qty

$ 579.00 USD

Add to Wish List

Aluminum flywheels are much lighter than the stock steel flywheel and that produces better throttle response and more available horsepower to the wheels for faster acceleration.

Genuine BMW Clutch Master Cylinder - E46 E9X E82 E39 and more ...

T#:367993

Part#: 21526773670

In Stock

9% off MSRP $ 233.99

MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.

$ 213.99 USD

Add to Wish List

Qty

9% off MSRP

$ 233.99

MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.

$ 213.99 USD

Add to Wish List

A leaking master cylinder often feels like a failing clutch or a problematic transmission

Genuine BMW Clutch Slave Cylinder

T#:367994

Part#: 21526775924

In Stock

7% off MSRP $ 190.39

MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.

$ 177.99 USD

Limited Qty Sale

Add to Wish List

Qty

7% off MSRP

$ 190.39

MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.

$ 177.99 USD

Limited Qty Sale

Add to Wish List

F-Chassis B58 SPEC Billet Aluminum Flywheel

T#:7036582

Part#: SBB58A-2

In Stock

$ 749.00 USD

Add to Wish List

Qty

$ 749.00 USD

Add to Wish List

These kits feature a non-SAC mechanism pressure plate, which , deviating from the original design, provides a lighter rotating assembly, higher rpm capability and greater clamp load levels. Required for the install is a billet rebuildable flywheel that features a lightweight, low MOI design and infinite rebuildability. The billet aluminum flywheel weighs 14lbs, and billet steel 22 lbs.

Show More Show Less

E46 323/325/328/330 5-speed, Z3 2.3/2.8/3.0 JB Racing Lightweight Alu...

T#:4227

Part#: 520-140-240

In Stock

$ 602.00 USD

Add to Wish List

Qty

$ 602.00 USD

Add to Wish List

Aluminum flywheels are much lighter than the stock steel flywheel and that produces better throttle response and more available horsepower to the wheels for faster acceleration. The JB Racing aluminum flywheels are a direct replacement for the stock flywheel and work with stock clutch components for an easy upgrade with very little downside.

Modern flywheels are built with additional components and features that are designed to dampen and minimize vibrations from the engine and transmission. As a result they have become bloated in weight and that means more energy is used up just making the flywheel spin. The weight difference between an aluminum and steel flywheel is huge - sometimes more than 50% less. Without the additional mass, more energy can be diverted to where it counts most - moving the car. The flywheel and clutch is one of the first areas that engine builders address when making the rotating assembly lighter for race engines. The dampening effect is just not needed on cars that are focused on performance.

In addition to releasing more power to the wheels, the lighter flywheel allows the engine to spin more freely, which improves throttle response. Again, the difference is huge as you watch the revs build faster than before. With the engine spinning easier the power band comes up much sooner. The stock steel flywheel feels lazy in comparison. There is a driving adjustment required to get used to how much faster the engine revs but that's not really a downside.

The JB lightweight flywheel is designed to be used with a factory organic clutch - the same clutch kit that you would get from any BMW dealer. This makes replacement clutch components easy to source and inexpensive when compared to specialized racing clutches. By using the factory BMW clutch, JB has also made the whole assembly easy to live with when used on the street. The clutch behaves the same as it originally did - just with better throttle response and more power! The JB flywheel can also be rebuilt with a new clutch contact surface - you don't have to buy a new flywheel.

Aluminum flywheels are considered 'single-mass' flywheels because they do not have the same dampening designs as an original 'dual-mass' flywheel. With a single-mass design more noise and vibration may be noticeable. There are steps you can take to minimize the noise - heavier weight transmission oil and clutch discs with anti-rattle springs (sprung-hub clutch). In addition to the standard replacement clutches, we also sell Sachs Performance sprung hub clutches that also work with the JB flywheels.

Stock Flywheel Weight = 25.0lbs
JB Flywheel Weight = 10.0lbs

This item fits the following BMWs:
1999-2002 E46 BMW 323i 323ci 325i 325ci 328i 328ci 330i 330ci (with 5-speed manual transmission)
2001-2005 E46 BMW 325xi 330xi
1997-2002 Z3 BMW Z3 2.3 Z3 2.5i Z3 2.8 Z3 3.0i

Show More Show Less

Stage 1 Performance Clutch Kit (for SPEC single-mass flywheel) ...

T#:397226

Part#: SB531-2

Ships in 4 Business Days

10% off MSRP $ 759.00

MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.

$ 683.99 USD

Part#: SB553H-2

In Stock at Vendor

$ 839.00 USD

Add to Wish List

Qty

$ 839.00 USD

Add to Wish List

SPEC Stage 2+ Performance Clutch Kit - E46 M3 6MT

T#:340444

Part#: SB663H

Ships in 3 Business Days

Starting at $ 869.00 USD

Add to Wish List

Starting at $ 869.00 USD

Add to Wish List

The SPEC Stage 2 clutch is a premium, no compromises heavy-duty clutch upgrade for the 2001-2006 E46 M3 (manual transmission). Where the stock clutch is well-known for premature wear when driven hard and the factory dual mass flywheel is a known failure point, the SPEC clutch delivers with an over-engineered, performance-oriented clutch solution. The single carbon-Kevlar clutch is rated at 545 ft-lbs, more than enough for the naturally-aspirated S54 engines. A heavy-duty pressure plate and throw-out bearing complete the package.

The stock clutch in the S54 cars is not a terrible clutch and it is not under-rated (it's the same clutch disc used in the E39 M5). Our tuned M3 street and race cars have used the stock clutch with almost 400hp with only the occassional slip. But if the clutch is not grabbing like you want it to, or your tuning plans will include forced induction, a heavy-duty clutch is what will be needed. The SPEC Stage 2 clutch consists of a carbon-Kevlar friction material paired with a heavy-duty pressure plate. The clutch is stronger and grabs harder than the factory clutch. It has a much more robust feel and engagement. And with this specification the clutch will never be a weak point. The SPEC clutch is designed to work with the stock dual mass flywheel or the SPEC single-mass flywheel (steel or aluminum).

The real weak point in the driveline is in the flywheel. The stock dual-mass flywheel has rubber damper discs inside that will wear out over time. Heat and aggressive driving will accelerate their wear. Even if the clutch contact surface is not showing wear the inner rubber linings most likely are. On most clutch replacements we strongly advise getting a new flywheel at the same time to avoid duplicating the work. You can use the SPEC clutch with the stock or SPEC flywheel. Both the SPEC steel and aluminum flywheels are lighter than stock and will be single-mass. There will be a lot more noise and 'gearbox chatter' with the aluminum but the tradeoff is a much better acceleration and quicker revving. For daily driver commuting you will probably be happiest with the stock flywheel. For the ultimate in sports car feel use the aluminum. For the best of both worlds select the SPEC steel flywheel. It will not fail like the dual mass design but still has enough mass to dampen most engine vibrations.

SPEC Clutch is one of the premier clutch and flywheel suppliers to the tuner market. They are often found on the most highly tuned import and domestic vehicles. They are recent players in the German car community with a special focus on the newer turbo BMW models with high torque output. SPEC has been proven time after time to provide superior performance, drivability, and longevity to the most hardcare enthusiasts around the globe.

E46 M3 SPEC Clutch Kit contents:
+ carbon-Kevlar clutch disc
+ heavy-duty pressure plate
+ heavy duty billet throw-out bearing

This item fits the following BMWs:
2001-2006 E46 BMW M3 with 6 speed manual transmission

Show More Show Less

Genuine BMW Clutch Release/Throw-Out Bearing

T#:12563

Part#: 21517521471

In Stock

4% off MSRP $ 110.53

MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.

$ 106.39 USD

Add to Wish List

Qty

4% off MSRP

$ 110.53

MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.

$ 106.39 USD

Add to Wish List

Genuine BMW Clutch Release Bearing -
This item fits the following BMW Chassis:
E30,E34,E36,E39,E46,E53 X5,E85

Genuine BMW Throwout Bearing Guide Tube

T#:49868

Part#: 23117531354

Ships in 3 Business Days

2% off MSRP $ 84.99

MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.

$ 82.99 USD

Add to Wish List

Qty

2% off MSRP

$ 84.99

MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.

$ 82.99 USD

Add to Wish List

Genuine BMW Guide Tube
This item fits the following BMW Chassis:
E85 Z4M,E46,E53 X5,E83 X3,E85 Z4,E86 Z4,E90,E92

BMW N54 N55 B58 SPEC Stage 2 Performance Clutch Kit (for SPEC single-...

T#:341710

Part#: SB532-2

In Stock

$ 790.99 USD

Add to Wish List

Qty

$ 790.99 USD

Add to Wish List

SPEC's Stage 2 clutch features a full faced pure Kevlar disc complete with steel backing. This lining offers outstanding drivability like the Stage 1 kit, with an increased torque capacity and a longer life. The hub is double sprung with built-in spring reliefs for flexibility, along with heat treatment for added strength and durability. This clutch is best served in any situation from daily driven on the street, to drag or autocross racing events.

Kit includes:

Pressure plate
Clutch disc
Pilot bearing
Clutch Release Bearing
Clutch Alignment Tool
Clutch fork
Designed to be used with billet single mass flywheel

Show More Show Less

Genuine BMW Camshaft Alignment Tool - S54

T#:20446

Part#: 83300493749

In Stock

$ 224.99 USD

Add to Wish List

Qty

$ 224.99 USD

Add to Wish List

Genuine BMW AUXILIARY MATERIALS, FLUIDS / COLORSYSTEM TEMPLATE

E39 540i 97-03 JB Racing Lightweight Aluminum Flywheel

T#:1339

Part#: 520-150-240

In Stock

$ 903.00 USD

Add to Wish List

Qty

$ 903.00 USD

Add to Wish List

Aluminum flywheels are much lighter than the stock steel flywheel and that produces better throttle response and more available horsepower to the wheels for faster acceleration. The JB Racing aluminum flywheels are a direct replacement for the stock flywheel and work with stock clutch components for an easy upgrade with very little downside.

Modern flywheels are built with additional components and features that are designed to dampen and minimize vibrations from the engine and transmission. As a result they have become bloated in weight and that means more energy is used up just making the flywheel spin. The weight difference between an aluminum and steel flywheel is huge - sometimes more than 50% less. Without the additional mass, more energy can be diverted to where it counts most - moving the car. The flywheel and clutch is one of the first areas that engine builders address when making the rotating assembly lighter for race engines. The dampening effect is just not needed on cars that are focused on performance.

In addition to releasing more power to the wheels, the lighter flywheel allows the engine to spin more freely, which improves throttle response. Again, the difference is huge as you watch the revs build faster than before. With the engine spinning easier the power band comes up much sooner. The stock steel flywheel feels lazy in comparison. There is a driving adjustment required to get used to how much faster the engine revs but that's not really a downside.

The JB lightweight flywheel is designed to be used with a factory organic clutch - the same clutch kit that you would get from any BMW dealer. This makes replacement clutch components easy to source and inexpensive when compared to specialized racing clutches. By using the factory BMW clutch, JB has also made the whole assembly easy to live with when used on the street. The clutch behaves the same as it originally did - just with better throttle response and more power! The JB flywheel can also be rebuilt with a new clutch contact surface - you don't have to buy a new flywheel.

Aluminum flywheels are considered 'single-mass' flywheels because they do not have the same dampening designs as an original 'dual-mass' flywheel. With a single-mass design more noise and vibration may be noticeable. There are steps you can take to minimize the noise - heavier weight transmission oil and clutch discs with anti-rattle springs (sprung-hub clutch).

Stock Flywheel Weight = 33.0lbs
JB Flywheel Weight = 13.0lbs

This item fits the following BMWs:
1997-2003 E39 BMW 540i

Show More Show Less

Valeo Single Mass Clutch Kit - E46 325xi (Thru 08/03), 330i 5 speed (...

We Price Match - Give Us A Call or Chat!

T#:3578

Part#: 21207531843

Ships in 2 Business Days

$ 896.33 USD

Add to Wish List

Qty

$ 896.33 USD

Add to Wish List

Single mass flywheels can be resurfaced while it is recommended that dual mass flywheels are not.
Dual mass flywheels contain a rubber damper that will wear out, single mass flywheels do not have this and are inherently easier to maintain
Single mass flywheels also provide more consistent clutch feel when compared to the dual mass "self-adjusting" clutch that is notorious for inconsistency.
Valeo's single mass flywheel conversion is designed to be a similar weight and mass to OEM, making it an ideal choice for a daily driver

Show More Show Less

E24 633/635CSi/M6, E28 535i/M5 JB Racing Lightweight Aluminum Flywhee...

T#:3770

Part#: 520-080-240

Ships in 9 Business Days

$ 630.00 USD

Add to Wish List

Qty

$ 630.00 USD

Add to Wish List

Aluminum flywheels are much lighter than the stock steel flywheel and that produces better throttle response and more available horsepower to the wheels for faster acceleration. The JB Racing aluminum flywheels are a direct replacement for the stock flywheel and work with stock clutch components for an easy upgrade with very little downside.

Modern flywheels are built with additional components and features that are designed to dampen and minimize vibrations from the engine and transmission. As a result they have become bloated in weight and that means more energy is used up just making the flywheel spin. The weight difference between an aluminum and steel flywheel is huge - sometimes more than 50% less. Without the additional mass, more energy can be diverted to where it counts most - moving the car. The flywheel and clutch is one of the first areas that engine builders address when making the rotating assembly lighter for race engines. The dampening effect is just not needed on cars that are focused on performance.

In addition to releasing more power to the wheels, the lighter flywheel allows the engine to spin more freely, which improves throttle response. Again, the difference is huge as you watch the revs build faster than before. With the engine spinning easier the power band comes up much sooner. The stock steel flywheel feels lazy in comparison. There is a driving adjustment required to get used to how much faster the engine revs but that's not really a downside.

The JB lightweight flywheel is designed to be used with a factory organic clutch - the same clutch kit that you would get from any BMW dealer. This makes replacement clutch components easy to source and inexpensive when compared to specialized racing clutches. By using the factory BMW clutch, JB has also made the whole assembly easy to live with when used on the street. The clutch behaves the same as it originally did - just with better throttle response and more power! The JB flywheel can also be rebuilt with a new clutch contact surface - you don't have to buy a new flywheel.

Aluminum flywheels are considered 'single-mass' flywheels because they do not have the same dampening designs as an original 'dual-mass' flywheel. With a single-mass design more noise and vibration may be noticeable. There are steps you can take to minimize the noise - heavier weight transmission oil and clutch discs with anti-rattle springs (sprung-hub clutch).

Stock Flywheel Weight = 22.0lbs
JB Flywheel Weight = 8.5lbs

This flywheel includes the ignition trigger wheel.

This item fits the following BMWs:
1982-1987 E23 BMW 733i 735i
1982-1989 E24 BMW 633csi 635csi M6
1985-1988 E28 BMW 535i 535is M5

Show More Show Less

Genuine BMW Clutch Slave Cylinder - E83, Z4, E46

T#:12267

Part#: 21526785966

Ships in 3 Business Days

6% off MSRP $ 223.99

MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.

$ 210.99 USD

Add to Wish List

Qty

6% off MSRP

$ 223.99

MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.

$ 210.99 USD

Add to Wish List

GENUINE BMW OUTPUT CYLINDER,CLUTCH:211042

We sell an aftermarket version of this part for considerable less # 21526766279

Show More Show Less

Genuine BMW Water Pump (Includes Alignment Dowel) - E46 M3

T#:1482

Part#: 11517838118

In Stock

6% off MSRP $ 632.99

MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.

$ 595.99 USD

Add to Wish List

Qty

6% off MSRP

$ 632.99

MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.

$ 595.99 USD

Add to Wish List

The E46 M3 does not suffer from the cooling nightmares of the previous E36 models. The original water pump uses a composite impeller, not plastic or metal, so the BMW pump will typically last 85,000+ miles before the bearings show signs of wear (the composite impeller is not the reason for preventative maintenance - it's the bearings). We prefer the OE BMW pump to the aftermarket brands because it uses the composite impeller, it has a proven reliability record, and the pricing represents a solid value upgrade. The pump is located on the front of the engine with the fan attached to it. The complexity of the S54 engine means the water pump has multiple gaskets and seals that should also be replaced. And if the thermostat has not been changed then this is the best time for a new one as well.

Composite vs Metal
BMW designed this water pump to use a composite impeller. It is much stronger than the plastic pieces that were so problematic in the mid-90s. The aftermarket solution to the plastic issues was to use a metal impeller. This solved the impeller issues but created some others. The metal impeller is heavier than composite or plastic and that led to quicker bearing failure on the E36 pump (sometimes within a year). The possibility exists that the same premature bearing failure can happen on the E46 M3 metal impeller pumps as well. The heavier weight also has the drawback of using more horsepower since it requires more effort to move the heavier piece. The composite materials solve all of these issues - light weight, strong, long lasting, and relatively inexpensive. They also come with a two-year warranty (most aftermarket pumps are one year). Original BMW water pumps for the E36 (and most other modern BMWs) now use a composite impeller so any issues with factory pumps are long gone. Original BMW water pumps for the E46 M3 are known to last over 100,000 miles and the composite is still in excellent condition (failure is usually typical leaks from worn bearings). For preventative maintenance we recommend a replacement around 85,000 miles. Alternate part numbers: 11517838118, 11517838159.

This item fits the following BMWs:
2001-2006 E46 BMW M3

Show More Show Less

Stage 3+ Performance Clutch Kit (for SPEC single-mass flywheel) ...

T#:209171

Part#: SB533F-2

In Stock

$ 979.00 USD

Add to Wish List

Qty

$ 979.00 USD

Add to Wish List

The Stage 3+ is for cars making serious levels of boost and torque. If you have upgraded turbos or a single-turbo conversion, or have checked off the list of full bolt-ons, this will be a very capable clutch for you. This clutch is designed to work only with a SPEC single-mass flywheel and avoid the pitfalls of the stock OEM flywheel. The stock dual mass flywheel uses springs and rubber to isolate vibrations from the engine and transmission. However, on high mileage or abused flywheels the rubber can break down and the springs will become weak. A worn dual mass flywheel limits the amount of torque you can put out. It will affect clutch engagement, shifts, and power delivery. In some cases a total flywheel failure can rip apart the flywheel, clutch, and even transmission housing. With the SPEC single-mass flywheel the limitations of the stock flywheel are eliminated. The SPEC flywheel is a single mass design (no internal springs or rubber to fail) and is offered in a steel or aluminum material. The steel will better dampen vibration than the aluminum so it's the better choice for street use. The aluminum will have greater vibration and noise (gearbox rattle) that may not be acceptable for everyone. The clutch in this Stage 3+ kit is a sprung hub design so SPEC has done all they can to minimize the noise and vibration. It's also self-adjusting, like the factory design, and the engagement point can be adjusted. For use with SPEC Billet Flywheel (E-Chassis cars) or (F-Chassis cars)

Show More Show Less

Genuine BMW Clutch Kit - G80 M3, G82/83 M4, G87 M2 (Manual Trans) ...

T#:5362914

Part#: 21219505034

Ships in 3 Business Days

15% off MSRP $ 1,433.99

MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.

$ 1,220.99 USD

Add to Wish List

Qty

15% off MSRP

$ 1,433.99

MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.

$ 1,220.99 USD

Add to Wish List

This Genuine BMW replacement clutch kit includes a clutch disc, pressure plate, fork, release bearing, and bolts. No core charge

Genuine BMW Clutch Slave Cylinder

T#:174558

Part#: 21521157212

Ships in 3 Business Days

6% off MSRP $ 242.99

MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.

$ 228.99 USD

Add to Wish List

Qty

6% off MSRP

$ 242.99

MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.

$ 228.99 USD

Add to Wish List

Genuine BMW Output Cylinder Clutch - D=20,64mm
This item fits the following BMW Chassis:
E30 M3,E30

Genuine BMW Clutch Master Cylinder

T#:367991

Part#: 21526758829

Ships in 3 Business Days

6% off MSRP $ 257.99

MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.

$ 242.99 USD

Add to Wish List

Qty

6% off MSRP

$ 257.99

MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.

$ 242.99 USD

Add to Wish List

Genuine BMW Set Of Electric Motors - 23017841032 -E60 M5,E63 M6 ...

T#:25150

Part#: 23017841032

Ships in 3 Business Days

2% off MSRP $ 976.99

MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.

$ 952.99 USD

Add to Wish List

Qty

2% off MSRP

$ 976.99

MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.

$ 952.99 USD

Add to Wish List

Genuine BMW electric motor that powers the SMG Pump.

Genuine BMW Set Of Electric Motors
This item fits the following BMW Chassis:
E60 M5,E63 M6,E63

Show More Show Less

Genuine BMW Pressure Accumulator - E60 M5 S85 5.0L

T#:49731

Part#: 23017838933

Ships in 5 Business Days

2% off MSRP $ 1,110.99

MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.

$ 1,087.99 USD

Add to Wish List

Qty

2% off MSRP

$ 1,110.99

MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.

$ 1,087.99 USD

Add to Wish List

Genuine BMW Pressure Accumulator
This item fits the following BMW Chassis:
E60 M5,E63 M6,E63

Clutch Slave Cylinder - E46 M3 SMG

T#:4653

Part#: 21522229841

Ships in 3 Business Days

6% off MSRP $ 444.99

MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.

$ 418.99 USD

Add to Wish List

Qty

6% off MSRP

$ 444.99

MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.

$ 418.99 USD

Add to Wish List

The slave draws fluid from the brake reservoir and applies it to the clutch fork/throw-out bearing. A bad slave cylinder could leave you stranded. Also a must for when upgrading to an M3 flywheel/clutch assembly. Only for E46 M3 with SMG transmission.

This item fits the following BMWs:
2001-2006 E46 BMW M3 Coupe M3 Convertible

Show More Show Less

Spec Aluminum Single Mass Flywheel - E9X 335 (01/2009+)

Designed for use with SPEC SB53X-2 clutch kits

T#:342330

Part#: SB53A-3

Back Ordered

$ 579.00 USD

Add to Wish List

Qty

$ 579.00 USD

Add to Wish List

Aluminum flywheels are much lighter than the stock steel flywheel and that produces better throttle response and more available horsepower to the wheels for faster acceleration.

Single Mass Flywheel Conversion Kit 52151203 - R52 / R53

We Price Match - Give Us A Call or Chat!

T#:585277

Part#: 52151203

In Stock

$ 585.99 USD

Add to Wish List

Qty

$ 585.99 USD

Add to Wish List

Valeo Dual Mass Flywheel Conversion Kit for MINI Cooper S/JCW

Elevate your MINI's performance with the Valeo dual mass flywheel conversion kit. This comprehensive kit includes a solid flywheel, pressure plate, clutch disc, throw-out bearing, and more. Notably, it replaces the OE dual mass flywheel for enhanced performance.

If you're missing any hardware, don't worry. Valeo ensures your satisfaction by replacing missing items with your order number. They are also working on an improved box design to prevent damage during shipping.

Designed for the R53/R52 Cooper S/JCW with W11 engines (Supercharged Engines), this kit is not compatible with Gen 2 MINIs (R56) with N14/N18+ Turbo Engines. For an exclusive ECS Tuning kit with extra seals, explore ES3469345.

Upgrade to the single mass setup for cost-efficiency, serviceability, simplicity, and enhanced driveability. Valeo's conversion kit maintains clutch and flywheel weight for quiet and easy driving.

This kit includes a replacement flywheel, clutch disc, pressure plate, release bearing, and more. Please note that a lightened single mass flywheel may result in some "NVH" or "chatter" during operation, which can be influenced by accompanying modifications.

For complete install kits, discover ES3469345 and ES4067131, exclusively at ECS Tuning.

Installation Details:

Flywheel bolts (M10x19.5): Tightening torque 90 Nm, Thread lock red.
Pressure plate (M7x26): Tightening torque 20 Nm.

Show More Show Less

Project Cars

SELECT YOUR BMW

BMW Performance Clutch Kits & Parts

Sub-Categories

Key Benefits:

Enhance Your Car's Performance with the Perfect Clutch-Flywheel Combination

Valeo Dual Mass Flywheel Conversion Kit for MINI Cooper S/JCW

Select Vehicle

Purpose

Category

Brand

Price

Special Offers

Shipping

Narrow Results